2BVJCDT82LEUMTCurtain Motor

Folding method for joint track (for easy transit) Search for the sl- ip part connected with the ends of the rubber belt Take off the screw of the slip parts and the connection bracket Push the connec- tion parts to one side Pull the slip parts slightly and separ- ate the connection part at the same time Fold the track Track folding method Unfold the folded track Combine the track slowly Push the con- nection bracket to the connec- tion part Screw the co- nnection bra- cket and install the slip parts The track is successfully assembled Restoring the track 1 2 3 4 5 3 1 2 3 4 5 Separate the lower cover and the profile. (Hold the cut end by hand, leaving 12cm outside the profile.) Fix the belt on the same side (to confirm the position of the other hanger arm). Make marks for easy holding of the hanger arm. Leave one tooth between these two belt fastening button Install the belt fasten button and the slip part as in the picture Install half of the master carrier as shown in the picture, and insert the track into the lower cover Slide the master carrier along the track direction to the right until it is flush with the profile cut surface at the track end, then fix it. Leave 12cm at the other end and cut. Leave half a tooth Use a screwdriver to install parts such as the gear into the lower cover Install both lower covers as shown in the picture Thread the belt into the track from one end and install it into the lower cover Install the belt fastening button at the cut end of the belt Profile length = Total track length - End cap length × 2 The total length of track is 2m The length of profiled material: 200cm-14cm=186cm Rubber belt assembly for curtain motor Profile dimension determination 2 1 Motor Installation The joint assembly of track S track 1 2 3 4 Insert the track joint board into both ends of the track Please refer to Rubber belt assembly for curtain motor for the following installation steps. Track joint board Insert the track joint bracket from one end to the connection point of both track ends Tighten the side screws Track joint bracket Note:1.The track needs to be joined when the length is less than required 2.The track needs to be engrafted when inconvenient to transport 4 Curtain motor installation 2 Assemble the curtain motor track at appropriate place, then fix with screws Finish assembling 5 Check whether the assembling is OK 4 Assemble the motor 3 1 Check the position of brackets,fix it at an appropriate place on the track Keep this end complete The overlap arm which is connected to the two ends of rubber belt 7cm End cap length The hook The marked position is the middle position of the other master carrier. Install the master carrier as shown in the picture, with half inside the profile. 12cm The slip parts e.g. These two slip parts are successfully installedSlide the runners into the track After one slip part installed,then thread the other end of the belt through the other lower cover The runners are installedPlace the hook and the upper cover into the track Install the belt fasten button and the slip part as in the picture 1. Do not expose motor to humid or extreme temperature conditions. 2. Do not cut the antenna and keep it clear from metal objects. 3. Do not allow children to play with this device. 4. If power cable or connector is damaged, do not use. 5. Ensure power cable and aerial are clear and protected from moving parts. 6. Cable routed through walls shall be properly isolated. 7. Before installation, remove unnecessary cords and disable equipment not needed for powered operation. 8. Installation and programming to be performed by a qualified professional, use or modification outside the scope of this instruction may void warranty. Caution * For more motor models and specific torque, please refer to the nameplate. Working Temperature: -10°C~60°C Input voltage: 5 VDC Radio Frequency: 433.92 MHz Max. Single Running Time: 4 min Specifications Fields of Application For motorized curtain and motorized lift curtain. Features Matter over Thread Electronic Limit Memory Stall Protection Run/Stop By Pulling Fabric External Switch Function Built-in Receiver Preferred Stop Position Hand Pull Start/Soft Start and Soft Stop/Anti Fabric Compression Switch Direction Manual-set the Open and Close Limits Reset to Factory Mode Common wire (black)Stop wire (red)Close wire (green)Open wire (yellow) Product Introduction P1 button Dry contact interface LED indicator Antenna×2 Type-C charging port 1 Manual-set/remove the open limit or OPENCLOSEOPEN +→→ STOPOPEN + STOP After setting the limits, after operating the curtains to the desired open limit position, press and hold the OPEN and STOP buttons simultaneously for 5 seconds (1 slowly flash and 1 long beep), press OPEN or CLOSE button or manually pull the curtain to adjust it to the desired open limit position, press and hold the OPEN and STOP buttons simultaneously for 2 seconds (5 flashes and 3 beeps), the new open limit is set. • Repeating this procedure will remove the open limit. 5 Manual-set/Remove the Open and Close Limits Press P2 once (1 flash and 1 beep) and P2 once again (1 flash and 1 beep) on the existing emitter, press P2 once on the new emitter (5 flashes and 3 beeps), new emitter is paired to the motor. • Repeating this procedure will delete the newly paired emitter. →→ P2(a)P2(a)P2(b) * (a) as existing emitter, (b) as new emitter to pair/delete. 3 Setting Limits → OPENCLOSE Press OPEN once, the curtain will open until it stops against obstacle, the open limit is set. Then press CLOSE once, the curtain will close until it stops against obstacle, the close limit is set. When both the open and close limits are set successfully, the motor LED flashes 5 times and beeps 3 times, the limit is set successfully. 4 Pairing/Deleting Additional Emitter Essential Settings Step 1 to 3 must be completed to ensure proper operation. -4- 1 Pairing → P1 STOP Press and hold the P1 button for 2 seconds (1 flash), release the button, the mo…

