Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
1 3 2 3 ( 45.5) (13.0) PROPRIETARY AND HIGHLY CONFIDENTIAL INSPECTION CRITERIA: TOP HOUSING SUB-ASSEMBLY MUST BE PRESS-FIT INTO THE1. CORRECT WELLS IN THE BOTTOM HOUSING, WITHOUT ANY SUPERFICIAL SCRATCHES OR MARRING. THE TOP HOUSING SUB-ASSEMBLY MUST BE INSTALLED SO THAT2. THERE IS A STRAIGHT LINE MINIMAL GAP WITH THE BOTTOM HOUSING SUB-ASSEMBLY. APPLY 0.25CC OF LOCTITE EA9460 EPOXY ADHESIVE (ITEM 2)3. ON EACH OF FOUR TAB FEATURES BEFORE ASSEMBLY. REVISIONS ZONEREV.DESCRIPTIONDATEAPPROVED ARELEASE FOR APPROVALS04/03/2026BC ITEM NO.PART NUMBERDESCRIPTIONQTY. 1ASM-0005-000-A TOP HOUSING - STANDARD CAPACITY - STAINLESS STEEL - BLUE LENS 1 2MEC-0039-000-ALOCTITE EA94601 3ASM-0019-000-A BOTTOM HOUSING - STANDARD CAPACITY - STAINLESS - STAINLESS SWITCH 1 MINIMIC ASSEMBLY - STANDARD CAPACITY - STAINLESS - BLUE LENS A DO NOT SCALE DRAWING ASM-0105-000-A SHEET 1 OF 1 11.18.25 CB UNLESS OTHERWISE SPECIFIED: SCALE: 2:1 WEIGHT: REV B SIZE TITLE: NAME DATE COMMENTS: Q.A. MFG APPR. ENG APPR. CHECKED DRAWN FINISH MATERIAL INTERPRET GEOMETRIC TOLERANCING PER: DIMENSIONS ARE IN MILLIMETERS TOLERANCES: FRACTIONAL ANGULAR: MACH BEND TWO PLACE DECIMAL THREE PLACE DECIMAL APPLICATION USED ON NEXT ASSY PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF ANALOG DEVICES, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF ANALOG DEVICES, INC. IS PROHIBITED. AA BB 4 4 3 3 2 2 1 1 DWG. / PART # 1 3 2 3 ( 45.5) (16.0) PROPRIETARY AND HIGHLY CONFIDENTIAL INSPECTION CRITERIA: TOP HOUSING SUB-ASSEMBLY MUST BE PRESS-FIT INTO THE1. CORRECT WELLS IN THE BOTTOM HOUSING, WITHOUT ANY SUPERFICIAL SCRATCHES OR MARRING. THE TOP HOUSING SUB-ASSEMBLY MUST BE INSTALLED SO THAT2. THERE IS A STRAIGHT LINE MINIMAL GAP WITH THE BOTTOM HOUSING SUB-ASSEMBLY. APPLY 0.25CC OF LOCTITE EA9460 EPOXY ADHESIVE (ITEM 2)3. ON EACH OF FOURTAB FEATURES BEFORE ASSEMBLY. REVISIONS ZONEREV.DESCRIPTIONDATEAPPROVED ARELEASE FOR APPROVALS04/03/2026BC ITEM NO.PART NUMBERDESCRIPTIONQTY. 1ASM-0001-000-A TOP HOUSING - EXTENDED CAPACITY - STAINLESS STEEL - BLUE LENS 1 2MEC-0039-000-ALOCTITE EA94601 3ASM-0015-000-A BOTTOM HOUSING - EXTENDED CAPACITY - STAINLESS - STAINLESS SWITCH 1 MINIMIC ASSEMBLY - EXTENDED CAPACITY - STAINLESS - BLUE LENS A DO NOT SCALE DRAWING ASM-0101-000-A SHEET 1 OF 1 11.18.25 CB UNLESS OTHERWISE SPECIFIED: SCALE: 2:1 WEIGHT: REV B SIZE TITLE: NAME DATE COMMENTS: Q.A. MFG APPR. ENG APPR. CHECKED DRAWN FINISH MATERIAL INTERPRET GEOMETRIC TOLERANCING PER: DIMENSIONS ARE IN MILLIMETERS TOLERANCES: FRACTIONAL ANGULAR: MACH BEND TWO PLACE DECIMAL THREE PLACE DECIMAL APPLICATION USED ON NEXT ASSY PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF ANALOG DEVICES, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF ANALOG DEVICES, INC. IS PROHIBITED. AA BB 4 