A3LCCAR210RWi-Fi/BLE combo module

Version 1.0 Samsung Electronics page 1 of 6 User manual of CCAR210R 1. Introduction CCAR210R is a Wi-Fi/BLE combo module compliant with IEEE802.11 b.g.n MAC (2.4GHz) and Bluetooth Low Energy (BLE5.0) optimized for low-power applications. The core chipset is from Realtek, part number SDA8700CSM. 2. Hardware Architecture: 2.1 Main Chipset Information Item Vendor Part Number IEEE802.11 b.g.n(2.4GHz) BLE5.0 Realtek SDA8700CSM Version 1.0 Samsung Electronics page 2 of 6 3. Operational Description CCAR210R is the 802.11b/g/n MAC Wi-Fi and Bluetooth Low Energy BLE combo Module that acts as a communication controller for users of a wireless device to connect to SMART DEVICE - Features >IEEE 802.11 b/g/n (2.4GHz, 1x1) >20MHz/ 40MHz up to MCS7 supported >Low power Tx/Rx for short range application supported >Low power beacon listen mode >Very low power suspends mode (DLPS) >BLE >High power mode (8dbm, share the same PA with Wi-Fi) >Internal co-existence mechanism between Wi-Fi and BT to share the same antenna - Time base of the RF frequency For IF and RF frequency, a crystal(40MHz) is a clock reference. - Synthesizer Synthesizer inside Transceiver. Internal voltage controlled oscillator (VCO) provides the desired LO signal base on the phase-locked loop (PLL) with a relatively wide tuning range for this application. Internal fractional nPLL allows support for a wide range of reference clock frequencies - WIFI Transmission Base-band data is modulated and upconverted to the 2.4GHz ISM band, respectively. Base-band Processing (BBP) IC has DSSS (BPSK/QPSK/CCK) and OFDM (BPSK/QPSK/16QAM/64QAM) modulation function, it provides transmission data rate are 1, 2, 5.5, 11Mbps on DSSS and 6, 12, 18, 24, 36, 48, 54 Mbps on OFDM. Digital data signal will be converted to analog (TX IQ) signals through DAC in BBP IC, TX IQ pass through to low pass filter. TX I/Q signal use direct conversion (zero-IF) architecture converter to generate carrier frequency signal. Transceiver IC and internal PA magnify output power. - WIFI Receiver Reverse direction isolation of LNA inside Transceiver IC suppresses unwanted radiation. Then RF signal will be directly down to IF signal (RX IQ) and high frequency spurious emissions are suppressed by LPF. At last RX IQ signal will be demodulated digital data. - BLE The RADIO contains a 2.4 GHz radio receiver and a 2.4 GHz radio transmitter that is compatible with 1M/2Mbps Bluetooth® low energy mode. Version 1.0 Samsung Electronics page 3 of 6 - Product Details - WIFI > Data Modulation DSSS:CCK,BPSK,QPSK for 802.11b OFDM:BPSK,QPSK,16QAM,64QAM,256QAM for 802.11g,n > Frequency Range 2400-2483.5MHz - BLE > Data Modulation GFSK > Frequency Range 2400-2483.5MHz - Operating Temperature > -20 ~ +85°C Version 1.0 Samsung Electronics page 4 of 6 4. RF Exposure Statement FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Industry Canada Radiation Exposure Statement(D claration d’ exposition anx radiations): This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Cet quipement est conforme aux limites d’ exposition aux rayonnements IC tablies pour un environment noncom tr I. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Version 1.0 Samsung Electronics page 5 of 6 5. Notice FCC Statement Approval Statement CE Statement Hereby, we declare that this device is in compliance with the essential requirements and other relevant provisions of directive 1999/5/EC. FCC approval This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two Conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesirable operation. To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product. Contains Transmitter module FCC ID: A3LCCAR210R This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/ TV technician for help. -The OEM integrator is responsible for ensuring the end-user has no manual instruction to remove or install module. -The module is limited to installation in mobile or fixed applications. IC approval This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industr…

Text truncated - open the document above for the full version.

