2BWYH-UC60M62-RX60 GHz Full-Duplex Wireless Communication Module

Uniqconn Inc. 071426-19 Certification Application Attestation Statements Date: August 5, 2026 American Certification Body, Inc. 3060 Williams Drive, Suite 300 #104 Fairfax, VA 22031 FCC ID: 2BWYH-UC60M62-RX To Whom It May Concern: Statement for 47 CFR section 2.911(d)(5)(i) _____ Uniqconn Inc._______ certifies that as of the date of the application the equipment for which authorization is sought is not “covered” equipment 1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not “covered” equipment. Additional Explanation: <N/A> Statement for 47 CFR section 2.911(d)(5)(ii) ______ Uniqconn Inc.______ (“the applicant”) certifies that, as of the date of the filing of this application, the applicant ☐ - is / ☑ - is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates – see KDB 986446 Question 5) as an entity producing “covered” equipment. The applicant also certifies that the device does not have cybersecurity and/or anti-virus software produced by Kaspersky Lab, Inc or any of its successors and assignees identified on the covered list installed on the device, nor will it be installed by the applicant at any time after certification. Thank you, By: __________________________ KWANGIL CHOI (Signature 2 ) (Print name) Title: Hardware Engineer Company: Uniqconn Inc. Telephone: +82-507-1377-2627 1 - The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist . 2 - Letters must be placed on appropriate letterhead.

Uniqconn Inc. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 08-05-2026 Ref: Attestation Statements Part 2.911(d)(7) Filing Grantee Code: 2BWYH FCC ID: 2BWYH-UC60M62-RX Applicant FRN: 0038629978 Uniqconn Inc. certifies that, as of the date of the filing of the application, FCC US Agent, LLC is our designated U.S. agent for service of process for the above referenced FCC ID. Uniqconn Inc. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. FCC US Agent, LLC accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Name: FCC US Agent, LLC U.S. Agent FRN: 0033402884 Address: 3722 Illinois Avenue, Saint Charles, IL 60174, USA Contact Person: Tim Payne Tel.: (708) 571-3148 Email: [email protected] Sincerely, Uniqconn Inc. FCC US Agent, LLC KWANGIL CHOI Tim Payne [Insert Applicant signature] [Insert U.S. Agent signature]

Uniqconn Inc. 070920-02b Request for Modular/Limited Modular Approval Date: August 11, 2026 Subject: Manufacturer’s Declaration for ☒ - Modular Approval ☐ - Split Modular Approval ☐ - Limited Modular Approval ☐ - Limited Split Modular Approval Confidentiality Request for: FCC ID: 2BWYH-UC60M62-RX 8 Basic Requirements – FCC Part 15.212(a)(1) For Items Marked “NO(*)”, the Limited Module Description Must be Filled Out on the Following Pages Modular Approval Requirement Requirement Met 1. The modular transmitter must have its own RF shielding. This is intended to ensure that the module does not have to rely upon the shielding provided by the device into which it is installed in order for all modular transmitter emissions to comply with FCC limits. It is also intended to prevent coupling between the RF circuitry of the module and any wires or circuits in the device into which the module is installed. Such coupling may result in non-compliant operation. The physical crystal and tuning capacitors may be located external to the shielded radio elements. 15.212(a)(1)(i) ☒ - YES ☐ - NO(*) Details: The module contains a metal shield which covers all RF components and circuitry. The shield is located on the top of the board. 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with FCC requirements under conditions of excessive data rates or over-modulation. 15.212(a)(1)(ii) ☒ - YES ☐ - NO(*) Details: External data inputs are buffered and processed by the internal digital circuitry before being applied to the RF modulation circuitry. The external data interfaces do not directly control the RF modulation parameters. Therefore, excessive input data rates cannot cause over-modulation or operation outside the authorized RF parameters. 3. The modular transmitter must have its own power supply regulation on the module. This is intended to ensure that the module will comply with FCC requirements regardless of the design of the power supplying circuitry in the device into which the module is installed. 15.212(a)(1)(iii) ☒ - YES ☐ - NO(*) Details: The module contains its own power supply regulation. Please refer to schematic file with this application. 4. The modular transmitter must comply with the antenna and transmission system requirements of §§ 15.203, 15.204(b), 15.204(c), 15.212(a), and 2.929(b). The antenna must either be permanently attached or employ a ‘‘unique’’ antenna coupler (at all connections between the module and the antenna, including the cable). The ‘‘professional installation’’ provision of § 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph 15.212(b). 15.212(a)(1)(iv) ☒ - YES ☐ - NO(*) Details: The module incorporates a permanently integrated PCB pattern antenna. The antenna is not user-replaceable, and no external antenna connector is provided. 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified or commercially available (see Section 15.31(i)). 15.212(a)(1)(v) ☒ - YES ☐ - NO(*) Details: The module is tested in an independent configuration (using a test fixture) and not in another device during testing. Uniqconn Inc. 070920-02b Modular Approval Requirement Requirement Met 6. The modular transmitter must be labeled with its own FCC ID number, or use an electron display (see KDB Publication 784748). If using a permanently affixed label with its own FCC ID number, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC certified transmitter module(s).” Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. 15.212(a)(1)(vi) ☒ - YES ☐ - NO(*) Details: There is a label on the module as shown in the labeling exhibit filed with this application. 7. The modular transmitter must comply with all sp…

