2BWQW-JG398Remote Control for JG-398 selfie stick

1.将手机固定在手机支架上，长按拍照键3秒至绿灯闪烁开启蓝牙配 对模式。 2.打开手机蓝牙设置，搜索并连接“JG-398”，成功后绿灯长亮。3 按下自拍杆的拍照键进行拍照，再次长按拍照键3秒，则关闭自拍支 架电源，同时关闭蓝牙配对模式。 JG-398 注意:自拍支架默认连接已配对成功的手机，如您需要更换连接手机设 备，请先在已连接的手机上取消蓝牙配对，再连接配对新设备。 开机方式：：长按开机键2秒开机，长按拍照键2秒，绿色指示灯长亮3秒进入回连状 态，回连不成功进入广播状态指示灯绿色闪烁，3分钟后进入休眠。 关机方式：：开机及休眠状态下，长按开机键3秒绿灯闪3次关机，休眠15分钟后绿灯 闪三次自动关机。 已配对连接状态：绿色指示灯长亮5秒后熄灭。 无配对连接状态：绿色指示灯闪烁。 休眠唤醒： 休眠状态下，短按一下拍照键，拍照指示灯亮一下，然后进入回连／广播 闪烁状态。 开机自动配对：开机后，如上一次已配对手机蓝牙是打开状态，直接自动连接。 休眠唤醒后自动配对：休眠唤醒后，如上一次已配对手机蓝牙是打开状态，直接自 动连接。 拍照：短按拍照键／摄像，绿灯亮一下。 手机删除连接：遥控器与手机处于连接状态时，在手机里面取消遥控器配对，遥控 器直接进入休眠。 距离过远断开：遥控器与手机处于连接状态时，遥控器或手机距离过远断开后，遥 控器直接进入休眠。 连接时关闭手机蓝牙：遥控器与手机处于连接状态时，关闭手机的蓝牙，遥控器直 接进入休眠。 连接后无操作时间：手机与遥控器连接后，不拍照5分钟后，自动进入休眠，休眠 15分钟后绿灯闪三次自动关机。 低电指示：1．电量低于2.6V每次开机，无配对时配对或回连，配对成功后绿灯常亮 5s后红灯闪烁5次，频率为1s／次，然后熄灭。 2．工作状态时，每次操作红灯亮起替代绿灯操作反馈。 功耗要求：静态电流小于1UA 蓝牙名称：JG-398 电池容量：55mAh 蓝牙版本：4.2以上版本 充电电压: 5V/1A 充电时间: 3小时 按键个数：2个 指示灯个数：1个 距离要求：10M内有效 用卡针或适当工具插入遥控器底部针孔，取下电池盖，更换电池，然 后装回电池盖。 取出遥控器 提示： A：安装电池时请注意电池正极朝外。 Type-C 部件名称 自拍支架 包装配件 Pb 铅 Hg 汞 Cd 镉 Cr(VI) 六价铬 PBBs 多溴联苯 PBDEs 多溴联苯醚 本表依据SJ/T11364的规定编制。 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 GB/T26572标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GB/T26572标准规定的限量要求，为保护人类环境和人类健康。 1：本产品报废后请将其与生活垃圾分开，消费者有责任将其送至有 资质的回收点。 2：回收中心将通过适当的方法回收再利用产品中的材料。 3：关于本产品回收处理的详细信息，请咨询当地政府、废品处理中 心或经销商。 落地开三脚架自拍杆 【JG-398 冷靴版】 颠覆性专利 落地自动弹开 使用说明书 冷靴盖 冷靴口 手机夹 转动头 铝合金 拉杆 手柄套 手机支架拉手 拍照/开关键 关机遥控键 三脚支架 合拢时一只手握住自拍杆中部位置，另一只手将拉杆逐节推回手柄 套简内。 垂 直 落 下 首先将手机支架拉手向上拉出，然后垂直地平面大约10cm高度落下 ，即可自动弹开自拍杆三脚架。 当三角架伸开后，按动自拍杆上一个按键滑动可以锁紧三角架 将手机横向倾斜45度，放入手机支架上，轻轻用力往上推，手机即 可固定在支架上。 可锁三角架 本产品采用专利滑轨式手机支架，预留前后倾，左右旋转空间，不 取手机也可以横竖屏自由切换。 顶盖 冷靴口 冷靴口扩展安装： 旋转打开顶盖，将适配的补光灯等设备 安装到冷靴口。 产品名称:落地开三脚架自拍杆 产品材料:ABS+PC/铝 产品型号:JG-398电池类型:锂锰纽扣电池 整机尺寸:331*43.36*38.24mm 产品重量:380g 连接方式:蓝牙 电池容量：110 MAH 遥控距离:10m 支持系统:Android/I0S/HarmonyOS 售后服务承诺：所有官方渠道及官方授权渠道出售的商品，将严格根据 《中华人民共和国消费者权益保护法》及现行有效的法律法规，对于执 行特殊三包条约的地区，承诺遵守当地的相关规定提供售后服务。为了 保障您的权益，请您在购买产品后妥善保管保修卡和有效购买凭证。 用户信息 姓名： 联系电话： 购买日期： 购买平台及店铺名： 订单号： 产品信息 产品型号： 服务热线： 本说明书中的图片及文字解释权（中国） 落地开 PASS Bluetooth connect to 1. Fix the phone on the phone holder, and long press the shutter button for 3 seconds until the green light flashes to enable Bluetooth pairing mode. 2. Open the phone's Bluetooth settings, search for and connect to "JG-398". The green light will stay on once connected. 3. Press the button on the selfie stick to take a photo. Long press the shutter button again for 3 seconds to turn off the selfie stick's power and disable Bluetooth pairing mode JG-398 Remote control function description;Remote control operation guidetion;Function description;Feature description Power consumption requirement: static current less than 1UA Bluetooth name: JG-398 Battery capacity: 55mAh Bluetooth: 4.2 or above Charging voltage: 5V/1A Charging time: 3hour Number of buttons: 2 Number of lights: 1 Distance requirement: effective within 10M Take out the remote control Get the remote control Type-C Part name Component name selfie stick selfie stand selfie tripod Packaging accessories; Packing accessories Pb