2BXFY-K700Karaoke Machine

PORTABLE KARAOKE MACHINE OWNER'S MANUAL UWJ Model: K700 OWNER'S MANUAL ISM BlueTooth 2.4GHz ISM BlueTooth 2.4GHz 1 TABLE OF CONTENTS 1.INTRODUCTION 2.WHAT'S IN THE BOX 3.PRODUCT OVERVIEW 4.PLACEMENT 5.POWER ON 6.USING YOUR KARAOKE MACHINE 7. CARRYING YOUR KARAOKE MACHINE 8. COMPLIANCE 9. IMPORTANT SAFETY & CARE NOTES 10.TROUBLESHOOTING 11.FCC Statement 12.IMPORTANT SAFETY INSTRUCTIONS – BATTERY WARNING 3.1 TOP PANEL 3.2 WIRELESS MICROPHONE 6.1 BLUETOOTH CONNECTION 6.2 USB CONNECTION 6.3 TF CARD CONNECTION 6.4 AUX CONNECTION 6.5 MUSIC CONTROLS 6.6 WIRELESS MICROPHONE 6.7 MIC PRIORITY / MUSIC ONLY MODE 6.8 TWS MODE 6.9 LED LIGHT EFFECTS 6.10 WIRED MICROPHONE, INSTRUMENT & SOUND MIXING 2 1. INTRODUCTION Congratulations on your purchase! This manual includes information about the Portable Karaoke Machine. Please take a few minutes to read this manual before use. It includes product information, setup instructions, operating guidance, Read and understand all safety instructions before using this product.If you have any questions about this product, setup, or operation, please contact our customer service team. 2. WHAT'S IN THE BOX 3. PRODUCT OVERVIEW 3.1 Top Panel Power Button Press this button to turn the karaoke machine on or off. Once the wireless microphone is powered on, it will automatically pair with the karaoke machine with voice prompts. AUX Input Connect an external audio device via an AUX cable, then press the Mode button to switch to AUX mode. Insert a TF card and press the Mode button to select TF mode and play MP3 files. TF Card Slot Insert a USB flash drive and press the Mode button to select USB mode and play MP3 files. USB Port Mic Priority / Music Mode Button Short-press to enable or disable Music-Only Mode. Long-press to enable or disable Mic Priority Mode. LED Button Short press to cycle through 6 lighting modes. LED lights flash in sync with music beats. Mode Button The karaoke machine enters Bluetooth mode by default when powered on, and “BLUE” flashes on the display. Short press the Mode button to switch between available input modes: Bluetooth, AUX, TF, and USB. Previous Track Button Short press to play the previous track. Press and hold to rewind. Play / Pause Button Short press to play or pause music. The LED display shows “PAUS”LED display when music is paused. In Bluetooth mode, press and hold to disconnect the Bluetooth connection. Next Track Button Short press to play the next track. Press and hold to fast forward. DC 5V Charging Port Charge the karaoke machine with the supplied USB-C charging cable or another standard USB-C cable. Power adapter is not included. 