2BVH3-C1016DoF Self-tracking Controller

Reference No.: WTX26X01026974W001/002 Page 1 of 14 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format FCC ID: 2BVH3-C101 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the device’s expected lifetime. Proposed Label Location on EUT FCC ID Label Location

RF Exposure Requirements Product Description: 6DoF Self-tracking Controller Model No.: C101 FCC ID: 2BVH3-C101 According to the KDB 447498 D01 v06 section 4.3.1, for 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ꞏ [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where - f(GHz) is the RF channel transmit frequency in GHz - Power and distance are rounded to the nearest mW and mm before calculation - The result is rounded to one decimal place for comparison Calculation Result: Bluetooth Tx frequency range: 2402-2480MHz Min. test separation distance: 5mm Maximum Conducted Output Power: 0.10dBm Tune-Up output power: 1.0dBm RF channel transmit frequency: 2402MHz Result: 0.39 Limit: 3.0 SRD 2.4G Tx frequency range: 2402-2480MHz Min. test separation distance: 5mm Maximum Conducted Output Power: 3.93dBm Tune-Up output power: 4.0dBm RF channel transmit frequency: 2440MHz Result: 0.78 Limit: 3.0 Note: Bluetooth and SRD 2.4G can't transmit at the same time. So the transmitter complies with the RF exposure requirements and the SAR is not required.

www.hubble-het.com|page1of8 KUNSHANHUBBLEELECTRONICSTECHNOLOGYCO.,LTD HubblePart No. 3.6.04.0212 Product Name HSD240918FPCAntenna WIFIAntenna2.4G&;2.5GConsumer- gradeHubble Featuremonopole FrequencyRange:2400MHz~2500MHz, ROHSCompliant Antenna manufacturer address A:No.100BinjiangNorthRoad,ZhangpuTown, Kunshan,Jiangsu,P.R.C www.hubble-het.com|page2of8 KUNSHANHUBBLEELECTRONICSTECHNOLOGYCO.,LTD EditionContentDate V0FirstRelease2026.4.15 www.hubble-het.com|page3of8 KUNSHANHUBBLEELECTRONICSTECHNOLOGYCO.,LTD 1.ElectricalSpecification 1.1PassiveEfficiency Frequency （MHz） Efficiency. db（db） Efficiency （%） Gain(dBi) 2400MHz -2.51 56% 3.95 2420MHz -2.52 56% 3.67 2440MHz -2.61 55% 3.57 2460MHz -2.74 53% 3.33 2480MHz -2.77 53% 3.19 2500MHz -2.8 52% 2.74 www.hubble-het.com|page4of8 KUNSHANHUBBLEELECTRONICSTECHNOLOGYCO.,LTD 1.2Sparameter VSWRS11 www.hubble-het.com|page5of8 KUNSHANHUBBLEELECTRONICSTECHNOLOGYCO.,LTD 2.MechanicalSpecifications Dimension(mm)39.44*9.66 Cabletype0.81 cablecolor&length(mm)Black/80 www.hubble-het.com| page 6 of8 KUNSHANHUBBLEELECTRONICSTECHNOLOGYCO.,LTD 2.4G~2.5G 2.4G www.hubble-het.com| page 7 of8 KUNSHANHUBBLEELECTRONICSTECHNOLOGYCO.,LTD 2.5G 4.Drawing

Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 1 of 44 TEST REPORT Reference No. ....................: WTX26X01026974W002 FCC ID ............................... .: 2BVH3-C101 Applicant .......................... .: Wuxi Xvisio Technology Co., Ltd. Address ............................ .: Floor 6, Building H1, No. 6 Jingxian Road, Xinwu District, Wuxi City, Jiangsu Province, China Manufacturer .................... .: The same as Applicant Address ............................ .: The same as Applicant Product Name .................. .: 6DoF Self-tracking Controller Model No.. ......................... .: C101 Standards ......................... .: FCC Part 15.247 Date of Receipt sample ... .: 2026-01-28 Date of Test....................... .: 2026-03-13 to 2026-03-24 Date of Issue .................... .: 2026-03-30 Test Report Form No. ...... . : WTX_Part 15_247W Test Result ........................ .: Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of approver. Prepared By: Waltek Testing Group (Shenzhen) Co., Ltd. Address: 1/F., Room 101, Building 1, Hongwei Industrial Park, Liuxian 2nd Road, Block 70 Bao'an District, Shenzhen, Guangdong, China Tel.: +86-755-33663308 Fax.: +86-755-33663309 Email: [email protected] Tested by: Approved by: Tris Li/Project Engineer Jason Su/Manager Reference No.: WTX26X01026974W002 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 2 of 44 TABLE OF CONTENTS 1. GENERAL INFORMATION .................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ......................................................................... 4 1.2 TEST STANDARDS ................................................................................................................................................. 5 1.3 TEST METHODOLOGY ........................................................................................................................................... 5 1.4 TEST FACILITY ...................................................................................................................................................... 5 1.5 EUT SETUP AND TEST MODE .............................................................................................................................. 6 1.6 MEASUREMENT UNCERTAINTY ............................................................................................................................. 7 1.7 TEST EQUIPMENT LIST AND DETAILS ................................................................................................................... 8 2. SUMMARY OF TEST RESULTS ......................................................................................................................... 12 3. ANTENNA REQUIREMENT ................................................................................................................................. 13 3.1 STANDARD APPLICABLE ..................................................................................................................................... 13 3.2 EVALUATION INFORMATION ................................................................................................................................ 13 4. POWER SPECTRAL DENSITY ........................................................................................................................... 14 4.1 STANDARD APPLICABLE ..................................................................................................................................... 14 4.2 TEST SETUP BLOCK DIAGRAM ........................................................................................................................... 14 4.3 TEST PROCEDURE .............................................................................................................................................. 14 4.4 SUMMARY OF TEST RESULTS/PLOTS ................................................................................................................. 14 5. DTS BANDWIDTH ................................................................................................................................................. 15 5.1 STANDARD APPLICABLE ..................................................................................................................................... 15 5.2 TEST SETUP BLOCK DIAGRAM ........................................................................................................................... 15 5.3 TEST PROCEDURE .............................................................................................................................................. 15 5.4 SUMMARY OF TEST RESULTS/PLOTS ................................................................................................................. 15 6. RF OUTPUT POWER ............................................................................................................................................ 16 6.1 STANDARD APPLICABLE ..................................................................................................................................... 16 6.2 TEST SETUP BLOCK DIAGRAM ........................................................................................................................... 16 6.3 TEST PROCEDURE .............................................................................................................................................. 16 6.4 SUMMARY OF TEST RESULTS/PLOTS ................................................................................................................. 16 7. FIELD STRENGTH OF SPURIOUS EMISSIONS ........…