Lead Hg Mercury Cd Cadmium Cr(VI) Hexavalent chromium PBBs Polybrominated biphenyls This table is prepared in accordance with the provisions of SJ/T 11364. O: Indicates that the content of the hazardous in all homogeneous materials of the component is below the limit requirements specified in the GB/T 26572 standard. X: Indicates that the content of the hazardous in at least one homogeneous material of the component exceeds the limit requirements specified in the GB/T 26572 standard, in order to protect the human environment and human. 1: After this product is discarded, please separate it from domestic waste. Consumers are responsible for delivering it to a qualified recycling point. 2: The recycling center recover and reuse the materials in the product through appropriate methods. 3: For detailed information regarding the recycling and disposal of this product, please consult your local government, waste disposal center or dealer. Note: The selfie stick connects to the successfully paired phone by default. If you need to change the connected phone, please first unpair the Bluetooth on the currently connected phone, and then pair it with the new device. Power on method: Long press the power button for 2 seconds to power on, long press the shutter button for 2, the green indicator light stays on for 3 seconds to enter reconnection mode, if reconnection fails, it enters broadcasting mode with the green indicator light flashing, and enters sleep mode after3 minutes. Power off method: In power-on or sleep mode, long press the power button for 3 seconds, the green light flashes 3 times to power off after 15 minutes of sleep, the green light flashes 3 times and it automatically powers off. Paired and connected state: The green indicator light stays on for seconds and then turns off. Unpaired and unconnected state: The green indicator light flashes. Wake up from sleep: In sleep mode, short press the shutter button, the indicator light flashes once, and then it enters the reconnection/broadcasting flashing state. Automatic pairing on power-on: After powering on, if the Bluetooth of the previously paired is on, it connects automatically. Automatic pairing after waking up from sleep: After waking up from sleep, if the Bluetooth of the previously paired phone is on, it connects automatically Taking photos: Short press the shutter button/video, the green light flashes once. Phone deletes connection: When the remote control and the phone are connected, unpair the remote control on the phone, and the remote control directly enters sleep mode. Disconnect due to excessive distance: When the remote control and the phone are connected, if the distance between the control and the phone is too far and they disconnect, the remote control directly enters sleep mode. Turning off phone Bluetooth during connection: When the remote control and the phone are connected turn off the phone's Bluetooth, and the remote control directly enters sleep mode. Inactivity time after connection: After the phone and the remote…

