2BVSN-MBM2BLECLIQ Connect mobilePD BLE

PB0003100027000 0E, 07.2026 Benutzeranleitung / User Instructions / Instructions d’utilisation CLIQ Mobile PD Mobiles Programmiergerät / Mobile Programming Device / Programmeur portable DE Bedienung A Achtung! Drehen des Schlüssels in der Schlüsselaufnahme kann das Gerät beschädigen: Die Schlüsselauf- nahme ist starr. Den Schlüssel nur einstecken, nicht drehen! I Hinweis! Zum Betrieb des Programmiergerätes sind vier 1,5 V Batterien Typ AAA/LR03 erforderlich (nicht im Lieferumfang enthalten). Das Programmiergerät muss mit einer Daten- quelle verbunden werden, um verwendet werden zu können. Zur Einrichtung dieser Verbindung beachten Sie den Quick Guide (PB00100). EN Operation A Attention! Turning the key in the key slot can damage the device: The key slot is rigid. Only insert the key, do not turn it! I Note! The programming device requires four 1.5 V AAA/ LR03 batteries (not included in delivery). The programming device must be connected to a data source in order to be used. Refer to the Quick Guide (PB00100) to set up this connection. FR Utilisation A Attention ! Tourner la clé dans le logement de clé peut en- dommager l’appareil : Le logement de clé est ri- gide. Insérer simplement la clé, ne pas la tourner ! I Remarque ! Quatre piles 1,5 V de type AAA/LR03 (non four- nies) sont nécessaires au fonctionnement du programmeur. Pour pouvoir être utilisé, le programmeur doit être connecté à une source de données. Reportez-vous au Guide rapide (PB00100) pour configurer cette connexion. 1 2 3 4 5 1 Schlüssel in die Schlüsselaufnahme stecken. 2 Das Programmiergerät stellt die Verbindung zur Datenquelle her. 3 Die Daten werden auf den Schlüssel program- miert. Dies dauert je nach Datenmenge wenige Sekunden bis ca. eine Minute. Währenddessen leuchtet das Symbol. 4 Bei jedem Programmiervorgang werden die Uhrzeit und das Datum im Schlüssel aktualisiert. 5 Wenn der Programmiervorgang erfolgreich ab- geschlossen ist, ertönt ein Signalton. Das Sym- bol leuchtet dauerhaft. 6 Den Schlüssel entfernen. 1 Insert key into the key slot, leave key there. 2 The programming device establishes the con- nection to the data source. 3 The data is programmed onto the key. Depending on the amount of data, this may take a few sec- onds to approximately one minute. The symbol flashes during this time. 4 Time and date in the key will be updated with every programming operation. 5 When programming has successfully completed, a beep sounds. The symbol lights up continu- ously. 6 Remove key from key slot. 1 Insérer la clé dans le logement de clé. 2 Le programmeur établit la connexion avec la source de données. 3 Les données sont programmées sur la clé. Selon la quantité de données, cela peut prendre de quelques secondes à environ une minute. Pendant ce temps, le symbole clignote. 4 À chaque programmation, l’heure et la date sont actualisées dans la clé. 5 Un signal sonore retentit lorsque le processus de programmation est terminé avec succès. Le symbole s’allume en continu. 6 Retirer la clé. ASSA ABLOY Sicherheitstechnik GmbH Bildstockstraße 20 72458 Albstadt DEUTSCHLAND Tel. + 49 7431 123-0 albstadt @ assaabloy.com www.assaabloy.com/de AnzeigenIndicationsAfficher BetriebsanzeigeOperation IndicatorIndicateur d’état de fonctionnement Blinkt:Netzwerk wird initialisiert.Flashing:Network connection is being initialized. Clignote :Initialisation du réseau. Leuchtet:Das System ist aktiv und bereit.Lights up:The system is active and ready.S’allume :Le système est actif et prêt. BatteriestatusLevel of batteryÉtat de la pile Blinkt:Die Batteriespannung des Schlüssels reicht nur noch für wenige Betätigungen. Schlüsselbatterie sofort erneuern. Flashing:The battery voltage of the key is only sufficient for a few actuations. Replace the key battery immediately. Clignote :La tension de la pile de la clé ne suffit plus que pour quelques ac- tionnements. Remplacer immédiatement la pile de la clé. Verbindung zur DatenquelleConnection to data sourceConnexion à la source de données Blinkt:Die Verbindung wird aufgebaut.Flashing:The connection is beeing established. Clignote :La connexion est en cours d’établissement. Leuchtet:Die Verbindung ist hergestellt.Lights up:The connection has been established. S’allume :La connexion est établie. SchreibvorgangKey writingÉcriture de la clé Blinkt:Der Schreibvorgang läuft. Den Schlüssel nicht entfernen. Flashing:Key writing in progress. Do not re- move the key. Clignote :L’écriture est en cours. Ne pas reti- rer la clé. Leuchtet:Der Schreibvorgang ist abgeschlos- sen. Es ertönt ein Signalton. Lights up:Key writing is finished. A beep sounds. S’allume :Le processus d’écriture est terminé. Un signal sonore retentit. Nachrichten (nur wenn die Funktion E-Mail- Benachrichtigung verwendet wird) Message (Only if using email notification)Messages (uniquement si la fonction de noti- fication par e-mail est utilisée) Leuchtet:Wenn eine neue Nachricht vorhanden ist. Lights up:If a new email is available.S’allume :Lorsqu’un nouveau message est disponible. FehlerErrorsErreur Beim Auftreten eines Fehlers ertönen 3 Signaltöne. If an error occurs, 3 beeps will sound.En cas d’erreur, 3 signaux sonores retentissent. Blinkt: Blinkt: Die Batteriespannung des Programmier gerätes ist niedrig. Batterien des Programmiergerätes erneuern. Flashing: Flashing: The battery voltage of the programming device is low. Replace the programming device batteries. Clignote : Clignote : La tension des piles du program- meur est faible. Remplacer les piles du programmeur. Leuchtet: Leuchtet: Verbindungsaufbau fehlgeschlagen. Erneut versuchen. Falls der Verbin- dungsaufbau weiterhin fehlschlägt, kontaktieren Sie den Systemadministrator. Lights up: Lights up: Failed to connect. Try again. If the connection contin- ues to fail, contact the system administrator. S’allume : S’allume : La connexion a échoué. Réessayer. Si la connexion continue d’échouer, contactez l’administra- teur système. DE Rechtliche Hinweise ASSA ABLOY Sicherheitstechnik Gmb…