1 Main Unit ×1 Wireless Microphone ×2 USB-C Charging Cable ×1 Shoulder Strap ×1 User Manual ×1 1 2 3 4 5 45 23 1 101213141511 2 35 16 674 8 7 8 9 10 11 9 1 2 3 4 5 6 BLUE 3 3.2 Wireless Microphone LED display Turn clockwise to increase master volume. Turn counterclockwise to decrease master volume. The display shows the master volume level from U00 to U32. Master Volume Knob Rotate to adjust the microphone echo level. The display shows the echo level from Mic Echo Knob Rotate to adjust the microphone volume. The display shows the microphone volume level from Mic Volume Knob For connecting a wired microphone or musical instruments such as guitar. MIC / Instrument Jack Shows playback mode, elapsed play time, battery level, master volume, mic volume, and echo level. LED Display Screen Flashes while waiting to connect. Stays solid once the wireless microphone successfully connects to the karaoke machine. Connection Indicator Light Press and hold to turn the wireless microphone on or off. Wireless Mic Power Button 4. PLACEMENT 5. POWER ON Caution: Do not sit on the karaoke machine, press it with force, or place heavy objects on it. Otherwise, it may cause malfunction, personal injury, or property damage. Place the karaoke machine on a flat, stable surface and make sure the rubber feet side is facing down. 12 13 14 15 16 2 1 Caution: Use a standard 5V USB adapter to charge the karaoke machine. Recommended adapter output: 5V/1A or higher current,such as 5V/2A. Do not use fast chargers or adapters with output voltage higher than 5V. Adapters with output lower than 5V/1A are not recommended, as charging may be slow or unstable. The karaoke machine can be used while charging. Use the supplied USB-C cable or another standard USB-C cable. Fully charge the karaoke machine before first-time use to help protect the built-in battery. To protect battery life, fully charge the karaoke machine at least once every 3 months when not in use for a long time. Battery life will vary depending on usage patterns and environmental conditions. Press to power on or off. Tips: 2 1 E-00 to E-16. N-00 to N-16. Low Battery Sufficient Battery Low Battery Flash BLUE 4 6.1 Bluetooth Connection 6. USING YOUR KARAOKE MACHINE Notes: Only one audio source can be played at a time. The karaoke machine starts in Bluetooth mode by default. Other modes will not be displayed or selected if a T F card, USB flash drive, is not connected. Press the Mode button to switch between available modes. For better Bluetooth performance, keep your Bluetooth device within the effective connection range of the karaoke machine and avoid walls or strong wireless interference. When powered on, the karaoke machine enters Bluetooth mode by default, and “BLUE” flashes on the LED display. Turn on Bluetooth on your device and search for “K700 KARAOKE MACHINE”. Select “K700 KARAOKE MACHINE” to complete the connection. Once connected successfully, the display stops flashing and a voice prompt will sound. You can now play music from your Bluetooth device. The karaoke machine will automatically reconnect to the last paired device after powering on again. If the connection fails, turn Bluetooth off and back on your device, then reconnect. Bluetooth performance may be affected by distance, walls, or nearby wireless devices. You can connect the karaoke machine to Bluetooth- enable…

