2BWNX-LOCATOBluetooth Tracker

LOCATO 101 Works with Appleʼs Find My & Googleʼs Find Hub FCC Regulatory Information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, equipment and receiver. -- Connect the equipment into an outlet on a circuit different which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. 3 The FCC identification label is permanently printed on the back side of the LOCATO 101 device. The label contains the Model Number and FCC ID (2BWNX-LOCATO). The electronic label is located on the back side of the LOCATO 101 device. The circular label has a diameter of 20 mm. The overall product diameter is 33 mm. Electronic Label Exhibit Electronic Label Description Label Location Statement Product: LOCATO 101 Manufacturer: Atlanta Systems Pvt. Ltd. FCC ID: 2BWNX-LOCATO 4 Item Product Model FCC ID Label Type Label Location Back Label Diameter Overall Device Diameter Description LOCATO 101 2BWNX-LOCATO Permanent printed product label Back side of the device 20 mm 33 mm Front View (Ø33 mm) Back View (Ø20 mm) Width: 20mm, Height: 5mm(Approx) Illustrative Layout (Not to Scale) 5 IN THE BOX 1 x LOCATO 101 Device (IP67 waterproof & dustproof) 1 x User Manual Overview 6 FRONTREAR SIDE Power Button Lanyard Space Battery Cover Operation Apple Find My App Before using your LOCATO 101, attach it to your keys, wallet, backpack, luggage, handbag, or any valuable item you want to keep track of. Then, connect it to the Apple Find My app by following the steps below: •Turn on Bluetooth function. •Wi-Fi and mobile network connection must be in good condition. •Turn on 'Location Services' : Open 'Settings' > 'Privacy & Security' > 'Location Services' > 'Find My' (To see the most accurate location for your LOCATO 101, device turn on 'Precise Location' for Find My app.) Note: 1. It is better to update your Apple devices to the latest version of iOS. 2. Allow notifications from the App. Google Find Hub App 1. Download and install Find Hub App from Google Play Store. Note: If your phone already includes the app (Find Hub), proceed to the next step. 2. Turn on Bluetooth function of your phone. 3. Connect your phone to the Internet and keep the network signal strong. 4. Allow 'Find Hub' to access the location of your phone. Note: One LOCATO 101 device can only be connected to one smart phone. 7 Power On 1. Press the Power Button once. 2. The red LED flashes once, indicating that the device has powered on. 3. The device automatically initializes and sends its data. 4. After completing the transmission, LOCATO 101 automatically enters sleep mode to conserve battery power. Note: Sleep mode is the normal operating state of the device. It automatically wakes up whenever required during normal operation. Power Off LOCATO 101 does not require manual power-off during normal operation. After initialization and data transmission, the device automatically enters a low-power sleep mode to maximize battery life. 8 Operation Power On Data Transmission Sleep Mode LED Status Red LED flashes once No user action required LED Off Description Device powers on and starts initialization Device automatically sends data Device enters low-power sleep mode to conserve battery LOCATO 101 Device Setup Apple Quick Setup Scan the QR code with the Camera App on your device to directly search for the LOCATO 101 device. 1. Press the Power Button once. The red LED will flash once, indicating that the device has powered on. The tracker will automatically enter pairing mode. 2. On your iPhone, open the Apple Find My app, select the ‘Items’ tab, then tap ‘Add Item’ > ‘Other Supported Item’. 3. When ‘LOCATO 101’ appears in the list of available devices, tap Connect. 4. Assign a recognizable name to your ‘LOCATO 101’ and choose an emoji to help identify it in the Find My app. 5. Review the information and tap Agree to link the tracker to your Apple ID. 6. Once setup is complete, your ‘LOCATO 101’ will appear on the map in the Find My app. Tap Finish to complete the setup. 7. Your ‘LOCATO 101’ is now ready to use. Attach it to your keys, wallet, backpack, handbag, luggage, or any other valuable personal belongings using the built-in keyring hole. Note: If the device is not paired with an Apple device within 10 minutes after being powered on, it will automatically power off to conserve battery power. 9 the QR code support iOS, iPadQS Reference: The following screenshots are for illustration purposes only. The actual interface may vary depending on your iPhon…

Text truncated - open the document above for the full version.