Text truncated - open the document above for the full version.

Uniqconn Inc. Short Term Confidentiality Request Letter Federal Communications Commission Authorization and Evaluation Division FCC ID: 2BWYH-UC60M62-RX Pursuant to sections 0.457 and 0.459 of CFR 47 Commission’s policy and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 180 days: 1. External Photos 2. Internal Photos 3. Test Setup Photos 4. User Manual The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, _________________ Name: KWANGIL CHOI Position: Hardware Engineer Date: 2026-07-23

Uniqconn Inc. Confidentiality Request Letter Federal Communications Commission Authorization and Evaluation Division FCC ID: 2BWYH-UC60M62-RX Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: 1. Block Diagram 2. Schematics 3. Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, _________________ Name: KWANGIL CHOI Position: Hardware Engineer Date: 2026-07-23

Uniqconn Inc. Declaration of Authorization We Name: Uniqconn Inc. Address: 42, Changeop-ro, Sujeong-gu, Seongnam-si, Gyeonggi-do, South Korea Declare that: Name Representative of agent: Marlin Chen Agent Company name: MRT Technology (Suzhou) Co., Ltd. Address: D8 Building, Youxin Industrial Park, No.2 Tian'edang Rd., Wuzhong Economic Development Zone City: Suzhou Country: China is authorized to apply for Certification of the following product(s): Product: 60 GHz Full-Duplex Wireless Communication Module FCC ID: 2BWYH-UC60M62-RX Model: UC60M62-RX Sincerely, _________________ Name: KWANGIL CHOI Position: Hardware Engineer Date: 2026-07-23