Text truncated - open the document above for the full version.

Zhongcheng Precision (Dongguan) Co., Ltd. Covered Equipment Certification Attestation Letter 6/23/2026 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2BWQW-JG398 Zhongcheng Precision (Dongguan) Co., Ltd. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. Zhongcheng Precision (Dongguan) Co., Ltd. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Zhongcheng Precision (Dongguan) Co., Ltd. (“the applicant”) certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). <Signature>: Name: Jack Bu Title: Manager Company: Zhongcheng Precision (Dongguan) Co., Ltd. Date: 6/23/2026

Zhongcheng Precision (Dongguan) Co., Ltd. * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter 6/23/2026 TO: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 ATTN.: Reviewing Engineer FCC ID: 2BWQW-JG398 FRN of applicant: 0038576948 Per section 2.911(d)(7) of the FCC rules, [Zhongcheng Precision (Dongguan) Co., Ltd.] (“the applicant”) certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process: Company Name: Herland International Trading Inc FCC Registration Number (FRN): 0036324101 Physical U.S. Company Address: 1370 Valley Vista Dr Ste 200 Diamond Bar, CA 91765 Contact Person: Jianfeng Gao Agent Email Address: [email protected] The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Signed: Printed name: Jack bu Title: Manager Company Name: Zhongcheng Precision (Dongguan) Co., Ltd. Date: 6/23/2026 Agent Signed (if different from Applicant): Signed: Printed name: Jianfeng Gao Title: Manager Company Name: Herland International Trading Inc Date: 6/23/2026

Zhongcheng Precision (Dongguan) Co., Ltd. 2026-06-23 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Shenzhen DL Testing Technology Co., Ltd.（101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China）to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with Zhongcheng Precision (Dongguan) Co., Ltd.（Room 101, Building 11, No. 2, Xianghe 1st Road, Dalang Town, Dongguan City, Guangdong Province） <Signature>: Name: Jack Bu Title: Manager Company: Zhongcheng Precision (Dongguan) Co., Ltd.

Zhongcheng Precision (Dongguan) Co., Ltd. 2026-06-23 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Compliance Testing, LLC to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). Sincerely, <Signature>: Name: Jack Bu Title: Manager Company: Zhongcheng Precision (Dongguan) Co., Ltd.

Zhongcheng Precision (Dongguan) Co., Ltd. 2026-06-23 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BWQW-JG398 Product Name: Remote Control for JG-398 selfie stick Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...)  Schematics  Block diagram  Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature>: Name: Jack Bu Title: Manager Company: Zhongcheng Precision (Dongguan) Co., Ltd.