1/1 USAgentforServiceofProcessLETTEROFATTESTATION TO: OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 USAgentforServiceofProcess: CompanyName:HOPEKCORPORATIONINC Address:16755CoyoteBushDrUnit84,SanDiego,CA92127UnitedStates FRN:0034562900 ContactName:YangyangXu TelephoneNo:(561)875-9826 E-mail:[email protected] ThisletteristoconfirmthattheUSAgentforServiceofProcessacceptsresponsibilitytoactas alocalrepresentativeonbehalfofATLANTASYSTEMSPVT.LTD. TheUSAgentforServiceofProcessisawareofandagreestocomplywiththerequirements outlinedintheFCCEquipmentAuthorizationProgram,ReportandOrderFCC22-84,andclause §2.911. Applicant: CompanyName:ATLANTASYSTEMSPVT.LTD. ProductDescription:BluetoothTracker FRN:0038550182 GranteeCode:2BWNX FCCID:2BWNX-LOCATO ContactName:SANDEEPNARULA Address:M-135,2ndFLOOR,CONNAUGHTPLACENEWDELHI-110001 TelephoneNo:+911149039710 E-mail:[email protected] TheApplicantisawareofandagreestocomplywiththerequirementsoutlinedintheFCC EquipmentAuthorizationProgram,ReportandOrderFCC22-84,andclause§2.911. ThisAgreementisvaliduntil(Permanentlyvalid). Date:2026/8/5 Applicant’sName: ATLANTASYSTEMSPVT.LTD. USAgentforServiceofProcess’sName: HOPEKCORPORATIONINC Title:DirectorTitle:Manager SignatureSignature

Rev 1/26/2023 ATLANTA SYSTEMS PVT. LTD. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: June 22, 2026 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2BWNX-LOCATO [ATLANTA SYSTEMS PVT. LTD.] certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. [ATLANTA SYSTEMS PVT. LTD.] certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Sincerely, (Applicant signature) (Applicant printed name) SANDEEP NARULA Rev 1/26/2023 ATLANTA SYSTEMS PVT. LTD. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: June 22, 2026 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2BWNX-LOCATO [ATLANTA SYSTEMS PVT. LTD.] certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) SANDEEP NARULA

ATLANTA SYSTEMS PVT. LTD. Family models declaration letter Aug. 06, 2026 We ATLANTA SYSTEMS PVT. LTD. Of M-135, 2nd FLOOR, CONNAUGHT PLACE NEW DELHI-110001 Declare under our sole responsibility that the product FCC ID: 2BWNX-LOCATO Product: Bluetooth Tracker Model Number: LOCATO 101 The model has multiple colors, these product are same PCB Layout, Schematics, BOM. Only for different appearance color for different market require. SANDEEP NARULA/ Director E-mail : [email protected] Phone : +911149039710 Fax : N/A Address : M-135, 2nd FLOOR, CONNAUGHT PLACE NEW DELHI-110001 No. Model Appearance color Appearance material Appearance identification 1 LOCATO 101 Black Plastic 2 LOCATO 101 White Plastic

ATLANTA SYSTEMS PVT. LTD. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: August 6, 2026 Subject; Request for Confidentiality FCC ID: 2BWNX-LOCATO To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Software Security Requirements for UNII devices In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: SANDEEP NARULA Title: Director

Effective Date: April 2, 2020 QSF 7.6.4-8 – Agent Authorization Letter Template Page 1 of 1 Revision Date: Revision: 0 ATLANTA SYSTEMS PVT. LTD. Date: June 22, 2026 Product Model Number: LOCATO 101 FCC ID: 2BWNX-LOCATO To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following:  Testing  Approval applications and procedures We declare that QAI Laboratories Ltd. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by QAI Laboratories Ltd. on our behalf shall have the same effect as acts of our own. By: Contact Listed on FCC Wesbite Title: Director Email: [email protected] Telephone: +911149039710 On behalf of: ATLANTA SYSTEMS PVT. LTD.

