2BUR7-3703TOY SERIES

72<6(5,(6 Installing the battery: Open the battery compartment andinsert 2 AA batteries with the correct polarity. Close the battery cover and tighten the fixing screws! This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s a uthority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in acco rdance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment d oes cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This device and its antenna(s) must not be co-located or operation in conjunction with any other a ntenna or transmitter. Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirement in portable exposure condition without restriction. Installing the battery: Open the battery compartment andinsert 2 AA batteries with the correct polarity. Close the battery cover and tighten the fixing screws! This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s a uthority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in acco rdance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference w ill not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This device and its antenna(s) must not be co-located or operation in conjunction with any other a ntenna or transmitter. Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirement in portable exposure condition without restriction. 72<6(5,(6

SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY FLOOR 3, NO. 4 XINXING ROAD, XINXIANG COMMUNITY, GUANGYI STREET, CHENGHAI DISTRICT, SHANTOU CITY, GUANGDONG PROVINCE, China Attestation Statements Not Covered Entity Applicant & Not Covered Equipment To: Federal Communications Commission Date: Mar. 18, 26 7435 Oakland Mills Road, Columbia, MD 21046, USA Ref: Information Required by Section 2.911(d)(5)(i) & (ii) FCC ID: 2BUR7-3703 SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List, established pursuant to § 1.50002 of reference chapter, as an entity producing “covered” communication equipment. The equipment for which authorization is sought is not “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List that prohibited from receiving an equipment authorization pursuant to section § 2.903 of the FCC rules. Sincerely yours, Applicant Signature Printed Name: Huang Junfan Title: Manager SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY FLOOR 3, NO. 4 XINXING ROAD, XINXIANG COMMUNITY, GUANGYI STREET, CHENGHAI DISTRICT, SHANTOU CITY, GUANGDONG PROVINCE, China Address: FLOOR 3, NO. 4 XINXING ROAD, XINXIANG COMMUNITY, GUANGYI STREET, CHENGHAI DISTRICT, SHANTOU CITY, GUANGDONG PROVINCE, China Tel.: 15875491777 Email: [email protected]

SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY FLOOR 3, NO. 4 XINXING ROAD, XINXIANG COMMUNITY, GUANGYI STREET, CHENGHAI DISTRICT, SHANTOU CITY, GUANGDONG PROVINCE, China 1 | P a g e Attestation Statements To: Federal Communications Commission Date: Mar. 18, 26 7435 Oakland Mills Road, Columbia, MD 21046, USA Subject: Attestation of Compliance with FCC Covered List Software Requirements FCC ID: 2BUR7-3703 Product Name: TOY SERIES This letter serves as an attestation that the equipment identified above ☐ is / ☒ is not (select one) "covered" software as defined under the Federal Communications Commission (FCC) Covered List requirements, as outlined in FCC 22-84 and KDB 986446. Specifically, the undersigned certifies that the equipment for which authorization is sought: 1. Does not contain cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors, assignees, parents, subsidiaries, affiliates, or any entity that has rebranded or relabeled software produced by the aforementioned entities. 2. Does not have the capability to store, run, or deliver any software identified on the FCC Covered List, including but not limited to cybersecurity and anti-virus software. To support this attestation, the appendix evaluation documentation has been prepared and is included in the certification filing. This attestation is based on a thorough evaluation of the device's design, functionality, and software environment. The undersigned affirms that the information provided is accurate and complete to the best of their knowledge. Sincerely yours, Applicant Signature Printed Name: Huang Junfan Title: Manager Address: FLOOR 3, NO. 4 XINXING ROAD, XINXIANG COMMUNITY, GUANGYI STREET, CHENGHAI DISTRICT, SHANTOU CITY, GUANGDONG PROVINCE, China Tel.: 15875491777 Email: [email protected] SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY FLOOR 3, NO. 4 XINXING ROAD, XINXIANG COMMUNITY, GUANGYI STREET, CHENGHAI DISTRICT, SHANTOU CITY, GUANGDONG PROVINCE, China 2 | P a g e Evaluation regarding to the Covered List Software: Compliance Methodology Evaluation Process Results Device is Inherent compliance ☒ The Chipset(s) used is limited to run the Cybersecurity or anti-virus software. Compliance ☒ The Memory used is limited to run the Cybersecurity or anti-virus software. Compliance ☒ There is storage capacity limitation for store or install the Cybersecurity or anti-virus software. Compliance ☒ Operating system used is limited to run, install or deliver the Cybersecurity or anti-virus software. Compliance Device is not Inherent compliance ☐ Evaluation Based on Software Bill of Materials (SBoM) See attached “SBoM“ Note:The SBoM content is limited to the scope of covered list software (e.g. antivirus and cybersecurity software). ☐ Evaluation Based on Scan for Software on the device ☐ Evaluation Based on Filesystem scan ☐ Evaluation Based on Running software check

