2BVXV-P1BE04Peplink Pepwave Wireless Product

29.2 Traceroute Test The traceroute test tool traces the routing path to the destination through a particular Ethernet interface or a SpeedFusion TM connection. The traceroute test utility is located at System > Tools > Traceroute. Tip A system administrator can use the traceroute utility to analyze the connection path of a LAN/WAN connection. 29.3 Wake-on-LAN Pepwane routers can send special “magic packets” to any client specified from the Web UI. To access this feature, navigate to System > Tools > Wake-on-LAN Select a client from the drop-down list and click Send to send a “magic packet” https://www.peplink.com 229 Copyright @ 2026 Peplink 29.4 WAN Analysis The WAN Analysis feature allows you to run a WAN to WAN speed test between 2 Peplink devices . You can set a device up as a Server or a Client. One device must be set up as a server to run the speed tests and the server must have a public IP address. The default port is 6000 and can be changed if required. The IP address of the WAN interface will be shown in the WAN Connection Status section. https://www.peplink.com 230 Copyright @ 2026 Peplink The client side has a few more settings that can be changed. Make sure that the Control Port matches what’s been entered on the server side. Select the WAN(s) that will be used for testing and enter the Servers WAN IP address. Once all of the options have been set, click the Start Test button. https://www.peplink.com 231 Copyright @ 2026 Peplink The test output will show the Data Streams Parameters, the Throughput as a graph, and the Results. The test can be run again once it’s complete by clicking the Start button or you can click Close and change the parameters for the test. https://www.peplink.com 232 Copyright @ 2026 Peplink 29.5 CLI (Command Line Support) The CLI (Command Line Interface) can be accessed via SSH. You can use it to get device statistics and basic operations. CLI Connect Method: CLI (System > Admin Security): CLI: https://www.peplink.com 233 Copyright @ 2026 Peplink Visit this link for full command set. 29.6 Storage Manager *This page is only available on device with Edge computing features. Kindly refer the link below to further check if the device is able to support edge computing. https://www.peplink.com/compare/routers/ https://www.peplink.com 234 Copyright @ 2026 Peplink This page allow user to configure or format partition of internal storage for MediaFast / ContentHub / Docker Usage. 29.7 External Storage (inlcuded in B One user manual - https://manual.peplink.com/peplink-b-one-series-user-manual/#4245) *This page is only available on device with “External Storage via USB Port”. Kindly refer the link below to further check if the device is able to support External Storage and enable edge computing (Docker). https://www.peplink.com/compare/routers/ This page allow user to manage their USB storage that connected to the device. 29.8 Package Manager *This page is only available on device with Edge computing features. Kindly refer the link below to further check if the device is able to support edge computing. https://www.peplink.com/compare/routers/ This page allow users to manage supported framework that is needed for ContentHub. For more information on how to upload content to the Content Hub, kindly refer (MAX - Chapter 18, Balance - Chapter 12 > Edge Computing). https://www.peplink.com 235 Copyright @ 2026 Peplink 30 Status 30.1 Device System information is located at Status > Device. System Information Device Name This is the name specified in the Device Name field located at System > Admin Security. Model This shows the model name and number of this device. Product Code If your model uses a product code, it will appear here. https://www.peplink.com 236 Copyright @ 2026 Peplink Hardware Revision This shows the hardware version of this device. Serial Number This shows the serial number of this device. Firmware This shows the firmware version this device is currently running. Care Plan Display care plan status and expiry date. Note: Refresh button to manually refresh the PrimeCare license. User who has disabled InControl management may click [Refresh] option to check the PrimeCare license status after a renewal. SpeedFusion VPN Version This shows the current SpeedFusion VPN version. InControl Managed Configuration InControl Managed Configurations (firmware, VLAN, Captive Portal, etcetera) Host Name The host name assigned to the Peplink router appears here. Uptime This shows the length of time since the device has been rebooted. System Time This shows the current system time. OpenVPN Client Profile Link to download OpenVpn Client profile when this is enabled in Remote User Access Diagnostic Report The Download link is for exporting a diagnostic report file required for system investigation. Remote Assistance This option is to Turn on remote assistance with the time duration. The second table shows the MAC address of each LAN/WAN interface connected. To view your device’s End User License Agreement (EULA), click Legal. status https://www.peplink.com 237 Copyright @ 2026 Peplink 30.2 GPS Data GPS enabled models automatically store up to seven days of GPS location data in GPS eXchange format (GPX). To review this data using third-party applications, click Status > Device and then download your GPX file. The Peplink GPS enabled devices export real-time location data in NMEA format through the LAN IP address at TCP port 60660. It is accessible from the LAN or over a SpeedFusion connection. To access the data via a virtual serial port, install a virtual serial port driver. Visit http://www.peplink.com/index.php?view=faq&id=294 to download the driver. https://www.peplink.com 238 Copyright @ 2026 Peplink 30.3 Active Sessions Information on active sessions can be found at Status > Active Sessions > Overview. This screen displays the number of sessions initiated by each application. Click on each service listing for additional information. This screen also indicates the number …

Text truncated - open the document above for the full version.

