2BXXK-X9-C03Stir-fry machine

FCC Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

Rev 1/26/2023 Changsha Zhangkonghuohou Technology Co.,Ltd Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2026-09-03 FCC ID: 2BXXK-X9-C03 Ref. #1: Attestation Statements Part 2.911(d)(5)(i) Filing Changsha Zhangkonghuohou Technology Co.,Ltd certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Changsha Zhangkonghuohou Technology Co.,Ltd certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Ref. #2: Attestation Statements Part 2.911(d)(5)(ii) Filing Changsha Zhangkonghuohou Technology Co.,Ltd certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Applicant: Changsha Zhangkonghuohou Technology Co.,Ltd Address: 3F, Building 6, Xiangjiang Science and Technology Innovation Park, Yuelu District, Changsha City, Hunan Province China Contact Person: Hu Tie Tel.: 18027664708 Email: [email protected] Sincerely, Signature:

Attestation Statements Date: 2026-09-03 TO: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046, USA RE: Attestation Statements Part 2.911(d)(7) request for(FCC ID: 2BXXK-X9-C03) Changsha Zhangkonghuohou Technology Co.,Ltd, the undersigned, hereby authorize FCC US Agent, LLC to act as our designated agent for service of process, Changsha Zhangkonghuohou Technology Co.,Ltd accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. FCC US Agent, LLC accepts the responsibility to act as designated agent for service of process. Applicant Information： Company name: Changsha Zhangkonghuohou Technology Co.,Ltd Contact Name: Hu Tie Address: 3F, Building 6, Xiangjiang Science and Technology Innovation Park, Yuelu District, Changsha City, Hunan Province China Telephone No: 18027664708 Email: [email protected] FRN: 0038825873 Signature: Hu Tie Agent Information: Company Name: FCC US Agent, LLC Address:3722 Illinois Avenue, Saint Charles, IL, 60174, USA FRN: 0033402884 Contact Name: Tim Payne Telephone No: 708-571-3148 Email: [email protected] Signature: Tim Payne

Changsha Zhangkonghuohou Technology Co.,Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: September 3, 2026 Subject; Request for Confidentiality FCC ID: 2BXXK-X9-C03 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure SOFTWARE SECURITY REQUIREMENTS FOR U-NII DEVICES In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Hu Tie Title: Product Director

Effective Date: April 2, 2020 QSF 7.6.4-8 – Agent Authorization Letter Template Page 1 of 1 Revision Date: Revision: 0 Changsha Zhangkonghuohou Technology Co.,Ltd Date：2026-09-03 Product Model Number: X9-C03 FCC ID：2BXXK-X9-C03 To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following: • Testing • Approval applications and procedures We declare that QAI Laboratories Ltd. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by QAI Laboratories Ltd. on our behalf shall have the same effect as acts of our own. Signature: By: Hu Tie Contact Listed on FCC Wesbite Title: Product Director Email: [email protected] On behalf of: Changsha Zhangkonghuohou Technology Co.,Ltd

Page 1 of 4 Report No.: LGT26H080 Appendix - External Photographs of EUT Constructional Details Photo 1 Photo 2 Wi-Fi Antenna Page 2 of 4 Report No.: LGT26H080 Appendix - External Photographs of EUT Constructional Details Photo 3 Photo 4 Page 3 of 4 Report No.: LGT26H080 Appendix - External Photographs of EUT Constructional Details Photo 5 Photo 6 Page 4 of 4 Report No.: LGT26H080 Appendix - External Photographs of EUT Constructional Details Photo 7

