2BU88LD1430RFLD1430RF

NEW TECHNOLOGICAL STANDARD REQUIREMENTS FOR NEW RF PRODUCTS 1. Constant light output when operating on battery power. 2. CRI > 90. 3. CCT Stepping: 2200K – 2700K – 3000K – 4000K. 4. DIMMING Step Cycle: 100% – 75% – 50% – 25% – OFF – 100% – 75% – ...... 5. 2A charging (full charge in no more than 3 hours). 6. OVP (Over Voltage Protection). 7. Product is supplied without a plug-in charging power supply. 8. Round, white charging cable with USB Type-C connector (compatible with PD charging). o L = 1100mm for table models. o L = 1800mm for floor or reading models. 9. Thermal protection for the battery against overheating. 10. BATTERY LIFE of at least 8 hours at 100% intensity. PRODUCT USAGE FUNCTIONALITY: STANDARD MODE (Without Remote Control) 1. Switching OFF (from ON state): Long-press the touch control for 1 second. 2. LED Indicator Colors: o Red: Battery status (charging/low battery). o Green: Battery status (fully charged). o Blue: Kelvin (CCT) selection mode. o Pink: Timer mode active. 3. Dimming: o STEP Cycle: 100% – 75% – 50% – 25% – OFF – 100% – 75% – ...... o No dimming memory in manual mode. Every time the lamp is turned ON from an OFF state, it always starts at 100% light intensity, regardless of the previous setting. o ((ONLY and EXCLUSIVELY for POLDINA lamp: every time the lamp is turned ON (with a touch) from an OFF state, both the TOP and BOTTOM lights are lit and ON), regardless of whether the TOP light was previously deactivated by remote control )) 4. Kelvin (CCT) Change: With the lamp OFF, long-press the touch control for 3 seconds to enter Kelvin selection (Blue LED turns on). Each subsequent tap cycles through the steps: 4000K → 3000K → 2700K → 2200K. Press and hold for 2 seconds to confirm the chosen Kelvin and turn the lamp OFF. 5. CHARGING/BATTERY Status LED Indicator Signals: o Battery < 10%: Flashing red light (or flashing pink light if Timer mode is active). o Battery < 3%: The main light flashes 3 times + the status LED indicator blinks RED 3 times, then the lamp switches OFF automatically. o Battery < 3%: RF is temporarily deactivated. RF functionality reactivates once the lamp is charged to >3% capacity. 6. Factory SETTINGS Reset: o Procedure: Performed ONLY when the main light is ON and the lamp is NOT on the charging base. Press and hold the touch control for 8 seconds. o Confirmation: After 8 seconds, the main LED light flashes twice + the status LED indicator blinks WHITE twice, reverts to factory defaults (4000K, 100% intensity), and then switches OFF into "Sleep" mode. o Result: All lamp and RF functions go offline, and the lamp's memory is completely erased (like new). All previously paired/saved remotes are removed from memory. o A quick touch "wakes up"/turns ON the lamp, reactivating all functions except RF (to activate RF go to “Section 1: Remote Control Pairing – point 3”) PRODUCT USAGE FUNCTIONALITY : RF MODE (With Remote Control) IMPORTANT: The remote control must be paired with the lamp before use. Without pairing, the lamp will not respond to commands. Section 1: Remote Control Pairing Step-by-Step Pairing Procedure: 1. The lamp is delivered in a "Sleep" state. Wake the lamp with a quick tap on its touch control. 2. All lamp functions are now active except for RF (remote control functionality). 3. RF Activation / Entering Pairing Mode: o This step must be performed ONLY and EXCLUSIVELY when the main LED light is ON and the lamp is placed on its charging base. o Press and hold the lamp's touch control for 8 seconds to activate RF/Pairing Mode. The main light will flash twice and the status LED will blink WHITE twice to confirm that Pairing Mode is active. o You have 1 minute after RF activation to complete the pairing process. o Press the Pairing button (Pairing Key) on the remote control. The main light will flash twice to confirm command receipt and that the lamp has been successfully paired. Important Notes: • Pairing Mode automatically deactivates after 1 minute. • If pairing fails, repeat the procedure starting from point 3 above. Section 2: Remote Control Functions 1. Switching ON/OFF (Group 2): o Use the red (OFF) and green (ON) buttons on the remote. o Dimming Memory Function with Remote: Every time the lamp is turned ON (from an OFF state) using the remote's green button, it lights up at the previously set light intensity. ▪ Example: Turn the lamp ON with the remote's green button → Set light intensity to 25% using the remote → Turn the lamp OFF with the red button → Turn the lamp ON again with the green button. The lamp will light at 25% intensity due to the memory function. 2. Step Dimming (Group 6): Use the dedicated remote buttons to set intensity levels to 25%, 50%, 75%, or 100%. 3. Kelvin (CCT) Change (Group 5): Use the dedicated remote buttons to select the light color: 4000K, 3000K, 2700K, or 2200K. 4. Touch Control Lock/Unlock (Group 3) – Prevents accidental activation by locking the lamp's touch controls. o Lock Touch Controls: ▪ Press the closed padlock button on the remote. ▪ The lamp's LEDs will flash twice to confirm. o Unlock Touch Controls: ▪ Press the open padlock button on the remote. ▪ The lamp's LEDs will flash twice to confirm. o Important Note: While the lamp is on the charging base, the Lock/Unlock function is automatically disabled and cannot be activated. If you press the Lock/Unlock buttons during charging, the lamp will not react or emit any confirmation flashes. 5. Jolly Buttons (Group 4): o Jolly 1: Disables the top light (ONLY FOR POLDINA model) o Jolly 2: Activates the top light (ONLY FOR POLDINA model) o Jolly 0: Disables the charge status LED (only effective during charging). o Jolly 1 + Jolly 2 (Pressed Together): Sets a 1-hour timer. ▪ The timer can be activated ALSO while the lamp is on the charging base (only after RF has been reactivated). ▪ The main LED light flashes twice to confirm timer activation. ▪ LED indicator remains steadily lit for the duration of the timer countdown with a PINK colour ▪ LE…

