2BXZO-21046COJulio

Product Name: Julio Operation without remote control After power-on, blue light flashes. Short press the power button to cycle modes: Thrusting → Vibration → Thrusting & Vibration →Blue light flashing. Each mode has 3 speed levels, which can be adjusted via the remote control. Charging Indicator Status 0~50% battery: Red light flashing 50~99% battery: Amber light flashing Fully charged: Steady green light (no flashing) Remote Control Instructions In Thrusting Mode: pressing '+' increases thrusting speed. In Thrusting Mode: pressing '−' decreases thrusting speed. In Vibration Mode: pressing '+' increases vibration intensity. In Vibration Mode: pressing '−' decreases vibration intensity. In Vibration Mode: pressing '–' decreases vibration intensity. FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. “This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.” « Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme sile brouillage est susceptible d'en compromettre le fonctionnement. » The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. L’appareil a été évalué pour répondre aux exigences générales en matière d’exposition aux RF. L’appareil peut être utilisé en condition d’exposition portable sans restriction.

Rev 6/05/2026 Dongguan Conbridge Industry Co., Ltd. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 08-28-2026 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2BXZO-21046CO [Dongguan Conbridge Industry Co., Ltd.] certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. [Dongguan Conbridge Industry Co., Ltd.] certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Device is inherently compliant based on hardware limitations or software controls. or A Software Bill of Materials (SBOM) is provided to the TCB for review, and The end-user or third parties cannot install additional software on this device. Sincerely, (Applicant signature) (Applicant printed name) Lemon feng Rev 6/05/2026 Dongguan Conbridge Industry Co., Ltd. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 08-28-2026 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2BXZO-21046CO [Dongguan Conbridge Industry Co., Ltd.] certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) Lemon feng

Dongguan Conbridge Industry Co., Ltd. U.S. Agent Letter of Attestation To: Federal Communications Commission 7435 Oakland Mills Road, Columbia, MD 21046, USA Date: August 28, 2026 Ref: Attestation Statement – Part 2.911(d)(7) filing FCC ID: 2BXZO-21046CO Dongguan Conbridge Industry Co., Ltd.(“the applicant”) certifies that, as of the date of the filing of the application, GLOBAL PRODUCT PROMOTION COMMERCE CO., LTD. (“the agent”) is our designated U.S. agent for service of process for the above reference FCC ID. The applicant accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges it is our responsibility to inform the FCC whenever the agent information changes. GLOBAL PRODUCT PROMOTION COMMERCE CO., LTD. ("the agent) understand it is the agent's obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address. Designated U.S. Agent Company Name: GLOBAL PRODUCT PROMOTION COMMERCE CO., LTD. FRN: 0037700671 Address: 350 NORTHERN BLVD STE 324-1331, ALBANY, NY, 12204, USA Signature: Contact Person: David Kim Tel: (949)254-2565 Email: [email protected] Applicant Company Name: Dongguan Conbridge Industry Co., Ltd. FRN: 0038838181 Address: No.790 Jian'an Road, Chang'an town, Dongguan City, Guangdong, China. Signature: Contact Person: Lemon feng Tel: 18211307641 Email: [email protected]

Dongguan Conbridge Industry Co., Ltd. Date: August 28, 2026 Product Model Number: 21046-CO FCC ID: 2BXZO-21046CO To whom it may concern, Re: Product Certification Representative Authorization Letter We authorize QAI Laboratories Ltd. 3980 North Fraser Way, Burnaby B.C. Canada V5J 5K5 to act on our behalf on all matters concerning the above named equipment. This shall include the following: • Testing • Approval applications and procedures We declare that QAI Laboratories Ltd. is allowed to forward all information related to the approval project to the applied certification body and to the notification entities and to discuss any issues concerning the approval application. Any and all acts carried out by QAI Laboratories Ltd. on our behalf shall have the same effect as acts of our own. Signature： By: Lemon feng Title: Manager Email: [email protected] Telephone: 18211307641 On behalf of: Dongguan Conbridge Industry Co., Ltd.

Dongguan Conbridge Industry Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: September 3, 2026 Subject; Request for Confidentiality FCC ID: 2BXZO-21046CO To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Software Security Requirements for UNII devices It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature： By: Lemon feng Title: Manager

Report No: SSP26080215-1 FCC ID: 2BXZO-21046CO Annex A. EUT External Photos Model: 21046-CO EUT View 1 EUT View 2 Report No: SSP26080215-1 FCC ID: 2BXZO-21046CO EUT View 3 EUT View 4 Report No: SSP26080215-1 FCC ID: 2BXZO-21046CO EUT View 5 EUT View 6 Report No: SSP26080215-1 FCC ID: 2BXZO-21046CO EUT View 7

Report No: SSP26080215-1 FCC ID: 2BXZO-21046CO Annex D. Label and Information FCC Label Sample Label Size:1cm*0.5cm FCC Label Specifications Text is Black in color and is justified. Labels are printed in indelible ink on permanent adhesive backing or silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Where the EUT is constructed in two or more sections connected by wires and marketed together, the above statement is required to be affixed only to the main control unit. When the EUT is so small or for such use that it is not practicable to place the statement on it, the above information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. FCC Label Location

Report No: SSP26080215-1 FCC ID: 2BXZO-21046CO Annex B. EUT Internal Photos EUT Internal View 1 EUT Internal View 2 PCB Antenna Report No: SSP26080215-1 FCC ID: 2BXZO-21046CO EUT Internal View 3 EUT Internal View 4 433 Receiving antenna Report No: SSP26080215-1 FCC ID: 2BXZO-21046CO EUT Internal View 5