Samsung Electronics Co., LTD. 129, Samsu ng -ro , Yeongtong-gu Suwon-City, Gyeonggi-do, 16677, Korea Date: January 13 , 2021 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. UL Verification Services Certification Division 47173 Benicia Street Fremont, CA 945 38, USA To wh om it may concern: I, the undersigned, hereby a uthorize Ms. Chloe Lee/Manager of KCTL Inc. and hereafter referred to as KCTL to act on ou r b ehalf in all manners relating to application fo r equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Ms. Chlo e Lee/Manager of KCTL Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includ es FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing KCTL as our agent, we still recognize that we are responsible to: a)comply with the relevant provisions of the certification program; b)make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c)make claims regarding certification only in respect of the scope for which certification has been granted; d)do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e)upon suspension or cancellation of certification, discontinue use of all advertising m atter that contains any reference thereto and return any certification docume nts as required by the Certific ation Division; f) use certification only to indicate the products are certified as being in conformity with specified sta ndards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a m isleading m anner; h)ensure that any reference to our product certification in communication medi a such as docum ents, brochures or advertising, complies with the requirements of the Certification Division ; i)k eep a record of all complaints made known to the us relating to the pro duct’s c ompliance with requirements of the relevant standard and to make these records available to the Certification Division when requ ested; j)tak e appropriate action with respect to such complaints and any deficiencie s fou nd in products or services that affect compliance with the requirements for certific ation; k)docum e nt the actions taken. Th is authorization is valid until further written notice from the applicant. Sincerely Yours, Jenni Chun, General Manager Regulatory & Environmental Affairs Samsung Electronics America, Inc

Samsung Electronics Co., LTD. 129, Samsung -ro , Yeongtong-gu Suwon-City, Gyeonggi-do, 16677, Korea CONFIDENTIALITY REQUEST Fed eral Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 January 13, 2021 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, Samsung Electronics Co., Ltd. requests confidentiality for the following products : FCC ID Num ber Product Title/Model A3LCCAR210R Wi-Fi/BLE combo module / CCAR210R The following exhibits contain trade secrets and proprietary information that could be of benefit to our competitors regarding the design of our product. This material is not customarily available to the general public and we request that it be withheld from public inspection. We request that the following information submitted be held permanent confidential treatment. Permanent Confidential Request -. Schematics -. Block Diagram -. Operational Description -. Antenna specification We hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give temporary confidentiality of commercially sensitive information prior to product release. Short-Term Confidential Request -. External Photos -. Internal Photos -. Test set-up photo -. User Manual If you have any questions, please feel free to contact me at the address shown below. Sincerely, Jenni Chun / General manager

Applicant/Grantee Samsung Electronics Co., Ltd. FCC ID: A3LCCAR210R Section 15.212 Modular Transmitters Request for Modular Approval Request for Limited Modular Approval Requirements EUT Conditions Com ply (Y/N) Single Modular Approval Requirements 1 The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. This module is shielded with a shield can. Y 2 The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. OK Y 3 The modular transmitter must have its own power supply regulation. A DC-DC converter is configured for internal supply of the module. Y 4 The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. Connected to antenna with internal transmission line and matching. Y 5 The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between OK Y the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)). 6 The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. (A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. (B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC certified transmitter module(s).” Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. Mark the FCC-ID certification number on the module label. Y 7 The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the Module usage manuals were provided. Y application for equipment authorization. 8 The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. For RF exposure requests, ensure that RF specs are entered and adhered to within the approval source provided to all users fo this module. Y A limited modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured.

http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval External photos of EUT http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval

내열Label Design Information Size: 26.0 X 12.0 [mm] Color: White(print: Black) ※ CCAR210R PF1_ Label 26mm 12mm 4709-00XXXX MODEL: CCAR210R FCC ID: A3LCCAR210R R-C-SEC-CCAR210R CMIIT ID: ANATEL: IC: 649E-CCAR210R MOC: Made in Korea 4-R1.0 SN: DEVICE: MAC(W): MAC(B): Front of the module / Location of label

http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval Internal photos of EUT http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval Metal Antenna