Text truncated - open the document above for the full version.

ASSA ABLOY Sicherheitstechnik GmbH, Goerzallee 299, 14167 Berlin, GERMANY Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 8/12/2026 To whom it may concern: We, ASSA ABLOY Sicherheitstechnik GmbH, hereby certify that the equipment for which authorization is sought (FCC ID: 2BVSN-MBM2BLE ) is not “covered” equipment prohibited from receiving an equipment authorization pursuant to § 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www.fcc.gov/supplychain/coveredlist) as an entity producing “covered” equipment. We also certify that, as of the date of the filing of the application, the equipment does not utilize cyber- security or anti-virus software from Kapersky Lab, Inc, or any of its successors and assignees, which is also on the “covered list” By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(b) and (d)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. Sincerely, Signature: Jasmin Thiel Patents and certification employee ASSA ABLOY Sicherheitstechnik GmbH 62_[model] CoveredEqu_2.911(d)(5)(i) and (ii)-U, V04

ASSA ABLOY Sicherheitstechnik GmbH, Goerzallee 299, 14167 Berlin, GERMANY Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 8/12/2026 To whom it may concern: We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2BVSN-MBM2BLE including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins’ current valid General Terms and Conditions (AGB),Testing and Certification Regulations (PZO) which can be viewed on following website www.eurofins.de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Signature Jasmin Thiel Patents and certification employee ASSA ABLOY Sicherheitstechnik GmbH

