2BWB4-V28Integrated follow-up camera with pan tilt and selfie stick

充电电流: 100MA 发射频率: 2.402GHZ-2.480GHZ 适配器充电电压/电流 5V/ 1-3A 适用系统:兼容苹果/安卓/鸿蒙 蓝牙名称: selfie-8 遥控距离: 10米(30英寸) 电池:聚合物电池 (150mAh) 充电接口: Type-C 颜色:黑 夹手机尺寸: 6.5-10cm Applicable system: compatible with Apple /Android/Hongmeng Bluetooth name: selfie-8 Batter y: Polymer batter y (150mAh) Transmission frequency: 2.402GHZ-2.480GHZ Charging interface: Type-C Remote control distance: 10 meters (30 inches) Charging current: 100MA Adapter charging voltage/current 5V/1-3A Clip phone size: 6.5-10cm Color : black 产 品 参 数 遥 控 器 参 数 Product Parameters Remote Controi Parameters 1.长按开机键3秒开机/关机。开机即跟 随，单击暂停/开始跟随。 2.将摄像头调整照到面部，检测到人脸 绿灯常亮，即进入跟随模式。 3.手势功能：手掌手势1秒停止跟随， OK手势1秒恢复跟随。 5.20识别不到人脸，分后自动关机，低 电量时红灯闪烁，一分钟后自动关机。 4.单人模式：耶手势指示灯闪烁后，只 跟优先进摄像头的人，其他人经过只闪 灯不跟随，当云台暂停跟踪后，OK手势 或者单击开关机按键进入多人模式，跟 随最易识别的人，可通过前后站立位置 进行切换。 2. Adjust the camera to focus on the face and detect that the green light on the face is constantly on, then enter the following mode. 4. Single player mode: After the Ye gesture indicator light flashes, only the person with the advanced camera will follow. Other people passing by will only flash the light and not follow. When the gimbal pauses tracking, use the OK gesture or click the power button to enter the multiplayer mode. Follow the most recognizable person and switch between forward and backward standing positions. 3. Gesture function: Palm gesture stops following for 1 second, OK gesture resumes following for 1 second. 5. Unable to recognize face, automatically shuts down after 20 minutes, red light flashes when low battery, automatically shuts down after one minute. 1. Press and hold the power button for 3 seconds to turn on/off the device. Follow immediately upon startup, click pause/start following. 拨动开关机键开关机，LED灯闪烁即已开机蓝灯 然后打开手机的蓝牙选项，搜索设备蓝牙名 为:点击完成配对，显示已连接即完成。selfie-8 连接蓝牙: Toggle the power button to turn on or off the device. When the LED light flashes blue, it indicates that the device has been powered on. Then, enable the Bluetooth option on your mobile phone, search for the device with the Bluetooth name 'selfie-8', click to complete the pairing, and when 'Connected' is displayed, the process is complete. Remote Control: 遥 控 器 操 作 说 明 Remote Controloperation Power on/off photo selfie-8 selfie-8 Remote Controloperation 3.拍照:遥控器与手机处于连接状态时单击拍照 键，指示灯闪烁并拍照。 7.充电时红灯常亮,充满后熄灭,充电电流100MA 4.开机后连接好蓝牙，无操作5分钟，设备进入 的低功耗休眠状态，任意点击操作都可唤醒。 无操作10分钟后断开蓝牙连接，自动关机。 2.蓝牙连接:打开手机蓝牙搜索“selfie-8”点击连 接，连接成功后指示灯熄灭。 1.开机:向上拨动开关机按钮开机,指示灯闪烁进 入搜索状态。 5.关机:向下拨动开关机键,指示灯闪烁熄灭并关 机。 6.重新开机后，蓝牙自动回连正常使用。 6. After restarting, Bluetooth will automatically reconnect and function normally. 2. Bluetooth connection: Open the phone Bluetooth search for "selfie-8" and click on the connection. After successful connection, the indicator light will turn off. 4. After turning on the device, connect Bluetooth and wait for 5 minutes without any operation. The device enters a low-power sleep state and can be awakened by any click. After 10 minutes of inactivity, disconnect the Bluetooth connection and automatically shut down. 7. The red light is always on during charging, but goes out when fully charged, with a charging current of 100MA 1. Power on:Slide the power button upward to turn on the device. The indicator light flashes as it enters search mode. 3. Take a photo: When the remote control is connected to the phone, click the take photo button, and the indicator light will flash and take a photo. 5. Shutdown: Slide the power button down, and the indicator light will flash and then turn off, powering the device down. 1:打开相机进入拍照界面。2:向左滑动或者找 到相机设置。3:点击音量键功能。4:将音量键 功能设置为快门(不要选缩放或者对焦)。5:个 别手机相机设置路径不同,请自行查找 关于安卓系统手机个别出现按遥控器为加音 量/调焦距/或无反应的问题的解决方案 A Solution to the Problem of Individually Pressing the Remote Control to Increase Volume/Adjust Focus/or Not Responding on Android System Mobile Phones 1: Open the camera to enter the photography interface. 2: Swipe left or find the camera settings. 3: Click on the volume button function. 4: Set the volume key function to shutter (do not select zoom or focus). 5: Individual mobile camera settings have different paths, please search for them yourself 遥 控 器 操 作 说 明 Remote Controloperation FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may caus e undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

