2BXPZ-S01selfie stick

FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement. Anleitung zur Fernbedienung 1.Drucken Sie zum Einschalten lange auf die Fernbedienungstaste. Die LED-Anzeige blinkt. 2.Suchen und koppeln Sie den wireless-Nam�n auf lhrem Mobiltelefon Nach erfolgreicher Verbindung hart die LED-Anzeige auf zu blinken. Verwenden Sie die Fernbedienung, um Bilder aufzunehmen, die LED blinktjeweils einmal 3.Die Fernbedienung schaltet sich nach 5 Minuten automatisch ab, wenn sie nicht gekoppelt ist 4.Die Fernbedienung schaltet nach 10 Minuten automatisch in den Ruhezustand Betrieb. und schaltet sich nach weiteren 10 Minuten automatisch ab, wenn man nicht aufwacht 5.Drucken Sie lange auf die Fernbedie_nungstaste, um das Gerat auszuschalten. Die LED-Anzeige blinkt 3 mal dann abgeschaltet Produktparameter Halterung Erweiterte Lange Erinnerung: 2.9-4.5 11 690-1700 mm Das kabellose Self ie-Stick-Stativ nutzt die Fernbedienung zum Aufnehmen von Fotos, anstatt auf die Kamera-App lhres Mobiltelefons zu klicken. Kompatibel mit Android-und iOS-Smartphones. (Nur fur Android-Telefone: Stellen Sie lhre Lautstarketastenfunktion als Aufnahme in der Kamera-App-Einstellung ein, darn it der Selfie-Stick ordnungsgemafs funktioniert.) Wenn Sie sich uber die genauen Schritte nicht im Klaren si nd, lesen Sie bitte eine andere detaillierte Bedienungsanleitung oder die Mall-Detailseite.

(Shenzhenjunyuelinghangkeji Co., Ltd.) (August 25, 2026) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for (FCC ID: 2BXPZ-S01) [Shenzhenjunyuelinghangkeji Co., Ltd.] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, the equipment does not utilize cyber-security or anti-virus software from Kaspersky Lab, Inc, or any of its successors and assignees, which is also on the “covered list”. Sincerely, () (Qiao Peng) (Shenzhenjunyuelinghangkeji Co., Ltd.) (August 25, 2026) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for (FCC ID: 2BXPZ-S01) [Shenzhenjunyuelinghangkeji Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, () (Qiao Peng)

Shenzhenjunyuelinghangkeji Co., Ltd. Building 3, Unit 2022, Phase II, Sunshine Yuehai Garden, No. 3818 Baishi Road Yuegui Community, Yuehai Subdistrict, Nanshan District, Shenzhen Guangdong, China Date: September 8, 2026 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BXPZ-S01 FRN: 0038789244 US Agent – Attestation Statement / Part 2.911(d)(7) Shenzhenjunyuelinghangkeji Co., Ltd.certifies, that as of September 8, 2026, we have designated FCC US Agent, LLC to accept service of process on our behalf for FCC ID: 2BXPZ-S01 Shenzhenjunyuelinghangkeji Co., Ltd., accepts to maintain an agent of service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. FCC US Agent, LLC, accepts as of the date of the filing of this application, the obligation of being the designated agent for the purpose of accepting service of process on behalf of Shenzhenjunyuelinghangkeji Co., Ltd.for FCC ID: 2BXPZ-S01 An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Designated Agent Information: Company Name: FCC US Agent, LLC FRN: 0033402884 Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Contact Person: Tim Payne Phone: 708-571-3148 Email: [email protected] Sincerely, Company: Shenzhenjunyuelinghangkeji Co., Ltd. Address: Building 3, Unit 2022, Phase II, Sunshine Yuehai Garden, No. 3818 Baishi Road, Yuegui Community, Yuehai Subdistrict, Nanshan District, Shenzhen Yanluo Street, Bao'an District, Shenzhen, China. Designated Agent: FCC US Agent, LLC Company Representative: Qiao Peng Designated Agent Representative: Tim Payne Signature: Email: [email protected] Tel: 13828819881 Signature:

Shenzhenjunyuelinghangkeji Co., Ltd. (August 25, 2026) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR (selfie stick / S01, S01S, S02, S02S, S03, S03S, S05, S05S, S07, S08, R1, R1S, R1L, R1LS # FCC ID: 2BXPZ-S01 #) To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the (Schematics, Block diagram, Operation description) required to be submitted with this application be permanently withheld from public review. These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Please contact me if there is any information you may need. Sincerely, Signature: Name Qiao Peng Position CEO Company Name Shenzhenjunyuelinghangkeji Co., Ltd. Address Building 3, Unit 2022, Phase II, Sunshine Yuehai Garden, No. 3818 Baishi Road, Yuegui Community, Yuehai Subdistrict, Nanshan District, Shenzhen Tel 13828819881 Fax / Email [email protected]