05_G0M22603-0004_144723 ConReq-US_G0M22603-0004_144723 ConReq - U_V02 ASSA ABLOY Sicherheitstechnik GmbH, Goerzallee 299, 14167 Berlin, GERMANY 1/2 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 8/12/2026 Request for Confidentiality Company name: ASSA ABLOY Sicherheitstechnik GmbH FCC ID: 2BVSN-MBM2BLE In accordance with CFR 47 §0.457(d) and CFR 47 §0.459 of the Commission’s Rules, ASSA ABLOY Sicherheitstechnik GmbH hereby requests confidentiality of following exhibits: Exhibit Type: Type of Confidentiality Requested Detailed block diagrams* x Long-term confidentiality Schematic diagrams* x Long-term confidentiality Detailed operational descriptions* x Long-term confidentiality Parts lists/ tune up information* x Long-term confidentiality External photos Short-term confidentiality** Internal photos Short-term confidentiality** Test setup photos Short-term confidentiality** User’s manual Short-term confidentiality** Short-term maximum confidentiality period: 180 days OR: Short-term confidentiality release date (product launch): 04/08/2026 * Exhibits not routinely made available to the public. ** Only if applicable: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. When the device is marketed the grantee must inform the TCB to release the Short-Term Confidentiality information withheld on the FCC equipment authorization website. 05_G0M22603-0004_144723 ConReq-US_G0M22603-0004_144723 ConReq - U_V02 2/2 Long-term confidentiality: The documents indicated as long-term confidential contain detailed system and equipment description and related information about the product which ASSA ABLOY considers to be proprietary, confidential and a custom design and the information is not publicly available. Since the design is a basis from which future technological products will evolve, ASSA ABLOY considers that this information would be of benefit to its competitors and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Short-term confidentiality (if applicable): ASSA ABLOY requests the exhibits selected above as short-term confidential to be withheld from public view for the period as indicated above. When the device is marketed, ASSA ABLOY will inform the TCB to release the short-term confidentiality information withheld on the FCC equipment authorization website. Sincerely, Signature Jasmin Thiel Patents and certification employee ASSA ABLOY Sicherheitstechnik GmbH

Brian Dodge Director, New Product Development Medeco Security Locks ASSA ABLOY Opening Solutions Medeco Security Locks 3625 Alleghany Drive Salem, VA 24153 USA Phone : +1 540 633 3261 Mobile : +1 540 824 2106 Email : [email protected] Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2026-04-30 U.S. Agent Designation ASSA ABLOY Sicherheitstechnik GmbH acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2BVSN-MBM2BLE): Name of contact person (U.S. agent)*: Brian Dodge Company of U.S. agent (if applicable): Medeco Security Locks, a division of ASSA ABLOY High Security Group INC. Physical U.S. address of agent* (PO box is not acceptable): Medeco Security Locks 3625 Alleghany Drive Salem, VA 24153 USA FRN of U.S. agent*: 0017065285 Email address of U.S. agent*: [email protected] Phone number of U.S. agent*: 540 824 2106 Brian Dodge acknowledges their obligation to accept service of process on behalf of ASSA ABLOY Sicherheitstechnik GmbH. ASSA ABLOY Sicherheitstechnik GmbH with the FRN 0038330601 accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under § 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. By signing this agreement, the U.S. agent agrees to respond to inquiries from Eurofins Product Services GmbH (TCB) or the FCC in order to verify accuracy of the information provided within 7 days of receipt. Sincerely, Name: Frank Stier Title: CTO Central Europe Company: ASSA ABLOY Name: Brian Dodge Title: Director, New Product Development Company: Medeco Security Locks, ASSA ABLOY High Security Group