Text truncated - open the document above for the full version.

Zafferano America LLC 092723-17 rev 10 Certification Application Attestation Statements Date: April 24, 2026 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern: Statement for 47 CFR section 2.911(d)(5)(i) ______Zafferano America LLC ______ certifies that as of the date of the application the equipment for which authorization is sought is not “covered” equipment 1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not “covered” equipment. Additional Explanation: <N/A> Statement for 47 CFR section 2.911(d)(5)(ii) ______Zafferano America LLC ______ (“the applicant”) certifies that, as of the date of the filing of this application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates – see KDB 986446 Question 5) as an entity producing “covered” equipment. The applicant also certifies that the device does not have cybersecurity and/or anti-virus software produced by Kaspersky Lab, Inc or any of its successors and assignees identified on the covered list installed on the device, nor will it be installed by the applicant at any time after certification. Thank you, By: __________________________ _____Barrett Gross___________________ (Signature 2 ) (Print name) Title: ______President_______ Company: ____Zafferano America LLC ___ Telephone: ______201-355-2400________ 1 - The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist . 2 - Letters must be placed on appropriate letterhead.

Zafferano America LLC 092723-17 Rev 10 U.S. Agent Designation for Service of Process (Applicant is Both Grantee and U.S. Agent) TO: American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 ATTENTION: FCC Certification – Section 2.911(d)(7) Information This letter is to confirm that the Applicant will also serve as the U.S. Agent for Service of Process as required by 47 CFR 2.911(d)(7). The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The Applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information changes. Applicant Company name: Zafferano America LLC FRN #: 0038119103 Grantee Code: 2BU88 Contact Name: Barrett Gross Street Address: 301 Penhorn Ave Ste 5 City/Province/Zip: Secaucus, NJ 07094 Telephone No: 201-355-2400 Email: info@zafferanoamerica Applicant Signature 2 : Date: January 23, 2026 Signed by (Printed Name/Title): Barrett Gross / President 2 - Letters must be placed on appropriate letterhead. The signee for the applicant must be one of the following: Applicant (grantee) contact of record in the FCC’s authorization system, or authorized officers or employee of the applicant (grantee).

Zafferano America LLC 050222-17 Authority to Act as Agent Date: April 24, 2026 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern: ______Intertek Testing Services (Shanghai FTZ) Co., Ltd.______ is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: _____(January 22, 2027)_____ By: __________________________ _______ Barrett Gross_________ (Signature 1 ) (Print name) Title: ____President__________ On behalf of: _____ Zafferano America LLC_____________________ (Company Name) Telephone: ____201-355-2400_________ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Zafferano America LLC 050222-17 Request for Confidentiality Date: April 24, 2026 Subject: Confidentiality Request for: ______(FCC ID: 2BU88LD1430RF)______ Pursuant to FCC 47 CFR 0.457(d) and 0.459 and/or IC RSP-100, Section 12.4, the applicant requests that a part of the subject application(s) be held confidential. Type of Confidentiality Requested Exhibit ☐ Short Term ☒ Permanent Block Diagrams ☐ Short Term --------------------------- External Photos ☐ Short Term ☐ Permanent * 1 Internal Photos ☐ Short Term ☒ Permanent Operation Description/Theory of Operation ☐ Short Term ☐ Permanent Parts List & Placement/BOM ☐ Short Term ☐ Permanent Tune-Up Procedure ☐ Short Term ☒ Permanent Schematics ☐ Short Term --------------------------- Test Setup Photos ☐ Short Term ☐ Permanent * 1 User’s Manual ______(Zafferano America LLC)______ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality for FCC Applications: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of __ (specify number of days not to exceed 180) 2 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Short Term Confidentiality for Industry Canada Applications: Starting May 2022, ISED will recognize short term confidentiality on certain exhibits until the intended date of marketing. The applicant requests the exhibits selected above as short term confidential be withheld from public view until: (specify ISED expiration date / date of marketing) . Sincerely, By: __________________________ _______Barrett Gross_________ (Signature/Title 3 ) (Print name) 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at: https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Please refer to https://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Page 1 of 2 External Photos Page 2 of 2

