2BWDM-JMN-YBPCAutomotive multi-function dashboard display

1. Sand Mode 2. Snow Mode 3. Road Mode 4. Mountain Mode 5. Swamp Mode Different UI brings you a unique driving experience Sport Classics Comfortable FCC Caution. (1)§ 15.19 Labelling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. § 15.21 Changes or modification warning Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. § 15.105 Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. RF warning for Mobile device: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Covered Equipment Attestation Letter For Certification Service in the USA Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Section 2.911(d)(5)(i)-(ii) of the Commission’s Rules (47 C.F.R.) we attest as follows for the product listed below: FCC ID Model name 2BWDM-JMN-YBP JMN-YBP We, Applicant Company Name: Guangzhou Yi Qin Technology Co., Ltd. Address: Room 203, Building 4, No. 6 Yongxing AutoParts Street, Baiyun District, Guangzhou City, Guangdong, China Phone: +86-13476077090 certify that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. This includes the cybersecurity and anti-virus software produced or provided by Kaspersky Lab, Inc. or any of ist successors and assignees. We certify that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. If you have any questions, please feel free to contact us at the address shown below. Sincerely, 2026-06-02 Signature Date Name / Title: Sade Loos / Manager Company: Guangzhou Yi Qin Technology Co., Ltd. Address: Room 203, Building 4, No. 6 Yongxing AutoParts Street, Baiyun District, Guangzhou City, Guangdong, China Phone: +86-13476077090 Fax: +86-13476077090 E-Mail: [email protected]

Due Diligence Letter For Certification Service in the USA Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern FCC ID Model name 2BWDM-JMN-YBP JMN-YBP Pursuant to KDB 986446 D01 Covered Equipment Guidance the evaluation of the product above shows compliance for the following reasons: Compliance Evaluation process Results Inherent compliance The chipset(s) used is not capable of running the cybersecurity and/or anti- virus software The memory used does not allow the running the cybersecurity and/or anti- virus software The storage capacity does not allow the running the cybersecurity and/or anti-virus software The operating system used is not capable of running the cybersecurity and/or anti-virus software No inherent compliance Based on software bill of material Compliance Based on scan for running software on the device Based on filesystem scan for cybersecurity and/or anti-virus software The equipment for which authorization is sought complies with the rules and fulfils the requirements as detailed in the above mentioned KDB. Evaluation performed by Company Name: MAXLAB Testing Co., Ltd. Contact Name: Harry Chen Address: 1/F, Building B, Xinshidai GR Park,Shiyan Street, Bao'an District, Shenzhen,Guangdong, 518052, People’s Republic of China Phone: +86-15691418608 Email: [email protected] Signature: Date: 2026-05-28

Confidentiality Request Letter For Certification Service in the USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we request confidentiality for the documentation of the following products: FCC ID Model name 2BWDM-JMN-YBP JMN-YBP For the products listed above, we request permanent confidentiality for all applicable exhibits as there are: • the Operational Description • the Block Diagram • the Schematics • the Part List • the Tune up Information The above listed exhibits contain trade secrets and proprietary information that could be of benefit to our competitors. If you have any questions, please feel free to contact us at the address shown below. Sincerely, 2026-06-02 Signature Date Name / Title: Sade Loos / Manager Company: Guangzhou Yi Qin Technology Co., Ltd. Address: Room 203, Building 4, No. 6 Yongxing AutoParts Street, Baiyun District, Guangzhou City, Guangdong, China Phone: +86-13476077090 Fax: +86-13476077090 E-Mail: [email protected]

Guangzhou Yi Qin Technology Co., Ltd. Room 203, Building 4, No. 6 Yongxing AutoParts Street, Baiyun District, Guangzhou City, Guangdong, China Date: June 2, 2026 FCC ID: 2BWDM-JMN-YBP Model Number: JMN-YBP To: Federal Communication Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21048 To Whom It May Concern, We, Guangzhou Yi Qin Technology Co., Ltd. hereby declare that our product (CAutomotive multi-function dashboard display) Model Number: JMN-YBP disable Bluetooth function (Bluetooth modular: AC6965E) via software due to marketing purposes, end user cannot use Bluetooth function in United States. We will apply new FCC ID if open Bluetooth function due to marketing requirements. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely, (Signed) Name / Title: Sade Loos / Manager Company: Guangzhou Yi Qin Technology Co., Ltd. Address: Room 203, Building 4, No. 6 Yongxing AutoParts Street, Baiyun District, Guangzhou City, Guangdong, China Phone: +86-13476077090 Fax: N/A E-Mail: [email protected]