Appendix 1 to Test Report No.: G0M-2509-3304-TFC247BL01-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 3 of 11 ANNEX C Equipment photos Photos – Equipment External EUT IN PERSPECTIVE I EUT IN PERSPECTIVE II Appendix 1 to Test Report No.: G0M-2509-3304-TFC247BL01-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 4 of 11 EUT FRONT SIDE EUT REAR SIDE Appendix 1 to Test Report No.: G0M-2509-3304-TFC247BL01-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 5 of 11 EUT RIGHT SIDE EUT LEFT SIDE Appendix 1 to Test Report No.: G0M-2509-3304-TFC247BL01-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 6 of 11 EUT TOP SIDE EUT BOTTOM SIDE Appendix 1 to Test Report No.: G0M-2509-3304-TFC247BL01-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 7 of 11 EUT CONDUCTED SAMPLE EUT WITH ALL ACCESSORIES Appendix 1 to Test Report No.: G0M-2509-3304-TFC247BL01-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 11 of 11 Photos – Auxiliary/Associated Equipment JTAG ADAPTER WITH USB CABLE JTAG ADAPTER WITH USB CABLE BACK

Appendix 1 to Test Report No.: G0M-2509-3304-TFC247BL01-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 8 of 11 Photos – Equipment Internal EUT HOUSING EUT BATTERIES Appendix 1 to Test Report No.: G0M-2509-3304-TFC247BL01-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 9 of 11 EUT PCB TOP SIDE EUT PCB BOTTOM SIDE Appendix 1 to Test Report No.: G0M-2509-3304-TFC247BL01-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 10 of 11 EUT LABEL EUT RADIO PART Appendix 1 to Test Report No.: G0M-2509-3304-TFC247BL01-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 11 of 11 Photos – Auxiliary/Associated Equipment JTAG ADAPTER WITH USB CABLE JTAG ADAPTER WITH USB CABLE BACK