Client Signal Strength Threshold This field determines that maximum signal strength each individual client will receive. The measurement unit is megawatts. Max number of Clients This field determines the maximum clients that can be connected to APs under this profile. Management VLAN ID This field specifies the VLAN ID to tag to management traffic, such as AP to AP controller communication traffic. The value is 0 by default, meaning that no VLAN tagging will be applied. Note: change this value with caution as alterations may result in loss of connection to the AP controller. Discover Nearby Networks A This option is to turn on and off to scan the nearby the AP. Note: Feature will be automatically turned on with Auto Channel / Dynamic Output Power Beacon Rate A This drop-down menu provides the option to send beacons in different transmit bit rates. The bit rates are 1Mbps, 2Mbps, 5.5Mbps, 6Mbps, and 11Mbps. Beacon Interval A This drop-down menu provides the option to set the time between each beacon send. Available options are 100ms, 250ms, and 500ms. DTIM A This field provides the option to set the frequency for beacon to include delivery traffic indication message (DTIM). The interval unit is measured in milliseconds. RTS Threshold A This field provides the option to set the minimum packet size for the unit to send an RTS using the RTS/CTS handshake. Setting 0 disables this feature. Fragmentation Threshold A Determines the maximum size (in bytes) that each packet fragment will be broken down into. Set 0 to disable fragmentation. Distance/Time Converter A Select the distance you want your Wi-Fi to cover in order to adjust the below parameters. Default values are recommended. Slot Time A This field provides the option to modify the unit wait time before it transmits. The default value is 9μs. ACK Timeout A This field provides the option to set the wait time to receive acknowledgement packet before doing retransmission. The default value is 48μs. A - Advanced feature. Click the button on the top right-hand corner to activate. Important Note Per FCC regulation, the country selection is not available on all models marketed in the US. All US models are fixed to US channels only. https://www.peplink.com 186 Copyright @ 2026 Peplink The device with integrated AP can operate under the Wi-Fi Operating Mode, and the default setting is WAN + AP mode: Note: This option is available for selected devices only (HD2/HD4 and HD2/HD4 MBX). Integrated AP WAN In this mode, all Wi-Fi will operate as Wi-Fi WAN and no integrated Wi-Fi AP will be operated on this device. If Wi-Fi Operating mode is choosing WAN, The status indicated by the front panel LED is as follows: - Wi-Fi 1 is Green if Wi-Fi WAN 1 is enabled. - Wi-Fi 2 is Green if Wi-Fi WAN 2 is enabled. WAN + AP In this mode, some Wi-Fi will operate as Wi-Fi WAN. Some other Wi-Fi WANs will be forced offline and their Wi-Fi resources will be reserved for integrated Wi-Fi AP operations. If Wi-Fi Operating mode is choosing WAN + AP, The status indicated by the front panel LED is as follows: - Wi-Fi 1 is Green if WI-FI WAN is enabled. - Wi-Fi 2 is Green if Wi-Fi AP is ON. AP In this mode, all Wi-Fi functions as integrated Wi-Fi AP. All Wi-Fi WANs will be forced to go offline. If Wi-Fi Operating mode is choosing AP, The status indicated by the front panel LED is as follows: - W-Fi 1 is Green, if there is any Wireless SSID is selected 2.4GHz. - W-Fi 2 is Green, if there is any Wireless SSID is selected 5GHz. https://www.peplink.com 187 Copyright @ 2026 Peplink Web Administration Settings (on External AP) Enable Check the box to allow the Peplink router to manage the web admin access information of the AP. Web Access Protocol These buttons specify the web access protocol used for accessing the web admin of the AP. The two available options are HTTP and HTTPS. Management Port This field specifies the management port used for accessing the device. HTTP to HTTPS Redirection This option will be available if you have chosen HTTPS as the Web Access Protocol. With this enabled, any HTTP access to the web admin will redirect to HTTPS automatically. Admin User Name This field specifies the administrator username of the web admin. It is set as admin by default. Admin Password This field allows you to specify a new administrator password. You may also click the Generate button and let the system generate a random password automatically. This allows users to configure AP Time Settings (both Timezone and NTP) in AP Controller. AP Time Settings Time Zone