Rev 1/26/2023 Yuyao Zhenguan Photography Equipment Co., Ltd Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2026/6/9 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: 2BWB4-V28 Applicant FRN: 0038473039 [Yuyao Zhenguan Photography Equipment Co., Ltd] certifies that, as of the date of the filing of the application, [FCC US Agent, LLC] is our designated U.S. agent for service of process for the above referenced FCC ID. [Yuyao Zhenguan Photography Equipment Co., Ltd] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. [FCC US Agent, LLC] accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Company Name: FCC US Agent, LLC FRN: 0033402884 Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Contact Person: Tim Payne Phone: 708-571-3148 Email: [email protected] Sincerely,

Yuyao Zhenguan Photography Equipment Co., Ltd 2.911 (d)(5)(i) Equipment Type Attestation v1.2 Section 2.911(d)(5)(i) Certification – Equipment Type Company name: Yuyao Zhenguan Photography Equipment Co., Ltd Address: No. 99 Yicheng Road, Linshan Town, Yuyao City, Zhejiang Province FCC ID: 2BWB4-V28 Model(s): V28, V18 2.911(d)(5)(i) Equipment Type We, [Yuyao Zhenguan Photography Equipment Co., Ltd] (“the applicant”) certify that the equipment for which authorization is sought through certification is not: • Prohibited from receiving an equipment authorization pursuant to § 2.903; of the FCC rules. • Identified as an equipment type in the “Covered List” NOTE 1 Yours sincerely, Name: Li Yunyu Date: 2026.5.29 Title and Company name: Project Manager / Yuyao Zhenguan Photography Equipment Co., Ltd NOTE 1 “Covered List ”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Yuyao Zhenguan Photography Equipment Co., Ltd 2.911 (d)(5)(ii) Applicant Attestation v1.2 Section 2.911(d)(5)(ii) Certification – Applicant (Covered List ) Company name: Yuyao Zhenguan Photography Equipment Co., Ltd Address: No. 99 Yicheng Road, Linshan Town, Yuyao City, Zhejiang Province FCC ID: 2BWB4-V28 Model(s): V28, V18 2.911(d)(5)(ii) Applicant filing We, [Yuyao Zhenguan Photography Equipment Co., Ltd] (“the applicant”) certify that, as of the date of the filing of the application, the applicant is not identified NOTE 1 on the “Covered List” NOTE 2, established pursuant to § 1.50002 of this chapter, as an entity producing covered communications equipment. Yours sincerely, Name: Li Yunyu Date: 2026.5.29 Title and Company name: Project Manager / Yuyao Zhenguan Photography Equipment Co., Ltd NOTE 1 Delete option not applicable to this application. NOTE 2 “Covered List ”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Yuyao Zhenguan Photography Equipment Co., Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject; Request for Confidentiality FCC ID: 2BWB4-V28 Date: 2026/5/29 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Li Yunyu Title: Project Manager

Yuyao Zhenguan Photography Equipment Co., Ltd Authorization Company: Yuyao Zhenguan Photography Equipment Co., Ltd Address: No. 99 Yicheng Road, Linshan Town, Yuyao City, Zhejiang Province Product Name: Integrated follow-up camera with pan tilt and selfie stick Model Number(s): V28, V18 Product Description: Integrated follow-up camera with pan tilt and selfie stick We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2026/5/29 Name: Li Yunyu Title: Project Manager Company: Yuyao Zhenguan Photography Equipment Co., Ltd

Yuyao Zhenguan Photography Equipment Co., Ltd Model Difference 2026/05/29 EUT NAME: Integrated follow-up camera with pan tilt and selfie stick FCC ID: 2BWB4-V28 MODEL : V28, V18 All the model are the same circuit and RF module, except model names. Sincerely Client’s signature Client’s name / title : Li Yunyu / Project Manager Contact information / address: No. 99 Yicheng Road, Linshan Town, Yuyao City, Zhejiang Province

