2BWFF-PS0230WIFIBiometric Dropdown Safe Elite Wi-Fi

Biometric Dropdown Safe Elite Instruction Manual (PS0230) VERPROOFSafe secures your peace of mind VERPROOF ® THE BEST SAFE FOR ULTIMATE SAFETY AND PROTECTION Thank you so much for your purchase. We hope you’re happy with the item and our service. Should there be any problems with the item, please do not hesitate to contact us. [email protected] After-sales Service @VerproofSafe BOX CONTENTS I. Mounting Bracket II. Panel (Button & Biometric Scanner) III. Override Keyhole IV. Mounting Holes V. Thumb Mounting Holes VI. Rubber Bumper VII. Override Keys (×2) VIII. Wood Screws (×4) IX. Thumb Screws (×3) X. M4 Nuts (×2) 01/Verproof Biometric Safe Elite I II III IV V VI VII VIII IX X WARNINGS As a firearms owner, you are responsible for ensuring that children and other unauthorized individuals cannot access your guns at home. Please follow the following safety measures before using this unit. DO NOT LOSE THE OVERRIDE KEYS OR STORE THEM IN THE SAFE. DO NOT expose the safe to extreme low/high temperatures as it may affect battery life. DO NOT store loaded guns in this unit. Firearms can be dangerous and must be handled with respect. REGULARLY confirm whether the door is fully locked and check the battery level. NEITHER SELLER NOR MANUFACTURER SHALL BE LIABLE FOR UNAUTHORIZED ACCESS, ANY INJURY, LOSS OR DAMAGE TO PERSONAL PROPERTY DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OF, OR THE INABILITY TO USE THE VERPROOF ® SAFES. THE USER SHALL DETERMINE THE SUITABILITY OF THE VERPROOF ® SAFES BEFORE THE INTENDED USE AND USER ASSUMES ALL RISK AND LIABILITY WHATSOEVER IN CONNECTION THEREWITH, VERPROOF ® SAFES ARE NOT INTENDED TO PROTECT AGAINST ENVIRONMENTAL HAZARDS INCLUDING FIRE AND WATER. Be sure to follow all local and state firearm laws. DO NOT operate a firearm without proper training and experience. DISCLAIMERS 02/Verproof Biometric Safe Elite BATTERY INSTALLATION 1 Place the safe upright. Insert an override key into the keyhole and turn clockwise to open the door (Figure A). 2 Locate the battery compartment cover behind the keypad inside the safe (Figure B). 3 Open the cover, remove the battery box, and insert four AA alkaline batteries. Ensure correct polar- ity (two positive electrodes face upward; see Figure C). 4 Reinsert the box and close the cover. 5 Repeat the steps above for battery replacement. Battery Guidelines 1 Use high-quality alkaline batteries; do not mix old and new or different battery types. 2 Avoid extreme temperatures. 3 When power is low, the keypad indicator turns yellow—replace the batteries promptly. 4 Remove exhausted batteries and dispose of them properly. ATTENTION: VERPROOF ® Safe auto-locks when the door is fully closed. Do not leave the override key inside the safe. All voice prompts can be turned off by enabling silent mode. 03/Verproof Biometric Safe Elite A B C MASTER CODE PROGRAMMING 04/Verproof Biometric Safe Elite After receiving the safe, you need to set your own password as soon as possible to prevent unauthorized access to your safe. TIPS: Code Requirements • 3-12 digits. • Press buttons one at a time (no simultaneous presses). • Recording must be completed within 20 seconds. • Programming a new code overwrites the previous code. • There will be voice guidance in programming, which can be turned off by enabling the silent mode (Page 7). 1 Enter the default code 1-2-3-4 to open the safe. 2 Press and hold the Learn button (1 second), and the indicator will turn green with one beep (Figure D). 3 Enter your NEW master code, then press the Learn button again for 1 second to confirm, the indica- tor will flash green three times with beeps, indicating a successful setup. 4 If the indicator flashes red three times with beeps, the setup has failed. Start again from Step 2. Note: • The “Learn” button is on the left side of the LED light, please be careful not to confuse it with the “Mute” button. • Holding it down for 3 seconds will reset all of the fingerprints to default. Please keep your master code in a safe place. D FINGERPRINT REGISTRATION 05/Verproof Biometric Safe Elite ATTENTION: • Up to 100 fingerprints can be stored. • Keep your finger clean when registering fingerprints. • Keep the core of the fingerprint flat (Figure E+F) over the center of the scanner. • Adjust your finger slightly between scans for increased accuracy. • If your fingerprints are difficult to identify, register the same finger 4-5 times for increased accuracy. • There will be voice guidance in programming, which can be turned off by enabling the silent mode (Page 7). 1 Enter the previously set master code to open the safe. 2 Locate and press the Learn button (1 second), the indicator will turn green with one beep (Figure G). 3 Place your finger on the biometric scanner and tap it 4 times. Each tap will end with a green flash and one beep. The last tap will end with a green flashing three times and beeps, indicating a success- ful setup. 4 If the indicator flashes red three times with beeps, the setup failed. Start again from Step 2. Note: • The “Learn” button is on the left side of the LED light, please be careful not to confuse it with the “Mute” button. • Holding it down for 3 seconds will reset all of the fingerprints to default. E F G DELETING THE REGISTERED FINGERPRINTS 06/Verproof Biometric Safe Elite OPEN SAFE BY FINGERPRINT Place a previously registered finger onto the scanner to open the safe. Note: • Keep your finger clean when identifying fingerprints. • When a correct fingerprint is read, the green light will turn on with one beep and the door should open. • If an incorrect fingerprint is read, the red light will flash with beeps. • After 5 incorrect entries, the red light will flash with beeps and “Too many input errors, safe locked”, the safe will be disabled for 1 minute. OPEN SAFE BY MASTER CODE Enter the previously programmed 3-12 digital code to open the safe. 1 Press and hold the Learn button for 3 seconds; the indicator will flash green three times with beeps and…