This field is to select the time zone for the AP controller. Time Server This field is to select the time server for the AP controller. This settings is to allow user to manage external AP's controller unreachable action. When Manage Unreachable Action is checked, there will have 2 options which are "None" and "Radio Off". https://www.peplink.com 188 Copyright @ 2026 Peplink This is an option to enable client load balancing for AP Controller. When the option is enabled, it is trying to balance the station count on APs within the same profile. Some Peplink models displays a screen similar to the one shown below, navigating to AP > Settings: Wi-Fi Radio Settings Operating Country This option sets the country whose regulations the Peplink router follows. Wi-Fi Antenna Wi-Fi Antenna Choose from the router's internal or optional external antennas, if so equipped. Wi-Fi AP Settings Protocol This option allows you to specify whether 802.11b and/or 802.11g client association requests will be accepted. Available options are 802.11ng and 802.11na. By default, 802.11ng is selected. https://www.peplink.com 189 Copyright @ 2026 Peplink Channel This option allows you to select which 802.11 RF channel will be used. Channel 1 (2.412 GHz) is selected by default. Channel Width Auto (20/40 MHz) and 20 MHz are available. The default setting is Auto (20/40 MHz), which allows both widths to be used simultaneously. Output Power This option is for s…

Text truncated - open the document above for the full version.

OSPF Settings Area ID Assign a name to be applied to this group. Machines linked to this group will send and receive related OSPF packets, while unlinked machines will ignore them. Link Type Choose the type of network that this area will use. Authentication If an authentication method is used, select one from this drop-down menu. Available options are MD5 and Text. Authentication key(s) may be input next to the drop-down menu after selecting an authentication method. Interfaces Select the interface(s) that this area will use to listen to and deliver OSPF packets. To access RIPv2 settings, click on . https://www.peplink.com 137 Copyright @ 2026 Peplink RIPv2 Settings Authentication If an authentication method is used, select one from this drop-down menu. Available options are MD5 and Text. Authentication key(s) may be input next to the drop-down menu after selecting an authentication method. Interfaces Select the interface(s) that this area will use to listen to and deliver RIPv2 packets. OSPF & RIPv2 Route Advertisement SpeedFusion VPN Route Isolation Isolate SpeedFusion VPN peers from each other. Received SpeedFusion VPN routes will not be forwarded to other SpeedFusion VPN peers to reduce bandwidth consumption.. Network Advertising Networks to be advertised over OSPF & RIPv2. If no network is selected, all LAN / VLAN networks will be advertised by default. Static Route Advertising Enabling OSPF & RIPv2 Route Advertising allows it to advertise LAN static routes over OSPF & RIPv2. Static routes on the Excluded Networks table will not be advertised. 21.2 BGP Click the Advanced tab along the top bar, and then click the BGP item on the sidebar to configure BGP. Click the "x" to delete a BGP profile. Click "Add" to create a new BGP profile. https://www.peplink.com 138 Copyright @ 2026 Peplink BGP Profile Name This field specifies the name that represents this profile. Enable When this box is checked, this BGP profile will be enabled. If it is left unchecked, it will be disabled. Interface The interface in which the BGP neighbor is located. Router ID This field specifies the unique IP as the identifier of the local device running BGP. Autonomous System The Autonomous System Number (ASN) assigned to this profile. Neighbor BGP Neighbors and their details. IP address The IP address of the Neighbor. Autonomous System The Neighbor's ASN. Multihop/TTL This field determines the Time-to-live (TTL) of BGP packets. Leave this field blank if the BGP neighbor is directly connected, otherwise you must specify a TTL value. This option should be used if the configured Neighbor’s IP address does not match the selected Interface’s network subnets. The TTL value must be between 2 to 255. Password (Optional) Assign a password for MD5 authentication of BGP sessions. AS-Path Prepending: AS path to be prepended to the routes received from this Neighbor. Values must be ASN and separated by commas. For example: inputting "64530,64531" will prepend "64530, 64531" to received https://www.peplink.com 139 