Label Label Size:15cm * 10cm

Page 1 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 1 Photo 2 Page 2 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 3 Photo 4 Page 3 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 5 Photo 6 Page 4 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 7 Photo 8 Page 5 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 9 Photo 10 Page 6 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 11 Photo 12 Page 7 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 13 Photo 14 Page 8 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 15 Photo 16 Page 9 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 17 Photo 18 Page 10 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 19 Photo 20 Page 11 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 21 Photo 22 Page 12 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 23 Photo 24 Page 13 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 25 Photo 26 Page 14 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 27 Photo 28 Page 15 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 29 Photo 30 Wi-Fi ANT Page 16 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 31 Photo 32 Page 17 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 33 Photo 34 Page 18 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 35 Photo 36 Page 19 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 37 Photo 38 Page 20 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 39 Photo 40 Page 21 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 41 Photo 42 Page 22 of 22 Report No.: LGT26H080 Appendix - Internal Photographs of EUT Constructional Details Photo 43

The test report is effective only with both signature and specialized stamp. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report only apply to the tested sample. Shenzhen LGT Test Service Co., Ltd. Tel: 0755-89668180 E-mail:[email protected] Web: www.lgt-cert.com Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Page 1 of 8 EMF TEST REPORT Product Name: Stir-fry machine Model Number: X9-C03 FCC ID: 2BXXK-X9-C03 Issued For : Changsha Zhangkonghuohou Technology Co.,Ltd 3F, Building 6, Xiangjiang Science and Technology Innovation Park, Yuelu District, Changsha City, Hunan Province China Issued By : Shenzhen LGT Test Service Co., Ltd. Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Report Number: LGT26H080HA01 Sample Received Date: Aug. 10, 2026 Date of Test: Aug. 10, 2026 ~ Aug. 27, 2026 Date of Issue: Aug. 27, 2026 Report No.: LGT26H080HA01 Page 2 of 8 TEST REPORT CERTIFICATION Applicant: Changsha Zhangkonghuohou Technology Co.,Ltd Address: 3F, Building 6, Xiangjiang Science and Technology Innovation Park, Yuelu District, Changsha City, Hunan Province China Manufacturer: Changsha Zhangkonghuohou Technology Co.,Ltd Address: Workshop & Connecting Corridor 101‑1A, Building 3, Changsha Xintai Instrument Co., Ltd., No.89 Yulin Road, Xueshi Sub‑district, Yuelu District, Changsha City, Hunan Province, P.R.China Product Name: Stir-fry machine Trademark: Model Number: X9-C03 Sample Status: Normal APPLICABLE STANDARDS STANDARD TEST RESULTS FCC 47 CFR §2.1091 KDB 447498 D01 General RF Exposure Guidance v06 PASS Prepared by: Approved by: Chris Chen Engineer Technical Director Report No.: LGT26H080HA01 Page 3 of 8 TABLE OF CONTENTS 1 . GENERAL INFORMATION 5 1.1 GENERAL DESCRIPTION OF THE EUT 5 1.2 TEST LABORATORY 5 2 . FCC 47CFR §2.1091 REQUIREMENT 6 2.1 TEST STANDARDS 6 2.2 LIMIT 6 2.3 EUT OPERATION CONDITION 7 2.4 CLASSIFICATION 7 2.5 TEST RESULT 8 Report No.: LGT26H080HA01 Page 4 of 8 Revision History Rev. Issue Date Revisions 00 Aug. 27, 2026 Initial Issue Report No.: LGT26H080HA01 Page 5 of 8 1. GENERAL INFORMATION 1.1 GENERAL DESCRIPTION OF THE EUT Product Name: Stir-fry machine Test Model Number: X9-C03 Series Number: N/A Model Difference: N/A Frequency Bands: 2.4G WLAN IEEE 802.11b/g/n(20MHz): 2412~2462MHz Rating: Input: AC 208V 50/60Hz 3A Hardware Version: N/A Software Version: N/A 1.2 TEST LABORATORY Company Name: Shenzhen LGT Test Service Co., Ltd. Address: Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Accreditation Certificate: FCC Registration No.: 746540 CAB ID: CN0136 Report No.: LGT26H080HA01 Page 6 of 8 2. FCC 47CFR §2.1091 REQUIREMENT 2.1 TEST STANDARDS The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The gain of the antennas used in the product is extracted from the Antenna data sheets provided and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis Transmission formula is far field assumption, the calculated result of that is an over-prediction for near field power density. It is taken as worst case to specify the safety range. 2.2 LIMIT According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of the human exposure to radio-frequency (RF) radiation as specified in 1.1307 (b) Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm²) Limits for Occupational / controlled Exposures 0.3-3.0 614 1.63 *(100) 3.0-30 1842/f 4.89/f *(900/f 2 ) 30-300 61.4 0.163 1.0 300 - 1500 -- -- F/300 1500 – 100000 -- -- 5.0 Limits for General population / Uncontrolled Exposure 0.3-1.34 614 1.63 *(100) 1.34-30 824/f 2.19/f *(180/f 2 ) 30-300 27.5 0.073 0.2 300 - 1500 -- -- F/1500 1500 – 100000 -- -- 1.0 F= Frequency in MHz * = Plane-wave equivalent power density. Friss Formula Friss Transmission Formula: Pd = (Pout * G) / (4*pi*r²) Where Pd = power density in mW/cm² Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = Distance between observation point and the center of radiator in cm If we know the maximum gain of the antenna and the total output power to the antenna, through calculation, we will know MPE value at distance 20cm. Report No.: LGT26H080HA01 Page 7 of 8 2.3 EUT OPERATION CONDITION EUT was enabled to transmit and receive at lowest, middle and highest channels. 2.4 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. Warning statement to the user for keeping at least 20cm or more separation distance from the antenna should be included in the User manual. So, this device is classified as Mobile device. Report No.: LGT26H080HA01 Page 8 of 8 2.5 TEST RESULT Turn up Result Mode Turn up Power 2.4G WIFI-802.11b 15±1dBm 2.4G WIFI-802.11g 12.5±1.5dBm 2.4G WIFI-802.11n(HT20) 12.5±1.5dBm The MPE result of worst mode: RF Function Max Turn up Power (dBm) Max Turn up Power (mW) ANT Gain (dBi) ANT Gain (gain of antenna in linear scale) Power Density (mW/cm²) Limit (mW/cm²) Ratio Result 2.4G WIFI 16.00 39.81 2 1.58 0.013 1 0.013 Pass Note: 1. The RF Exposure is less than the limit, complies with the exemption requirements. ※※※※※END OF THE REPORT※※※※※