Zhongcheng Precision (Dongguan) Co., Ltd. FCC ID: 2BWQW-JG398 Product Similarity Declaration Applicant: Zhongcheng Precision (Dongguan) Co., Ltd. Address: Room 101, Building 11, No. 2, Xianghe 1st Road, Dalang Town, Dongguan City, Guangdong Province Manufacturer: Zhongcheng Precision (Dongguan) Co., Ltd. Address: Room 101, Building 11, No. 2, Xianghe 1st Road, Dalang Town, Dongguan City, Guangdong Province Product Name: Remote Control for JG-398 selfie stick Trade Mark: N/A Model Number: JG-398, JG-398-1, JG-398-2, JG-398-3, JG-398-4, JG-398-5, JG-398-6, JG-398-7, JG-398-8, JG-398-9, JG-398-10, JG-398-11, JG-398-12, JG-398-13, JG-398-15, JG- 398-16, JG-398-17, JG-398-18, JG-398-19, JG-398-20 We (Zhongcheng Precision (Dongguan) Co., Ltd.) hereby state that all the models are electrical identical including the same software parameter and hardware design (i.e., circuit design, PCB Layout, RF module/circuit, antenna type(s) and antenna location, components on PCB, etc.,), same mechanical structure and design (including product enclosure, materials, etc.,), All models are the same as the samples except for the model name, appearance color. Name: Jack bu Title: Manager Telephone: 18906679427 Email: [email protected]

Shenzhen DL Testing Technology Co., Ltd. EUT PHOTO(External Photos) Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. ※※※※※ END OF REPORT ※※※※※

Size:15*10mm M/N: JG-398 FCC ID: 2BWQW-JG398 Label location

Shenzhen DL Testing Technology Co., Ltd. EUT PHOTO(Internal Photos) Shenzhen DL Testing Technology Co., Ltd. ANT Shenzhen DL Testing Technology Co., Ltd. ※※※※※ END OF REPORT ※※※※※

FCC ID: 2BWQW-JG398 RF Exposure Evaluation According to KDB 447498 D01 V06 and part 2.1093，Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition(s), listed below, is (are) satisfied. For 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f (GHz) ] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extremity SAR, where f (GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison EIRP=E Meas +20log(d Meas )-104.7 EIRP is the equivalent isotropically radiated power, in dBm E Meas is the field strength of the emission at the measurement distance, in dBμV/m d Meas is the measurement distance, in m Here, Conducted output power (dBm) Max tune-up (mW) Frequency (MHz) Min. distance(mm) Calc. thresholds limit 1.38 1.37 2402 5 0.43 3.0 So a SAR test is not required

Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 1 of 18 FCC ID: 2BWQW-JG398 Applicant: Zhongcheng Precision (Dongguan) Co., Ltd. Address: Room 101, Building 11, No. 2, Xianghe 1st Road, Dalang Town, Dongguan City, Guangdong Province Manufacturer: Zhongcheng Precision (Dongguan) Co., Ltd. Address: Room 101, Building 11, No. 2, Xianghe 1st Road, Dalang Town, Dongguan City, Guangdong Province Product Name: JG-398 selfie stick Trade Mark: N/A Model Number: JG-398, JG-398-1, JG-398-2, JG-398-3, JG-398-4, JG-398-5, JG-398-6, JG-398-7, JG- 398-8, JG-398-9, JG-398-10, JG-398-11, JG-398-12, JG-398-13, JG-398-15, JG-398-16, JG-398-17, JG-398-18, JG-398-19, JG-398-20 Date of Receipt: Jun. 04, 2026 Test Date: Jun. 04, 2026 - Jun. 17, 2026 Date of Report: Jun. 17, 2026 Prepared By: Shenzhen DL Testing Technology Co., Ltd. Address: 101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China Applicable Standards: FCC PART 15 C 15.247 ANSI C63.10:2020 Test Result: Pass Report Number: DLE-260604017R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 2 of 18 1. Bandwidth 1.1 Test Result 1.1.1 OBW Mode TX Type Frequency (MHz) ANT 99% Occupied Bandwidth (MHz) Verdict Result Limit 1M SISO 2402 1 1.040 / Pass 2440 1 1.039 / Pass 2480 1 1.042 / Pass 1.1.2 6dB BW Mode TX Type Frequency (MHz) ANT 6dB Bandwidth (MHz) Verdict Result Limit 1M SISO 2402 1 0.670 >=0.5 Pass 2440 1 0.668 >=0.5 Pass 2480 1 0.663 >=0.5 Pass Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 3 of 18 1.2 Test Graph 1.2.1 OBW 1M_LCH_2402MHz_Ant1_NTNV 1M_MCH_2440MHz_Ant1_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 4 of 18 1M_HCH_2480MHz_Ant1_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 5 of 18 1.2.2 6dB BW 1M_LCH_2402MHz_Ant1_NTNV 1M_MCH_2440MHz_Ant1_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 6 of 18 1M_HCH_2480MHz_Ant1_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 7 of 18 2. Maximum Conducted Output Power 2.1 Test Result 2.1.1 Power Mode TX Type Frequency (MHz) Maximum Peak Conducted Output Power (dBm) Verdict ANT1 Limit 1M SISO 2402 1.38 <=30 Pass 2440 0.38 <=30 Pass 2480 -0.96 <=30 Pass Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 8 of 18 2.2 Test Graph 2.2.1 Power 1M_LCH_2402MHz_Ant1_NTNV 1M_MCH_2440MHz_Ant1_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 9 of 18 1M_HCH_2480MHz_Ant1_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 10 of 18 3. Maximum Power Spectral Density 3.1 Test Result 3.1.1 PSD Mode TX Type Frequency (MHz) Maximum PSD (dBm) Verdict ANT1 Limit 1M SISO 2402 -15.07 <=8 Pass 2440 -15.98 <=8 Pass 2480 -17.26 <=8 Pass Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 11 of 18 3.2 Test Graph 3.2.1 PSD 1M_LCH_2402MHz_Ant1_NTNV 1M_MCH_2440MHz_Ant1_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 12 of 18 1M_HCH_2480MHz_Ant1_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 13 of 18 4. Unwanted Emissions In Non-restricted Frequency Bands 4.1 Test Result 4.1.1 Ref Mode TX Type Frequency (MHz) ANT Level of Reference (dBm) 1M SISO 2402 1 1.24 2440 1 0.21 2480 1 -1.12 Note1: Refer to FCC Part 15.247 (d) and ANSI C63.10-2020, the channel contains the maximum PSD level was used to establish the reference level. 4.1.2 CSE Mode TX Type Frequency (MHz) ANT Level of Reference (dBm) Limit (dBm) Verdict 1M SISO 2402 1 1.24 -18.76 Pass 2440 1 0.21 -19.79 Pass 2480 1 -1.12 -21.12 Pass Note1: Refer to FCC Part 15.247 (d) and ANSI C63.10-2020, the channel contains the maximum PSD level was used to establish the reference level. Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 14 of 18 4.2 Test Graph 4.2.1 Ref 1M_LCH_2402MHz_Ant1_NTNV 1M_MCH_2440MHz_Ant1_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 15 of 18 1M_HCH_2480MHz_Ant1_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 16 of 18 4.2.2 CSE 1M_LCH_2402MHz_Ant1_NTNV 1M_LCH_2402MHz_Ant1_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 17 of 18 1M_MCH_2440MHz_Ant1_NTNV 1M_HCH_2480MHz_Ant1_NTNV Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 18 of 18 1M_HCH_2480MHz_Ant1_NTNV

Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-260604017R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 1 of 27 FCC Part 15C Test Report FCC ID: 2BWQW-JG398 Applicant: Zhongcheng Precision (Dongguan) Co., Ltd. Address: Room 101, Building 11, No. 2, Xianghe 1st Road, Dalang Town, Dongguan City, Guangdong Province Manufacturer: Zhongcheng Precision (Dongguan) Co., Ltd. Address: Room 101, Building 11, No. 2, Xianghe 1st Road, Dalang Town, Dongguan City, Guangdong Province Product Name: Remote Control for JG-398 selfie stick Trade Mark: N/A Model Number: JG-398, JG-398-1, JG-398-2, JG-398-3, JG-398-4, JG-398-5, JG-398-6, JG-398-7, JG-398-8, JG-398-9, JG-398-10, JG-398-11, JG-398-12, JG-398-13, JG-398-15, JG-398-16, JG-398-17, JG-398-18, JG-398-19, JG-398-20 Date of Receipt: Jun. 04, 2026 Test Date: Jun. 04, 2026 - Jun. 17, 2026 Date of Report: Jun. 17, 2026 Prepared By: Shenzhen DL Testing Technology Co., Ltd. Address: 101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China Applicable Standards: FCC PART 15 C 15.247 ANSI C63.10:2020 Test Result: Pass Report Number: DLE-260604017R Prepared (Test Engineer): Alisa Song Reviewer (Supervisor): Jack Bu Approved (Manager): Jade Yang This test report is based on a single evaluation of one sample of above mentioned products. It is not permitted to be duplicated in extracts without written approval of Shenzhen DL Testing Technology Co., Ltd. Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-260604017R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 2 of 27 Table of Contents Page 1. . SUMMARY OF TEST RESULTS 4 1.1. MEASUREMENT UNCERTAINTY 4 2. . GENERAL INFORMATION 5 2.1. GENERAL DESCRIPTION OF EUT 5 2.2. DESCRIPTION OF TEST MODES 6 2.3. BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 6 2.4. DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 7 2.5. TABLE OF PARAMETERS OF TEST SOFTWARE SETTING 7 2.6. EQUIPMENTS LIST FOR ALL TEST ITEMS 8 3. . EMC EMISSION TEST 9 3.1. CONDUCTED EMISSION MEASUREMENT 9 3.1.1. POWER LINE CONDUCTED EMISSION LIMITS 9 3.1.2. TEST PROCEDURE 9 3.1.3. DEVIATION FROM TEST STANDARD 9 3.1.4. TEST SETUP 10 3.1.5. EUT OPERATING CONDITIONS 10 3.1.6. TEST RESULTS 11 3.2. RADIATED EMISSION MEASUREMENT 13 3.2.1. RADIATED EMISSION LIMITS 13 3.2.2. TEST PROCEDURE 14 3.2.3. DEVIATION FROM TEST STANDARD 14 3.2.4. TEST SETUP 14 3.2.5. EUT OPERATING CONDITIONS 15 3.2.6. TEST RESULTS (BETWEEN 9KHZ – 30 MHZ) 16 3.2.7. TEST RESULTS (BETWEEN 30MHZ – 1GHZ) 17 3.2.8. TEST RESULTS (1GHZ~25GHZ) 19 3.3 RADIATED BAND EMISSION MEASUREMENT 20 3.3.1 TEST REQUIREMENT: 20 3.3.2 TEST PROCEDURE 20 3.3.3 DEVIATION FROM TEST STANDARD 20 3.3.4 TEST SETUP 21 3.3.5 EUT OPERATING CONDITIONS 21 3.4 CONDUCTED BAND EDGE EMISSION&CONDUCTED SPURIOUS EMISSIONS MEASUREMENT 23 3.4.1 APPLICABLE STANDARD 23 3.4.2 TEST PROCEDURE 23 3.4.3 DEVIATION FROM STANDARD 23 3.4.4 TEST SETUP 23 Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-260604017R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 3 of 27 Table of Contents Page 3.4.5 EUT OPERATION CONDITIONS 23 3.4.6 TEST RESULTS 23 4. . PEAK OUTPUT POWER 24 4.1. APPLIED PROCEDURES / LIMIT 24 4.1.1. TEST PROCEDURE 24 4.1.2. DEVIATION FROM STANDARD 24 4.1.3. TEST SETUP 24 4.1.4. EUT OPERATION CONDITIONS 24 4.1.5. TEST RESULTS 24 5. . POWER SPECTRAL DENSITY TEST 25 5.1. APPLIED PROCEDURES / LIMIT 25 5.1.1. TEST PROCEDURE 25 5.1.2. DEVIATION FROM STANDARD 25 5.1.3. TEST SETUP 25 5.1.4. EUT OPERATION CONDITIONS 25 5.1.5. TEST RESULTS 25 6. . 