The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. 48_[model] US_Agent_2.911(d)(7) - U, V05 SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Date: Mar. 18, 26 U.S. Agent Designation SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2BUR7-3703) Name and company of U.S. agent: GLOCERTS TECHNOLOGY INC Physical U.S. address of agent: 19784 SUNKISSED RIDGE DR, RIVERSIDE, CA 92507 FRN of U.S. agent: 0036339737 Email address of U.S. agent: [email protected] Telephone of U.S.agent: (626) 588-8039 GLOCERTS TECHNOLOGY INC acknowledges their obligation to accept service of process on behalf of SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY. SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY with the FRN [0037971835] accepts its obligation to maintain an agent for service of process in the United States for no less than 1 year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Signature Huang Junfan Huiying Fan Manager Director SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY GLOCERTS TECHNOLOGY INC

SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY FLOOR 3, NO. 4 XINXING ROAD, XINXIANG COMMUNITY, GUANGYI STREET, CHENGHAI DISTRICT, SHANTOU CITY, GUANGDONG PROVINCE, China Date: 2026/3/16 Dear Sir/Madam, We, SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY, Hereby declares the following statement, PCB board, circuit, structure and internal of these model(s) are the same, Only model name is different for these model: Product name: TOY SERIES FCC ID: 2BUR7-3703 Model no.: 3650, 3651, 3652, 3653, 3654, 3655, 3656, 3657, 3658, 3659, 3660, 3661, 3662, 3663, 3664, 3665, 3666, 3667, 3668, 3669, 3670, 3671, 3672, 3673, 3674, 3675, 3676, 3677, 3678, 3679, 3680, 3681, 3682, 3683, 3684, 3685, 3686, 3687, 3688, 3689, 3690, 3691, 3692, 3693, 3694, 3695, 3696, 3697, 3698, 3699, 3700, 3701, 3702, 3704, 3705, 3706, 3707, 3708, 3709, 3710, 3711, 3712, 3713, 3714, 3715, 3716, 3717, 3718, 3719, 3720, 3721, 3722, 3723, 3724, 3725, 3726, 3727, 3728, 3729, 3730, 3731, 3732, 3733, 3734, 3735, 3736, 3737, 3738, 3739, 3740, 3741, 3742, 3743, 3744, 3745, 3746, 3747, 3748, 3749, 3750 Sincerely, Name/Title： Huang Junfan / Manager Company: SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY Address: FLOOR 3, NO. 4 XINXING ROAD, XINXIANG COMMUNITY, GUANGYI STREET, CHENGHAI DISTRICT, SHANTOU CITY, GUANGDONG PROVINCE, China Phone: 15875491777 Fax: N/A E-Mail: [email protected]

SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY FLOOR 3, NO. 4 XINXING ROAD, XINXIANG COMMUNITY, GUANGYI STREET, CHENGHAI DISTRICT, SHANTOU CITY, GUANGDONG PROVINCE, China March 18, 2026 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request for: FCC ID: 2BUR7-3703 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request permanent confidential treatment of the exhibits accompanying this certification application as outlined below : ⎯ Block Diagram ⎯ Schematics ⎯ Operational Description The above exhibits contain trade secrets and/or proprietary information that are not publicly available and materials that the Applicant has spent considerable efforts in developing. Public disclosure of these may be harmful to the Applicant and give an unfair advantage to competitors on the market. Sincerely, Title: Manager Address: FLOOR 3, NO. 4 XINXING ROAD, XINXIANG COMMUNITY, GUANGYI STREET, CHENGHAI DISTRICT, SHANTOU CITY, GUANGDONG PROVINCE, China Tel.: 15875491777 Email: [email protected]

SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY FLOOR 3, NO. 4 XINXING ROAD, XINXIANG COMMUNITY, GUANGYI STREET, CHENGHAI DISTRICT, SHANTOU CITY, GUANGDONG PROVINCE, China March 18, 2026 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization for FCC ID: 2BUR7-3703 I, the undersigned, hereby authorize Attestation of Global Compliance (Shenzhen) Co., Ltd. to act on our behalf in all matters relating to this application for equipment certification. Any act carried out by Attestation of Global Compliance (Shenzhen) Co., Ltd. shall have the same effect as our own and I acknowledge that all responsibility for complying with the terms and conditions of certification, as specified by DERYCOM CERTIFICATION SERVICES, INC., still resides with SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY. We certify that we are not subject to a denial of federal benefits that includes FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862, and that no party to the application, as defined in 47 CFR §1.2002(b), is subject to a denial of federal benefits that includes FCC benefits pursuant to that section. Sincerely, Huang Junfan Manager Tel: 15875491777 Fax: N/A Email: [email protected]

Report No.: AGC10211260306AP02 Page 1 of 3 EXTERNAL PHOTOS External Photo 1 External Photo 2 Report No.: AGC10211260306AP02 Page 2 of 3 External Photo 3 External Photo 4 Report No.: AGC10211260306AP02 Page 3 of 3 External Photo 5 External Photo 6 ****************************************End of Report*************************************

The size of the label is 30mm*25mm with White forecolor. The size of the logo is 5mm*5mm. Label Location FCC ID: 2BUR7-3703

Report No.: AGC10211260306AP02 Page 1 of 3 INTERNAL PHOTOS Internal Photo 1 Internal Photo 2 Report No.: AGC10211260306AP02 Page 2 of 3 Internal Photo 3 Internal Photo 4 SRD antenna Report No.: AGC10211260306AP02 Page 3 of 3 Internal Photo 5 ****************************************End of Report*************************************