DUO mXTEND TM (NN03-320) DATASHEET Last Update: April 2024 DATASHEET DUO mXTEND TM (NN03-320) DUO mXTEND™ (NN03-320) The DUO mXTEND™ antenna booster can provide optimal performance, even under the restriction of having no ground clearance beyond the antenna footprint. This miniature and multipurpose component is designed to provide GNSS and Bluetooth connectivity worldwide, simultaneously, as well as other regions of the spectrum, such as 5G and UWB, simultaneously, thanks to its multiport nature. Product Benefits • Multipurpose: Multiband and multi-RAT IoT chip antenna component with 2 independent ports. • Smallest clearance: No clearance beyond the antenna footprint. • Miniature: Small form factor of 7.0 mm x 3.0 mm x 2.0 mm. • Best for combining: One or more GNSS, Bluetooth, UWB and 5G applications. • Versatile: Dual mounting on device corner or center edge. • Reliability: Off-the-Shelf standard product, no antenna part customization (electronic optimization). • Use cases: tracking devices, wearables, gaming devices, IoT-5G modules. Operation Bands Summary • GNSS, Bluetooth, 5G and UWB (1561 – 1606MHz, 2400 – 2500MHz, 3400 – 3800MHz, 3100 – 4800MHz and 6000 – 10600 MHz). Last Update: April 2024 DATASHEET DUO mXTEND TM (NN03-320) 1. AVAILABLE SOLUTIONS SUMMARY Class Frequency Regions Frequency range More detailed info 2 Ports 4 1561MHz, 1575MHz, 1598MHz to 1606MHz, and 2400MHz to 2500MHz. GNSS + BLUETOOTH 1 Port 3 1561 MHz, 1575 MHz, 1598MHz to 1606MHz GNSS 1 Port 1 2400 MHz to 2500 MHz BLUETOOTH 1 Port 1 3400 MHz to 3800 MHz 5G 1 Port 1 3100 MHz to 4800 MHz and 6000 MHz to 10600 MHz UWB 1 Port 2 2400MHz to 2500MHz, 4900MHz to 5900MHz WIFI DUAL BAND 2. DETAILED AVAILABLE SOLUTIONS 2.1. GNSS AND BLUETOOTH SOLUTION (2-port) Technical features BeiDou GPS & GALILEO GLONASS Bluetooth 1561MHz 1575MHz 1598 – 1606MHz 2400 – 2500MHz Average Efficiency > 40% > 45% > 50% > 50% Peak Gain -1.1 dBi -1.0 dBi -1.0 dBi -0.9 dBi VSWR < 3:1 Radiation Pattern Omnidirectional Polarization Linear Weight (approx.) 0.11 g. Temperature -40 to +125 ºC Impedance 50  Dimensions (L x W x H) 7.0 mm x 3.0 mm x 2.0 mm Technical features. Measures from the evaluation board (80 mm x 40 mm x 1 mm). Last Update: April 2024 DATASHEET DUO mXTEND TM (NN03-320) 2.2 GNSS SOLUTION (1-port) Technical features 1561 MHz 1575 MHz 1598 – 1606 MHz Average Efficiency > 60 % > 70 % > 60 % Peak Gain 1.6 dBi 1.8 dBi 1.1 dBi VSWR < 2.5:1 Radiation Pattern Omnidirectional Polarization Linear Weight (approx.) 0.11 g. Temperature -40 to +125 ºC Impedance 50  Dimensions (L x W x H) 7.0 mm x 3.0 mm x 2.0 mm Technical features. Measures from the evaluation board (80 mm x 40 mm x 1 mm). 2.3 BLUETOOTH SOLUTION (1-port) Technical features 2400 MHz – 2500 MHz Average Efficiency > 70 % Peak Gain 1.8 dBi VSWR < 2.5:1 Radiation Pattern Omnidirectional Polarization Linear Weight (approx.) 0.11 g. Temperature -40 to +125 ºC Impedance 50  Dimensions (L x W x H) 7.0 mm x 3.0 mm x 2.0 mm Technical features. Measures from the evaluation board (80 mm x 40 mm x 1 mm). Last Update: April 2024 DATASHEET DUO mXTEND TM (NN03-320) 2.4 5G SOLUTION (1-port) Technical features 3.4 – 3.8 GHz Average Efficiency > 60% Peak Gain 2.6 dBi VSWR < 3.0:1 Radiation Pattern Omnidirectional Polarization Linear Weight (approx.) 0.11 g. Temperature -40 to + 125 ºC Impedance 50  Dimensions (L x W x H) 7.0 mm x 3.0 mm x 2.0 mm Technical features. Measures from the evaluation board (80 mm x 40 mm x 1 mm). 2.5 UWB SOLUTION (1-port) Technical features Option 1 UWB (LFR) Option 2 UWB (HFR) 3.1 – 4.8 GHz 6.0 – 10.6 GHz Average Efficiency > 80% > 80% Peak Gain 2.3 dBi 3.6 dBi VSWR < 2.6:1 < 4.0:1 Radiation Pattern Omnidirectional Polarization Linear Weight (approx.) 0.11 g. Temperature -40 to + 125 ºC Impedance 50  Dimensions (L x W x H) 7.0 mm x 3.0 mm x 2.0 mm Technical features. Measures from the evaluation board (25 mm x 20 mm x 1 mm). Last Update: April 2024 DATASHEET DUO mXTEND TM (NN03-320) 2.6 WIFI DUAL BAND SOLUTION (1-port) Technical features 2.4 – 2.5 GHz 4.9 – 5.875 GHz Average Efficiency > 65% > 65% Peak Gain 4.1 dBi 3.8 dBi VSWR < 2.0:1 < 3.0:1 Radiation Pattern Omnidirectional Polarization Linear Weight (approx.) 0.11 g. Temperature -40 to + 125 ºC Impedance 50  Dimensions (L x W x H) 7.0 mm x 3.0 mm x 2.0 mm Technical features. Measures from the evaluation board (80 mm x 40 mm x 1 mm). Last Update: April 2024 DATASHEET DUO mXTEND TM (NN03-320) 2.7 ANTENNA FOOTPRINT: 1 PORT IN THE MIDDLE WITH SLOT CONFIGURATION Measure mm A 1.0 B 2.0 C 2.25 D 1.5 E 1.25 F 2.2 G 0.5 Tolerance: ±0.05mm Footprint dimensions for the DUO mXTEND TM (NN03-320) antenna booster. Pin 1: Mounting pad. This pad is not grounded. Pin 2: Grounding pad. Pin 3: Feeding pad. Pin 4: Open pad. Last Update: April 2024 DATASHEET DUO mXTEND TM (NN03-320) 2.8 ANTENNA FOOTPRINT: 1 PORT IN THE MIDDLE WITH MONOPOLE CONFIGURATION Measure mm A 1.0 B 2.2 C 0.5 D 1.5 E 1.25 F 0.5 Tolerance: ±0.05mm Footprint dimensions for the DUO mXTEND TM (NN03-320) antenna booster. Pin 1: Mounting pad. This pad is not grounded. Pin 2: Open. Pin 3: Open. Pin 4: Feeding pad. Last Update: April 2024 DATASHEET DUO mXTEND TM (NN03-320) 2.9 ANTENNA FOOTPRINT: 2 PORTS IN THE MIDDLE Measure mm A 1.0 B 2.0 C 2.25 D 1.5 E 1.25 F 2.2 G 0.5 Tolerance: ±0.05mm Footprint dimensions for the DUO mXTEND TM (NN03-320) antenna booster. Pin 1: Mounting pad. This pad is not grounded. Pin 2: Grounding pad. Pin 3: Slot Feeding pad PORT 1. Pin 4: Monopole Feeding pad PORT 2. Last Update: April 2024 DATASHEET DUO mXTEND TM (NN03-320) 2.10 ANTENNA FOOTPRINT: 1 PORT IN THE CORNER Measure mm A 1.0 B 3.0 C 1.25 D 1.5 E 7.0 F 0.5 Tolerance: ±0.05mm Footprint dimensions for the DUO mXTEND™ (NN03-320) antenna booster placed on the corner. If you are designing a device with a different size or operating frequency than shown above, you can assess the performance of this configuration using our free-of-charge Oxion™ platform. This platform provides a complete de…