Page 1 of 1 Rev.2.0 Guangzhou Yi Qin Technology Co., Ltd. WIFI Channel 12 and 13 Declaration Letter We declare the equipment identified below with regards to Channel 12 and 13 capabilities for FCC ID: 2BWDM-JMN-YBP Declaration Product hardware does not have the capability to operate on Channel 12 and 13. Product hardware has the capability to operate on Channel 12 and 13. However, these two channels will be disabled via software and will not be accessible to user. Product hardware has the capability to operate on Channel 12 and 13. However, all the operated channels can’t be changed in the RF parameter via software. All channels have complied with all of the requirements sets out in FCC Part 15.247. Product hardware has the capability to operate on WiFi Channel 12 and 13, and meets the requirements of KDB 594280 D01 v02r01. Please note: 1.) By default, this device operates in a mode that is compliant with the U.S. requirements. 2.) This device will also use supplemental information such as geo- location data to determine that it is operating outside the U.S., if necessary, to change its power. Such supplemental data will be derived from the following: Global Navigation Satellite System (GNSS)7 sensors in the device Mobile Country Code (MCC),8 or MCC with a Mobile Network code (MNC), received from a CMRS9 carrier and received directly by a receiver on the device Country information derived from multiple adjacent access points (for example using IEEE Std 802.11d provisions) may be permitted on case-by-case basis Other suitable geo-location data based on IP addresses or other reliable source. Name / Title: Sade Loos / Manager Signature: Phone: +86-13476077090 Email: [email protected] Date: 2026-06-02

Page1of7 MAXLABTestingCo.,Ltd. ReferencetotheappendixIIfordetails. EUTPHOTO(ExternalPhotos) FCC ID: 2BWDM-JMN-YBP Page2of7 MAXLABTestingCo.,Ltd. Page3of7 MAXLABTestingCo.,Ltd.

FCCIDLABELINGANDLOCATION FCCIDLabel FCCIDLabelLocation Thelabelshownshallbepermanentlyaffixedataconspicuouslocationonthedeviceandbe readilyvisibletotheuseratthetimepurchase(Labelingrequirementsper2.925) Automotivemulti-functiondashboarddisplay FCCID:2BWDM-JMN-YBP

Page4of8 MAXLABTestingCo.,Ltd. EUTPHOTO(InternalPhotos) FCC ID: 2BWDM-JMN-YBP Page5of8 MAXLABTestingCo.,Ltd. ExternalAntenna(GPS) n Page6of8 MAXLABTestingCo.,Ltd. Page7of8 MAXLABTestingCo.,Ltd. PFCAntenna(WIFI) n PFCAntenna(BT) n Page8of8 MAXLABTestingCo.,Ltd. ExternalAntenna(GPS) n