Ext Photos Model: LOCATO 101 Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6 Photo 7 Photo 8

Int Photos Model: LOCATO 101 Photo 1 Photo 2 Photo 3 Photo 4 ANT Photo 5 Photo 6

- Page 1 of 9 - Report No.: HB20260616001E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com RF EXPOSURE Test Report Product: Bluetooth Tracker Trade Mark: ATLANTA Model Number: LOCATO 101 FCC ID: 2BWNX-LOCATO Prepared for ATLANTA SYSTEMS PVT. LTD. M-135, 2nd FLOOR, CONNAUGHT PLACE NEW DELHI-110001 Prepared by Shenzhen HongBiao Certification& Testing Co., Ltd Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen, China Tel.: +86-755-2998 9321 Fax.: +86-755-2998 5110 Website: http://www.sz-hongbiao.com - Page 2 of 9 - Report No.: HB20260616001E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Table of Contents 1 GENERAL DESCRIPTION ..................................................................................................................................... 5 1.1 DESCRIPTION OF EUT ................................................................................................................................................ 5 1.2 TEST MODE .............................................................................................................................................................. 5 1.3 TEST SETUP .............................................................................................................................................................. 5 1.4 ANCILLARY EQUIPMENT .............................................................................................................................................. 5 2 TEST FACILITIES AND ACCREDITATIONS .............................................................................................................. 6 2.1 TEST LABORATORY ..................................................................................................................................................... 6 2.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 6 2.3 MEASUREMENT UNCERTAINTY ..................................................................................................................................... 6 2.4 TEST SOFTWARE ........................................................................................................................................................ 6 3 LIST OF TEST EQUIPMENT .................................................................................................................................. 7 4 RF EXPOSURE..................................................................................................................................................... 8 4.1 STANDALONE SAR TEST EXCLUSION CONSIDERATIONS........................................................................................................ 8 4.1.1. Limit ............................................................................................................................................................ 8 4.1.2. Test Procedures ........................................................................................................................................... 8 4.1.3. Test Result ................................................................................................................................................... 9 - Page 3 of 9 - Report No.: HB20260616001E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com TEST RESULT CERTIFICATION Applicant’s Name ................. : ATLANTA SYSTEMS PVT. LTD. Address ................................. : M-135, 2nd FLOOR, CONNAUGHT PLACE NEW DELHI-110001 Manufacturer's Name .......... : ATLANTA SYSTEMS PVT. LTD. Address ................................. : M-135, 2nd FLOOR, CONNAUGHT PLACE NEW DELHI-110001 Product description Product name ........................ : Bluetooth Tracker Model Number ....................... : LOCATO 101 Standards ............................. : FCC CFR 47 PART 1 , 1.1310 Test procedure ....................... : KDB 447498 D01 General RF Exposure Guidance v06 This device described above has been tested by Shenzhen HongBiao Certification& Testing Co., Ltd and the test results show that the equipment under test (EUT) is in compliance with the EMC requirements. And it is applicable only to the tested sample identified in the report. Date of Test ........................................... : Date (s) of performance of tests ............. : June 16, 2026~June 22, 2026 Test Result .............................................. : Pass Testing Engineer : ( Z o e Su) Technical Manager : (M i n g L i u) Authorized Signatory : (L e o S u) - Page 4 of 9 - Report No.: HB20260616001E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Revision History Revised No. Date of Issue Description 01 June 22, 2026 Original - Page 5 of 9 - Report No.: HB20260616001E-02 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com 1 General Description 1.1 Description of EUT Product name: Bluetooth Tracker Model name: LOCATO 101 Series Model: N/A Different of series model: N/A Operation frequency: 2402-2480MHz Modulation type: GFSK Bit Rate of …

Text truncated - open the document above for the full version.