Text truncated - open the document above for the full version.

Test Report No.: G0M-2509-3304-TFC093LP01-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 1 of 15 RF-EXPOSURE REPORT FCC 47 CFR Part 2.1093 RF-Exposure evaluation of portable equipment Report Reference No G0M-2509-3304-TFC093LP01-V01 Testing Laboratory Eurofins Product Service GmbH Address Storkower Str. 38c 15526 Reichenwalde Germany Accreditation DAkkS - Registration number : D-PL-12092-01-00 FCC Filed Test Laboratory, Reg.-No.: 96970 Applicant ASSA ABLOY Sicherheitstechnik GmbH Address Goerzallee 299 14167 Berlin GERMANY Test Specification According to FCC rules Standard FCC 47 CFR 2.1093 Non-Standard Test Method None Equipment under Test (EUT): Product Description CLIQ remote programming device Model(s) CLIQ Connect mobile PD Brand Name(s) None Hardware Version(s) 4 Software Version(s) 3.0 FCC-ID 2BVSN-MBM2BLE Test Result PASSED Test Report No.: G0M-2509-3304-TFC093LP01-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 2 of 15 Possible test case verdicts: required by standard but not tested N/T not required by standard N/R test object does meet the requirement P(PASS) test object does not meet the requirement F(FAIL) Testing: Test Lab Temperature 20 °C - 30 °C Test Lab Humidity 25 % - 55 % Date of performance 2026-03-18 Date of receipt of test item See test sample identification table on page 7 Report: Compiled by Azamat Ibraimov Tested by (+ signature) (Responsible for Test) Azamat Ibraimov ....................................................... Approved by (+ signature) (Senior Radio Expert) Radwan Jaafar ....................................................... Date of Issue 2026-05-29 Total number of pages 15 General Remarks: The test results presented in this report relate only to the object tested. The results contained in this report reflect the results for this particular model and serial number. It is the responsibility of the manufacturer to ensure that all production models meet the intent of the requirements detailed within this report. This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory. The above equipment has been tested by Eurofins Product Service GmbH, and found compliance with the requirements of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Compliance of electromagnetic emission from electronic and electrical equipment with the basic restrictions usually is determined by measurements and, in some cases, calculation of the exposure level. If the electrical power used by or radiated by the equipment is sufficiently low, the electromagnetic fields emitted will be incapable of producing exposures that exceed the basic restrictions. Any relevant compliance assessment procedure which is consistent with the state of the art, reproducible and gives valid results can be used. Test Report No.: G0M-2509-3304-TFC093LP01-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 3 of 15 For transmitters intended for use with more than one antenna configuration option, the combination of transmitter and antenna(s) which generates the highest available antenna power and/or average total radiated power shall be assessed. Additional Comments: RF-Exposure calculation is based on measurement results from reference documents. Test Report No.: G0M-2509-3304-TFC093LP01-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 4 of 15 VERSION HISTORY Version History Version Issue Date Remarks Revised By 01 2026-05-29 Initial Release -- Test Report No.: G0M-2509-3304-TFC093LP01-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 5 of 15 ABBREVIATIONS AND ACRONYMS Acronyms Acronym Description EIRP Equivalent Isotropic Radiated Power ERP Effective Radiated Power EUT Equipment Under Test LPE Low Power Exclusion Test Report No.: G0M-2509-3304-TFC093LP01-V01 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 6 of 15 REPORT INDEX 1 Equipment (Test Item) Under Test................................................................................................... 7 1.1 Reference Documents ................................................................................................................................... 8 1.2 Standalone radiation sources ........................................................................................................................ 9 1.3 Concurrent Sources ...................................................................................................................................... 9 2 Result Summary ............................................................................................................................... 10 3 RF-Exposure classification ............................................................................................................ 11 4 RF-Exposure limits and exclusion thresholds ............................................................................ 12 4.1 SAR limits .................................................................................................................................................... 12 4.2 SAR standalone test exclusion threshold .................................................................................................... 12 4.3 SAR concurrent test exclusion threshold ..................................................................................................... 13 5 RF-Exposure Evaluation ................................................................................................................. 14 6 Single Source Evaluation Results - FCC .........................................................…