6DB BANDWIDTH TEST 26 6.1. APPLIED PROCEDURES / LIMIT 26 6.1.1. TEST PROCEDURE 26 6.1.2. DEVIATION FROM STANDARD 26 6.1.3. TEST SETUP 26 6.1.4. EUT OPERATION CONDITIONS 26 6.1.5. TEST RESULTS 26 7. . ANTENNA REQUIREMENT 27 7.1. STANDARD REQUIREMENT 27 7.2. EUT ANTENNA 27 8. . TEST SEUUP PHOTO 27 9. . EUT PHOTO 27 Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-260604017R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 4 of 27 1.. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15 (15.247) , Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS 15.205, 15.209, 15.247(d) Radiated Spurious Emission PASS 15.209, 15.205 Band Edge Emission PASS 15.247(b) Peak Output Power PASS 15.247(a)(2) 6dB Bandwidth PASS 15.247(e) Power Spectral Density PASS 15.203 Antenna Requirement PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report Test lab: Shenzhen DL Testing Technology Co., Ltd. Address: 101-201, Comprehensive Building, Tongzhou Electronics Longgang Factory Area, No.1 Baolong Fifth Road, Baolong Community, Baolong Street, Longgang District, Shenzhen, China FCC Test Firm Registration Number: 854456 Designation Number: CN1307 IC Registered No.: 27485 CAB ID.: CN0118 1.1. MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission Test ±2.56dB 2 RF power,conducted ±0.42dB 3 Spurious emissions,conducted ±2.76dB 4 All emissions,radiated(<1G) ±3.65dB 5 All emissions,radiated(>1G) ±4.89dB 6 Temperature ±0.5°C 7 Humidity ±2% 8 6dB Bandwidth ±0.2MHz 9 Power Spectral Density ±0.3dBm Shenzhen DL Testing Technology Co., Ltd. Report No.: DLE-260604017R Test Report Tel: 400-688-3552 Web:www.dl-cert.com Email: [email protected] Page 5 of 27 2.. GENERAL INFORMATION 2.1. GENERAL DESCRIPTION OF EUT Product Name: Remote Control for JG-398 selfie stick Trade Mark: N/A Model Number: JG-398, JG-398-1, JG-398-2, JG-398-3, JG-398-4, JG-398-5, JG-398-6, JG-398-7, JG-398-8, JG-398-9, JG-398-10, JG-398-11, JG-398-12, JG-398-13, JG-398-15, JG-398-16, JG-398-17, J…

Text truncated - open the document above for the full version.

Antenna Test Report DIAN1B 东莞市勤睿科技有限公司 Dongguan Qinrui Technology Co., Ltd 广东省东莞市长安镇振安西路 263 号 4 楼 4th Floor, No. 263, Zhen'an West Road, Chang'an Town, Dongguan City, Guangdong Province 1. AntennaplateDescription: Antennapeakgain0dBi(Max) Frequencyrange2402Mhz 2. Pictureof Antenna 3.AntennaRadiationPattern HorizontalVertical FrequencyGainFrequencyGain 2402Mhz0dBi2402Mhz-2.4dBi 。 270 90 一Vertical(2402MHZ) 180

Shenzhen DL Testing Technology Co., Ltd. EUT TEST PHOTO Radiated Measurement Photos Shenzhen DL Testing Technology Co., Ltd. Conducted Measurement Photos ※※※※※ END OF REPORT ※※※※※