Text truncated - open the document above for the full version.

Hangzhou Tangpushi Home Products Co., LTD 071426-19 Certification Application Attestation Statements Date: Aug 10, 2026 American Certification Body, Inc. 3060 Williams Drive, Suite 300 #104 Fairfax, VA 22031 To Whom It May Concern: Statement for 47 CFR section 2.911(d)(5)(i) ______( Hangzhou Tangpushi Home Products Co., LTD)______ certifies that as of the date of the application the equipment for which authorization is sought is not “covered” equipment 1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not “covered” equipment. Additional Explanation: <N/A> Statement for 47 CFR section 2.911(d)(5)(ii) ______( Hangzhou Tangpushi Home Products Co., LTD)______ (“the applicant”) certifies that, as of the date of the filing of this application, the applicant ☐ - is / ☒ - is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates – see KDB 986446 Question 5) as an entity producing “covered” equipment. The applicant also certifies that the device does not have cybersecurity and/or anti-virus software produced by Kaspersky Lab, Inc or any of its successors and assignees identified on the covered list installed on the device, nor will it be installed by the applicant at any time after certification. Thank you, By: __________________________ ______ XIAOHUA CHEN _________ (Signature 2 ) (Print name) Title: ___ Certified Engineer ________________ Company: __ Hangzhou Tangpushi Home Products Co., LTD___ Telephone: ___ (243) 843-9711 ___ 1 - The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist . 2 - Letters must be placed on appropriate letterhead.

Hangzhou Tangpushi Home Products Co., LTD 071426 – 19 Authority to Act as Agent Date: Aug 10, 2026 American Certification Body, Inc. 3060 Williams Drive, Suite 300 #104 Fairfax, VA 22031 To Whom It May Concern: ______Intertek Testing Services (Shanghai FTZ) Co., Ltd______ is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: _____ Dec 31, 2027____ By: __________________________ _____ XIAOHUA CHEN______ (Signature 1 ) (Print name) Title: ______ Certified Engineer ____________________ On behalf of: __ Hangzhou Tangpushi Home Products Co., LTD ________________ (Company Name) Telephone: _____ (243) 843-9711 ___________________ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Hangzhou Tangpushi Home Products Co., LTD Request for Confidentiality Date: Aug 12, 2026 Subject: Confidentiality Request for: __FCC ID: 2BVJCDT82LEUMT Pursuant to FCC 47 CFR 0.457(d) and 0.459, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit ☐ Short Term ☒ Permanent Block Diagrams ☐ Short Term External Photos ☐ Short Term ☐ Permanent * 1 Internal Photos ☐ Short Term ☒ Permanent Operation Description/Theory of Operation ☐ Short Term ☒ Permanent Parts List & Placement/BOM ☐ Short Term ☐ Permanent Tune-Up Procedure ☐ Short Term ☒ Permanent Schematics ☐ Short Term Test Setup Photos ☐ Short Term ☐ Permanent * 3 User’s Manual ______ Hangzhou Tangpushi Home Products Co., LTD. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___ ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By: XIAOHUA CHEN (Signature/Title 2 ) (Print name) 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at: https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Declaration Letter Related FCC ID: 2BVJCDT82LEUMT Justification statement stating that all measurements for RF part were performed by radiated method and therefore additional antenna gain documentation is not required for RF part. See “internal photo” for the details of the antenna. By: ______________ ____Teddy Yin ______ (Signature) (Print name) Title: ____Supervisor________ Company: ____Intertek Testing Services (Shanghai FTZ) Co., Ltd.________