Label & Label Location Bottom Side SilkScreen

MRT Technology (Suzhou) Co., Ltd. Report No.: R26S1011078-U401 Phone: +86-512-66308358 Report Version: V02 Web: www.mrt-cert.com Issue Date: 2026-08-11 Template Version: 3.0 1 of 10 RF Exposure Evaluation Declaration FCC ID: 2BWYH-UC60M62-RX Applicant: Uniqconn Inc. Product: 60 GHz Full-Duplex Wireless Communication Module Model No.: UC60M62-RX Brand Name: UNIQCONN FCC Rule Part(s): FCC Part 2.1091 KDB 447498 D04 v01 Result: Complies Evaluation Date: 2026-07-27 Prepared By: Aurora Ding Reviewed By: Denise Zhou Approved By: Robin Wu The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report. Testing was performed in accordance with the applicable measurement procedures. The test results reported herein apply only to the specific item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. Report No.: R26S1011078-U401 2 of 10 Revision History Report No. Version Description Issue Date Note R26S1011078-U401 V01 Initial Report 2026-08-04 Invalid R26S1011078-U401 V02 Updated FCC Rule Part(s) 2026-08-11 Valid Report No.: R26S1011078-U401 3 of 10 CONTENTS Description Page 1. General Information ............................................................................................................................... 4 1.1. Applicant ........................................................................................................................................4 1.2. Manufacturer .................................................................................................................................4 1.3. Testing Facility ...............................................................................................................................4 1.4. Product Information .......................................................................................................................5 1.5. Antenna Details .............................................................................................................................5 1.6. Device Classification .....................................................................................................................5 1.7. Applied Standards .........................................................................................................................5 2. RF Exposure Evaluation ........................................................................................................................ 6 2.1. Limits .............................................................................................................................................6 2.2. MPE Exemptions ...........................................................................................................................7 2.3. Calculated Result ....................................................................................................................... 10 Report No.: R26S1011078-U401 4 of 10 1. General Information 1.1. Applicant Uniqconn Inc. 42, Changeop-ro, Sujeong-gu, Seongnam-si, Gyeonggi-do, Republic of Korea 1.2. Manufacturer Uniqconn Inc. 42, Changeop-ro, Sujeong-gu, Seongnam-si, Gyeonggi-do, Republic of Korea 1.3. Testing Facility Test Site - MRT Suzhou Laboratory Laboratory Location (Suzhou - Wuzhong) D8 Building, No.2 Tian’edang Rd., Wuzhong Economic Development Zone, Suzhou, China Laboratory Location (Suzhou - SIP) 4b Building, Liando U Valley, No.200 Xingpu Rd., Shengpu Town, Suzhou Industrial Park, China Laboratory Location (Suzhou - Wujiang) Building 1, No.1 Xingdong Road, Wujiang, Suzhou, Jiangsu, People’s Republic of China Laboratory Accreditations A2LA: 3628.01 CNAS: L10551 FCC: CN1166 ISED: CN0001 Test Site - MRT Shenzhen Laboratory Laboratory Location (Shenzhen) 1G, Building A, Junxiangda Building, Zhongshanyuan Road West, Nanshan District, Shenzhen, China Laboratory Accreditations A2LA: 3628.02 FCC: CN1284 ISED: CN0105 Report No.: R26S1011078-U401 5 of 10 1.4. Product Information 1.5. Antenna Details Frequency Range 57 ~ 64 GHz Antenna Type PCB Antenna Max. Antenna Gain 7.5 dBi Note: The antenna gain is from antenna data sheet provided by the manufacturer. 1.6. Device Classification According to the user manual, this device is classified as a Mobile Device. So, the RF exposure evaluation requirements of § 2.1091 for mobile device exposure conditions subject to MPE limits. 1.7. Applied Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards: ⚫ FCC Part 2.1091 ⚫ KDB 447498 D04 Interim General RF Exposure Guidance v01 Product Name 60 GHz Full-Duplex Wireless Communication Module Model No. UC60M62-RX Hardware Version V1.0 Wireless Specification 57 ~ 64 GHz Operating Temperature -40 ~ 85 °C Product Voltage 3.3 VDC Note: The information of the EUT (Equipment Under Test) was provided by the manufacturer. The accuracy, completeness, and validity of the information are solely the responsibility of the manufacturer. Report No.: R26S1011078-U401 6 of 10 2. RF Exposure Evaluation 2.1. Limits According to FCC §1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in §1.1307(b) Limits For Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (Minutes) (A) Limits for Occupational/ Control Exposures 0.3 ~ 3.0 614 1.63 *(100) ≤6 3.0 ~ 30 1842/f 4.89/f *(900/f 2 ) <6 30 ~ 300 61.4 0.163 1.0 <6 300 ~ 1500 -- -- f/300 <6 1500 ~ 100000 -- -- 5 <6 (B) Limits for General Population/ Uncontrolled Exposures 0.3 ~ 1.34 614 1.63 *(100) <30 1.34 ~ 30 824/f 2.19/f *(180/f 2 ) <30 30 ~ 300 27.5 0.073 0.2 <30 300 ~ 1500 -- -- f/1500 <30 1500 ~ 100000 --…

Text truncated - open the document above for the full version.