Text truncated - open the document above for the full version.

Rev 1/26/2023 Ningbo Verproof Intelligent Technology Co, Ltd. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 06-08-2026 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2BWFF-PS0230WIFI [Ningbo Verproof Intelligent Technology Co, Ltd.] certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. [Ningbo Verproof Intelligent Technology Co, Ltd.] certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Sincerely, (Applicant signature) (Applicant printed name) Yujun Zhu Rev 1/26/2023 Ningbo Verproof Intelligent Technology Co, Ltd. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 06-08-2026 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2BWFF-PS0230WIFI [Ningbo Verproof Intelligent Technology Co, Ltd.] ce8rtifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) Yujun Zhu

Ningbo Verproof Intelligent Technology Co, Ltd. U.S. Agent Letter of Attestation To: Federal Communications Commission 7435 Oakland Mills Road, Columbia, MD 21046, USA Date: June 08, 2026 Ref: Attestation Statement – Part 2.911(d)(7) filing FCC ID: 2BWFF-PS0230WIFI Ningbo Verproof Intelligent Technology Co, Ltd. (“the applicant”) certifies that, as of the date of the filing of the application, CLF Import and Export Limited (“the agent”) is our designated U.S. agent for service of process for the above reference FCC ID. The applicant accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges it is our responsibility to inform the FCC whenever the agent information changes. CLF Import and Export Limited ("the agent) understand it is the agent's obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address. Designated U.S. Agent Company Name: CLF Import and Export Limited FRN: 0033489683 Address: 1312 17th Street #692, Denver, CO 80202, United States Signature: Contact Person: David Chen Tel: +1 949 254 2565 Email: [email protected] Applicant Company Name: Ningbo Verproof Intelligent Technology Co, Ltd. FRN: 0038495537 Address: Room 321, Building 4, Zone F, China Plastics City Central Trading Area, Yuyao, Zhejiang, 315400, China Signature: Contact Person: Yujun Zhu Tel: +86-18067202630 Email: [email protected]

Ningbo Verproof Intelligent Technology Co, Ltd. Date: June 08, 2026 Product Model Number: PS0230WIFI, ps0230wifi white FCC ID: 2BWFF-PS0230WIFI To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following: • Testing • Approval applications and procedures We declare that QAI Laboratories Ltd. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by QAI Laboratories Ltd. on our behalf shall have the same effect as acts of our own. By: Yujun Zhu Contact Listed on FCC Wesbite Title: Manager Email: [email protected] Telephone: +86-18067202630 On behalf of: Ningbo Verproof Intelligent Technology Co, Ltd.