2.4GHz 3216 Chip Antenna: RANT3216F245C03 _ Application: WLAN,802.11b/g,Bluetooth,WLAN,etc... Features SMD,highreliability,ultraImpact,Omni-directional... PartnumberInformation RANT3216F245C03 (A) (B) (C) (D)(E) (F) Electrical Specification The specification is defined on EVB. Dimension and Terminal Configuration No.Terminal Name 1Feeding/GNG 2GND/Feeding (A)Product TypeChip Antenna (B) Size Code 3.2x1.6mm( ± 0.2mm) (C) MaterialHigh K material (D) Frequency2.4 ~ 2.5GHz (E) Feeding modePIFA & Single Feeding (F) Antenna typeType=03 Working Frequency Range2400 ~2500 MHz Bandwidth120 MHz (Min.) Peak GaindBi (Typ. 1.24 ) Impedance50 Ohm Return loss10 dB ( Min) PolarizationLinear Azimuth BeamwidthOmni-directional Operation Temperature(°C)-40 ~85°C Resistance to Soldering Heats 10sec. ( @ 280°C) TerminationNi / Au (Leadless) Dimension (mm) L 3.20±0.20 W 1.60±0.20 T 0.45±0.20 RAIN International Technology Co., Ltd. Building F, 709, Yuxing Technology Industrial Park, Nanchang Third Industrial Zone, Xiangxiang Sub-district, Bao'an District, Shenzhen City 2.4GHz 3216 Chip Antenna: RANT3216F245C03 _ 1 Evaluation BoardReference PCB Dimension Antenna Layout Reference Unit :mm Electrical Characteristics Return Loss & Radiation Return Loss Frequency(MHz) S11 (dB) 2400-10.50 2450-30.62 2500-11.47 2.4GHz 3216 Chip Antenna: RANT3216F245C03 _ Radiation 2400MHz2450MHz2500MHz Efficiency82.52%85.26%83.01% Peak Gain1.15 dBi1.24 dBi1.19 dBi Directivity1.89 dBi1.97 dBi1.91 dBi X Y Z 2400MHz 2450MHz 2500MHz 2.4GHz 3216 Chip Antenna: RANT3216F245C03 _ Taping Specifications Reel and Taping Specification Reel Specification TYPESIZEABCD 32167”5K/Reel 9.0±0.5 60±213.5±0.5178±2 Tapping Specification PackagingTypeABWEFGHTψDP Paper Type3216 1.90±0.2 0 3.50±0.2 0 8.0±0.2 0 1.75±0.1 0 3.5±0.054.0±0.102.0±0.050.75±0.1 0 1.50±0.1 0 4.0±0.1 2.4GHz 3216 Chip Antenna: RANT3216F245C03 _ Reliability Table Test ItemProcedure Requirements Ceramic Type Remark (Reference) Electrical Characterization Fulfill the electrical specification User Spec. Thermal Shock 1. Preconditioning: 50 ± 10°C/ 1 hr , then keep for 24 ± 1 hrs at room temp. 2. Initial measure: Spec: refer Initialspec. 3. Rapid change of temperature test: -30°Cto +85°C; 100 cycles; 15 minutes at Lower category temperature; 15 minutes at Upper category temperature. No Visible Damage. Fulfill the electrical specification. MIL-STD-202 107 Temperature Cycling 1. Initial measure: Spec: refer Initialspec. 2. 100 Cycles (-30°Cto +85°C), Soak Mode=1 (2 Cycle/hours). 3. Measurement at 24 ± 2Hours after testcondition. No Visible Damage. Fulfill the electrical specification. JESD22 JA104 High Temperature Exposure 1. Initial measure: Spec: refer Initialspec. 2. Unpowered; 500hours @ T=+85°C. 3. Measurement at 24 ± 2 hours aftertest. No Visible Damage. Fulfill the electrical specification. MIL-STD-202 108 Low Temperature Storage 1. Initial measure: Spec: refer Initialspec. 2. Unpowered: 500hours @ T=-30°C. 3. Measurement at 24 ± 2 hours aftertest. No Visible Damage. Fulfill the electrical specification. MIL-STD-202 108 Solderability (SMD Bottom Side) Dipping method: a. Temperature: 235 ±5°C b. Dipping time: 3 ±0.5s The solder should cover over 95% of the critical area of bottom side. IEC 60384-21/22 4.10 Soldering Heat Resistance (RSH) Preheating temperature: 150 ± 10°C. Preheating time: 1~2 min. Solder temperature: 260 ± 5°C. Dipping time: 5 ± 0.5s No Visible Damage.IEC 60384-21/22 4.10 Vibration5g's for 20 min., 12 cycles each of 3 orientations Note: Use 8"X5" PCB .031" thick 7 secure points on, one long side and 2 secure points at corners of opposite sides. Parts mounted within 2" from any secure point. Test from 10-2000 Hz. No Visible Damage.MIL-STD-202 Method 204 Mechanical Shock Three shocks in each direction shall be applied along the three mutually perpendicular axes of the test specimen (18 shocks) Peak value: 1,500g’s Duration: 0.5ms Velocity change: 15.4 ft/s Waveform: Half-sine No Visible Damage.MIL-STD-202 Method 213 Humidity Bias 1. Humidity: 85% R.H., Temperature:85 ± 2 °C. 2. Time: 500 ± 24hours. 3. Measurement at 24 ± 2hrs after testcondition. No Visible Damage. Fulfill the electrical specification. MIL-STD-202 Method 106 2.4GHz 3216 Chip Antenna: RANT3216F245C01 _ Board Flex (SMD) 1. Mounting method: IR-Reflow. PCB Size (L:100 × W:40 × T:1.6mm) 2. Apply the load in direction of the arrow until bending reaches 2 mm. No Visible Damage.AEC-Q200 005 AdhesionForce of 1.8Kg for 60 seconds.No Visible Damage Magnification of 20X or greater may be employed for inspection of the mechanical integrity of the device body terminals and body/terminal junction. AEC-Q200 006 Physical Dimension Any applicable method using x10 magnification, micrometers, calipers, gauges, contour projectors, or other measuring equipment, capable of determining the actual specimen dimensions. In accordance with specification. JESD22 JB100 Revision History RevisionDateContent 12019/03/01New Datasheet 22020/02/22Add 2D radiation characteristic