Text truncated - open the document above for the full version.

Test Report No.: G0M-2509-3304-EF0115B-V022 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 1 of 27 EMC TEST REPORT FCC CFR Title 47 / Chapter I / Subchapter A / Part 15 / Subpart B ISED ICES-003 Issue 7 Report Reference No G0M-2509-3304-EF0115B-V02 Testing Laboratory Eurofins Product Service GmbH Address Storkower Str. 38c 15526 Reichenwalde Germany Accreditation ISED testing laboratory: CN 3470A FCC Filed Test Laboratory, Reg.-No.: 96970 Applicant ASSA ABLOY Sicherheitstechnik GmbH Address Goerzallee 299 14167 Berlin GERMANY Test Specification Standard(s) FCC CFR Title 47 / Chapter I / Subchapter A / Part 15 / Subpart B ISED ICES-Gen Issue 2 ISED ICES-003 Issue 7 ANSI C63.4:2014+A1:2017 Equipment under Test (EUT): Product Description CLIQ remote programming device Model(s) CLIQ Connect mobile PD Brand Name(s) None Hardware Version(s) 4 Software Version(s) 3.0 FCC ID 2BVSN-MBM2BLE IC 35494-MBM2BLE Test Result PASSED Test Report No.: G0M-2509-3304-EF0115B-V022 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 2 of 27 Possible test case verdicts: required by standard but not tested N/T not required by standard N/R required by standard but not appl. to test object N/A test object does meet the requirement P(PASS) test object does not meet the requirement F(FAIL) Testing: Date of receipt of test item 2026-03-13 Report: Compiled by Matthias Handrik Tested by (+ signature) (Responsible for Test) Matthias Handrik Approved by (+ signature) (Head of Lab) Stephan Liebich Date of Issue 2026-05-28 Total number of pages 27 General Remarks: 1. The above equipment has been tested by Eurofins Product Service GmbH, and found compliance with the requirements set forth in the technical standards mentioned above. The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. 2. The test results are valid only for samples provided by customers and under the test conditions described in this report. 3. This report shall not be reproduced except in full, without the written approval of Eurofins Product Service GmbH. 4. The relevant information is provided by customer in this test report. According to the correctness, appropriateness or co…

Text truncated - open the document above for the full version.