Page 1 of 10 RF Exposure Report Report No.: AGC10211260306FH01 FCC ID : 2BUR7-3703 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : TOY SERIES BRAND NAME : N/A MODEL NAME : Refer to page 4 of this report APPLICANT : SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY DATE OF ISSUE : Mar. 17, 2026 STANDARD(S) : FCC KDB 447498 D01 V06 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC10211260306FH01 Page 2 of 10 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Mar. 17, 2026 Valid Initial Release Report No.: AGC10211260306FH01 Page 3 of 10 Table of Contents 1. General Information ........................................................................................................................................ 4 2. Product Information ........................................................................................................................................ 5 2.1 Product Technical Description ................................................................................................................... 5 3. Test Environment ............................................................................................................................................ 6 3.1 Address Of The Test Laboratory ............................................................................................................... 6 3.2 Test Facility ................................................................................................................................................ 6 3.3 Environmental Conditions ......................................................................................................................... 7 4. Portable Device Evaluation Method and Limit ............................................................................................. 8 5. Measurement Results ..................................................................................................................................... 9 Report No.: AGC10211260306FH01 Page 4 of 10 1. General Information Applicant SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY Address FLOOR 3, NO. 4 XINXING ROAD, XINXIANG COMMUNITY, GUANGYI STREET, CHENGHAI DISTRICT, SHANTOU CITY, GUANGDONG PROVINCE, China Manufacturer SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY Address FLOOR 3, NO. 4 XINXING ROAD, XINXIANG COMMUNITY, GUANGYI STREET, CHENGHAI DISTRICT, SHANTOU CITY, GUANGDONG PROVINCE, China Product Designation TOY SERIES Brand Name N/A Test Model 3703 Series Model(s) Refer to page 6 of this report Difference Description All the same except for the model name Date of receipt of test item Mar. 09, 2026 Date of Test Mar. 09, 2026~ Mar. 17, 2026 Deviation from Standard Shantou Meiyida Intelligent Technology Co., Ltd Condition of Test Sample Normal Test Result Pass Test Report Form No AGCER-FCC-RF Exposure-V1 Note: The test results of this report relate only to the tested sample identified in this report. Prepared By Cool Cheng (Project Engineer) Mar. 17, 2026 Reviewed By Bibo Zhang (Reviewer) Mar. 17, 2026 Approved By Angela Li (Authorized Officer) Mar. 17, 2026 Report No.: AGC10211260306FH01 Page 5 of 10 2. Product Information 2.1 Product Technical Description Frequency Band (Operating) Short Range Device: 2410MHz-2470MHz Hardware Version V1.0 Software Version V1.0 Modulation Type GFSK Device Category Portable (<20cm separation) Mobile (>20cm separation) Others: Antenna Diversity Single antenna Multiple antennas Tx diversity Rx diversity Tx/Rx diversity Antenna Designation PCB Antenna Antenna Gain 0.59dBi Minimum Assessment Distance 5mm Evaluation Applied MPE Evaluation SAR Evaluation Series Model(s) 3650, 3651, 3652, 3653, 3654, 3655, 3656, 3657, 3658, 3659, 3660, 3661, 3662, 3663, 3664, 3665, 3666, 3667, 3668, 3669, 3670, 3671, 3672, 3673, 3674, 3675, 3676, 3677, 3678, 3679, 3680, 3681, 3682, 3683, 3684, 3685, 3686, 3687, 3688, 3689, 3690, 3691, 3692, 3693, 3694, 3695, 3696, 3697, 3698, 3699, 3700, 3701, 3702, 3704, 3705, 3706, 3707, 3708, 3709, 3710, 3711, 3712, 3713, 3714, 3715, 3716, 3717, 3718, 3719, 3720, 3721, 3722, 3723, 3724, 3725, 3726, 3727, 3728, 3729, 3730, 3731, 3732, 3733, 3734, 3735, 3736, 3737, 3738, 3739, 3740, 3741, 3742, 3743, 3744, 3745, 3746, 3747, 3748, 3749, 3750 Report No.: AGC10211260306FH01 Page 6 of 10 3. Test Environment 3.1 Address Of The Test Laboratory Laboratory: Attestation of Global Compliance (Shenzhen) Co., Ltd. Address: 1-2/F, Building 19, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China 3.2 Test Facility The test facility is recognized, certified, or accredited by the following organizations: CNAS-Lab Code: L5488 Attestation of Global Compliance (Shenzhen) Co., Ltd. has been assessed and proved to follow CNAS-CL01 Accreditation Criteria for Testing and Calibration Laboratories (identical to ISO/IEC17025: 2017 General Requirements for the Competence of Testing and Calibration Laboratories.) A2LA-Lab Cert. No.: 5054.02 Attestation of Global Compliance (Shenzhen) Co., Ltd. EMC Laboratory has been accredited by A2LA for technical competence in the field of electrical testing, and proved to follow ISO/IEC 17025: 2017 General Requirements for the Competence of Testing and Calibration Laboratories and any additional program requirements in the identified field of testing. FCC-Registration No.: 975832 Attestation of Global Compliance (Shenzhen) Co., Ltd. EMC Laboratory has been registered and fully described in a report filed with the FCC (Federal Communications Commission). The acceptance letter from the FCC is maintained in our files with Registration 975832. IC-Registration No.: 24842(CAB identifier: CN0063) Attestation of Global Compliance (Shenzhen) Co., Ltd. EMC Laboratory has been registered and fully described in a report filed with the Certification and Engineering Bureau of Industry Canada. The a…

Text truncated - open the document above for the full version.