FCC ID: 2BVJCDT82LEUMT Page 1 of 3 External Picture FCC ID: 2BVJCDT82LEUMT Page 2 of 3 FCC ID: 2BVJCDT82LEUMT Page 3 of 3

Label location

W2242-1-03 符合：ROHS REACH法规要求 0.5#亚银 彩色印刷 W2242-1-03 W2242# 校对 设计 适用产品 尺 寸 材 质 油 墨 印刷工艺 是否含流水码 或条形码 审定 版本 日期 制图 是否覆膜 颜 色 使用规范 备注: 工艺描述 客户号 杜亚机电 铭牌 JS-6-15 0.1±0.01mm（厚度）34.3x26.2mm（长*宽） DT82LEU/MT-1.2/14 常规油墨 覆哑膜 贴电机 贴小包 图纸认证说明 (此尺寸为本图内1:1尺寸) 5.2mm 7.2mm 2026.7.8 A-00 高瑛 孙世鑫 C:65% M:73% Y:84% K:40% 5.2mm 7.2mm DT82LEU/MT-1.2/14 1.2Nm 5VDC 2A Class A IP40 14cm/s 10W 12min Curtain Motor FCC ID:2BVJCDT82LEUMT Contains FCC lD: VYYHRN71 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. DT82LEU/MT-1.2/14 1.2Nm 5VDC 2A Class A IP40 14cm/s 10W 12min Curtain Motor FCC ID:2BVJCDT82LEUMT Contains FCC lD: VYYHRN71 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. DT82LEU/MT-1.2/14 1.2Nm 5VDC 2A Class A IP40 14cm/s 10W 12min Curtain Motor FCC ID:2BVJCDT82LEUMT Contains FCC lD: VYYHRN71 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC ID: 2BVJCDT82LEUMT Page 1 of 6 Internal Picture 433.92 MHz antenna BLE module antenna FCC ID: 2BVJCDT82LEUMT Page 2 of 6 FCC ID: 2BVJCDT82LEUMT Page 3 of 6 FCC ID: 2BVJCDT82LEUMT Page 4 of 6 FCC ID: 2BVJCDT82LEUMT Page 5 of 6 FCC ID: 2BVJCDT82LEUMT Page 6 of 6