承认书 APPROVAL SHEET C u s t o m e r（客户名称）： Sp e c i f i c a t i o n（规格）： 小蘑菇头天线（m10*1.5） C P / N（ 客 户 料 号 ） ： QW P/N（和欣瑞料号）： HXR-XMG-M10-WIFI-IPEX-40CM D a t e（ 日 期 ） ： 2026-06-16 QinWei Approved Approved (核 准) Checked (审 核) Prepared (承 办) 唐君 唐心怡 黄斌 Customer Approved Approved (核 准) Checked (审 核) Inspected (检验) 深圳市和欣瑞科技有限公司 Shenzhen Hexinrui Technology Co., Ltd 深圳市龙岗区坪地石壁西路30号 TEL: 18025407113 No.30 Shibi West Road, Pingdi Subdistrict, Longgang District, Shenzhen City, Guangdong Province, P.R.China 深圳市和欣瑞科技有限公司 Shenzhen Hexinrui Technology Co., Ltd Antenna Specification(天线规格) Item（项目） Specification（规格） Comment（误差） Impedance（阻抗） 50Ω Freq. Range（频率范围） 2400-2500MHz Antenna Type（天线类型） Peak Gain（峰值增益） 2dBi VSWR（驻波比） 2400-2500MHz≤2.0 Polarization Type（极化方式） Vertical垂直 Radiation Type（辐射类型） Omnidirectional全向 Connector Type（插口） IPEX RF Cable Type（线缆类型） RG178棕色 Cable Length (线长) 400mm Dimension（尺寸）） 28*31mm Operating Temp（工作温度） -20°C～+75°C Storage Temp（储存温度） -20°C～+75°C External antenna 深圳市和欣瑞科技有限公司 Shenzhen Hexinrui Technology Co., Ltd 1. SWR/驻波图 2.3D Radiation Pattern/3D 辐射方向图 深圳市和欣瑞科技有限公司 Shenzhen Hexinrui Technology Co., Ltd