Copyright @ 2026 Peplink routes. Hold Time Wait time in seconds for a keepalive message from a Neighbor before considering the BGP connection as stalled. The value must be either 0 (infinite hold time) or between 3 and 65535 inclusively. Default: 240 Next Hop Self Enable this option to advertise your own source address as the next hop when propagating routes. iBGP Local Preference This is the metric advertised to iBGP Neighbors to indicate the preference for external routes. The value must be between 0 to 4294967295 inclusively. Default: 100 BFD Enable this option to add Bidirectional Forwarding Detection for path failure. All directly connected Neighbors that use the same physical interface share the same BFD settings. All mulithop Neighbors share the same multihop BFD settings. You can configure BFD settings in the BGP profile listing page after this option is enabled. Network Advertising Select the Networks that will be advertised to the BGP Neighbor. Static Route Advertising Enable this option to advertise static LAN routes. Static routes that match the Excluded Networks table will not be advertised. Custom Route Advertising Additional routes to be advertised to the BGP Neighbor. Advertise OSPF Route When this box is checked, every learnt OSPF route will be advertised. Set Community Assign a prefix to a Community. https://www.peplink.com 140 Copyright @ 2026 Peplink Community: Two numbers in new-format. e.g. 65000:21344 Well-known communities: no-export 65535:65281 no-advertise 65535:65282 no-export-subconfed 65535:65283 no-peer 65535:65284 Route Prefix: Comma separated networks. e.g. 172.168.1.0/24,192.168.1.0/28 Filter Mode This field allows for the selection of the filter mode for route import. None: All BGP routes will be accepted. Accept: Routes in "Restricted Networks" will be accepted, routes not in the list will be rejected. Reject: Routes in "Blocked Networks" will be rejected, routes not in the list will be accepted. Restricted Networks / Blocked Networks This field specifies the network(s) in the “route import” entry. Exact Match: When this box is checked, only routes with the same Network and Subnet Mask will be filtered. Otherwise, routes within the Networks and Subnets will be filtered. Filter Mode This field allows for the selection of the filter mode for route export. https://www.peplink.com 141 Copyright @ 2026 Peplink None: All BGP routes will be accepted. Accept: Routes in "Restricted Networks" will be accepted, routes not in the list will be rejected. Reject: Routes in "Blocked Networks" will be rejected, routes not in the list will be accepted. Restricted Networks / Blocked Networks This field specifies the network(s) in the “route export” entry. Exact Match: When this box is checked, only routes with the same Network and Subnet Mask will be filtered. Otherwise, routes within the Networks and Subnets will be filtered. Export to other BGP Profile When this box is checked, routes learnt from this…

Text truncated - open the document above for the full version.

authentication. Mode Choose Main Mode if both IPsec peers use static IP addresses. Choose Aggressive Mode if one of the IPsec peers uses dynamic IP addresses. Force UDP Encapsulation For forced UDP encapsulation regardless of NAT-traversal, tick this checkbox. Pre-shared Key This defines the peer authentication pre-shared key used to authenticate this VPN connection. The connection will be up only if the pre-shared keys on each side match. Remote Certificate (pem encoded) Available only when X.509 Certificate is chosen as the Authentication method, this field allows you to paste a valid X.509 certificate. Local ID In Main Mode, this field can be left blank. In Aggressive Mode, if Remote Gateway IP Address is filled on this end and the peer end, this field can be left blank. Otherwise, this field is typically a U-FQDN. Remote ID In Main Mode, this field can be left blank. In Aggressive Mode, if Remote Gateway IP Address is filled on this end and the peer end, this field can be left blank. Otherwise, this field is typically a U-FQDN. Phase 1 (IKE) Proposal In Main Mode, this allows setting up to six encryption standards, in descending order of priority, to be used in initial connection key negotiations. In Aggressive Mode, only one selection is permitted. Phase 1 DH Group This is the Diffie-Hellman group used within IKE. This allows two parties to establish a shared secret over an insecure communications channel. The larger the group number, the higher the security. Group 2: 1024-bit is the