Ningbo Verproof Intelligent Technology Co, Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: June 8, 2026 Subject; Request for Confidentiality FCC ID: 2BWFF-PS0230WIFI To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Software Security Requirements for UNII devices It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Yujun Zhu Title: Manager

Ningbo Verproof Intelligent Technology Co, Ltd. Model Difference Statement DATE: June 08, 2026 FCC ID: 2BWFF-PS0230WIFI Dear Sir/Madam, Added models ps0230wifi white asis of the original product PS0230WIFI The color of appearance and model name of series models listed are different from the main model, but the circuit and the electronic construction are the same, declared by the manufacturer. Sincerely, Name: Yujun Zhu Title: Manager Company name: Ningbo Verproof Intelligent Technology Co, Ltd. Address: Room 321, Building 4, Zone F, China Plastics City Central Trading Area, Yuyao, Zhejiang, 315400, China

Report No: SSP26050310-1E FCC ID: 2BWFF-PS0230WIFI Annex of Test Report Annex A. EUT External Photos Model: PS0230WIFI EUT View 1 EUT View 2 Report No: SSP26050310-1E FCC ID: 2BWFF-PS0230WIFI Annex of Test Report EUT View 3 EUT View 4 Report No: SSP26050310-1E FCC ID: 2BWFF-PS0230WIFI Annex of Test Report EUT View 5 EUT View 6 Report No: SSP26050310-1E FCC ID: 2BWFF-PS0230WIFI Annex of Test Report EUT View 7 EUT View 8 Report No: SSP26050310-1E FCC ID: 2BWFF-PS0230WIFI Annex of Test Report EUT View 9

Report No: SSP26050310-1E FCC ID: 2BWFF-PS0230WIFI Annex of Test Report Annex D. Label and Information FCC Label Sample Label Size:2.5cm*1cm FCC Label Specifications Text is Black in color and is justified. Labels are printed in indelible ink on permanent adhesive backing or silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Where the EUT is constructed in two or more sections connected by wires and marketed together, the above statement is required to be affixed only to the main control unit. When the EUT is so small or for such use that it is not practicable to place the statement on it, the above information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. FCC Label Location

Report No: SSP26050310-1E FCC ID: 2BWFF-PS0230WIFI Annex of Test Report Annex B. EUT Internal Photos Model: PS0230WIFI EUT Internal View 1 EUT Internal View 2 FPCB Antenna Report No: SSP26050310-1E FCC ID: 2BWFF-PS0230WIFI Annex of Test Report EUT Internal View 3 EUT Internal View 4 Report No: SSP26050310-1E FCC ID: 2BWFF-PS0230WIFI Annex of Test Report EUT Internal View 5 EUT Internal View 6 Report No: SSP26050310-1E FCC ID: 2BWFF-PS0230WIFI Annex of Test Report EUT Internal View 7 EUT Internal View 8

FCC ID: 2BWFF-PS0230WIFI RF Exposure Evaluation According to KDB 447498 D01 General RF Exposure Guidance v06 and part 2.1093，Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition(s), listed below, is (are) satisfied. For 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extremity SAR, where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison Here, The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. For BLE Max Conducted Power(dBm) Tune-up Power(dBm) Max Tune-up Power(dBm) Max Power(mW) Frequency(MHz) Min. distance(mm) Calc. thresholds limit 1.65 1(±1) 2 1.585 2402 5 0.4912 3.0 For 2.4GWiFi Max Conducted Power(dBm) Tune-up Power(dBm) Max Tune-up Power(dBm) Max Power(mW) Frequency(MHz) Min. distance(mm) Calc. thresholds limit 5.48 5(±1) 6 3.981 2412 5 1.236 3.0 Remark: antenna gain= BLE: 0.7dBi, 2.4GWiFi: 0.7dBi The device is capable of simultaneously transmitting 2.4G WiFi and Bluetooth. Calculations for simultaneously transmit Mode Ratios Result Limit Result BR+EDR 0.1637 0.5757 1 PASS 2.4G Wi-Fi 0.412 Ratios = Power Density / Power density Limit So a SAR test is not required