Page 1 of3 MAXLABTestingCo.,Ltd.ReportNo.:MAX26052712P01-R01RF RFTESTREPORT ReportReferenceNo........................:MAX26052712P01-R01RF FCCID................................................:2BWDM-JMN-YBP Compiledby (position+printedname+signature) .. : Engineer/CindyZheng Supervisedby (position+printedname+signature) .. : Manager/HaleyWen Approvedby (position+printedname+signature)..: RFManager/VivianJiang Dateofissue ......................................... :May28,2026 TestingLaboratoryName ................ : MAXLABTestingCo.,Ltd. Address.................................................: 1/F,BuildingB,XinshidaiGRPark,ShiyanStreet,Bao'anDistrict, Shenzhen,Guangdong,518052,People’sRepublicofChina Applicant’sname...............................:GuangzhouYiQinTechnologyCo.,Ltd. Address.................................................: Room203,Building4,No.6YongxingAutoPartsStreet,Baiyun District,GuangzhouCity Manufacturer’sname........................:GuangzhouYiQinTechnologyCo.,Ltd. ManufacturerAddress.........................: Room203,Building4,No.6YongxingAutoPartsStreet,Baiyun District,GuangzhouCity Testspecification..............................: Standard................................................:KDB447498D01GeneralRFExposureGuidancev06 MAXLABTestingCo.,Ltd.Allrightsreserved. Thispublicationmaybereproducedinwholeorinpartfornon-commercialpurposesaslongasthe MAXLABTestingCo.,Ltd.isacknowledgedascopyrightownerandsourceofthematerial.MAXLABTesting Co.,Ltd.takesnoresponsibilityforandwillnotassumeliabilityfordamagesresultingfromthereader's interpretationofthereproducedmaterialduetoitsplacementandcontext. Equipmentdescription.....................:Automotivemulti-functiondashboarddisplay TradeMark............................................:N/A Model/Typereference.........................:JMN-YBP ListedModels.....................................:N/A Modulation...........................................:CCK/DSSS/OFDM Frequency..............................................From2412-2462MHz Ratings...................................................:DC5V Result ..................................................... :PASS Page 2 of3 MAXLABTestingCo.,Ltd.ReportNo.:MAX26052712P01-R01RF RFExposureEvaluation Limits Thecriterialistedinthefollowingtableshallbeusedtoevaluatetheenvironmentimpactofhumanexposure toradiofrequency(RF)radiationasspecifiedin1.1307(b) AccordingtoKDB447498D01GeneralRFExposureGuidancev06,Unlessspecificallyrequiredbythe publishedRFexposureKDBprocedures,standalone1-gheadorbodyand10-gextremitySARevaluationfor generalpopulationexposureconditions,bymeasurementornumericalsimulation,isnotrequiredwhenthe correspondingSARTestExclusionThresholdcondition(s),listedbelow,is(are)satisfied. LimitsforMaximumPermissibleExposure(MPE) Frequencyrange (MHz) Electricfield strength (V/m) Magneticfieldstrength (A/m) Powerdensity (mW/cm 2 ) Averagingtime (minutes) (A)LimitsforOccupational/ControlledExposures 0.3–3.06141.63*(100)6 3.0–301842/f4.89/f*(900/f 2 )6 30–30061.40.1631.06 300–1500f/3006 1500–100,00056 (B)LimitsforGeneralPopulation/UncontrolledExposure 0.3–1.346141.63*(100)30 1.34–30824/f2.19/f*(180/f 2 )30 30–30027.50.0730.230 300–1500f/150030 1500–100,0001.030 f=frequencyinMHz Friistransmissionformula:Pd=(Pout*G)/(4*pi*r 2 ) Where Pd=powerdensityinmW/cm 2 ,Pout=outputpowertoantennainmW; G=gainofantennainlinearscale,Pi=3.1416; R=distancebetweenobservationpointandcenteroftheradiatorincm PdidthelimitofMPE,1mW/cm 2 .Ifweknowthemaximumgainoftheantennaandthetotalpowerinputto theantenna,throughthecalculation,wewillknowthedistancerwheretheMPElimitisreached. TestProcedure SoftwareprovidedbyclientenabledtheEUTtotransmitandreceivedataatlowest,middleandhighest channelindividually. Page 3 of3 MAXLABTestingCo.,Ltd.ReportNo.:MAX26052712P01-R01RF TestResultofRFExposureEvaluation WiFi2.4G Channel Frequen cy (MHz) Outputpower toantenna (dBm) Outputpowerto antenna(mW) PowerDensityat R=20cm (mW/cm 2 ) Limit (mW/cm 2 ) Result 802.11b 241210.3110.740.003331.0PASS 243710.3310.790.003351.0PASS 246210.4511.090.003441.0PASS 802.11g 24129.358.610.002671.0PASS 24379.038.000.002481.0PASS 24629.979.930.003081.0PASS 802.11n (HT20) 24128.937.820.002431.0PASS 24378.146.520.002021.0PASS 24628.657.330.002271.0PASS 802.11n (HT40) 24227.565.700.001771.0PASS 24377.245.300.001641.0PASS 24527.816.040.001871.0PASS Remark:Antennagain:1.93dBi EUT'smoduleismorethan20cmawayfromthehumanbody. Conclusion:ThemeasurementresultscomplywiththeFCCLimitper47CFR2.1091forthe uncontrolledRFExposureofmobiledevice.

Specification description： 2.4G new soft built- in 1.13 wire L=120MM(1st generation terminal) Model: JMN-YBP 第 1 页 共 7 页 Manufacturer’s name: Guangzhou Yi Qin Technology Co., Ltd. Manufacturer Address: Room 203, Building 4, No. 6 Yongxing Auto Parts Street, Baiyun District, Guangzhou City Antenna Specifications 1、product picture 2 . VSWR 第 2 页 共 7 页 3· Product performance parameter： 电性能指标 Electrical Specifications 频率范围 FrequencyRange (MHz) 2400-2500 输入阻抗 InputImpendence (Ω) 50 电压驻波比V.S.W.R ≤3.0 （未匹配设备，仅供参考） 增益Gain(dBi) 1.93（Max） 极化形式 PolarizationType 垂直Vertical 最大功率Maximumpower(W) 10W 垂直面波瓣角度Vertical lobe Angle（E） 45~60° 水平面波瓣角度 Water plane lobeAngle （ H ） 360° 机械指标 Mechanical Specifications 天线材质 Material FPC 连接器型号 ConnectType IPEX(1 代 ) 天线尺寸 Size 45*10MM 工作温度OperatingTemp -20~+65 ̊C 储存温度Storage Temp -30~ +75 ̊C 第 3 页 共 7 页 第 4 页 共 7页 3 、 Electrical test report 3.1 Guangzhou Yi Qin Technology Co., Ltd. 第 5 页 共 7 页 3.2Efficiency&gain Frequency (MHz)Efficiency (%)Peak Gain (dBi) 240064.431.93 245063.491.88 250063.621.80 Guangzhou Yi Qin Technology Co., Ltd. 第 6 页 共 7 页 3.33D&2D Pattern 第 7 页 共 7 页 Guangzhou Yi Qin Technology Co., Ltd.