Text truncated - open the document above for the full version.

ReferenceNo.2026UL0268 2.911(d)(7)USAAgentv1.3 Section2.911(d)(7)USAAgentforServiceofProcess Companyname:GuangdongLiwanIntelligentElectricalApplianceCo.,Ltd. ProductDescription:KaraokeMachine FCCID:2BXFY-K700 ContactName:LaiZongren Address:Room101,No.1DongyeRoad,HoujieTown,DongguanCity,Guangdong Province,P.R.China TelephoneNo:+86-15876462217 Email:[email protected] 2.911(d)(7)USADesignatedAgentforServiceofProcess We,[GuangdongLiwanIntelligentElectricalApplianceCo.,Ltd.](“theapplicant”) designate[TTSMARKETINC.] NOTE1 forthepurposeofacceptingserviceofprocess onbehalfoftheapplicant. Applicantconsent:WeAcknowledgeourconsenttoacceptserviceofprocessinthe UnitedStatesformattersrelatedtotheapplicableequipment,andatthephysicalU.S. addressandemailaddressofthedesignatedagentandacknowledgeour acceptanceofourobligationtomaintainanagentforserviceofprocessintheUnited Statesfornolessthanoneyearaftereitherthegranteehaspermanentlyterminated allmarketingandimportationoftheapplicableequipmentwithintheU.S.,orthe conclusionofanyCommission-relatedadministrativeorjudicialproceedinginvolving theequipment,whicheverislater. Agentobligation:WeAcknowledgeourobligationtoacceptserviceofprocessinthe UnitedStatesformattersrelatedtotheapplicableequipmentatourphysicalU.S. addressandemailaddressfornolessthanoneyearaftereitherthegranteehas permanentlyterminatedallmarketingandimportationoftheapplicableequipment withintheU.S.,ortheconclusionofanyCommission-relatedadministrativeorjudicial proceedinginvolvingtheequipment,whicheverislater. USAAgent Companyname:TTSMARKETINC. Address:1178BroadwaySte324,New York,NY10001,USA FRN:0036806057 ContactName:MaverickLim Applicant Companyname:GuangdongLiwan IntelligentElectricalApplianceCo.,Ltd. Address:Room101,No.1DongyeRoad, HoujieTown,DongguanCity,Guangdong Province,P.R.China FCCGranteeCode:2BXFY FRN:0038716106 ContactName:LaiZongren ReferenceNo.2026UL0268 2.911(d)(7)USAAgentv1.3 TelephoneNo:(646)305-2908 Email:[email protected] TelephoneNo:+86-15876462217 Email:[email protected] Signature: Title:Manager Signature: Title:factorydirector Date:2026.9.3Date:2026.9.3 NOTE1:AnapplicantlocatedintheUnitedStatesmaydesignateitselfastheagentfor serviceofprocess. Reference;FederalRegisterdocument2022-28263publishedon02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against- national-security-threats-to-the-communications-supply-chain-through-the