External Photos

Size:20*10mm FCC ID: 2BWB4-V28 Label location

Internal Photos Antenna

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the ShenZhen STS Test Services Co., Ltd. MPE Report Report No.:STS2603407H01 Issued for Yuyao Zhenguan Photography Equipment Co., Ltd No. 99 Yicheng Road, Linshan Town, Yuyao City, Zhejiang Province Product Name: Integrated follow-up camera with pan tilt and selfie stick Brand Name: N/A Model Name: V28 Series Model(s): V18 FCC ID: 2BWB4-V28 Test Standards: FCC 47CFR §2.1093 Page 2 of 7 Report No.: STS2603407H01 TEST REPORT Applicant’s Name ................. : Yuyao Zhenguan Photography Equipment Co., Ltd Address ................................. : No. 99 Yicheng Road, Linshan Town, Yuyao City, Zhejiang Province Manufacturer's Name ........... : Yuyao Zhenguan Photography Equipment Co., Ltd Address ................................. : No. 99 Yicheng Road, Linshan Town, Yuyao City, Zhejiang Province Product Description Product Name ........................ : Integrated follow-up camera with pan tilt and selfie stick Brand Name .......................... : N/A Model Name .......................... : V28 Series Model(s) ...................... : V18 Test Standards ..................... : FCC 47CFR §2.1093 447498 D01 Interim General RF Exposure Guidance v06 The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the ShenZhen STS Test Services Co., Ltd. Date of Test ........................................... : Date of receipt of test item ...................... : 10 Mar. 2026 Date (s) of performance of tests ............. : 10 Mar. 2026 ~ 28 Apr. 2026 Date of Issue .......................................... : 29 Apr. 2026 Test Result .............................................. : Pass Testing Engineer : (Aaron Bu) Technical Manager : (Skylar Li) Authorized Signatory : (Bovey Yang) Page 3 of 7 Report No.: STS2603407H01 TABLE OF CONTENTS 1. GENERAL INFORMATION 5 1.1 GENERAL DESCRIPTION OF THE EUT 5 1.2 TEST FACTORY 5 2. FCC 47CFR §2.1093 REQUIREMENT 6 2.1 TEST STANDARDS 6 2.2 LIMIT 6 2.3 TEST RESULT 7 Page 4 of 7 Report No.: STS2603407H01 Revision History Rev. Issue Date Report No. Effect Page Contents 00 29 Apr. 2026 STS2603407H01 ALL Initial Issue Page 5 of 7 Report No.: STS2603407H01 1. GENERAL INFORMATION 1.1 GENERAL DESCRIPTION OF THE EUT Product Name Integrated follow-up camera with pan tilt and selfie stick Brand Name N/A Model Name V28 Series Model(s) V18 Model Difference All models are identical except for the model name, the test model is V28. Product Description The EUT is a Integrated follow-up camera with pan tilt and selfie stick. Operation Frequency: 2402~2480 MHz Modulation Type: GFSK Antenna gain: 1.13 dBi Antenna Designation: Internal Antenna Power Rating DC 5V from adapter/ DC 3.7V from battery Adapter N/A Battery DC 3.7V Hardware Version N/A Software Version N/A 1.2 TEST FACTORY SHENZHEN STS TEST SERVICES CO., LTD Add. : 101, Building B, Zhuoke Science Park, No.190 Chongqing Road, ZhanChengShequ, Fuhai Sub-District, Bao’an District, Shenzhen, Guang Dong, China FCC test Firm Registration Number: 625569 IC test Firm Registration Number: 12108A A2LA Certificate No.: 4338.01 Page 6 of 7 Report No.: STS2603407H01 2. FCC 47CFR §2.1093 REQUIREMENT 2.1 TEST STANDARDS The limit for Maximum Permissible Exposure (MPE) specified in KDB 447498 D01 General RF Exposure Guidance v06 is followed. The gain of the antennas used in the product is extracted from the Antenna data sheets provided and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis Transmission formula is far field assumption, the calculated result of that is an over-prediction for near field power density. It is taken as worst case to specify the safety range. 2.2 LIMIT Approximate SAR Test Exclusion Power Thresholds at Selected Frequencies and Test Separation Distances are illustrated in the following Table. Page 7 of 7 Report No.: STS2603407H01 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] • [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,where f(GHz) is the RF channel transmit frequency in GHz. Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2.3 TEST RESULT Maximum measured transmitter power. Worst Case Mode frequency Maximum Output Power Tune up tolerance Max Tune up GHz dBm dBm dBm GFSK(BLE) 2.402 1.27 1±1 2 Evaluation Result Mode Frequency Antenna Distance RF output power including tune up (dBm) SAR Test Exclusion Threshold SAR Test Exclusion Estimated SAR GHz mm dBm mw GFSK(BLE) 2.402 5 2 1.585 0.491 Yes / Note: 1. Remark: The worst case gain of the antenna is 1.13dBi. 2. Threshold at which no SAR required is 0.491≤ 3.0 for 1-g SAR, Separation distance ≤ 5mm. ※※※※※END OF THE REPORT※※※※※