4 3 3 2 2 1 1 DWG. / PART # 8.87 8.87 +D 7.51+D 49.69 A A 1.00-D (2X) M2 X 0.40MM (4X) 10.20 -D 19.02 (2X) 24.00 9.51 (2X) 32.33° 12.00 (2X) C C B B B 41.40 43.39 35.50 3.39+D 1.70 +D 33.50 2.72 0.30 41.41 SECTION A-A SCALE 3 : 1 .005 A NOTES: ALL DIMENSIONS ARE IN MILLIMETERS.1. UNLESS OTHERWISE NOTED, ALL TOLERANCES PER DIN ISO 2768-1 FINE.2. MATERIAL: STAINLESS STEEL 316L.3. FINISH: UNLESS OTHERWISE SPECIFIED, MATTE SATIN.4. GATE: LOCATION NOT TO BE VISIBLE ON OUTSIDE SURFACES AND TO BE APPROVED BEFORE TOOLING.5. NO WARP, SPLAY, BLUSH, SINK OR FLOW MARKS ALLOWED.6. VOLUME: 3.25 CC.7. LIMITED DIMENSION DRAWING. USE ASSOCIATED CAD FILE "MEC-0040-000-A.STEP" FOR GEOMETRIC REFERENCE.8. ALL MODEL GEOMETRY IS CONSIDERED BASIC: .005AB APPLIES TO ALL SURFACES.9. ALL LASER ETCH: FILL IN GEOMETRY WITH LASER ETCH.10. LASER ETCH FONT: ARIAL, 5PT MINIMUM.11. PROPRIETARY AND HIGHLY CONFIDENTIAL REVISIONS ZONEREV.DESCRIPTIONDATEAPPROVED ARELEASE FOR APPROVALS04/03/2026BC BOTTOM HOUSING - STAINLESS STEEL A DO NOT SCALE DRAWING MEC-0040-000-A SHEET 1 OF 3 11.21.24 CB UNLESS OTHERWISE SPECIFIED: SCALE: 2:1 WEIGHT: REV B SIZE TITLE: NAME DATE COMMENTS: Q.A. MFG APPR. ENG APPR. CHECKED DRAWN FINISH MATERIAL INTERPRET GEOMETRIC TOLERANCING PER: DIMENSIONS ARE IN MILLIMETERS TOLERANCES: FRACTIONAL ANGULAR: MACH BEND TWO PLACE DECIMAL THREE PLACE DECIMAL APPLICATION USED ON NEXT ASSY PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF ANALOG DEVICES, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF ANALOG DEVICES, INC. IS PROHIBITED. DWG. / PART # AA BB 4 4 3 3 2 2 1 1 3.20 0.50 38.89 (2X) 5.00 0.23 R0.50 SECTION B-B 1.60+D 1.43 1.55 0.45 SECTION C-C TYP X2 LITEPIPE HOLES BOTTOM HOUSING - STAINLESS STEEL A DO NOT SCALE DRAWING MEC-0040-000-A SHEET 2 OF 3 UNLESS OTHERWISE SPECIFIED: SCALE: 3:1 WEIGHT: REV B SIZE TITLE: NAME DATE COMMENTS: Q.A. MFG APPR. ENG APPR. CHECKED DRAWN FINISH MATERIAL INTERPRET GEOMETRIC TOLERANCING PER: DIMENSIONS ARE IN INCHES TOLERANCES: FRACTIONAL ANGULAR: MACH BEND TWO PLACE DECIMAL THREE PLACE DECIMAL APPLICATION USED ON NEXT ASSY PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF <INSERT COMPANY NAME HERE>. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF <INSERT COMPANY NAME HERE> IS PROHIBITED. DWG. / PART # AA BB 4 4 3 3 2 2 1 1 11 LASER ETCH 10 BOTTOM HOUSING - STAINLESS STEEL A DO NOT SCALE DRAWING MEC-0040-000-A SHEET 3 OF 3 UNLESS OTHERWISE SPECIFIED: SCALE: 4:1 WEIGHT: REV B SIZE TITLE: NAME DATE COMMENTS: Q.A. MFG APPR. ENG APPR. CHECKED DRAWN FINISH MATERIAL INTERPRET GEOMETRIC TOLERANCING PER: DIMENSIONS ARE IN INCHES TOLERANCES: FRACTIONAL ANGULAR: MACH BEND TWO PLACE DECIMAL THREE PLACE DECIMAL APPLICATION USED ON NEXT ASSY PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF <INSERT COMPANY NAME HERE>. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF <INSERT COMPANY NAME HERE> IS PROHIBITED. DWG. / PART # AA BB 4 4 3 3 2 2 1…