Guangdong Liwan Intelligent Electrical Appliance Co., Ltd. Date: 8/12/2026 Federal Communications Commissions Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: CFR 47 §2.911 (d)(7) Agent Designation Attestation FCC ID: 2BXFY-K700 Grantee FRN: 0038716106 Guangdong Liwan Intelligent Electrical Appliance Co., Ltd. as required by section 2.911(d)(7), designates the following agent, located in the United States, for purposes of acting as the applicant’s agent for service of process. The applicant acknowledges that they will maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility under CFR 47 §2.929(c) to inform the FCC whenever the agent information changes. U.S. Agent Information: Contact Person: Maverick Lim Company Name: TTS MARKET INC. Company Address: 1178 Broadway Ste 324, New York, NY 10001, United States FCC FRN: 0036806057 Email: [email protected] Sincerely yours, Name: Zongren Lai Job Title: factory director Company Name: Guangdong Liwan Intelligent Electrical Appliance Co., Ltd.

External Photographs Page 2 of 4 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. External Page 3 of 4 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Page 4 of 4 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch.

label location Note: This label will be permanently paste on the product

Internal Photographs Page 2 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal Page 3 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Page 4 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. PCB Antenna Page 5 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Page 6 of 6 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch.

FCC ID: 2BXFY-K700 According to 447498 D04 Interim General RF Exposure Guidance v01, 2.1.4 MPE-Based Exemption An alternative to the SAR-based exemption is provided in § 1.1307(b)(3)(i)(C), for a much wider frequency range, from 300 kHz to 100 GHz, applicable for separation distances greater or equal to λ/2π, where λ is the free-space operating wavelength in meters. The MPE-based test exemption condition is in terms of ERP, defined as the product of the maximum antenna gain and the delivered maximum time-averaged power.10 For this case, a RF source is an RF exempt device if its ERP (watts) is no more than a frequency-dependent value, as detailed tabular form in Appendix B. These limits have been derived based on the basic specifications on Maximum Permissible Exposure (MPE) considered for the FCC rules in § 1.1310(e)(1). B.4 SAR-based Exemption SAR-based thresholds are derived based on frequency, power, and separation distance of the RF source. The formula defines the thresholds in general for either available maximum time- averaged power or maximum time-averaged ERP, whichever is greater. If the ERP of a device is not easily determined, such as for a portable device with a small form factor, the applicant may use the available maximum time-averaged power exclusively if the device antenna or radiating structure does not exceed an electrical length of λ/4. As for devices with antennas of length greater than λ/4 where the gain is not well defined, but always less than that of a half-wave dipole (length λ/2), the available maximum time-averaged power generated by the device may be used in place of the maximum time-averaged ERP, where that value is not known. The separation distance is the smallest distance from any part of the antenna or radiating structure for all persons, during operation at the applicable ERP. In the case of mobile or portable devices, the separation distance is from the outer housing of the device where it is closest to the antenna. The SAR-based exemption formula of § 1.1307(b)(3)(i)(B), repeated here as Formula (B.2), applies for single fixed, mobile, and portable RF sources with available maximum time-averaged power or effective radiated power (ERP), whichever is greater, of less than or equal to the threshold Pth (mW). This method shall only be used at separation distances from 0.5 cm to 40 cm and at frequencies from 0.3 GHz to 6 GHz (inclusive). Pth is given by Formula (B.2). and f is in GHz, d is the separation distance (cm), and ERP 20cm is per Formula (B.1). The example values shown in Table B.2 are for illustration only. 1. Conclusion Test Mode Max Tune- up Power [dBm] Max Tune- up Power [mW] Antenna Gain [dBi] EIRP [dBm] ERP [dBm] ERP [mW] Limit [mW] Conclusion BT -4.00 0.40 0.26 -3.74 -5.89 0.26 3.00 No SAR is required. Note: 1. When the minimum test separation distance is 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2. Tune-up power comes from operation description.