FCC ID: 2BXZO-21046CO RF Exposure Evaluation According to KDB 447498 D01 General RF Exposure Guidance v06 and part 2.1093，Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition(s), listed below, is (are) satisfied. For 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extremity SAR, where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison Here, The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. For BLE Max Conducted Power(dBm) Tune-up Power(dBm) Max Tune-up Power(dBm) Max Power(mW) Frequency(MHz) Min. distance(mm) Calc. thresholds limit -2.8 -2(±1) -1 0.79 2402 5 0.2448745 3.0 So a SAR test is not required

ANTENNASPECIFICATION Summary ITEMANT SPEC Model Name 21046-CO Antenna plate PCB Antenna Center Frequency HorizontalVertical 2400MH z 2450MH z 2500MH z 2400MH z 2450MH z 2500MH z -1.66 -0.840-6.16 -3.65 -2.21 MAX. Gain0 PolarizationHorizontal and Vertical Impedance50 Ohm Manufactur e Dongguan Conbridge Industry Co., Ltd. Anten n a Ph oto & Length (mm) No.790 Jian'an Road, Chang'an town, Dongguan City, Guangdong, China. Horizontal:2400MHz2450MHz2500MHz Power(dBm) Max:0Min:-40Scale:5/div FrequencyGain(dBi) (MHz)Max.MinAvg. 2400-1.66179-30.2813-8.78713 2450-0.847811-38.7595-7.87812 2500-0.000000-23.6329-6.99139 Vertical:2400MHz2450MHz2500MHz Power(dBm) Max:0Min:-30Scale:5/div FrequencyGain(dBi) (MHz)Max.MinAvg. 2400-6.1623-23.1425-12.5295 2450-3.6534-26.2866-10.6699 2500-2.21101-29.4381-9.58526

Report No: SSP26080215-1 FCC Test Report Page 1 of 47 FCC TEST REPORT FCC ID: 2BXZO-21046CO Report No. : SSP26080215-1 Applicant : Dongguan Conbridge Industry Co., Ltd. Product Name : Julio Model Name : 21046-CO Test Standard : FCC Part 15.247 Date of Issue : 2026-09-01 Shenzhen CCUT Quality Technology Co., Ltd. 1F, Building 35, Changxing Technology Industrial Park, Yutang Street, Guangming District, Shenzhen, Guangdong, China; (Tel.:+86-755-23406590 website: www.zrlklab.com) This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd. Report No: SSP26080215-1 FCC Test Report Page 2 of 47 Test Report Basic Information Applicant..................................: Dongguan Conbridge Industry Co., Ltd. Address of Applicant...............: No.790 Jian'an Road, Chang'an town, Dongguan City, Guangdong, China. Manufacturer..........................: Dongguan Conbridge Industry Co., Ltd. Address of Manufacturer........: No.790 Jian'an Road, Chang'an town, Dongguan City, Guangdong, China. Product Name.........................: Julio Brand Name.............................: - Main Model..............................: 21046-CO Series Models..........................: - Test Standard..........................: FCC Part 15 Subpart C KDB 558074 D01 15.247 Meas Guidance v05r02 ANSI C63.4-2014 ANSI C63.10-2020+Cor 1-2023+C63.10a-2024 + Errata to C63.10a-2024 Date of Test .............................: 2026-08-10 to 2026-09-01 Test Result...............................: PASS Tested By ................................: (Colin Chen) Reviewed By............................: (Lorzix Luo) Authorized Signatory............: (Lahm Peng) Note : This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by Shenzhen CCUT Quality Technology Co., Ltd.. All test data presented in this test report is only applicable to presented test sample. Report No: SSP26080215-1 FCC Test Report Page 3 of 47 CONTENTS 1. General Information ....................................................................................................................................................5 1.1 Product Information .............................................................................................................................................5 1.2 Test Setup Information..........................................................................................................................................6 1.3 Compliance Standards ...........................................................................................................................................7 1.4 Test Facilities ........................................................................................................................................................7 1.5 List of Measurement Instruments ..........................................................................................................................8 1.6 Measurement Uncertainty .....................................................................................................................................9 2. Summary of Test Results ........................................................................................................................................... 10 3. Antenna Requirement ............................................................................................................................................... 11 3.1 Standard and Limit.............................................................................................................................................. 11 3.2 Test Result .......................................................................................................................................................... 11 4. Conducted Emissions ................................................................................................................................................ 12 4.1 Standard and Limit.............................................................................................................................................. 12 4.2 Test Procedure.................................................................................................................................................... 12 4.3 Test Data and Results .......................................................................................................................................... 13 5. Radiated Emissions ................................................................................................................................................... 16 5.1 Standard and Limit.............................................................................................................................................. 16 5.2 Test Procedure.................................................................................................................................................... 16 5.3 Test Data and Results .......................................................................................................................................... 18 6. Band-edge Emissions(Radiated) ............................................................................................................................... 33 6.1 Standard and Limit.............................................................................................................................................. 33 6.2 Test Procedure.................................................................................................................................................... 33 6.3 Test Data and Results .......................................................................................................................................... 33 7. Maximum Peak Conducted …

Text truncated - open the document above for the full version.

Report No: SSP26080215-1 FCC ID: 2BXZO-21046CO Annex C. Test Photos Conducted Emission Test View 1 Radiated Emission Test View Below 1GHz Report No: SSP26080215-1 FCC ID: 2BXZO-21046CO Radiated Emission Test View Above 1GHz