Differences Description We Shenzhenjunyuelinghangkeji Co., Ltd. state: Product name: Building Kit Sets Model: S01, S01S, S02, S02S, S03, S03S, S05, S05S, S07, S08, R1, R1S, R1L, R1LS All model’s the function, software, PCB Layout, RF Chip, component, antenna and electric circuit are the same, except name of the model and the appearance difference. Signature: Name Qiao Peng Position CEO Company Name Shenzhenjunyuelinghangkeji Co., Ltd. Address Building 3, Unit 2022, Phase II, Sunshine Yuehai Garden, No. 3818 Baishi Road, Yuegui Community, Yuehai Subdistrict, Nanshan District, Shenzhen Tel 13828819881 Fax / Email [email protected]

Shenzhenjunyuelinghangkeji Co., Ltd. (August 25, 2026) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize (Shenzhen Alpha Product Testing Co., Ltd.) to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Signature: Name Qiao Peng Position CEO Company Name Shenzhenjunyuelinghangkeji Co., Ltd. Address Building 3, Unit 2022, Phase II, Sunshine Yuehai Garden, No. 3818 Baishi Road, Yuegui Community, Yuehai Subdistrict, Nanshan District, Shenzhen Tel 13828819881 Fax / Email [email protected]

FCC ID: 2BXPZ-S01 FCC ID: 2BXPZ-S01 FCC ID: 2BXPZ-S01 FCC ID: 2BXPZ-S01 FCC ID: 2BXPZ-S01 FCC ID: 2BXPZ-S01 FCC ID: 2BXPZ-S01 FCC ID: 2BXPZ-S01

2cm 1.5cm Label Location FCC ID: 2BXPZ-S01 Shenzhenjunyuelinghangkeji Co., Ltd. Product name: selfie stick Model No.: S01

FCC ID: 2BXPZ-S01 FCC ID: 2BXPZ-S01 ANT FCC ID: 2BXPZ-S01 FCC ID: 2BXPZ-S01

FCC ID: 2BXPZ-S01 RF Exposure evaluation According to 447498 D04 Interim General RF Exposure Guidance v01 1-mW Test Exemption A single RF source is exempt RF device (from the requirement to show data demonstrating compliance to RF exposure limits, as previously mentioned) if the available maximum time-averaged power is no more than 1 mW, regardless of separation distance. This exemption applies to all operating configurations and exposure conditions, for the frequency range 100 kHz to 100 GHz, regardless of fixed, mobile, or portable device exposure conditions. This is a standalone exemption, and it cannot be applied in conjunction with any other test exemption. 1-mW Test Exemption for Multiple Sources The 1-mW exemption intended for single transmitters may be also applied to simultaneous transmission conditions, within the same host device, according one of the following criteria: a) When maximum available power each individual transmitting antenna within the same time averaging period is ≤ 1 mW, and the nearest parts of the antenna structures of the simultaneously operating transmitters are separated by at least 2 cm. b) When the aggregate maximum available power of all transmitting antennas is ≤ 1 mW in the same time-averaging period. This exemption may not be combined with any other exemption. SAR-Based Exemption This exemption is applicable to the frequency range between 300 MHz and 6 GHz, with test separation distances between 0.5 cm and 40 cm, and for all RF sources in fixed, mobile, and portable device exposure conditions. Accordingly, a RF source is considered an RF exempt device if its available maximum time-averaged (matched conducted) power or its effective radiated power (ERP), whichever is greater, are below a specified threshold. This exemption threshold was derived based on general population 1-g SAR requirements. This method shall only be used at separation distances from 0.5 cm to 40 cm and at frequencies from 0.3 GHz to 6 GHz (inclusive). Pth is given by follow Formulas “f” is in GHz, “d” is the separation distance (cm) FCC ID: 2BXPZ-S01 Simultaneous Transmission with SAR-based Exemptions For these cases, a device with multiple RF sources transmitting simultaneously will be considered an RF exempt device if the condition of following Formula is satisfied. (1-mW Test Exemption) As this equipment: Pt = 10 (Pm/10) where: Pt = transmitter output power in milliwatts, Pm = measured transmitter output power in dBm, So Pt =10 (-8.626/10) mW =0.1372 mW<1mW Then the SAR test is exempted.