The test report is effective only with both signature and specialized stamp. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report only apply to the tested sample. Shenzhen LGT Test Service Co., Ltd. Tel: 0755-89668180 E-mail:[email protected] Web: www.lgt-cert.com Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Page 1 of 59 RF TEST REPORT Product Name: Stir-fry machine Model Number: X9-C03 FCC ID: 2BXXK-X9-C03 Issued For : Changsha Zhangkonghuohou Technology Co.,Ltd 3F, Building 6, Xiangjiang Science and Technology Innovation Park, Yuelu District, Changsha City, Hunan Province China Issued By : Shenzhen LGT Test Service Co., Ltd. Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Report Number: LGT26H080RF01 Sample Received Date: Aug. 10, 2026 Date of Test: Aug. 10, 2026 ~ Aug. 27, 2026 Date of Issue: Aug. 27, 2026 Report No.: LGT26H080RF01 Page 2 of 59 TEST REPORT CERTIFICATION Applicant: Changsha Zhangkonghuohou Technology Co.,Ltd Address: 3F, Building 6, Xiangjiang Science and Technology Innovation Park, Yuelu District, Changsha City, Hunan Province China Manufacturer: Changsha Zhangkonghuohou Technology Co.,Ltd Address: Workshop & Connecting Corridor 101‑1A, Building 3, Changsha Xintai Instrument Co., Ltd., No.89 Yulin Road, Xueshi Sub‑district, Yuelu District, Changsha City, Hunan Province, P.R.China Product Name: Stir-fry machine Trademark: Model Number: X9-C03 Sample Status: Normal APPLICABLE STANDARDS STANDARD TEST RESULTS FCC Part 15.247, Subpart C ANSI C63.10-2020 + Cor. 1-2023+C63.10a-2024 + Errata to C63.10a-2024 PASS Prepared by: Approved by: Chris Chen Vita Li Engineer Technical Director Report No.: LGT26H080RF01 Page 3 of 59 Table of Contents Page 1. SUMMARY OF TEST RESULTS 6 1.1 TEST LABORATORY 7 1.2 MEASUREMENT UNCERTAINTY 7 2. GENERAL INFORMATION 8 2.1 GENERAL DESCRIPTION OF THE EUT 8 2.2 DESCRIPTION OF THE TEST MODES 10 2.3 TEST SOFTWARE AND POWER LEVEL 10 2.4 DESCRIPTION OF NECESSARY ACCESSORIES AND SUPPORT UNITS 11 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 12 3. EMC EMISSION TEST 14 3.1 CONDUCTED EMISSION MEASUREMENT 14 3.2 RADIATED EMISSION MEASUREMENT 19 4. CONDUCTED SPURIOUS & BAND EDGE EMISSION 29 4.1 LIMIT 29 4.2 TEST PROCEDURE 29 4.3 DEVIATION FROM STANDARD 29 4.4 TEST SETUP 29 4.5 EUT OPERATION CONDITIONS 29 4.6 TEST RESULTS 29 5. POWER SPECTRAL DENSITY TEST 30 5.1 LIMIT 30 5.2 TEST PROCEDURE 30 5.3 DEVIATION FROM STANDARD 30 5.4 TEST SETUP 30 5.5 EUT OPERATION CONDITIONS 30 5.6 TEST RESULTS 30 6. BANDWIDTH TEST 31 6.1 LIMIT 31 6.2 TEST PROCEDURE 31 6.3 DEVIATION FROM STANDARD 31 6.4 TEST SETUP 31 6.5 EUT OPERATION CONDITIONS 31 6.6 TEST RESULTS 31 Report No.: LGT26H080RF01 Page 4 of 59 7. PEAK OUTPUT POWER TEST 32 7.1 LIMIT 32 7.2 TEST PROCEDURE 32 7.3 DEVIATION FROM STANDARD 32 7.4 TEST SETUP 32 7.5 EUT OPERATION CONDITIONS 32 7.6 TEST RESULTS 32 8. ANTENNA REQUIREMENT 33 8.1 STANDARD REQUIREMENT 33 