Hangzhou Tangpushi Home Products Co., LTD MPE ASSESSMENT REPORT Report Type: FCC MPE assessment report Model: DT82LEU/MT-1.2/14 REPORT NUMBER: 260700296SHA-002 ISSUE DATE: Aug 12, 2026 DOCUMENT CONTROL NUMBER: TTRFFCCMPE-01_V1 © 2018 Intertek Intertek Testing Services (Shanghai FTZ) Co., Ltd Building No.86, 1198 Qinzhou Road (North) Caohejing Development Zone Shanghai 200233, China Telephone: 86 21 6127 8200 www.intertek.com TEST REPORT This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. TTRFFCCMPE-01_V1© 2018 Intertek Page 2 of 8 Report no.: 260700296SHA-002 Applicant: Hangzhou Tangpushi Home Products Co., LTD Room 1502-01, Building 2, Xizi International Center, Nanyuan Street, Linping District, Hangzhou, 311199, China Manufacturer: Hangzhou Tangpushi Home Products Co., LTD Room 1502-01, Building 2, Xizi International Center, Nanyuan Street, Linping District, Hangzhou, 311199, China FCC ID: 2BVJCDT82LEUMT SUMMARY: The equipment complies with the requirements according to the following standard(s) or Specification: KDB447498 D01 General RF Exposure Guidance v06 FCC Part2.1091, FCC Part1.1307(b) PREPARED BY: REVIEWED BY: Project Engineer Teddy Yin Reviewer Wakeyou Wang Report No.: 260700296SHA-002 TEST REPORT TTRFFCCMPE-01_V1© 2018 Intertek Page 3 of 8 Revision History Report No. Version Description Issued Date 260700296SHA-002 Rev. 01 Initial issue of report Aug 12, 2026 Report No.: 260700296SHA-002 TEST REPORT TTRFFCCMPE-01_V1© 2018 Intertek Page 4 of 8 1 GENERAL INFORMATION 1.1 Description of Equipment Under Test (EUT) Product name: Curtain Motor Type/Model/PMN/HVIN: DT82LEU/MT-1.2/14 Description of EUT: The EUT can transmit 433.92MHz signal. Rating: USB input: DC 5V EUT type: Table top Floor standing Hardware Version: / Software Version: / Sample No.: A260722-51-001 Sample received date: Jul 24, 2026 Date of test: Jul 24~Aug 6, 2026 1.2 Technical Specification Operation Frequency: 433.92MHz Type of Modulation: FSK Product Type: Mobile Portable Fix Location Channel Number: 1 Antenna Information: line antenna(declared by the manufacturer) Report No.: 260700296SHA-002 TEST REPORT TTRFFCCMPE-01_V1© 2018 Intertek Page 5 of 8 1.3 Description of Test Facility Name: Intertek Testing Services (Shanghai FTZ) Co., Ltd. Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Telephone: 86 21 61278200 Telefax: 86 21 54262353 The test facility is recognized, certified, or accredited by these organizations: CNAS Accreditation Lab Registration No. CNAS L21189 FCC Accredited Lab Designation Number: CN0175 IC Registration Lab CAB identifier.: CN0014 VCCI Registration Lab Registration No.: R-14243, G-10845, C-14723, T-12252 A2LA Accreditation Lab Certificate Number: 3309.02 Report No.: 260700296SHA-002 TEST REPORT TTRFFCCMPE-01_V1© 2018 Intertek Page 6 of 8 2 MPE Assessment Test result: Pass 2.1 MPE Assessment Limit Mobile device exposure for standalone operations: Frequency range E-field strength (V/m) H-field strength (A/m) B-field (uT) Equivalent plane wave power density S eq (W/m 2 ) 0-1 Hz - 3,2 × 10 4 4 × 10 4 - 1-8 Hz 10 000 3,2 × 10 4 /f 2 4 × 10 4 /f 2 - 8-25 Hz 10 000 4 000/f 5 000/f - 0,025-0,8 kHz 250/f 4/f 5/f - 0,8-3 kHz 250/f 5 6,25 - 3-150 kHz 87 5 6,25 - 0,15-1 MHz 87 0,73/f 0,92/f - 1-10 MHz 87/f 1/2 0,73/f 0,92/f - 10-400 MHz 28 0,073 0,092 2 400-2 000 MHz 1,375 f 1/2 0,0037 f 1/2 0,0046 f 1/2 f/200 2-300 GHz 61 0,16 0,20 10 Mobile device exposure for simultaneous transmission operations: the sum of the MPE ratios for all simultaneously transmitting antennas incorporated in a host device is ≤ 1.0 Report No.: 260700296SHA-002 TEST REPORT TTRFFCCMPE-01_V1© 2018 Intertek Page 7 of 8 2.2 Assessment Results Power density (S) is calculated according to the formula: S = PG / (4πR²) Where S = power density in mW/cm² P = Radiated transmit power in mW G = numeric gain of transmit antenna R = distance (cm) 433.92MHz Field Strength EIRP EIRP Distance MPE dBuV/m dBm mW cm mW/cm² 89.60 -5.7 0.27 20 0.00005 Note: EIRP= E-95.3 where: E=electric field strength in dBuV/m, EIRP= equivalent isotropic radiated power BLE & Thread Mode Max. Peak power incl. tune-up (dBm) Maximum EIRP(dBm) Maximum EIRP(mW) Distance (cm) MPE (mW/cm²) BLE 7 8 6.31 20 0.001 Thread 7 8 6.31 20 0.001 Note: BLE and Thread cannot transmit simultaneously as they share the same antenna. so the maximum rate of MPE is 0.001/1+0.00005/0.217=0.0012< 1 Report No.: 260700296SHA-002 TEST REPORT TTRFFCCMPE-01_V1© 2018 Intertek Page 8 of 8 Appendix I Definition below must be outlined in the User Manual: To satisfy FCC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. ******************************************* END ************************************