Text truncated - open the document above for the full version.
2.45 GHz High Gain SMD Chip Antenna, AEC-Q200 Qualified P/N 2450AT45A100E-AEC Detail Specification:Page 1 of 11 Mechanical Specifications Inmm No L ±± 1 W ±± 2 T a ±± Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. https://www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 2021 Johanson Technology, Inc. All Rights Reserved e.g. 2450AT45A100S-AEC Packing Style T & R 100% Tin 2450AT45A100-EB3SMA (Page 8) 2450AT45A100-EB2SMA (Page 5) 2450AT45A100-EB1SMA (Page 2) Mounting Considerations 2: "Horizontal Orientation Type A" (Pages 5) 0.012 Feeding Point Function NC2.000.20 0.20 Evaluation Boards (1-port SMA antenna test boards, pre-tuned) 0.0080.079 Part Number Explanation Suffix = S Suffix = E Suffix = None Bulk (loose pcs.) P/N Suffix 2400 - 2500 e.g. 2450AT45A100E-AEC e.g. 2450AT45A100(E or S)-AEC 2450AT45A100E-AEC 1,000 -40°C to +125°C 3W max. (CW) Impedance50 Ω Mounting Considerations 1: "Vertical Orientation" (Page 2) 2.2 dBi typ. (XZ-V) 1.5 dBi typ. (XZ-V) 1.3 dBi typ. (XZ-V) Humidity 45 - 75% RH 18 months max. High Frequency Ceramic Solutions Terminal Configuration Ver 1.2 4/5/2021 0.0200.50 0.3740.008 0.0471.20+.004/-.008+0.1/-0.2 9.50 0.30 Mounting Considerations 3: "Horizontal Orientation Type B" (Pages 8) Let us help you with the antenna design, optimization, and tuning! https://www.johansontechnology.com/ask-a-question General Specifications Part Number Frequency Range (MHz) Input Power Operating Temp Reel Quantity (pcs/reel) Recommended Storage Conditions and Period for unused Product on T&R Peak Gain Based on Orientation +5 to +35°C 1 2 L W a T Top Bottom 2.45 GHz High Gain SMD Chip Antenna, AEC-Q200 Qualified P/N 2450AT45A100E-AEC Detail Specification:Page 2 of 11 Mount these devices with brown mark facing up. *Line width should be designed to provide 50Ω impedance matching characteristics. Units in mm Orderable Evaluation board: p/n: 2450AT45A100-EB1SMA Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. https://www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 2021 Johanson Technology, Inc. All Rights Reserved "C" Dimension will depend on the width of the trace required for it to have a 50ohm characteristic impedance (i.e. coplanar waveguide theory) Ver 1.2 1.0 dBi typ. (XZ-V) Mounting Considerations 1: "Vertical Orientation" High Frequency Ceramic Solutions 4/5/2021 Typical Electrical Specs for "Vertical Orientation" (T=25°C) Frequency Range 2400 - 2500 MHz Peak Gain 2.2 dBi typ. (XZ-V) Return Loss 9.5 dB min. Average Gain ) ) 1.8 7.5 10.5 1.0 3.9nH 1.5pF * * GND GND Want the layout file of this? Send us a message at: https://www.johansontechnology.com/ask- a-question Let us help you design this antenna to your PCB and/or optimize your layout for best radiated performance. Send us a message by clicking on the link above. 