default value. Group 5: 1536-bit is the alternative option. Phase 1 SA Lifetime This setting specifies the lifetime limit of this Phase 1 Security Association. By default, it is set at 3600 seconds. Phase 2 (ESP) Proposal In Main Mode, this allows setting up to six encryption standards, in descending order of priority, to be used for the IP data that is being transferred. In Aggressive Mode, only one selection is permitted. Phase 2 PFS Group Perfect forward secrecy (PFS) ensures that if a key was compromised, the attacker will be able to access only the data protected by that key. None - Do not request for PFS when initiating connection. However, since there is no valid reason to refuse PFS, the system will allow the connection to use PFS if requested by the remote peer. This is the default value. Group 2: 1024-bit Diffie-Hellman group. The larger the group number, the higher the security. Group 5: 1536-bit is the third option. https://www.peplink.com 91 Copyright @ 2026 Peplink Phase 2 SA Lifetime This setting specifies the lifetime limit of this Phase 2 Security Association. By default, it is set at 28800 seconds. WAN Connection Priority WAN Connection Select the appropriate WAN connection from the drop-down menu. IPsec Settings DPD Interval Time interval between Dead Peer Detection (DPD) messages (R_U_THERE in IKEv1 or INFORMATIONAL in IKEv2) that check if the peer is still active when no other traffic is present. Default: 10 seconds (2–30 seconds) DPD Attempts Total number of DPD messages sent before the peer is considered unreachable. Default: 3 times (2-10 times) 11 GRE Tunnel Generic Routing Encapsulation (GRE) is a tunneling protocol that can encapsulate a wide variety of network layer protocols inside virtual point-to-point links over an Internet Protocol network. A GRE tunnel is similar to IPSec or SpeedFusion VPN. To configure a GRE Tunnel, navigate to Advanced > GRE Tunnel. Click the New Profile button to create new GRE tunnel profiles that establish tunnel connections to remote tunnel endpoints via available WAN connections. To edit the profiles, click on its associated connection name in the leftmost column. https://www.peplink.com 92 Copyright @ 2026 Peplink GRE Tunnel Profile Settings Name This field is for specifying a name to represent this GRE Tunnel connection profile. Active When this box is checked, this GRE Tunnel connection profile will be enabled. Otherwise, it will be disabled. Remote GRE IP Address This field is for entering the remote GRE’s IP address Tunnel Local IP Address This field is for specifying the tunnel source IP address. Tunnel Remote IP Address This field is for specifying the tunnel destination IP address Tunnel Subnet Mask This field is to select the subnet mask that is to be used for the GRE tunnel. Connection Select the appropriate WAN connection from the drop-down menu. Remote Networks Input the LAN and subnets that are located at the remote site here. https://www.peplink.com 93 Copyright @ 2026 Peplink 12 OpenVPN OpenVPN is a site to site VPN mode that can encapsulate a wide variety of network layer protocols inside virtual point-to-point links over an Internet Protocol network. To configure a OpenVPN, navigate to Advanced > OpenVPN and click the New Profile. OpenVPN Profile Settings Name This field is for specifying a name to represent this OpenVPN profile. Active When this box is checked, this OpenVPN connection profile will be enabled. Otherwise, it will be disabled. OpenVPN Profile Upload the OpenVPN configuration (.ovpn) file from your service provider. Login Credential (Optional) This option is an optional for you to enter the username and password to login for the OpenVPN connection if the profile need to login. Connection Select the appropriate WAN connection from the drop-down menu. https://www.peplink.com 94 Copyright @ 2026 Peplink 13 Outbound Policy Peplink routers can flexibly manage and load balance outbound traffic among WAN connections. Important Note Outbound policy is applied only when more than one WAN connection is active. The settings for managing and load balancing outbound traffic are located at Advanced > Outbound Policy. 13.1 Adding Rules for Outbound Policy The menu underneath enables you to define Outbound policy rules: The bottom-most rule is Default. Edit this rule to change the device’s default manner of controlling outbound traffic for all connections that do not match any of the rules above it. Under the Service heading, clic…

Text truncated - open the document above for the full version.