BR19 BR19BR19 BR19- -- -V VV V3 33 3 Antenna describe Antenna describeAntenna describe Antenna describe Antenna plate Monoploe antenna Model name BR19-V3 Antenna gain 1.13dBi Frequecy range 2402MHZ-2480MHZ Connector type Direct Model BR19-V3 Test/Plsition 2D FS Gain Frequency 2402 2441 2480 Ant.Port Input Pwr.(dBm) 0 0 0 Tot.Rad.Pwr.(dBm) -2.28 -0.41 -1.13 Peak EIRP(dBm) -1.73 0.40 0.45 Directivity(dBi) 1.74 1.64 2.44 Efficiency(dB) -4.47 -0.51 -1.34 Gain(dBi) -2.73 1.13 1.10 Front/Back Ratio(dB) 0.82 3.11 4.98 Beamwidth(°) 94.00 126.00 128.00 +Beamwidth(°) 41.00 36.00 39.00 -Beamwidth(°) 53.00 90.00 90.00 Boresight Angle(°) 10.00 240.00 235.00 Maximum Power(dBm) -2.73 1.13 1.10 Minimum Power(dBm) -10.30 -3.38 -4.81 Average Power(dBm) -4.43 -0.50 -1.36 Max/Min Ratio(dB) 7.57 4.51 5.91 Max/Avg Ratio(dB) 1.70 1.63 2.46 Min/Avg Ratio(dB) -5.87 -2.78 -3.45 Average Gain(dB) -4.47 -0.51 -1.34 NOTE