verify No.056808167730 KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR21-SRF0012-B Page (2) of (12) KCTL-TIR001-003/3 KP20-05065 REPORT REVISION HISTORY Date Revision Page No 2021-01-14 Originally issued - 2021-01-19 Updated 11 2021-01-21 Updated 4 This report shall not be reproduced except in full, without the written approval of KCTL Inc. This document may be altered or revised by KCTL Inc. personnel only, and shall be noted in the revision section of the document. Any alteration of this document not carried out by KCTL Inc. will constitute fraud and shall nullify the document. This test report is a general report that does not use the KOLAS accreditation mark and is not related to KS Q ISO/IEC 17025 and KOLAS accreditation. Note. The report No. KR21-SRF0012-A is superseded by the report No. KR21-SRF0012-B. General remarks for test reports Nothing significant to report. KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR21-SRF0012-B Page (3) of (12) This test report shall not be reproduced, except in full, without the written approval KCTL-TIR001-003/3 KP20-05065 CONTENTS 1. General information ...................................................................................................... 4 2. Device information ........................................................................................................ 4 2.1. Frequency/channel operations ................................................................................ 4 3. Measurement uncertainty ............................................................................................. 6 4. RF Exposure ................................................................................................................. 7 4.1. Test results ............................................................................................................ 10 5. Measurement Equipment ............................................................................................ 12 KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR21-SRF0012-B Page (4) of (12) This test report shall not be reproduced, except in full, without the written approval KCTL-TIR001-003/3 KP20-05065 1. General information Client : Samsung Electronics Co., Ltd. Address : 129, Samsung-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Rep. of Korea Manufacturer : Samsung Electronics Co., Ltd. Address : 129, Samsung-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Rep. of Korea Laboratory : KCTL Inc. Address : 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea Accreditations : FCC Site Designation No: KR0040, FCC Site Registration No: 687132 VCCI Registration No. : R-20080, G-20078, C-20059, T-20056 Industry Canada Registration No. : 8035A KOLAS No.: KT231 2. Device information Equipment under test : Wi-Fi/BLE combo module Model : CCAR210R Frequency range : 2 402 ㎒ ~ 2 480 ㎒ (Bluetooth(BLE)) 2 412 ㎒ ~ 2 462 ㎒ (802.11b/g/n HT20) 2 422 ㎒ ~ 2 452 ㎒ (802.11n HT40) Modulation technique : Bluetooth(BLE)_GFSK WIFI(802.11b/g/n HT20/40)_DSSS, OFDM Number of channels : Bluetooth(BLE)_40 ch 2.4 GHz band: 11 ch (20 ㎒), 7 ch (40 ㎒), Power source : DC 5.0 V, DC 12.0 V Antenna type : Metal Antenna Antenna gain : Bluetooth(BLE) 0.5 ㏈i 2.4 ㎓ band 0.5 ㏈i Software version : v1.0 Hardware version : v1.0 Operation temperature : -20 °C ~ 85 °C KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR21-SRF0012-B Page (5) of (12) This test report shall not be reproduced, except in full, without the written approval KCTL-TIR001-003/3 KP20-05065 2.1. Frequency/channel operations This device contains the following capabilities: 802.11b/g/n HT20/40, Bluetooth Low Energy Ch. Frequency (㎒) 00 2 402 . . . . 19 2 440 . . . . 39 2 480 Table 2.1.1. Bluetooth Low Energy Ch. Frequency (㎒) 01 2 412 . . . . 06 2 437 . . . . 11 2 462 Table 2.1.2. 802.11b/g/n_HT20 mode Ch. Frequency (㎒) 03 2 422 . . . . 06 2 437 . . . . 09 2 452 Table 2.1.3. 802.11n_HT40 mode . KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR21-SRF0012-B Page (6) of (12) This test report shall not be reproduced, except in full, without the written approval KCTL-TIR001-003/3 KP20-05065 3. Measurement uncertainty The measurement uncertainties shown below were calculated in accordance with the requirements of ANSI C63.10-2013. All measurement uncertainty values are shown with a coverage factor of k=2 to indicated a 95 % level of confidence. The measurement data shown herein meets of exceeds the U CISPR measurement uncertainty values specified in CISPR 16-4-2 and thus, can be compared directly to specified limits to determine compliance. Parameter Expanded uncertainty (±) Conducted RF power 1.3 ㏈ KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR21-SRF0012-B Page (7) of (12) This test report shall not be reproduced, except in full, without the written approval KCTL-TIR001-003/3 KP20-05065 4. RF Exposure FCC Regulation This document is prepared to show compliance with the RF Exposure requirements as required in §1.1310 of the FCC rules and Regulations. The limit for Maximum Permissible Exposure (MPE), specified in FCC §1.1310, is listed in Table 1-1. According to FCC §1.1310: the criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in §1.1307(b). Table 1 – Limits for Maximum Permissible Exposure (MPE) Frequency Range (㎒) Electric Field Strength [V/m] Magnetic Field Strengt…