Drop-in Mode Settings Enable Drop-in mode eases the installation of the Peplink MAX on a live network between the existing firewall and router, such that no configuration changes are required on existing equipment. Check the box to enable the drop-in mode feature. WAN for Drop-In Mode Select the WAN port to be used for drop-in mode. If WAN is selected, the high availability feature will be disabled automatically. Shared Drop-In IP A When this option is enabled, the passthrough IP address will be used to connect to WAN hosts (email notification, remote syslog, etc.). The MAX will listen for this IP address when WAN hosts access services provided by the MAX (web admin access from the WAN, DNS server requests, etc.). To connect to hosts on the LAN (email notification, remote syslog, etc.), the default gateway address will be used. The MAX will listen for this IP address when LAN hosts access services provided by the MAX (web admin access from the WAN, DNS proxy, etc.). https://www.peplink.com 45 Copyright @ 2026 Peplink Shared IP Address A Access to this IP address will be passed through to the LAN port if this device is not serving the service being accessed. The shared IP address will be used in connecting to hosts on the WAN (e.g., email notification, remote syslog, etc.) The device will also listen on the IP address when hosts on the WAN access services served on this device (e.g., web admin accesses from WAN, DNS server, etc.) WAN Default Gateway Enter the WAN router's IP address in this field. If there are more hosts in addition to the router on the WAN segment, click the button next to “WAN Default Gateway” and check the other host(s) on the WAN segment box and enter the IP address of the hosts that need to access LAN devices or be accessed by others. WAN DNS Servers Enter the selected WAN's corresponding DNS server IP addresses. A - Advanced feature, please click the button on the top right-hand corner to activate. 7.2 Port Settings To configure port settings, navigate to Network > Port Settings On this screen, you can enable specific ports, as well as determine the speed of the LAN ports, whether each port is a trunk or access port, as well as which VLAN each link belongs to, if any. Untagged frames received by the port are classified to a VLAN indicated by Port VLAN Identifier (PVID). All frames from the VLAN are untagged on egress.PVID option is only configurable when Port Type is set to “Trunk”. https://www.peplink.com 46 Copyright @ 2026 Peplink 7.3 Captive Portal The captive portal serves as a gateway that clients have to pass if they wish to access the internet using your router. To configure, navigate to Network > LAN > Captive Portal. Captive Portal Settings Name Enter the name for the Captive Portal. Enable Check Enable and then, optionally, select the LANs/VLANs that will use the captive portal. Hostname To customize the portal’s form submission and redirection URL, enter a new URL in this field. To reset the URL to factory settings, click Default. https://www.peplink.com 47 Copyright @ 2026 Peplink Access Mode Click Open Access to allow clients to freely access your router. Click User Authentication to force your clients to authenticate before accessing your router. Select External Server to use the Captive Portal with a HotSpot system. As described in the following knowledgebase article: https://forum.peplink.com/t/using-hotspotsystem-wi-fi-on-Peplink-max-routers/ Authentication When selecting the “User Authentication” in the Access Mode field, you will see the available option for the Authentication via drop-down list: ● RADIUS Server ● LDAP Server Fill in the necessary information to complete your connection to the server and enable authentication. External Server When selecting the “External Server” in the Access Mode field, you will see the available option for the Service Type via drop-down list: ● CoovaChilli https://www.peplink.com 48 Copyright @ 2026 Peplink ● HotspotSystem Fill in the necessary information to complete your connection to the server and enable authentication. Access Quota Set a time and data cap to each user’s Internet usage. Quota Reset Time This menu determines how your usage quota resets. Setting it to Daily will reset it at a specified time every day. Setting a number of minutes after quota reached establish a timer for each user that begins after the quota has been reached. Inactive Timeout Clients will get disconnected when the inactive the configured time is reached. Default 0: no timeout Allowed Networks Add networks that can bypass the captive Portal in this field. To whitelist a network, enter the domain name / IP address here and click . To delete an existing network from the list of allowed networks, click the button next to the listing. Allowed Clients Add MAC address and /or IP addresses for client devices that are allowed to bypass the Captive Portal. Clients accessing these domains and IP addresses will not be redirected to the splash page. Splash Page Here, you can choose between using the Peplink router’s built-in captive portal and redirecting clients to a URL you define. Popup Handling Configurable options for popup handling: - Bypass Popup (Redirection only takes place on normal browser) - Automatically show splash page on Safari for Apple (iOS / macOS) devices Logout Hostname A hostname that can be used to logout captive portal when being accessed on browser. Customize splash page Click on the provided link in the Captive portal profile to customize the splash page. A new browser tab is opened with a WYSIWYG editor of the splash page o edit the content, click on the corresponding element after switching Edit Mode to ON. https://www.peplink.com 49 Copyright @ 2026 Peplink https://www.peplink.com 50 Copyright @ 2026 Peplink 8 Con figuring the WAN Interface(s) WAN Interface settings are located at Network > WAN. To reorder WAN priority, drag on the appropriate WAN by holding the left mouse button, move it to the desired priorit…

Text truncated - open the document above for the full version.