2BXPI-TQ-1Remote control

FCC Warming: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. lf this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. RF warning for Portable device: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Local Representative Letter For Certification Service in the USA Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Section 2.911(d)(7), of the Commission’s Rules (47 C.F.R.) we attest as follows for the product listed below: FCC IDModel name 2BXPI-TQ-1TQ-1, TQ-2, TQ-3, TQ-4, TQ-5, TQ-6, TQ-7, TQ-8, TQ-9, TQ-10, TQ-11, TQ-12, TQ-13, TQ-14, TQ-15, TQ-16, TQ-20, TQ-21, TQ-22, TQ-23 We hereby acknowledge as follows: i.both signees confirm that the point of contact accepts responsibility to act as a US- American Representative on behalf of the applicant ii.the point of contact provides the physical U.S. address and email as listed below iii.both parties maintain the requirements of this agreement for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. iv.An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. US-American Point of ContactApplicant/Approval Holder Signature Date: 2026-08-14 Signature Date: 2026-08-14 Company Name:GLOCERTS TECHNOLOGY INCShantou Tianqu Toys Co., Ltd. FRN:00363397370038779740 Contact Name:Huiying FanChen Tong Address:19784 SUNKISSED RIDGE DR, RIVERSIDE, CA 92507 No. 8, Lane 11, District, Pumei Community, Guangyi Street, Chenghai Shantou City, Area 3rd Floor Phone:(626) 588-803915992265019 Email:[email protected]@qq.com

Shantou Tianqu Toys Co., Ltd. No. 8, Lane 11, District, Pumei Community, Guangyi Street, Chenghai Shantou City, Area 3rd Floor Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 Date: 2026-8-17 FCC ID: 22BXPI-TQ-1 Model Number: TQ-1, TQ-2, TQ-3, TQ-4, TQ-5, TQ-6, TQ-7, TQ-8, TQ-9, TQ-10, TQ-11, TQ-12, TQ-13, TQ-14, TQ-15, TQ-16, TQ-20, TQ-21, TQ-22, TQ-23 To Whom It May Concern, We, Shantou Tianqu Toys Co., Ltd. hereby declare that our product (as above) does not meet the definition of “Advanced robotic devices” as per FCC Public Notice DA-26-786A1 (Released: July 28, 2026), so is not within the FCC’s Covered List. More details as followed: The combined weight of the product unit and its charging docking station is 1.8012 lbs, equal to or less than 4.4 lbs, failing to satisfy the mandatory weight threshold for covered devices. Per definitions in Appendix C of DA-26-786, restricted advanced robotic devices must exceed 4.4 lbs in total combined weight. This product does not satisfy this mandatory criterion and is therefore not classified as a covered device. All movement and functional actions of this device require continuous real-time operator input. There is no pre-programmed route execution, autonomous obstacle avoidance, or capability to operate independently without human supervision. The product fails to meet the second foundational criterion requiring unsupervised autonomous operation and is excluded from Covered List coverage. Shantou Tianqu Toys Co., Ltd. No. 8, Lane 11, District, Pumei Community, Guangyi Street, Chenghai Shantou City, Area 3rd Floor Please do not hesitate to contact us for further explanations or comments. Sincerely, Name/Title： Chen Tong/Manager Company: Shantou Tianqu Toys Co., Ltd. Address: No. 8, Lane 11, District, Pumei Community, Guangyi Street, Chenghai Shantou City, Area 3rd Floor Phone: 15992265019 Fax: N/A E-Mail: [email protected]

Page 1 of 3 FCC ID: 2BXPI-TQ-1 External Photos Page 2 of 3 FCC ID: 2BXPI-TQ-1 Page 3 of 3 FCC ID: 2BXPI-TQ-1

Label FCC ID: 2BXPI-TQ-1

Page 1 of 2 FCC ID: 2BXPI-TQ-1 Internal Photos ANT Page 2 of 2 FCC ID: 2BXPI-TQ-1