Page 1 of 31 MAXLAB Testing Co.,Ltd. Report No.: MAX26052712P01-R01 FCC PART 15 SUBPART C TEST REPORT FCC PART 15.247 Report Reference No. ....................... :MAX26052712P01-R01 FCC ID. ................................................ :2BWDM-JMN-YBP Compiled by ( position+printed name+signature) .. : Engineer/ Cindy Zheng Supervised by ( position+printed name+signature)..: Manager/Haley Wen Approved by ( position+printed name+signature) .. : RF Manager/ Vivian Jiang Date of issue.........................................:May 28, 2026 Testing Laboratory Name................:MAXLAB Testing Co.,Ltd. Address ................................................. : 1/F, Building B, Xinshidai GR Park,Shiyan Street, Bao'an District, Shenzhen,Guangdong, 518052, People’s Republic of China Applicant’s name...............................:Guangzhou Yi Qin Technology Co., Ltd. Address.................................................: Room 203, Building 4, No. 6 Yongxing Auto Parts Street, Baiyun District, Guangzhou City Manufacturer’s name ........................ : Guangzhou Yi Qin Technology Co., Ltd. Manufacturer Address.........................: Room 203, Building 4, No. 6 Yongxing Auto Parts Street, Baiyun District, Guangzhou City Test specification..............................: Standard ................................................ : FCC Part 15.247 KDB558074 D01 15.247 Meas Guidance v05r02 ANSI C63.10-2020 + Cor. 1-2023 + C63.10a- 2024 + Errata to C63.10a-2024 MAXLAB Testing Co.,Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the MAXLAB Testing Co.,Ltd.is acknowledged as copyright owner and source of the material. MAXLAB Testing Co.,Ltd.takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description ........................ :Automotive multi-function dashboard display Trade Mark ............................................ : N/A Model/Type reference.........................: JMN-YBP Listed Models......................................: N/A Modulation Type..................................:CCK/ DSSS/ OFDM Operation Frequency .......................... :From 2412 - 2462MHz Ratings ................................................... :DC 5V Result ..................................................... :PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. MAXLAB Testing Co.,Ltd. Report No.: MAX26052712P01-R01 Page 2 of 31 Contents 1 T E S T S T A N D A R D S...........................................................................................................................................3 2 S U M M A R Y................................................................................................................................................................4 2.1 General Remarks ......................................................................................................................................................... 4 2.2 Product Description ................................................................................................................................................... 4 2.3 Equipment Under Test...............................................................................................................................................4 2.4 Short description of the Equipment under Test (EUT).....................................................................................4 2.5 EUT operation mode...................................................................................................................................................5 2.6 Block Diagram of Test Setup...................................................................................................................................5 2.7 Related Submittal(s) / Grant (s) ............................................................................................................................... 5 2.8 Modifications ................................................................................................................................................................ 5 3 T E S T E N V I R O N M E N T.....................................................................................................................................6 3.1 Address of the test laboratory.................................................................................................................................6 3.2 Test Facility...................................................................................................................................................................6 3.3 Environmental conditions.........................................................................................................................................6 3.4 Test Description .......................................................................................................................................................... 7 3.5 Statement of the measurement uncertainty ........................................................................................................ 7 3.6 Equipments Used during the Test..........................................................................................................................8 4 T E S T C O N D I T I O N S A N D R E S U L T S................................................................................................1 0 4.1 AC Power Conducted Emission............................................................................................................................10 4.2 Radiated Emission...............................................................................................................................…

Text truncated - open the document above for the full version.

Page 1 of 1 MAXLAB Testing Co.,Ltd. Reference to the appendix I for details. EUT TEST PHOTO FCC ID: 2BWDM-JMN-YBP