Text truncated - open the document above for the full version.

Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 1 of 59 TEST REPORT Reference No. ....................: WTX26X01026974W001 FCC ID ............................... .: 2BVH3-C101 Applicant .......................... .: Wuxi Xvisio Technology Co., Ltd. Address ............................ .: Floor 6, Building H1, No. 6 Jingxian Road, Xinwu District, Wuxi City, Jiangsu Province, China Manufacturer .................... .: The same as Applicant Address ............................ .: The same as Applicant Product Name .................. .: 6DoF Self-tracking Controller Model No.. ......................... .: C101 Standards ......................... .: FCC Part 15.247 Date of Receipt sample ... .: 2026-01-28 Date of Test....................... .: 2026-03-13 to 2026-03-24 Date of Issue .................... .: 2026-03-30 Test Report Form No. ...... . : WTX_Part 15_247W Test Result ........................ .: Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of approver. Prepared By: Waltek Testing Group (Shenzhen) Co., Ltd. Address: 1/F., Room 101, Building 1, Hongwei Industrial Park, Liuxian 2nd Road, Block 70 Bao'an District, Shenzhen, Guangdong, China Tel.: +86-755-33663308 Fax.: +86-755-33663309 Email: [email protected] Tested by: Approved by: Tris Li/Project Engineer Jason Su/Manager Reference No.: WTX26X01026974W001 Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn Page 2 of 59 TABLE OF CONTENTS 1. GENERAL INFORMATION .................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ......................................................................... 4 1.2 TEST STANDARDS ................................................................................................................................................. 5 1.3 TEST METHODOLOGY ........................................................................................................................................... 5 1.4 TEST FACILITY ...................................................................................................................................................... 5 1.5 EUT SETUP AND TEST MODE .............................................................................................................................. 6 1.6 MEASUREMENT UNCERTAINTY ............................................................................................................................. 7 1.7 TEST EQUIPMENT LIST AND DETAILS ................................................................................................................... 8 2. SUMMARY OF TEST RESULTS ......................................................................................................................... 12 3. ANTENNA REQUIREMENT ................................................................................................................................. 13 3.1 STANDARD APPLICABLE ..................................................................................................................................... 13 3.2 EVALUATION INFORMATION ................................................................................................................................ 13 4. POWER SPECTRAL DENSITY ........................................................................................................................... 14 4.1 STANDARD APPLICABLE ..................................................................................................................................... 14 4.2 TEST SETUP BLOCK DIAGRAM ........................................................................................................................... 14 4.3 TEST PROCEDURE .............................................................................................................................................. 14 4.4 SUMMARY OF TEST RESULTS/PLOTS ................................................................................................................. 14 5. DTS BANDWIDTH ................................................................................................................................................. 15 5.1 STANDARD APPLICABLE ..................................................................................................................................... 15 5.2 TEST SETUP BLOCK DIAGRAM ........................................................................................................................... 15 5.3 TEST PROCEDURE .............................................................................................................................................. 15 5.4 SUMMARY OF TEST RESULTS/PLOTS ................................................................................................................. 15 6. RF OUTPUT POWER ............................................................................................................................................ 16 6.1 STANDARD APPLICABLE ..................................................................................................................................... 16 6.2 TEST SETUP BLOCK DIAGRAM ........................................................................................................................... 16 6.3 TEST PROCEDURE .............................................................................................................................................. 16 6.4 SUMMARY OF TEST RESULTS/PLOTS ................................................................................................................. 16 7. FIELD STRENGTH OF SPURIOUS EMISSIONS ........…

Text truncated - open the document above for the full version.