Declaration Letter Related FCC ID: 2BVJCDT82LEUMT Justification statement stating that all measurements for RF part were performed by radiated method and therefore additional antenna gain documentation is not required for RF part. See “internal photo” for the details of the antenna. By: ______________ ____Teddy Yin ______ (Signature) (Print name) Title: ____Supervisor________ Company: ____Intertek Testing Services (Shanghai FTZ) Co., Ltd.________

Hangzhou Tangpushi Home Products Co., LTD RF TEST REPORT Report Type: FCC Part 15.231 RF report Model: DT82LEU/MT-1.2/14 REPORT NUMBER: 260700296SHA-001 ISSUE DATE: Aug 12, 2026 DOCUMENT CONTROL NUMBER: TTRF15.231_V1 © 2018 Intertek Intertek Testing Services (Shanghai FTZ) Co., Ltd. Building No.86, 1198 Qinzhou Road (North) Caohejing Development Zone Shanghai 200233, China Telephone: 86 21 6127 8200 www.intertek.com TEST REPORT This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. TTRF15.231_V1 © 2018 Intertek Page 2 of 28 Report no.: 260700296SHA-001 Applicant: Hangzhou Tangpushi Home Products Co., LTD Room 1502-01, Building 2, Xizi International Center, Nanyuan Street, Linping District, Hangzhou, 311199, China Manufacturer: Hangzhou Tangpushi Home Products Co., LTD Room 1502-01, Building 2, Xizi International Center, Nanyuan Street, Linping District, Hangzhou, 311199, China FCC ID: 2BVJCDT82LEUMT SUMMARY: The equipment complies with the requirements according to the following standard(s) or Specification: 47CFR Part 15 (2024): Radio Frequency Devices (Subpart C) ANSI C63.10 (2020)+Cor.1(2023)+C63.10a(2024)+Errata to C63.10a(2024): American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices PREPARED BY: REVIEWED BY: Project Engineer Teddy Yin Reviewer Wakeyou Wang Report No.: 260700296SHA-001 TEST REPORT TTRF15.231_V1 © 2018 Intertek Page 3 of 28 Content REVISION HISTORY................................................................................................................................................ 4 MEASUREMENT RESULT SUMMARY ..................................................................................................................... 5 1 GENERAL INFORMATION ............................................................................................................................. 6 1.1 DESCRIPTION OF EQUIPMENT UNDER TEST (EUT) ..................................................................................................... 6 1.2 TECHNICAL SPECIFICATION .................................................................................................................................... 6 1.3 DESCRIPTION OF TEST FACILITY .............................................................................................................................. 7 2 TEST SPECIFICATIONS ................................................................................................................................... 8 2.1 STANDARDS OR SPECIFICATION ............................................................................................................................... 8 2.2 MODE OF OPERATION DURING THE TEST ................................................................................................................... 8 2.3 TEST SOFTWARE LIST ............................................................................................................................................ 8 2.4 TEST PERIPHERALS LIST ......................................................................................................................................... 8 2.5 TEST ENVIRONMENT CONDITION: ............................................................................................................................ 8 2.6 INSTRUMENT LIST ................................................................................................................................................ 9 2.7 MEASUREMENT UNCERTAINTY ............................................................................................................................. 10 3 FUNDAMENTAL & SPURIOUS EMISSION & RESTRICT BAND RADIATED EMISSION ...................................... 11 3.1 LIMIT .............................................................................................................................................................. 11 3.2 MEASUREMENT PROCEDURE ............................................................................................................................... 12 3.3 TEST CONFIGURATION ........................................................................................................................................ 13 3.4 TEST RESULTS OF RADIATED EMISSIONS ................................................................................................................. 15 4 POWER LINE CONDUCTED EMISSION ......................................................................................................... 20 4.1 LIMIT .............................................................................................................................................................. 20 4.2 TEST CONFIGURATION ........................................................................................................................................ 20 4.3 MEASUREMENT PROCEDURE ............................................................................................................................... 21 4.4 TEST RESULTS OF POWER LINE CONDUCTED EMISSION.....................................................................…

Text truncated - open the document above for the full version.

FCC ID: 2BVJCDT82LEUMT Page 1 of 3 Test Setup FCC ID: 2BVJCDT82LEUMT Page 2 of 3 1. Radiated Emission Above 1GHz Below 1GHz FCC ID: 2BVJCDT82LEUMT Page 3 of 3 2. Conducted Emission