天線規格承認書 Acceptanceofantennaspecifications 制造商： Manufacturer ： 規格 ： Specifications： 產品料號： PartNO.: 汕头市龙湖区科马电子加工场 ShantouLonghuDistrictKomaElectronicProcessing Factory 2.4G天線全長40MM白色 17芯*0.1*1.6PVC 地址: 汕头市龙湖区新津街道金泰街22号二楼 No.22,JintaiStreet,XinjinSub-district,LonghuDistrict, ShantouCity,SecondFloor Address： 图示： Ø1.6 ProductSpecification A.Electrical Characteristics Frequency 2400MHz ~2500MHz VSWR <3.0 Efficiency >20% Impedance 50 Ohm Gain 0.59 DBi Polarization mode: linear polarization B.Material & Mechanical Characteristics Material of Radiator Cu Cable Type 1.4 white Connector Type : NO Dimension C.Environmental Operation Temperature - 30 °C ~ + 80 °C Storage Temperature - 30 °C ~ + 85 °C Test Equipment& Conditions 1.NetworkAnalyzers: Agilent8753D5071B 2. CommunicationsTest Set: AgilentE5515C 3. 3D ChamberTest System Effiency&Gain Freq (MHz) Effi (%) Gain (dBi) 2400 23.660.47 2410 23.190.38 2420 23.030.49 2430 22.410.42 2440 21.670.45 2450 20.240.52 2460 20.610.51 2470 21.410.59 2480 23.890.56 2490 26.460.53 2500 25.730.46 RadiationPattern 70 70 5.00 2450.000MHzE1 5.00 2450.000MHzE2 5.00 2500.000MHz 2500.000MHzH 2.2 1.2 -O.3 -1.8 -3.8 -5.8 -7.8 2500.000MHzE1 2500.000MHzE2 70 g 70 70 9 9 g

Page 1 of 47 FCC Test Report Report No.: AGC10211260306FR01 FCC ID : 2BUR7-3703 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : TOY SERIES BRAND NAME : N/A MODEL NAME : Refer to page 5 of this report APPLICANT : SHANTOU CITY CHENGHAI DISTRICT FANGZUAN TOYS FACTORY DATE OF ISSUE : Mar. 17, 2026 STANDARD(S) : FCC Part 15 Subpart C §15.247 REPORT VERSION : V1.0 Attestation Of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC10211260306FR01 Page 2 of 47 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Mar. 17, 2026 Valid Initial Release Report No.: AGC10211260306FR01 Page 3 of 47 Table of Contents 1. General Information ........................................................................................................................................ 5 2. Product Information ........................................................................................................................................ 6 2.1 Product Technical Description ................................................................................................................... 6 2.2 Test Frequency List ................................................................................................................................... 6 2.3 Related Submittal(S) / Grant (S) ............................................................................................................... 7 2.4 Test Methodology ...................................................................................................................................... 7 2.5 Special Accessories .................................................................................................................................. 7 2.6 Equipment Modifications ........................................................................................................................... 7 2.7 Antenna Requirement................................................................................................................................ 7 3. Test Environment ............................................................................................................................................ 8 3.1 Address of the Test Laboratory ................................................................................................................. 8 3.2 Test Facility ................................................................................................................................................ 8 3.3 Environmental Conditions ......................................................................................................................... 9 3.4 Measurement Uncertainty ......................................................................................................................... 9 3.5 List of Equipment Use ............................................................................................................................. 10 4.System Test Configuration ............................................................................................................................ 12 4.1 EUT Configuration ................................................................................................................................... 12 4.2 EUT Exercise ........................................................................................................................................... 12 4.3 Configuration of Tested System .............................................................................................................. 12 4.4 Equipment Used In Tested System ........................................................................................................ 12 4.5 Summary of Test Results ........................................................................................................................ 13 5. Description of Test Modes ........................................................................................................................... 14 6. Duty Cycle Measurement ............................................................................................................................. 15 7. RF Output Power Measurement .................................................................................................................. 17 7.1 Provisions Applicable .............................................................................................................................. 17 7.2 Measurement Procedure ......................................................................................................................... 17 7.3 Measurement Setup (Block Diagram of Configuration) .......................................................................... 17 7.4 Measurement Result ............................................................................................................................... 18 8. 6dB Bandwidth Measurement ...................................................................................................................... 20 8.1 Provisions Applicable .............................................................................................................................. 20 8.2 Measurement Procedure ......................................................................................................................... 20 8.3 Measurement Setup (Block Diagram of Configuration) .......................................................................... 20 8.4 Measurement Results ............................................................................................................................. 21 9. Power Spectral Density Measurement ........................................................................................................ 24 9.1 Provisions Applicable ...........................................................................................................…

Text truncated - open the document above for the full version.

Report No.: AGC10211260306AP01 Page 1 of 1 TEST SETUP PHOTOS RADIATED EMISSION TEST SETUP BELOW 1GHz RADIATED EMISSION TEST SETUP ABOVE 1GHz ****************************************End of Report*************************************