20 ) ) No Ground or Metals underneath 4012 50Ω Feed Line GND GND 1.5pF 3.9nH Note: It is recommended that the designer leave available slots for a "pi" (or shunt-series-shunt) network. The antenna matching network values above are used when antenna is mounted on Johanson's evaluation board. The matching values on client's PCB will be different, go to: https://www.johansontechnology.com/tuningand see how to obtain the new values. If you need further help, contact our RF Applications Eng Team at: https://www.johansontechnology.com/ask-a-question C 2.45 GHz High Gain SMD Chip Antenna, AEC-Q200 Qualified P/N 2450AT45A100E-AEC Detail Specification:Page 3 of 11 Return Loss a) Without a Matching Circuit b) With a Matching Circuit Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. https://www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 2021 Johanson Technology, Inc. All Rights Reserved Ver 1.2 High Frequency Ceramic Solutions 4/5/2021 Typical Electrical Characteristics for "Vertical Orientation" (T=25°C) 2.45 GHz High Gain SMD Chip Antenna, AEC-Q200 Qualified P/N 2450AT45A100E-AEC Detail Specification:Page 4 of 11 Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. https://www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 2021 Johanson Technology, Inc. All Rights Reserved High Frequency Ceramic Solutions 4/5/2021 Typical Radiation Patterns for "Vertical Orientation" (T=25°C) Ver 1.2 ) ) ) XY-V/XY-H 180° 270° 0° 90° X Z Y XY-cut scanning direction XY cut @2.45GHz Vertical Horizontal XZ-V/XZ-H YZ-V/YZ-H 180° 270° 0° 90° X Z Y XZ-cut scanning direction 180° 270° 0° 90° X Z Y YZ-cut scanning direction XZ cut @2.45GHz Vertical Horizontal YZ cut @2.45GHz Vertical Horizontal 2.45 GHz High Gain SMD Chip Antenna, AEC-Q200 Qualified P/N 2450AT45A100E-AEC Detail Specification:Page 5 of 11 Mount these devices with brown mark facing up. *Line width should be designed to provide 50Ω impedance matching characteristics. Units in mm Orderable Evaluation board: p/n: 2450AT45A100-EB2SMA Johanson Technology, Inc. reserves the right to make design changes without notice. All sales are subject to Johanson Technology, Inc. terms and conditions. https://www.johansontechnology.com 4001 Calle Tecate • Camarillo, CA 93012 • TEL 805.389.1166 FAX 805.389.1821 2021 Johanson Technology, Inc. All Rights Reserved Ver 1.2 Mounting Considerations 2: "Horizontal Orientation Type A" "C" Dimension will depend on the width of the trace required for it to have a 50ohm characteristic impedance (i.e. coplanar waveguide theory) High Frequency Ceramic Solutions 4/5/2021 Return Loss9.5…
Text truncated - open the document above for the full version.