- Page 1 of 50 - Report No.: HB20260616001E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Test Report Product: Bluetooth Tracker Trade Mark: ATLANTA Model Number: LOCATO 101 FCC ID: 2BWNX-LOCATO Prepared for ATLANTA SYSTEMS PVT. LTD. M-135, 2nd FLOOR, CONNAUGHT PLACE NEW DELHI-110001 Prepared by Shenzhen HongBiao Certification& Testing Co., Ltd Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen, China Tel.: +86-755-2998 9321 Fax.: +86-755-2998 5110 Website: http://www.sz-hongbiao.com - Page 2 of 50 - Report No.: HB20260616001E-01 Add:Room 102, 201, Building 2, Yuanwanggu RFID Industrial Park, Tongguan Road, Tianliao Community, Yutang Street, Guangming District, Shenzhen,China Tel: (86-755) 29989321 Fax: (86-755) 29985110 Web:www.sz-hongbiao.com Table of Contents 1 GENERAL DESCRIPTION ..................................................................................................................................... 6 1.1 DESCRIPTION OF EUT ................................................................................................................................................ 6 1.2 TEST MODE .............................................................................................................................................................. 6 1.3 OPERATION CHANNEL LIST ........................................................................................................................................... 6 1.4 TEST SETUP .............................................................................................................................................................. 7 1.5 POWER SETTING CONFIGURATION PARAMETERS ............................................................................................................... 7 1.6 ANCILLARY EQUIPMENT .............................................................................................................................................. 7 2 SUMMARY OF TEST RESULT ............................................................................................................................... 8 3 TEST FACILITIES AND ACCREDITATIONS .............................................................................................................. 9 3.1 TEST LABORATORY ..................................................................................................................................................... 9 3.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 9 3.3 MEASUREMENT UNCERTAINTY ..................................................................................................................................... 9 3.4 TEST SOFTWARE ...................................................................................................................................................... 10 4 LIST OF TEST EQUIPMENT .................................................................................................................................11 5 TEST ITEM AND RESULTS ...................................................................................................................................13 5.1 ANTENNA REQUIREMENT .......................................................................................................................................... 13 5.1.1 Standard Requirement ............................................................................................................................. 13 5.1.2 Test Result ................................................................................................................................................. 13 5.2 CONDUCTED EMISSION ............................................................................................................................................. 14 5.2.1 Limits ........................................................................................................................................................ 14 5.2.2 Test Procedures ......................................................................................................................................... 14 5.2.3 Test Setup .................................................................................................................................................. 15 5.2.4 Test Result ................................................................................................................................................. 15 5.3 RADIATED EMISSION ................................................................................................................................................ 16 5.3.1 Limits ........................................................................................................................................................ 16 5.3.2 Test Procedures ......................................................................................................................................... 16 5.3.3 Test Setup .................................................................................................................................................. 16 5.3.4 Test Result ................................................................................................................................................. 17 5.3.5 Band Edge - Radiated ............................................................................................................................... 21 5.3.6 Spurious emission in band 1000MHz-25000MHz .................................................................................... 22 5.4 PEAK OUTPUT POWER ....................…

Text truncated - open the document above for the full version.

- Page 1 of 1 - Photographs of the Test Setup Model: LOCATO 101 Radiated Emission Below 1GHz Radiated Emission Above 1GHz