Report No: SSP26050310-1E FCC Test Report Page 1 of 33 FCC TEST REPORT FCC ID: 2BWFF-PS0230WIFI Report No. : SSP26050310-1E Applicant : Ningbo Verproof Intelligent Technology Co, Ltd. Product Name : Biometric Dropdown Safe Elite Wi-Fi Model Name : PS0230WIFI Test Standard : FCC Part 15.247 Date of Issue : 2026-06-03 Shenzhen CCUT Quality Technology Co., Ltd. 1F, Building 35, Changxing Technology Industrial Park, Yutang Street, Guangming District, Shenzhen, Guangdong, China; (Tel.:+86-755-23406590 website: www.ccuttest.com) This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd. Report No: SSP26050310-1E FCC Test Report Page 2 of 33 Test Report Basic Information Applicant..................................: Ningbo Verproof Intelligent Technology Co, Ltd. Address of Applicant...............: Room 321, Building 4, Zone F, China Plastics City Central Trading Area, Yuyao, Zhejiang, 315400, China Manufacturer..........................: Ningbo Verproof Intelligent Technology Co, Ltd. Address of Manufacturer........: Room 321, Building 4, Zone F, China Plastics City Central Trading Area, Yuyao, Zhejiang, 315400, China Product Name.........................: Biometric Dropdown Safe Elite Wi-Fi Brand Name.............................: Verproof Main Model..............................: PS0230WIFI Series Models..........................: See section 1.1 (Page 5) Test Standard..........................: FCC Part 15 Subpart C KDB 558074 D01 15.247 Meas Guidance v05r02 ANSI C63.4-2014 ANSI C63.10-2020 + Cor.1-2023 Date of Test .............................: 2026-05-19 to 2026-06-02 Test Result...............................: PASS Tested By ................................: (Coke Huang) Reviewed By............................: (Lorzix Luo) Authorized Signatory............: (Lahm Peng) Note : This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd.. All test data presented in this test report is only applicable to presented test sample. Report No: SSP26050310-1E FCC Test Report Page 3 of 33 CONTENTS 1. General Information ....................................................................................................................................................5 1.1 Product Information .............................................................................................................................................5 1.2 Test Setup Information..........................................................................................................................................6 1.3 Compliance Standards ...........................................................................................................................................7 1.4 Test Facilities ........................................................................................................................................................7 1.5 List of Measurement Instruments ..........................................................................................................................8 1.6 Measurement Uncertainty .....................................................................................................................................9 2. Summary of Test Results ........................................................................................................................................... 10 3. Antenna Requirement ............................................................................................................................................... 11 3.1 Standard and Limit.............................................................................................................................................. 11 3.2 Test Result .......................................................................................................................................................... 11 4. Conducted Emissions ................................................................................................................................................ 12 4.1 Standard and Limit.............................................................................................................................................. 12 4.2 Test Procedure.................................................................................................................................................... 12 4.3 Test Data and Results .......................................................................................................................................... 13 5. Radiated Emissions ................................................................................................................................................... 16 5.1 Standard and Limit.............................................................................................................................................. 16 5.2 Test Procedure.................................................................................................................................................... 16 5.3 Test Data and Results .......................................................................................................................................... 18 6. Band-edge Emissions(Radiated) ............................................................................................................................... 22 6.1 Standard and Limit.............................................................................................................................................. 22 6.2 Test Procedure.................................................................................................................................................... 22 6.3 Test Data and Results ....…

Text truncated - open the document above for the full version.