8054346790394 FCC ID: 2BU88LD1430RF

The label will be adhered to the side of the product with permanent adhesive

Page 1 of 3 Internal Photos Page 2 of 3 Page 3 of 3 Antenna

Zafferano America LLC SAR COMPLIANCE REPORT Report Type: FCC SAR assessment report Model: LD1430RF REPORT NUMBER: 2601B1229SHA-002 ISSUE DATE: April 24, 2026 DOCUMENT CONTROL NUMBER: TTRFFCCSAR-01_V1 © 2018 Intertek Intertek Testing Services (Shanghai FTZ) Co., Ltd Building No.86, 1198 Qinzhou Road (North) Caohejing Development Zone Shanghai 200233, China Telephone: 86 21 6127 8200 www.intertek.com TEST REPORT This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. TTRFFCCSAR-01_V1© 2018 Intertek Page 2 of 8 Report no.: 2601B1229SHA-002 Applicant : Zafferano America LLC 301 Penhorn Ave, Ste 5, Secaucus NJ 07094 Manufacturer : Qingdao Bozu International Trading Co.,Ltd No 166, Taoyuanhe 2nd Road, Huanxiu Street, Jimo District 266201, Qingdao, CHINA FCC ID : 2BU88LD1430RF SUMMARY: The equipment complies with the requirements according to the following standard(s) or Specification: KDB 447498 D01 General RF Exposure Guidance v06 FCC Part2.1093 FCC Part1.1307(b) PREPARED BY: REVIEWED BY: Erick Liu Wakeyou Wang Project Engineer Reviewer Report No.: 2601B1229SHA-002 TEST REPORT TTRFFCCSAR-01_V1© 2018 Intertek Page 3 of 8 Revision History Report No. Version Description Issued Date 2601B1229SHA-002 Rev. 01 Initial issue of report April 24, 2026 Report No.: 2601B1229SHA-002 TEST REPORT TTRFFCCSAR-01_V1© 2018 Intertek Page 4 of 8 1 GENERAL INFORMATION 1.1 Description of Equipment Under Test (EUT) Product name: REMOTE CONTROL Type/Model: LD1430RF Description of EUT: The product is a remote control for portable use. Rating: 1.5V Battery*2 Category of EUT: Class B EUT type: Table top Floor standing Software Version: / Hardware Version: / Sample received date: January 23, 2026 Date of test: January 23, 2026– January 24, 2026 1.2 Technical Specification Operation Frequency: 433.92MHz Type of Modulation: FSK Product Type: Mobile Portable Fix Location Channel Number: 1 Antenna Designation: Internal antenna Note: This information is supplied by the applicant. Any change in this value would result in different test data / conclusion. Report No.: 2601B1229SHA-002 TEST REPORT TTRFFCCSAR-01_V1© 2018 Intertek Page 5 of 8 1.3 Description of Test Facility Name: Intertek Testing Services (Shanghai FTZ) Co., Ltd. Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Telephone: 86 21 61278200 Telefax: 86 21 54262353 The test facility is recognized, certified, or accredited by these organizations: CNAS Accreditation Lab Registration No. CNAS L21189 FCC Accredited Lab Designation Number: CN0175 IC Registration Lab CAB identifier: CN0014 VCCI Registration Lab Registration No.: R-14243, G-10845, C-14723, T-12252 A2LA Accreditation Lab Certificate Number: 3309.02 Report No.: 2601B1229SHA-002 TEST REPORT TTRFFCCSAR-01_V1© 2018 Intertek Page 6 of 8 2 SAR Assessment Test result: Pass 2.1 SAR Test Exclusion Limit 100 MHz – 6 GHz and ≤ 50 mm Report No.: 2601B1229SHA-002 TEST REPORT TTRFFCCSAR-01_V1© 2018 Intertek Page 7 of 8 100 MHz – 6 GHz and > 50 mm < 100 MHz and < 200 mm Report No.: 2601B1229SHA-002 TEST REPORT TTRFFCCSAR-01_V1© 2018 Intertek Page 8 of 8 2.2 Assessment Results As we can see from the test report 2601B1229SHA-001: EIRP (dBm) = Field Strength (dBμV/m) + 20log 10 (D)−104.8, where D = 3m, EIRP (dBm) = 86.3 + 9.5 - 104.8 = -9.0dBm = 0.13mW. 0.13mW < 22mW (Test Exclusion Thresholds of 450MHz at 5mm). Therefore, the SAR requirement is deemed to be satisfied without test. **************************************** END ****************************************