ALPHA's reports is using a digital certificate that is trusted on Adobe's official server. If there is no digital certificate or the digital certificate shows damaged in your report. Please do not accept the report. E-mail: [email protected] Tel: 4008-3008-95 Website: http://www.a-lab.cn FCC REPORT Applicant : Shenzhenjunyuelinghangkeji Co., Ltd. Address of Applicant : Building 3, Unit 2022, Phase II, Sunshine Yuehai Garden, No. 3818 Baishi Road, Yuegui Community, Yuehai Subdistrict, Nanshan District, Shenzhen Yanluo Street, Bao'an District, Shenzhen, China. Manufacturer : Shenzhenjunyuelinghangkeji Co., Ltd. Address of Manufacturer : Building 3, Unit 2022, Phase II, Sunshine Yuehai Garden, No. 3818 Baishi Road, Yuegui Community, Yuehai Subdistrict, Nanshan District, Shenzhen Yanluo Street, Bao'an District, Shenzhen, China. Equipment under Test : selfie stick Model No. : S01, S01S, S02, S02S, S03, S03S, S05, S05S, S07, S08, R1, R1S, R1L, R1LS FCC ID : 2BXPZ-S01 Test Standard(s) : FCC Rules and Regulations Part 15 Subpart C Section 15.247, ANSI C63.10-2020 Report No. : A2605236-C04-R01 Issue Date : 2026/08/12 Issued By : Shenzhen Alpha Product Testing Co., Ltd. Building i, No.2, Lixin Road, Fuyong Street, Bao'an District,518103, Shenzhen City, Guangdong Province, P.R. China. «reportTypeImage» Shenzhen Al pha Product Testi ng C o., L td. R eport N o.:A2605236-C 04-R 01 Page 2 of 56 Table of Contents 1. Summary of Test Results ............................................................................................. 7 2. General Test Information .............................................................................................. 8 2.1. Description of EUT ........................................................................................................ 8 2.2. Accessories of EUT ...................................................................................................... 9 2.3. Block diagram of EUT configuration for test ................................................................. 9 2.4. Test mode description .................................................................................................. 9 2.5. Deviations of test standard ........................................................................................... 9 2.6. Test environment conditions ......................................................................................... 9 2.7. Test laboratory .............................................................................................................. 9 2.8. Measurement uncertainty ........................................................................................... 10 3. Spurious Emission ...................................................................................................... 11 3.1. Test equipment ........................................................................................................... 11 3.2. Block diagram of test setup ........................................................................................ 11 3.3. Limits ........................................................................................................................... 12 3.4. Assistant equipment used for test .............................................................................. 13 3.5. Test procedure ............................................................................................................ 13 3.6. Test result ................................................................................................................... 14 3.7. Test data ..................................................................................................................... 15 4. RF Conducted Spurious Emissions ............................................................................ 18 4.1. Test equipment ........................................................................................................... 18 4.2. Block diagram of test setup ........................................................................................ 18 4.3. Limits ........................................................................................................................... 18 4.4. Assistant equipment used for test .............................................................................. 19 4.5. Test procedure ............................................................................................................ 19 4.6. Test result ................................................................................................................... 19 5. Power Line Conducted Emissions .............................................................................. 20 5.1. Test equipment ........................................................................................................... 20 5.2. Block diagram of test setup ........................................................................................ 20 5.3. Limits ........................................................................................................................... 20 5.4. Assistant equipment used for test .............................................................................. 20 5.5. Test procedure ............................................................................................................ 20 5.6. Test result ................................................................................................................... 21 6. Duty Cycle ................................................................................................................... 22 6.1. Test equipment ........................................................................................................... 22 6.2. Block diagram of test setup ........................................................................................ 22 6.3. Limits ......................................................................…

Text truncated - open the document above for the full version.

Summary Inverted F Antenna Specification ITEM ANT SPEC Model Name 2.4G ANT Center Frequency Horizontal Vertical 2400MHz 2450MHz 2500MHz 2400MHz 2450MHz 2500MHz -1.26 -0.76 -0.58 -5.25 -2.46 -1.86 MAX. Gain -0.58dBi Polarization Horizontal and Vertical Azimuth Beam Pattern Omni-directional Impedance 50 Ohm Antenna Length 37.38mm Antenna type PCB Antenna Manufacture Yichip Microelectronics (Hangzhou) Co.,Ltd. Test Company TA Technology (Shanghai) Co., Ltd. Test Address Building 1, No. 400, Fangchun Road, China (Shanghai) Pilot Free Trade Zone Test Instrument Keysight E5071B Antenna Photo & Length (mm) Horizontal: 2400 MHz 2450 MHz 2500 MHz Power (dBm) Max: 0 Min: -40 Scale: 5/div Frequency (MHz) Gain(dBi) Max Min Avg 2400 -1.26174 -30.0801 -7.18716 2450 -0.765802 -36.5604 -7.48023 2500 -0.585582 -22.0315 -6.59127 Vertical: 2400 MHz 2450 MHz 2500 MHz Power (dBm) Max: 0 Min: -30 Scale: 5/div Frequency (MHz) Gain(dBi) Max Min Avg 2400 -5.2537 -22.1424 -12.4294 2450 -2.4652 -24.5837 -10.4702 2500 -1.86120 -29.5214 -9.20432 3D Radiation Pattern ANT Test Labs：Attestation of Global Compliance Co., Ltd.

FCC ID: 2BXPZ-S01 1.1. Photo of Radiated Emission test FCC ID: 2BXPZ-S01