8.2 EUT ANTENNA 33 APPENDIX I - TEST RESULTS 34 1. DUTY CYCLE 34 2. BANDWIDTH 38 3. MAXIMUM CONDUCTED OUTPUT POWER 45 4. MAXIMUM POWER SPECTRAL DENSITY 46 5. UNWANTED EMISSIONS IN NON-RESTRICTED FREQUENCY BANDS 50 APPENDIX II - MEASUREMENT PHOTOS 59 Report No.: LGT26H080RF01 Page 5 of 59 Revision History Rev. Issue Date Revisions 00 Aug. 27, 2026 Initial Issue Report No.: LGT26H080RF01 Page 6 of 59 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: KDB 558074 D01 15.247 Meas Guidance v05r02. FCC Part 15.247,Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS -- 15.247 (a)(2) 6dB Bandwidth PASS -- 15.247 (b)(3) Output Power PASS -- 15.209 Radiated Spurious Emission PASS -- 15.247 (d) Conducted Spurious & Band Edge Emission PASS -- 15.247 (e) Power Spectral Density PASS -- 15.205 Restricted Band Edge Emission PASS -- Part 15.247(d)/ Part 15.209(a) Band Edge Emission PASS -- 15.203 Antenna Requirement PASS -- NOTE: (1) ‘N/A’ denotes test is not applicable in this Test Report. (2) All tests are according to ANSI C63.10-2020 + Cor. 1-2023+C63.10a-2024 + Errata to C63.10a-2024. Report No.: LGT26H080RF01 Page 7 of 59 1.1 TEST LABORATORY Company Name: Shenzhen LGT Test Service Co., Ltd. Address: Room 205, Building 13, Zone B, Zhenxiong Industrial Park, No.177, Renmin West Road, Jinsha, Kengzi Street, Pingshan District, Shenzhen, Guangdong, China Accreditation Certificate: FCC Registration No.: 746540 CAB ID: CN0136 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. No. Item Uncertainty 1 Occupied Channel Bandwidth ±0.46% 2 RF Output Power, Conducted ±0.71dB 3 Power Spectral Density, Conducted ±1.57dB 4 Unwanted Emission, Conducted ±0.63dB 5 Conducted emission ±2.80dB 6 All Emissions, Radiated (0.009-30MHz) ±2.16dB 7 All Emissions, Radiated (30MHz-1GHz) ±4.61dB 8 All Emissions, Radiated (1GHz-18GHz) ±5.49dB 9 All Emissions, Radiated (18GHz-40GHz) ±4.31dB 10 Temperature ±0.5°C 11 Humidity ±2% 12 Duty Cycle ±2.3% Note: The measurement uncertainty is not included in the test result. Report No.: LGT26H080RF01 Page 8 of 59 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF THE EUT Product Name: Stir-fry machine Test Model Number: X9-C03 Series Number: N/A Model Difference: N/A Product Description: Operation Frequency: 802.11b/g/n(20MHz): 2412~2462MHz Modulation Type: 802.11b(DSSS):CCK,DQPSK,DBPSK 802.11g(OFDM):BPSK,QPSK,16-QAM,64-QAM 802.11n(OFDM):BPSK,QPSK,16-QAM,64-QAM Number of Channel: 802.11b/g/n(20MHz): 11CH Antenna Designation: External antenna Antenna Gain(dBi): 2 Channel List: Please refer to the Note 3. Rating: Input: AC 208V 50/60Hz 3A Hardware Version: N/…

Text truncated - open the document above for the full version.

Page 1 of 2 Report No.: LGT26H080 Appendix - Test Setup photos Set-up for Radiated Spurious Emission, Below 1GHz Set-up for Radiated Spurious Emission, Above 1GHz Page 2 of 2 Report No.: LGT26H080 Set-up for Conducted Emission