Wirelesshigh-speeddatatransfersolution, replacingcableand connector Antenna Specification 1 Antenna Manufacturer •Name : Uniqconn Inc. •Address : 42, Changeop-ro, Sujeong-gu, Seongnam-si, Gyeonggi-do, Republic of Korea p. 2 Linear Dual-polarization Antenna ⚫Dual-polarization (V-pol & H-pol) ⚫2 Array Antenna (Broad-side Beam) ⚫Low-Cost[4 layer] & Compact Size & Patch Antenna [PCB Type] Type No.UC60ABSD8V0 Frequency range57 - 64 GHz VSWR<1.5 (R/L >14) Gain7.5 dBi Half-power beam- width Hor.60° Ver.40° Isolation, between ports> 30dB Input Impedance50Ω PolarizationV/H Antenna size (Height x width x depth) 6.9 x 7.2 x 0.6mm Horizontal Vertical ⚫RadiationPattern

MRT Technology (Suzhou) Co., Ltd. Report No.: R26S1011078-U201 Phone: +86-512-66308358 Report Version: V03 Web: www.mrt-cert.com Issue Date: 2026-08-12 Template Version: 3.0 1 of 45 FCC ID: 2BWYH-UC60M62-RX Applicant: Uniqconn Inc. Product: 60 GHz Full-Duplex Wireless Communication Module Model No.: UC60M62-RX Brand Name: UNIQCONN FCC Classification: Part 15 Low Power Communication Device Transmitter (DXX) FCC Rule Part(s): FCC PART 15.255 Received Date: 2026-07-08 Test Date: 2026-07-21 ~ 2026-07-31 Prepared By: Aurora Ding Reviewed By: Denise Zhou Approved By: Robin Wu RF MEASUREMENT REPORT The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report. Testing was performed in accordance with the applicable measurement procedures. The test results reported herein apply only to the specific item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. Report No.: R26S1011078-U201 2 of 45 Revision History Report No. Version Description Issue Date Note R26S1011078-U201 V01 Initial Report 2026-08-05 Invalid R26S1011078-U201 V02 Updated Section 6.4.5 2026-08-11 Invalid R26S1011078-U201 V03 Updated Section 1.5 2026-08-12 Valid Report No.: R26S1011078-U201 3 of 45 CONTENTS Description Page 1. General Information ..................................................................................................................................... 5 1.1. Applicant ........................................................................................................................................... 5 1.2. Manufacturer .................................................................................................................................... 5 1.3. Testing Facility .................................................................................................................................. 5 1.4. Product information .......................................................................................................................... 6 1.5. Radio Specification .......................................................................................................................... 6 2. Test Configuration ........................................................................................................................................ 7 2.1. Test Mode ......................................................................................................................................... 7 2.2. Test System Connection Diagram .................................................................................................... 7 2.3. Applied Standards ............................................................................................................................ 8 2.4. Test Environment Condition ............................................................................................................. 8 3. Antenna Requirements ................................................................................................................................ 9 4. Measuring Instrument ................................................................................................................................ 10 5. Decision Rules and Measurement Uncertainty .......................................................................................... 12 5.1. Decision Rules ............................................................................................................................... 12 5.2. Measurement Uncertainty .............................................................................................................. 12 6. Test Result.................................................................................................................................................. 13 6.1. Summary ........................................................................................................................................ 13 6.2. Emission Bandwidth ....................................................................................................................... 14 6.2.1. Test Limit ........................................................................................................................................ 14 6.2.2. Test Procedure ............................................................................................................................... 14 6.2.3. Test Setting ..................................................................................................................................... 14 6.2.4. Test Setup ...................................................................................................................................... 15 6.2.5. Test Result ...................................................................................................................................... 16 6.3. Peak EIRP & Output Power ........................................................................................................... 18 6.3.1. Test Limit ........................................................................................................................................ 18 6.3.2. Test Procedure ............................................................................................................................... 18 6.3.3. Test Setting ..................................................................................................................................... 19 6.3.4. Test Setup ...................................................................................................................................... 20 6.3.5. Test Result ...................................................................................................................................... 21 6.4. Trans…

Text truncated - open the document above for the full version.