4840 Winchester Boulevard., Suite #5 Frederick, Maryland 21703 (USA) (301) 216-1500 [email protected] Page 1 of 1 April 21, 2026 Test Letter #: 19558-02 Rev 0 (reference DTS report #19558-01) Applicant: Analog Devices, Inc. Exempt RF Device: miniMic FCC ID: 2BUXT-MM1 Category: General Population, Mobile EUT Summary: The miniMic (Standard) and miniMic (Extended) are categorically excluded from SAR testing. The EUT peak power meets the average exemption limits. Stand-Alone, Time-Averaged Exclusion for FCC: Per FCC Rule Part §1.1307(b)(3)(i)(A): a single RF source is exempt from routine environmental evaluation for RF exposure compliance if the available maximum time-averaged power is no more than 1 mW, regardless of separation distance. EUT Transmitter Details: The EUT is a 2.4GHz BLE transmitter device. The intended separation distance is < 5 mm. Peak Conducted Output Power = -5.78 dBm Maximum Peak Antenna Gain = +2.20 dBi Tune-Up Tolerance: = ±1.0 dB Worst-Case EIRP: = -2.58 dBm (Peak) Calculations: EIRP = -5.78 + 2.20 + 1.0 = -2.58 dBm (Peak) mW = 10 (dBm/20) 10 (-2.58/20) = 0.5521 mW Exclusion Results for FCC: 0.5521 mW < 1 mW The EUT is exempt from the obligation to perform a routine environmental evaluation to demonstrate compliance with the RF exposure limits of FCC Rule Part §1.1310.
FCC CERTIFICATION TEST REPORT for the MINIMIC FCC ID: 2BUXT-MM1 WLL REPORT# 19558-01 REV 0 Prepared for: Analog Devices, Inc. 1 Analog Way Wilmington, Massachusetts 01887 Prepared By: Washington Laboratories, Ltd. 4840 Winchester Blvd. Suite 5 Frederick, Maryland 21703 Testing Certificate AT-1448 Certificates and reports shall not be reproduced except in full, without the written permission of Washington Laboratories, Ltd Analog Devices, Inc. miniMic FCC 15.247 Certification Test Report WLL Report 19558-01 Rev 0 Page 2 of 112 FCC Certification Test Report for the Analog Devices, Inc. miniMic FCC ID: 2BUXT-MM1 April 23, 2026 WLL Report# 19558-01 Rev 0 Prepared by: ___________________________ Ryan Mascaro RF Test Engineer Reviewed by: ____________________________ Steven D. Koster President Analog Devices, Inc. miniMic FCC 15.247 Certification Test Report WLL Report 19558-01 Rev 0 Page 3 of 112 Abstract This report has been prepared on behalf of Analog Devices, Inc. to support the attached Application for Equipment Authorization. The test report and application are submitted for a Digital Transmission System (DTS) Transmitter device under Part 15.247 of the FCC Rules and Regulations (current at the time of testing). This certification test report documents the test configuration and test results for the Analog Devices, Inc., miniMic. The information provided in this report, along with the results obtained, are only applicable to the item tested herein, documented as the EUT. Radiated testing above 30MHz was performed in the Free-space Anechoic Chamber Test-site (FACT) 3m chamber of Washington Laboratories, Ltd., located at: 4840 Winchester Boulevard, Suite 5., Frederick, MD 21703. Site description and site attenuation data have been placed on file with the FCC's Sampling and Measurements Branch at the FCC laboratory in Columbia, MD. Washington Laboratories has been accepted and designated by the FCC under Test Firm Number US3001. Washington Laboratories is approved by the ANSI National Accreditation Board (ANAB), as an independent test laboratory under ISO/IEC 17025:2017. Please refer to Certificate Number AT-1448. The Analog Devices, Inc., miniMic complies with the requirements for a Digital Transmission System (DTS) transmitter device under FCC Rule Part 