The results reported herein have been performed in accordance with the laboratory’s terms of accreditation. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report apply to the test sample(s) mentioned above at the time of the testing period only and are not to be used to indicate applicability to other similar products. FCC 47 CFR PART 15 SUBPART C TEST REPORT For Karaoke Machine MODEL NUMBER: K700 REPORT NUMBER: 4792341462-3-RF-1 ISSUE DATE: August 17, 2026 FCC ID: 2BXFY-K700 Prepared for Guangdong Liwan Intelligent Electrical Appliance Co., Ltd. Room 101, No.1 Dongye Road, Houjie Town, Dongguan City, Guangdong Province, P.R.China Prepared by UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch Room 101, Building 2, No.4, Information Road, Songshan Lake, Dongguan, Guangdong, China Tel: +86 769 22038881 Fax: +86 769 33244054 Website: www.ul.com REPORT NO.: 4792341462-3-RF-1 Page 2 of 94 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0035 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Revision History Rev. Issue Date Revisions Revised By V0 August 17, 2026 Initial Issue REPORT NO.: 4792341462-3-RF-1 Page 3 of 94 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0035 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Summary of Test Results Test Item Clause Limit/Requirement Result Antenna Requirement N/A FCC 15.203 Pass AC Power Line Conducted Emission ANSI C63.10-2020 Clause 6.2 FCC Part 15.207 Pass Conducted Output Power ANSI C63.10-2020 Clause 7.8.5 FCC 15.247 (b) (1) Pass 20 dB Bandwidth and 99% Occupied Bandwidth ANSI C63.10-2020 Clause 6.9.2 & 6.9.3 FCC 15.247 (a) (1) Pass Carrier Hopping Channel Separation ANSI C63.10-2020 Clause 7.8.2 FCC 15.247 (a) (1) Pass Number of Hopping Frequency ANSI C63.10-2020 Clause 7.8.3 15.247 (a) (1) III Pass Time of Occupancy (Dwell Time) ANSI C63.10-2020 Clause 7.8.4 15.247 (a) (1) III Pass Conducted Bandedge and Spurious Emission ANSI C63.10-2020 Clause 6.10.4 & Clause 7.8.7 FCC 15.247 (d) Pass Duty Cycle ANSI C63.10-2020, Clause 11.6 None; for reporting purposes only. Pass Radiated Band edge and Spurious Emission ANSI C63.10-2020 Clause 6.4 & 6.5 & 6.6 & 7.8.8 FCC 15.247 (d) FCC 15.209 FCC 15.205 Pass Note: 1. For FCC, this report is also performed according to ANSI C63.10-2020 + Cor.1-2023 + C63.10a-2024 + Errata to C63.10a-2024 standards. *This test report is only published to and used by the applicant, and it is not for evidence purpose in China. *The measurement result for the sample received is <Pass> according to <FCC 47 CFR PART 15 SUBPART C> when <Simple Acceptance> decision rule is applied. Decision rule for statement of conformity: The measurement uncertainty is not taken into account for statement of conformity. REPORT NO.: 4792341462-3-RF-1 Page 4 of 94 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0035 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. CONTENTS 1. ATTESTATION OF TEST RESULTS ..................................................................................... 6 2. TEST METHODOLOGY ......................................................................................................... 7 3. FACILITIES AND ACCREDITATION ..................................................................................... 7 4. CALIBRATION AND UNCERTAINTY ................................................................................... 8 4.1. MEASURING INSTRUMENT CALIBRATION ........................................................... 8 4.2. MEASUREMENT UNCERTAINTY ............................................................................ 8 5. EQUIPMENT UNDER TEST .................................................................................................. 9 5.1. DESCRIPTION OF EUT ........................................................................................... 9 5.2. CHANNEL LIST ........................................................................................................ 9 5.3. MAXIMUM POWER .................................................................................................. 9 5.4. TEST CHANNEL CONFIGURATION ...................................................................... 10 5.5. THE WORSE CASE POWER SETTING PARAMETER .......................................... 10 5.6. DESCRIPTION OF AVAILABLE ANTENNAS ......................................................... 11 5.7. SUPPORT UNITS FOR SYSTEM TEST ................................................................. 12 6. MEASURING EQUIPMENT AND SOFTWARE USED......................................................... 14 7. ANTENNA PORT TEST RESULTS ..................................................................................... 17 7.1. CONDUCTED OUTPUT POWER ........................................................................... 17 7.2. 20 DB BANDWIDTH AND 99% OCCUPIED BANDWIDTH ..................................... 18 7.3. CARRIER HOPPING CHANNEL SEPARATION ..................................................... 20 7.4. NUMBER OF HOPPING FREQUENCY .................................................................. 22 7.5. TIME OF OCCUPANCY (DWELL TIME) ................................................................. 24 7.6. CONDUCTED BANDEDGE AND SPURIOUS EMISSION ...................................... 26 7.7. DUTY CYCLE ......................................................................................................... 28 8. RADIATED TEST RESULTS ....................................................................................…