Report No: SSP26050310-2E FCC Test Report Page 1 of 50 FCC TEST REPORT FCC ID: 2BWFF-PS0230WIFI Report No. : SSP26050310-2E Applicant : Ningbo Verproof Intelligent Technology Co, Ltd. Product Name : Biometric Dropdown Safe Elite Wi-Fi Model Name : PS0230WIFI Test Standard : FCC Part 15.247 Date of Issue : 2026-06-03 Shenzhen CCUT Quality Technology Co., Ltd. 1F, Building 35, Changxing Technology Industrial Park, Yutang Street, Guangming District, Shenzhen, Guangdong, China; (Tel.:+86-755-23406590 website: www.ccuttest.com) This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd. Report No: SSP26050310-2E FCC Test Report Page 2 of 50 Test Report Basic Information Applicant..................................: Ningbo Verproof Intelligent Technology Co, Ltd. Address of Applicant...............: Room 321, Building 4, Zone F, China Plastics City Central Trading Area, Yuyao, Zhejiang, 315400, China Manufacturer..........................: Ningbo Verproof Intelligent Technology Co, Ltd. Address of Manufacturer........: Room 321, Building 4, Zone F, China Plastics City Central Trading Area, Yuyao, Zhejiang, 315400, China Product Name.........................: Biometric Dropdown Safe Elite Wi-Fi Brand Name.............................: Verproof Main Model..............................: PS0230WIFI Series Models..........................: See section 1.1 (Page 5) Test Standard..........................: FCC Part 15 Subpart C KDB 558074 D01 15.247 Meas Guidance v05r02 ANSI C63.4-2014 ANSI C63.10-2020 + Cor.1-2023 Date of Test .............................: 2026-05-19 to 2026-06-02 Test Result...............................: PASS Tested By ................................: (Coke Huang) Reviewed By............................: (Lorzix Luo) Authorized Signatory............: (Lahm Peng) Note : This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd.. All test data presented in this test report is only applicable to presented test sample. Report No: SSP26050310-2E FCC Test Report Page 3 of 50 CONTENTS 1. General Information ....................................................................................................................................................5 1.1 Product Information .............................................................................................................................................5 1.2 Test Setup Information..........................................................................................................................................6 1.3 Compliance Standards ...........................................................................................................................................7 1.4 Test Facilities ........................................................................................................................................................7 1.5 List of Measurement Instruments ..........................................................................................................................8 1.6 Measurement Uncertainty .....................................................................................................................................9 2. Summary of Test Results ........................................................................................................................................... 10 3. Antenna Requirement ............................................................................................................................................... 11 3.1 Standard and Limit.............................................................................................................................................. 11 3.2 Test Result .......................................................................................................................................................... 11 4. Conducted Emissions ................................................................................................................................................ 12 4.1 Standard and Limit.............................................................................................................................................. 12 4.2 Test Procedure.................................................................................................................................................... 12 4.3 Test Data and Results .......................................................................................................................................... 13 5. Radiated Emissions ................................................................................................................................................... 16 5.1 Standard and Limit.............................................................................................................................................. 16 5.2 Test Procedure.................................................................................................................................................... 16 5.3 Test Data and Results .......................................................................................................................................... 18 6. Band-edge Emissions(Radiated) ............................................................................................................................... 22 6.1 Standard and Limit.............................................................................................................................................. 22 6.2 Test Procedure.................................................................................................................................................... 22 6.3 Test Data and Results ....…

Text truncated - open the document above for the full version.

Page 1 of 3 1. General Information 1.1 Product Information Manufacturer: Ningbo Verproof Intelligent Technology Co, Ltd. Address of Manufacturer: Room 321, Building 4, Zone F, China Plastics City Central Trading Area, Yuyao, Zhejiang, 315400, China Product Name: 2.4G Antenna Model Name: PS0230WIFI Frequency Range: 2400MHz - 2500MHz Type of Antenna: FPCB Antenna Antenna Gain: 0.7dBi (Max.) Impedance: 50 ohm Antenna View: Page 2 of 3 2. OTA Test 2.1 Gain Frequency Peak Gain (dBi) Polarity 2400MHz 0.7 Horizontal 2400MHz -0.31 Vertical 2450MHz -1.22 Horizontal 2450MHz -1.56 Vertical 2500MHz -1.81 Horizontal 2500MHz -2.02 Vertical Page 3 of 3 2.2 Radiation Pattern View

Report No: SSP26050310-1E FCC ID: 2BWFF-PS0230WIFI Annex of Test Report Annex C. Test Photos Conducted Emission Test View 1 Radiated Emission Test View Below 1GHz Report No: SSP26050310-1E FCC ID: 2BWFF-PS0230WIFI Annex of Test Report Radiated Emission Test View Above 1GHz