15.247. Revision History Description of Change Date Rev 0 Initial Release April 23, 2026 Analog Devices, Inc. miniMic FCC 15.247 Certification Test Report WLL Report 19558-01 Rev 0 Page 4 of 112 Table of Contents Abstract ...................................................................................................................................................... iii Table of Contents ....................................................................................................................................... iv List of Tables .............................................................................................................................................. v List of Figures ............................................................................................................................................ vi 1 Introduction ..................................................................................................................................... 7 Compliance Statement ................................................................................................................ 7 Test Scope ................................................................................................................................... 7 Contract Information ................................................................................................................... 7 Test and Support Personnel ........................................................................................................ 7 Test Location .............................................................................................................................. 7 2 Equipment Under Test .................................................................................................................... 8 EUT Identification ...................................................................................................................... 8 EUT Description ......................................................................................................................... 9 Test Configuration and Algorithm ............................................................................................ 10 Customer Supplied Data or EUT Information .......................................................................... 11 Equipment Configuration.......................................................................................................... 11 3 Test Results ................................................................................................................................... 14 Deviations to the Test Standard ................................................................................................ 14 Testing Dates ............................................................................................................................ 14 Occupied Bandwidth, Digital Transmission System ................................................................ 15 Conducted Peak Output Power ................................................................................................. 20 Power Spectral Density ............................................................................................................. 25 Conducted Bandedge Testing ................................................................................................... 30 Conducted Unwanted Spurious Emissions ............................................................................... 33 Radiated Emissions ................................................................................................................... 46 AC Con…