Page 1 of 7 Report No.: AiTDG-260814010FW2 Note: This device has been tested and found to comply with the standard(s) listed, this test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. This report shall not be reproduced except in full, without the written approval of Dongguan Yaxu (AiT) Technology Limited. If there is a need to alter or revise this document, the right belongs to Dongguan Yaxu (AiT) Technology Limited, and it should give a prior written notice of the revision document. This test report must not be used by the client to claim product endorsement. Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China. RF Exposure evaluation Product Name:Remote control Brand Name: 金冠智 Model:TQ-1 Series Model: TQ-2, TQ-3, TQ-4, TQ-5, TQ-6, TQ-7, TQ-8, TQ-9, TQ-10, TQ-11, TQ-12, TQ-13, TQ-14, TQ-15, TQ-16, TQ-20, TQ-21, TQ-22, TQ-23 FCC ID:2BXPI-TQ-1 Applicant:Shantou Tianqu Toys Co., Ltd. Address: No. 8, Lane 11, District, Pumei Community, Guangyi Street, Chenghai Shantou City, Area 3rd Floor Manufacturer:Shantou Tianqu Toys Co., Ltd. Address: No. 8, Lane 11, District, Pumei Community, Guangyi Street, Chenghai Shantou City, Area 3rd Floor Standard(s): 47CFR §1.1310, 47CFR §2.1093 KDB447498 D01 General RF Exposure Guidance v06 Date of Receipt:May. 15, 2026 Date of Test:May. 15, 2026~ Aug. 05, 2026 Issued Date:Aug. 05, 2026 Issued By: Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China Tel.: +86-769-8202 0499 Fax.: +86-769-8202 0495 Reviewed by: Approved by: Emiya Lin Simba Huang Page 2 of 7 Report No.: AiTDG-260814010FW2 Report Revise Record Report VersionIssued DateNotes M0Aug. 05, 2026Initial Release Page 3 of 7 Report No.: AiTDG-260814010FW2 Contents 1GENERAL INFORMATION........................................................................................................................................4 1.1ENVIRONMENTAL CONDITIONS........................................................................................................................................4 1.2GENERAL DESCRIPTION OF EUT......................................................................................................................................4 1.3TEST FACILITY..............................................................................................................................................................5 1.4MEASUREMENT UNCERTAINTY........................................................................................................................................5 2METHOD OF MEASUREMENT..................................................................................................................................6 2.1APPLICABLE STANDARD.................................................................................................................................................6 2.2EVALUATION METHOD AND LIMIT...................................................................................................................................6 2.3MANUFACTURING TOLERANCE.......................................................................................................................................7 2.4EVALUATION RESULT....................................................................................................................................................7 2.5CONCLUSION...............................................................................................................................................................7 Page 4 of 7 Report No.: AiTDG-260814010FW2 1GENERAL INFORMATION 1.1Environmental conditions During the measurement the environmental conditions were within the listed ranges: Normal Temperature:25°C Relative Humidity:55 % Air Pressure:101 kPa 1.2General Description of EUT Product Name:Remote control Model/Type reference: TQ-1 Serial Model: TQ-2, TQ-3, TQ-4, TQ-5, TQ-6, TQ-7, TQ-8, TQ-9, TQ-10, TQ-11, TQ- 12, TQ-13, TQ-14, TQ-15, TQ-16, TQ-20, TQ-21, TQ-22, TQ-23 Model difference: All the models are electrically identical with the same mechanical structure and design except the model names. Power Rating:DC:4.5V Hardware Version: N/A Software Version:N/A Sample(s) Status: AiTDG-260814010-1(Normal sample) AiTDG-260814010-2(Engineer sample) SRD: Supported type: Wireless 2.4G Modulation: GFSK Operation frequency: 2420MHz~2460MHz Channel number: 3 Antenna type: Line antenna Antenna gain: 0.17dBi Remark: The above DUT's information was declared by manufacturer. For more detailed features description, please refer to the manufacturer’s specifications or the User's Manual.. Page 5 of 7 Report No.: AiTDG-260814010FW2 1.3Test Facility Test Laboratory: Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China The test facility is recognized, certified or accredited by the following organizations: CNAS-Registration No: L6177 Dongguan Yaxu (AiT) technology Limited is accredited to ISO/IEC 17025:2017 general Requirements for the competence of testing and calibration laboratories (CNAS-CL01 Accreditation Criteria for the competence of testing and calibration laboratories) on April 18, 2022 FCC-Registration No.: 703111 Designation Number: CN1313 Dongguan Yaxu (AiT) Technology Limited has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. IC-Registration No.: 6819A CAB identifier: CN0122 The 3m Semi-anechoic chamber of Dongguan Yaxu (AiT) Technology Limited has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 6819A A2LA-Lab Cert. No.: 6317.01 Dongguan Yaxu (AiT) Technology Limited has been…

Text truncated - open the document above for the full version.

Xinpengda Electronic Accessories Factory, Jinping District, Shantou City The factory building located on the west side of Huaxing New Town, on the west陇 area of Chaoshan Road, Shantou City 天线规格承认书 Antenna Specification for Approval 客户名称 Customer Name： 产品名称： Product Name：2.4G天线 全长33mm黑色 客户型号： Product Name: 产品料号： Part NO.:C10-35-2.5 制 表： Write By： 日 期： Issued Date:2016-3-20 第 蹋ㄩ M A TERIA L 机瞄ㄩ C H ECK IN G 錨璃晤瘍ㄩ PA RT N O . 錨璃靡備ㄩ PA RT TITLE D A TE ㄩ 掀瞰ㄩ D RW IN G 秶芞ㄩ 等弇ㄩ SCA LE U N IT IN V ER. 唳棒ㄩ 鼎茼妀 靡ㄩ SU PPLIER CFM 趼 揭杅 載蜊囀 梓暮 ProductSpecification A.Electrical Characteristics Frequency 2400MHz ~2500MHz VSWR <3.0 Efficiency >30% Impedance 50 Ohm Polarization Line Gain 0.17DBi B.Material & Mechanical Characteristics Material of Radiator Cu Cable Type 1.0 19P 黑色 Connector Type : NO Dimension C.Environmental Operation Temperature - 30 °C ~ + 80 °C Storage Temperature - 30 °C ~ + 85 °C Test Equipment& Conditions 1．NetworkAnalyzers: Agilent8753D5071B 2．CommunicationsTest Set: AgilentE5515C 3．3D ChamberTest System Effiency&Gain Effiency&Gain 2.40 -2.17 2.4400.12 2.480.17 RadiationPattern:

Page 1 of 27 Report No.: AiTDG-260814010FW1 Note: This device has been tested and found to comply with the standard(s) listed, this test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. This report shall not be reproduced except in full, without the written approval of Dongguan Yaxu (AiT) Technology Limited. If there is a need to alter or revise this document, the right belongs to Dongguan Yaxu (AiT) Technology Limited, and it should give a prior written notice of the revision document. This test report must not be used by the client to claim product endorsement. Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China. TEST REPORT Product Name:Remote control Brand Name: 金冠智 Model:TQ-1 Series Model: TQ-2, TQ-3, TQ-4, TQ-5, TQ-6, TQ-7, TQ-8, TQ-9, TQ-10, TQ-11, TQ-12, TQ-13, TQ-14, TQ-15, TQ-16, TQ-20, TQ-21, TQ-22, TQ-23 FCC ID:2BXPI-TQ-1 Applicant:Shantou Tianqu Toys Co., Ltd. Address: No. 8, Lane 11, District, Pumei Community, Guangyi Street, Chenghai Shantou City, Area 3rd Floor Manufacturer:Shantou Tianqu Toys Co., Ltd. Address: No. 8, Lane 11, District, Pumei Community, Guangyi Street, Chenghai Shantou City, Area 3rd Floor Standard(s):FCC CFR Title 47 Part 15 Subpart C Section 15.249 Date of Receipt:May. 15, 2026 Date of Test:May. 15, 2026~ Aug. 05, 2026 Issued Date:Aug. 05, 2026 Issued By: Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China Tel.: +86-769-8202 0499 Fax.: +86-769-8202 0495 Reviewed by: Approved by: Emiya Lin Simba Huang Page 2 of 27 Report No.: AiTDG-260814010FW1 Report Revise Record Report VersionIssued DateNotes M0Aug. 05, 2026Initial Release Page 3 of 27 Report No.: AiTDG-260814010FW1 Contents 1TEST SUMMARY......................................................................................................................................................4 1.1TEST STANDARDS.........................................................................................................................................................4 1.2TEST SUMMARY...........................................................................................................................................................4 1.3TEST FACILITY..............................................................................................................................................................5 1.4MEASUREMENT UNCERTAINTY........................................................................................................................................5 2GENERAL INFORMATION........................................................................................................................................6 2.1ENVIRONMENTAL CONDITIONS........................................................................................................................................6 2.2GENERAL DESCRIPTION OF EUT......................................................................................................................................6 2.3DESCRIPTION OF TEST MODES AND TEST FREQUENCY.........................................................................................................7 2.4EQUIPMENT LIST FOR THE TEST.......................................................................................................................................7 2.5EQUIPMENT LIST FOR THE TEST.......................................................................................................................................8 3TEST CONDITIONS AND RESULTS...........................................................................................................................10 3.1CONDUCTED EMISSIONS TEST.......................................................................................................................................10 3.2RADIATED EMISSIONS AND BAND EDGE..........................................................................................................................12 3.320DB BANDWIDTH....................................................................................................................................................19 3.4ANTENNA REQUIREMENT.............................................................................................................................................21 4TEST SETUP PHOTOGRAPHS OF EUT......................................................................................................................22 5PHOTOS OF EUT....................................................................................................................................................23 Page 4 of 27 Report No.: AiTDG-260814010FW1 1TEST SUMMARY 1.1Test Standards The tests were performed according to following standards: FCC Rules Part 15.249: Operation within the bands 902 - 928 MHz, 2400 - 2483.5 MHz, 5725 - 5875 MHz, and 24.0 -24.25 GHz. ANSI C63.10: 2020: American National Standard for Testing Unlicensed Wireless Devices 1.2Test Summary FCC PART 15.249 FCC Part 15.249(a)Field Strength of FundamentalPASS FCC Part 15.209Spurious EmissionPASS FCC Part 15.215(c)20dB bandwidthPASS FCC Part 15.207Conducted EmissionN/A FCC Part 15.203Antenna RequirementPASS Remark: 1. “N/A” denotes test is not applicable in this Test Report. Page 5 of 27 Report No.: AiTDG-260814010FW1 1.3Test Facility Test Laboratory: Dongguan Yaxu (AiT) Technology Limited No.22, Jinqianling 3rd Street, Jitigang, Huangjiang, Dongguan, Guangdong, China The test facility is recognized, certified or accredited by the following organizations: CNAS-Registration No: L6177 Dongguan Yaxu (AiT) technology Limited is accredited to ISO/IEC 17025:2017 general Requirements for the competence of testing and calibration laboratories (CNAS-CL01 Accreditation Criteria for the compe…

Text truncated - open the document above for the full version.

Page 1 of 1 FCC ID: 2BXPI-TQ-1