Text truncated - open the document above for the full version.

Report No.: Ti-EE26080478-901 Tel: +86-755-66850100 E-mail: [email protected] Page No. 1 / 14 Web: www.titcgroup.com Template No.: TRP-Passive-EN (2022-09-07) Add: 601, Building 2, Intelligent Connected Vehicle Industrial Park, No.55, Xiangshan Road, Luotian Community, Yanluo Sub-district, Bao'an District, Shenzhen TEST REPORT Applicant: Guangdong Liwan Intelligent Electrical Appliances Co., Ltd. Address: Room 101, No. 1, Dongye Road, Houjie Town, DONGGUAN CITY, Guangdong Province Equipment Type: Karaoke Machine Antenna Model Name: K700 Brand Name: N/A Test Standard: IEEE Std 149-2021 Sample Arrival Date: Aug. 17, 2026 Test Date: Aug. 17, 2026 Date of Issue: Aug. 25, 2026 ISSUED BY: Shenzhen BALUN Technology Co., Ltd. Tested by: Mai Jintian Checked by: Xia Long Approved by: Tolan Tu (Technical Director) _______________ _______________ _______________ Report No.: Ti-EE26080478-901 Tel: +86-755-66850100 E-mail: [email protected] Page No. 2 / 14 Web: www.titcgroup.com Template No.: TRP-Passive-EN (2022-09-07) Add: 601, Building 2, Intelligent Connected Vehicle Industrial Park, No.55, Xiangshan Road, Luotian Community, Yanluo Sub-district, Bao'an District, Shenzhen Revision History Version Issue Date Revisions Rev. 01 Aug. 25, 2026 Initial Issue TABLE OF CONTENTS 1 GENERAL INFORMATION ........................................................................................................ 3 1.1 Test Laboratory .................................................................................................................. 3 1.2 Test Location ...................................................................................................................... 3 2 PRODUCT INFORMATION ....................................................................................................... 4 2.1 Applicant Information .......................................................................................................... 4 2.2 Manufacturer Information .................................................................................................... 4 2.3 General Description for Equipment under Test (EUT) ......................................................... 4 2.4 Ancillary Equipment ............................................................................................................ 4 3 SUMMARY OF TEST RESULTS ............................................................................................... 5 3.1 Test Standards ................................................................................................................... 5 3.2 Test Verdict ........................................................................................................................ 5 3.3 Test Uncertainty ................................................................................................................. 5 4 GENERAL TEST CONFIGURATIONS ...................................................................................... 6 4.1 Test Condition .................................................................................................................... 6 4.2 Test Equipment List ............................................................................................................ 6 4.3 Test Setup .......................................................................................................................... 7 4.4 Test Frequencies ................................................................................................................ 7 ANNEX A TEST RESULTS .......................................................................................................... 8 A.1 Gain and Efficiency ............................................................................................................. 8 A.2 VSWR ................................................................................................................................. 9 ANNEX B RADIATION PATTERN ............................................................................................. 10 ANNEX C TEST SETUP PHOTOS ............................................................................................ 13 ANNEX D EUT PHOTO.............................................................................................................. 13 Report No.: Ti-EE26080478-901 Tel: +86-755-66850100 E-mail: [email protected] Page No. 3 / 14 Web: www.titcgroup.com Template No.: TRP-Passive-EN (2022-09-07) Add: 601, Building 2, Intelligent Connected Vehicle Industrial Park, No.55, Xiangshan Road, Luotian Community, Yanluo Sub-district, Bao'an District, Shenzhen 1 GENERAL INFORMATION 1.1 Test Laboratory Name Shenzhen BALUN Technology Co., Ltd. Address 601, Building 2, Intelligent Connected Vehicle Industrial Park, No.55, Xiangshan Road, Luotian Community, Yanluo Sub-district, Bao'an District, Shenzhen Phone Number +86 755 6685 0100 1.2 Test Location Name Shenzhen BALUN Technology Co., Ltd. Location 1/F., Building B, Ganghongji High-Tech Intelligent Industrial Park, No.1008, Songbai Road, Yangguang Community, Xili Subdistrict, Nanshan District, Shenzhen, Guangdong Building 2, Intelligent Connected Vehicle Industrial Park, No.55, Xiangshan Road, Luotian Community, Yanluo Sub-district, Bao'an District, Shenzhen, Guangdong Report No.: Ti-EE26080478-901 Tel: +86-755-66850100 E-mail: [email protected] Page No. 4 / 14 Web: www.titcgroup.com Template No.: TRP-Passive-EN (2022-09-07) Add: 601, Building 2, Intelligent Connected Vehicle Industrial Park, No.55, Xiangshan Road, Luotian Community, Yanluo Sub-district, Bao'an District, Shenzhen 2 PRODUCT INFORMATION 2.1 Applicant Information Applicant Guangdong Liwan Intelligent Electrical Appliances Co., Ltd. Address Room 101, No. 1, Dongye Road, Houjie Town, DONGGUAN CITY, Guangdong Province 2.2 Manufacturer Information Manufacturer Guangdong Liwan Intelligent Electrical Appliances Co., Ltd. Address Room 101, No. 1, Dongye Road, Houjie Town, DONGGUAN CITY, Guangdong Prov…

Text truncated - open the document above for the full version.

Appendix II Setup Photographs RADIATED RF MEASUREMENT SETUP (ABOVE 1 GHz) MEASUREMENT POSITION MEASUREMENT POSITION (X axis) MEASUREMENT POSITION (Y axis) MEASUREMENT POSITION (Z axis) RADIATED RF MEASUREMENT SETUP (30MHz~1GHz) RADIATED RF MEASUREMENT SETUP (Below 30MHz) AC CONDUCTED POWER LINE EMISSION

Report No.: Ti-EE26080478-AA 1 / 1 EUT PHOTO --BLANK BELOW-- PCB Antenna

Report No.: Ti-EE26080478-AO 1 / 1 TEST SETUP PHOTOS --BLANK BELOW--