Declaration Letter Related FCC ID: 2BU88LD1430RF Justification statement stating that all measurements were performed radiated and therefore additional antenna gain documentation is not required. See Internal photos for details of the antenna. By: __________________________ _______Erick Liu_______ (Signature) (Print name) Title: _____Certification Engineer_ Company: Intertek Testing Services (Shanghai FTZ) Co., Ltd.

Zafferano America LLC RF TEST Report Report Type: FCC Part 15.231 Test Report Model: LD1430RF REPORT NUMBER: 2601B1229SHA-001 ISSUE DATE: April 24, 2026 DOCUMENT CONTROL NUMBER: TTRF15.231_V1 © 2018 Intertek Intertek Testing Services (Shanghai FTZ) Co., Ltd Building No.86, 1198 Qinzhou Road (North) Caohejing Development Zone Shanghai 200233, China Telephone: 86 21 6127 8200 www.intertek.com TEST REPORT This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. TTRF15.231_V1 © 2018 Intertek Page 2 of 26 Report no.: 2601B1229SHA-001 Applicant : Zafferano America LLC 301 Penhorn Ave, Ste 5, Secaucus NJ 07094 Manufacturer : Qingdao Bozu International Trading Co.,Ltd No 166, Taoyuanhe 2nd Road, Huanxiu Street, Jimo Distrlct 266201, Qingdao, CHINA FCC ID : 2BU88LD1430RF SUMMARY: The equipment complies with the requirements according to the following standard(s) or Specification: 47CFR Part 15 (2024): Radio Frequency Devices (Subpart C) ANSI C63.10a (2024): American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices PREPARED BY: REVIEWED BY: Erick Liu Wakeyou Wang Project Engineer Reviewer Report No.: 2601B1229SHA-001 TEST REPORT TTRF15.231_V1 © 2018 Intertek Page 3 of 26 Content REVISION HISTORY................................................................................................................................................ 4 MEASUREMENT RESULT SUMMARY ..................................................................................................................... 5 1 GENERAL INFORMATION ............................................................................................................................. 6 1.1 DESCRIPTION OF EQUIPMENT UNDER TEST (EUT) ................................................................................................ 6 1.2 TECHNICAL SPECIFICATION ................................................................................................................................ 6 1.3 DESCRIPTION OF TEST FACILITY .......................................................................................................................... 7 2 TEST SPECIFICATIONS ................................................................................................................................... 8 2.1 STANDARDS OR SPECIFICATION .......................................................................................................................... 8 2.2 MODE OF OPERATION DURING THE TEST .............................................................................................................. 8 2.3 TEST SOFTWARE LIST ....................................................................................................................................... 8 2.4 TEST PERIPHERALS LIST..................................................................................................................................... 8 2.5 TEST ENVIRONMENT CONDITION: ....................................................................................................................... 8 2.6 INSTRUMENT LIST ........................................................................................................................................... 9 2.7 MEASUREMENT UNCERTAINTY ......................................................................................................................... 10 3 FUNDAMENTAL & SPURIOUS EMISSION & RESTRICT BAND RADIATED EMISSION ...................................... 11 3.1 LIMIT ......................................................................................................................................................... 11 3.2 MEASUREMENT PROCEDURE .......................................................................................................................... 12 3.3 TEST CONFIGURATION ................................................................................................................................... 13 3.4 TEST RESULTS OF RADIATED EMISSIONS ............................................................................................................ 15 4 POWER LINE CONDUCTED EMISSION ......................................................................................................... 19 4.1 LIMIT ......................................................................................................................................................... 19 4.2 TEST CONFIGURATION ................................................................................................................................... 19 4.3 MEASUREMENT PROCEDURE .......................................................................................................................... 20 4.4 TEST RESULTS OF POWER LINE CONDUCTED EMISSION .......................................................................................... 21 5 EMISSION BANDWIDTH ............................................................................................................................. 22 5.1 TEST CONFIGURATION ..........................................................................…

Text truncated - open the document above for the full version.

Page 1 of 3 Test Setup Page 2 of 3 Radiated Emission 30MHz-1GHz Page 3 of 3 Above 1GHz