Text truncated - open the document above for the full version.
Analog Devices, Inc. miniMic FCC 15.247 Certification Test Report WLL Report 19558-01 Rev 0 Page-57 of 112 Table 12: 3-meter Radiated Test Data, Center Channel, 1Mbps, 1GHz to 18GHz, miniMic Standard Frequency (MHz) Detector Meas (dBuV/m) Limit (dBuV/m) Delta (dB) Turn Table (deg) Antenna (cm) 2440.00 TX Peak 89.055 -- -- 200 Vert, 125 Avg -- -- -- 200 Vert, 125 4880.00 Peak 53.337 74 -20.663 200 Vert, 125 Avg 43.256 54 -10.744 200 Vert, 125 9047.00 Peak 59.481 74 -14.519 290 Horiz, 200 Avg 43.76 54 -10.240 290 Horiz, 200 9572.00 Peak 59.816 74 -14.184 290 Horiz, 200 Avg 44.191 54 -9.809 290 Horiz, 200 10809.00 Peak 64.333 74 -9.667 290 Horiz, 200 Avg 48.162 54 -5.838 290 Horiz, 200 12341.00 Peak 56.138 74 -17.862 200 Vert, 125 Avg 42.064 54 -11.936 200 Vert, 125 13474.00 Peak 56.823 74 -17.177 290 Horiz, 200 Avg 43.192 54 -10.808 290 Horiz, 200 17300.00 Peak 61.737 74 -12.263 290 Horiz, 200 Avg 47.731 54 -6.269 290 Horiz, 200 Analog Devices, Inc. miniMic FCC 15.247 Certification Test Report WLL Report 19558-01 Rev 0 Page-58 of 112 miniMic Standard, Center Channel, 1Mbps, Pre-scan and Final Data (Vertical), 1GHz to 12GHz miniMic Standard, Center Channel, 1Mbps, Pre-scan and Final Data (Horizontal), 1GHz to 12GHz Analog Devices, Inc. miniMic FCC 15.247 Certification Test Report WLL Report 19558-01 Rev 0 Page-59 of 112 miniMic Standard, Center Channel, 1Mbps, Pre-scan and Final Data (Vertical), 12GHz to 18GHz miniMic Standard, Center Channel, 1Mbps, Pre-scan and Final Data (Horizontal), 12GHz to 18GHz Analog Devices, Inc. miniMic FCC 15.247 Certification Test Report WLL Report 19558-01 Rev 0 Page-60 of 112 Table 13: 3-meter Radiated Test Data, High Channel, 1Mbps, 1GHz to 18GHz, miniMic Standard Frequency (MHz) Detector Meas (dBuV/m) Limit (dBuV/m) Delta (dB) Turn Table (deg) Antenna (cm) 2480.00 TX Peak 87.225 -- -- 290 Horiz, 200 Avg -- -- -- 290 Horiz, 200 2483.5 BE Peak 42.458 67.225 * -24.737 290 Horiz, 200 Avg 27.629 54 -26.371 290 Horiz, 200 4960.00 Peak 54.573 74 -19.427 290 Horiz, 200 Avg 39.673 54 -14.327 290 Horiz, 200 7462.00 Peak 56.895 74 -17.105 290 Horiz, 200 Avg 41.054 54 -12.946 290 Horiz, 200 8987.00 Peak 59.316 74 -14.684 290 Horiz, 200 Avg 43.410 54 -10.590 290 Horiz, 200 11347.00 Peak 63.368 74 -10.632 290 Horiz, 200 Avg 47.680 54 -6.320 290 Horiz, 200 15160.00 Peak 60.073 74 -13.927 200 Vert, 125 Avg 45.315 54 -8.685 200 Vert, 125 15716.00 Peak 60.643 74 -13.357 290 Horiz, 200 Avg 44.895 54 -9.105 290 Horiz, 200 16667.00 Peak 62.823 74 -11.177 290 Horiz, 200 Avg 46.375 54 -7.625 290 Horiz, 200 * this limit is -20dBc based on the fundamental Analog Devices, Inc. miniMic FCC 15.247 Certification Test Report WLL Report 19558-01 Rev 0 Page-61 of 112 miniMic Standard, High Channel, 1Mbps, Pre-scan and Final Data (Vertical), 1GHz to 12GHz miniMic Standard, High Channel, 1Mbps, Pre-scan and Final Data (Horizontal), 1GHz to 12GHz Analog Devices, Inc. miniMic FCC 15.247 Certification Test Report WLL Report 19558-01 Rev 0 Page-62 of 112 miniMic Standard, High Channel, 1Mbps, Pre-scan and Final Data (Vertical), 12GHz to 18GHz miniMic Standard, High Channel, 1Mbps, Pre-scan and Final Data (Horizontal), 12GHz to 18GHz Analog Devices, Inc. miniMic FCC 15.247 Certification Test Report WLL Report 19558-01 Rev 0 Page-63 of 112 Table 14: 3-meter Radiated Test Data, Low Channel, 2Mbps, 1GHz to 18GHz, miniMic Standard Frequency (MHz) Detector Meas (dBuV/m) Limit (dBuV/m) Delta (dB) Turn Table (deg) Antenna (cm) 2390.0 BE Peak 40.827 69.881 * -29.054 290 Horiz, 200 Avg 26.184 54 -27.816 290 Horiz, 200 2402.0 TX Peak 89.881 -- -- 290 Horiz, 200 Avg -- -- -- 290 Horiz, 200 4804.00 Peak 54.502 74 -19.498 290 Horiz, 200 Avg 44.673 54 -9.327 290 Horiz, 200 10530.00 Peak 64.158 74 -9.842 290 Horiz, 200 Avg 48.578 54 -5.422 290 Horiz, 200 10938.00 Peak 64.676 74 -9.324 200 Vert, 125 Avg 48.601 54 -5.399 200 Vert, 125 11383.00 Peak 64.262 74 -9.738 290 Horiz, 200 Avg 48.146 54 -5.854 290 Horiz, 200 12532.00 Peak 55.978 74 -18.022 200 Vert, 125 Avg 42.378 54 -11.622 200 Vert, 125 13418.00 Peak 57.726 74 -16.274 290 Horiz, 200 Avg 42.943 54 -11.057 290 Horiz, 200 15221.00 Peak 59.416 74 -14.584 200 Vert, 125 Avg 45.706 54 -8.294 200 Vert, 125 * this limit is -20dBc based on the fundamental Analog Devices, Inc. miniMic FCC 15.247 Certification Test Report WLL Report 19558-01 Rev 0 Page-64 of 112 miniMic Standard, Low Channel, 2Mbps, Pre-scan and Final Data (Vertical), 1GHz to 12GHz miniMic Standard, Low Channel, 2Mbps, Pre-scan and Final Data (Horizontal), 1GHz to 12GHz Analog Devices, Inc. miniMic FCC 15.247 Certification Test Report WLL Report 19558-01 Rev 0 Page-65 of 112 miniMic Standard, Low Channel, 2Mbps, Pre-scan and Final Data (Vertical), 12GHz to 18GHz miniMic Standard, Low Channel, 2Mbps, Pre-scan and Final Data (Horizontal), 12GHz to 18GHz Analog Devices, Inc. miniMic FCC 15.247 Certification Test Report WLL Report 19558-01 Rev 0 Page-66 of 112 Table 15: 3-meter Radiated Test Data, Center Channel, 2Mbps, 1GHz to 18GHz, miniMic Standard Frequency (MHz) Detector Meas (dBuV/m) Limit (dBuV/m) Delta (dB) Turn Table (deg) Antenna (cm) 2440.00 TX Peak 88.886 -- -- 290 Horiz, 200 Avg -- -- -- 290 Horiz, 200 4879.00 Peak 52.551 74 -21.449 290 Horiz, 200 Avg 39.678 54 -14.322 290 Horiz, 200 7475.00 Peak 56.857 74 -17.143 290 Horiz, 200 Avg 41.245 54 -12.755 290 Horiz, 200 10841.00 Peak 64.114 74 -9.886 290 Horiz, 200 Avg 47.453 54 -6.547 290 Horiz, 200 1218.00 Peak 54.74 74 -19.26 200 Vert, 125 Avg 41.405 54 -12.595 200 Vert, 125 14231.00 Peak 57.41 74 -16.59 290 Horiz, 200 Avg 43.094 54 -10.906 290 Horiz, 200 14919.00 Peak 58.883 74 -15.117 200 Vert, 125 Avg 44.618 54 -9.382 200 Vert, 125 17349.00 Peak 62.318 74 -11.682 290 Horiz, 200 Avg 48.133 54 -5.867 290 Horiz, 200 Analog Devices, Inc. miniMic FCC 15.247 Certification Test Report WLL Report 19558-01 Rev 0 Page-67 of 112 miniMic Standard, Center Channel, 2Mbps, Pre-scan and Final Data (Vertical), 1GHz to 12GHz miniMic Standard, Center Channe…
Text truncated - open the document above for the full version.
Test Setup Photographs EUT Name: miniMic™ FCC ID: 2BUXT-MM1 Project: # 19558-01 (DTS) IC ID: N/A Conducted Radio Emissions, View 1 Conducted Radio Emissions, View 2 9kHz to 30MHz Radiated Emissions, View 1 9kHz to 30MHz Radiated Emissions, View 2 9kHz to 30MHz Radiated Emissions, View 3 9kHz to 30MHz Radiated Emissions, View 4 30MHz to 1GHz Radiated Emissions, View 1 30MHz to 1GHz Radiated Emissions, View 2 30MHz to 1GHz Radiated Emissions, View 3 Above 1GHz Radiated Emissions, View 1 Above 1GHz Radiated Emissions, View 2 Above 1GHz Radiated Emissions, View 3 Above 1GHz Radiated Emissions, EUT X Axis Above 1GHz Radiated Emissions, EUT Y Axis Above 1GHz Radiated Emissions, EUT Z Axis AC Powerline Conducted Emissions, View 1 AC Powerline Conducted Emissions, View 2 AC Powerline Conducted Emissions, AC/DC supply as tested
One Analog Way · Wilmington, Massachusetts, 01887 · United States
| # | Rule Parts | Frequency Range | Power Output |
|---|---|---|---|
| 1 | 15C | 2.40 GHz - 2.48 GHz | 300.00 µW |