The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Radio Test Report Report No.: STS2603407W01 Issued for Yuyao Zhenguan Photography Equipment Co., Ltd No. 99 Yicheng Road, Linshan Town, Yuyao City, Zhejiang Province Product Name: Integrated follow-up camera with pan tilt and selfie stick Brand Name: N/A Model Name: V28 Series Model(s): V18 FCC ID: 2BWB4-V28 Test Standards: FCC Part15.247 Page 2 of 65 Report No.: STS2603407W01 TEST REPORT Applicant’s Name ................. : Yuyao Zhenguan Photography Equipment Co., Ltd Address ................................. : No. 99 Yicheng Road, Linshan Town, Yuyao City, Zhejiang Province Manufacturer's Name .......... : Yuyao Zhenguan Photography Equipment Co., Ltd Address ................................. : No. 99 Yicheng Road, Linshan Town, Yuyao City, Zhejiang Province Product Description Product Name ....................... : Integrated follow-up camera with pan tilt and selfie stick Brand Name .......................... : N/A Model Name .......................... : ... : V28 Series Model(s) .................... : V18 Test Standards ..................... : FCC Part15.247 Test Procedure ...................... : ANSI C63.10-2020 This device described above has been tested by STS, the test results show that the equipment under test (EUT) is in compliance with the IC requirements. And it is applicable only to the tested sample identified in the report. The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Shenzhen STS Test Services Co., Ltd. Date of Test ........................................... : Date of receipt of test item ..................... : 10 Mar. 2026 Date (s) of performance of tests ............. : 10 Mar. 2026 ~ 28 Apr. 2026 Date of Issue .......................................... : 29 Apr. 2026 Test Result.............................................. : Pass Testing Engineer : (Aaron Bu) Technical Manager : (Skylar Li) Authorized Signatory : (Bovey Yang) Page 3 of 65 Report No.: STS2603407W01 Table of Contents Page 1. SUMMARY OF TEST RESULTS 6 1.1 TEST FACTORY 7 1.2 MEASUREMENT UNCERTAINTY 7 2. GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF THE EUT 8 2.2 DESCRIPTION OF THE TEST MODES 9 2.3 TEST SOFTWARE AND POWER LEVEL 10 2.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 10 2.5 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 11 2.6 EQUIPMENTS LIST 12 3. EMC EMISSION TEST 13 3.1 CONDUCTED EMISSION MEASUREMENT 13 3.2 TEST PROCEDURE 14 3.3 TEST SETUP 14 3.4 EUT OPERATING CONDITIONS 14 3.5 TEST RESULTS 15 4. RADIATED EMISSION MEASUREMENT 17 4.1 RADIATED EMISSION LIMITS 17 4.2 TEST PROCEDURE 19 4.3 TEST SETUP 20 4.4 EUT OPERATING CONDITIONS 20 4.5 FIELD STRENGTH CALCULATION 21 4.6 TEST RESULTS 21 5. CONDUCTED SPURIOUS & BAND EDGE EMISSION 32 5.1 LIMIT 32 5.2 TEST PROCEDURE 32 5.3 TEST SETUP 32 5.4 EUT OPERATION CONDITIONS 32 5.5 TEST RESULTS 32 6. POWER SPECTRAL DENSITY TEST 33 6.1 LIMIT 33 6.2 TEST PROCEDURE 33 6.3 TEST SETUP 33 Page 4 of 65 Report No.: STS2603407W01 Table of Contents Page 6.4 EUT OPERATION CONDITIONS 33 6.5 TEST RESULTS 33 7. BANDWIDTH TEST 34 7.1 LIMIT 34 7.2 TEST PROCEDURE 34 7.3 TEST SETUP 34 7.4 EUT OPERATION CONDITIONS 34 7.5 TEST RESULTS 34 8. PEAK OUTPUT POWER TEST 35 8.1 LIMIT 35 8.2 TEST PROCEDURE 35 8.3 TEST SETUP 35 8.4 EUT OPERATION CONDITIONS 35 8.5 TEST RESULTS 35 9. ANTENNA REQUIREMENT 36 9.1 STANDARD REQUIREMENT 36 9.2 EUT ANTENNA 36 APPENDIX 1-TEST DATA 37 APPENDIX 2- EUT TEST PHOTO 65 Page 5 of 65 Report No.: STS2603407W01 Revision History Rev. Issue Date Report No. Effect Page Contents 00 29 Apr. 2026 STS2603407W01 ALL Initial Issue Page 6 of 65 Report No.: STS2603407W01 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: KDB 558074 D01 15.247 Meas Guidance v05r02. FCC Part 15.247,Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS -- 15.247 (a)(2) 6dB Bandwidth PASS -- 15.247 (b)(3) Output Power PASS -- 15.209 Radiated Spurious Emission PASS -- 15.247 (d) Conducted Spurious & Band Edge Emission PASS -- 15.247 (e) Power Spectral Density PASS -- 15.205 Restricted bands of operation PASS -- Part 15.247(d)/ Part 15.209(a) Band Edge Emission PASS -- 15.203 Antenna Requirement PASS -- Note: (1) ‘N/A’ denotes test is not applicable in this Test Report. (2) All tests are according to ANSI C63.10-2020. Page 7 of 65 Report No.: STS2603407W01 1.1 TEST FACTORY SHENZHEN STS TEST SERVICES CO., LTD Add. : 101, Building B, Zhuoke Science Park, No.190 Chongqing Road, ZhanChengShequ, Fuhai Sub-District, Bao’an District, Shenzhen, Guang Dong, China FCC test Firm Registration Number: 625569 IC test Firm Registration Number: 12108A A2LA Certificate No.: 4338.01 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 RF output power, conducted ±0.751dB 2 Unwanted Emissions, conducted ±2.888dB 3 All emissions, radiated 9K-30MHz ±2.48dB 4 All emissions, radiated 30M-1GHz ±2.52dB 5 All emissions, radiated 1G-18GHz ±3.48dB 6 All emissions, radiated>18GHz ±4.18dB 7 Conducted Emission (9KHz-150KHz) ±2.48dB 8 Conducted Emission (150KHz-30MHz) ±2.52dB 9 Occupied Channel Bandwidth ±3.6% 10 Power Spectral Density, conducted ±1.214dB 11 Duty Cycle ±3.2% Page 8 of 65 Report No.: STS2603407W01 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF THE EUT Product Name Integrated follow-up camera with pan tilt and selfie stick Brand Name N/A Model Name V28 Series Model(s) V18 Model Difference All models are identical except for the model name, the test model is V28. Product Description The EUT is a Integra…

Text truncated - open the document above for the full version.

Page 1 of 2 FCC ID: 2BWB4-V28 Conducted emissions 30MHz-1GHz Page 2 of 2 FCC ID: Spurious emissions RF