Text truncated - open the document above for the full version.

verify No.575881044560 KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR21-SRF0010-A Page (2 ) of (73) KCTL-TIR001-003/3 KP20-05065 REPORT REVISION HISTORY Date Revision Page No 2021-01-14 Originally issued - 2021-01-21 Updated 4 This report shall not be reproduced except in full, without the written approval of KCTL Inc. This document may be altered or revised by KCTL Inc. personnel only, and shall be noted in the revision section of the document. Any alteration of this document not carried out by KCTL Inc. will constitute fraud and shall nullify the document. This test report is a general report that does not use the KOLAS accreditation mark and is not related to KS Q ISO/IEC 17025 and KOLAS accreditation. Note. The report No. KR21-SRF0010 is superseded by the report No. KR21-SRF0010-A. General remarks for test reports Nothing significant to report. KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR21-SRF0010-A Page (3) of (73) This test report shall not be reproduced, except in full, without the written approval KCTL-TIR001-003/3 KP20-05065 CONTENTS 1. General information ...................................................................................................... 4 2. Device information ........................................................................................................ 4 2.1. Frequency/channel operations ................................................................................ 5 2.2. Duty Cycle Factor ................................................................................................... 6 3. Antenna requirement .................................................................................................... 8 4. Summary of tests .......................................................................................................... 9 5. Measurement uncertainty ........................................................................................... 10 6. Measurement results explanation example ................................................................ 11 7. Test results ................................................................................................................. 12 7.1. Maximum peak output power ................................................................................ 12 7.2. Peak Power Spectral Density ............................................................................... 16 7.3. 6 dB Bandwidth(DTS Channel Bandwidth) & 99% Bandwidth .............................. 21 7.4. Spurious Emission, Band Edge and Restricted bands .......................................... 31 7.5. Conducted Spurious Emission .............................................................................. 65 7.6. AC Conducted emission ....................................................................................... 70 8. Measurement equipment ............................................................................................ 73 KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR21-SRF0010-A Page (4) of (73) This test report shall not be reproduced, except in full, without the written approval KCTL-TIR001-003/3 KP20-05065 1. General information Client : Samsung Electronics Co., Ltd. Address : 129, Samsung-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Rep. of Korea Manufacturer : Samsung Electronics Co., Ltd. Address : 129, Samsung-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Rep. of Korea Laboratory : KCTL Inc. Address : 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea Accreditations : FCC Site Designation No: KR0040, FCC Site Registration No: 687132 VCCI Registration No. : R-20080, G-20078, C-20059, T-20056 Industry Canada Registration No. : 8035A KOLAS No.: KT231 2. Device information Equipment under test : Wi-Fi/BLE combo module Model : CCAR210R Frequency range : 2 402 ㎒ ~ 2 480 ㎒ (Bluetooth(BLE)) 2 412 ㎒ ~ 2 462 ㎒ (802.11b/g/n HT20) 2 422 ㎒ ~ 2 452 ㎒ (802.11n HT40) Modulation technique : Bluetooth(BLE)_GFSK WIFI(802.11b/g/n HT20/40)_DSSS, OFDM Number of channels : Bluetooth(BLE)_40 ch 2.4 GHz band: 11 ch (20 ㎒), 7 ch (40 ㎒), Power source : DC 5.0 V, DC 12.0 V Antenna type : Metal Antenna Antenna gain : Bluetooth(BLE) 0.5 ㏈i 2.4 ㎓ band 0.5 ㏈i Software version : v1.0 Hardware version : v1.0 Operation temperature : -20 °C ~ 85 °C KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR21-SRF0010-A Page (5) of (73) This test report shall not be reproduced, except in full, without the written approval KCTL-TIR001-003/3 KP20-05065 2.1. Frequency/channel operations This device contains the following capabilities: 802.11b/g/n HT20/40, Bluetooth Low Energy Ch. Frequency (㎒) 00 2 402 . . . . 19 2 440 . . . . 39 2 480 Table 2.1.1. Bluetooth Low Energy KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR21-SRF0010-A Page (6) of (73) This test report shall not be reproduced, except in full, without the written approval KCTL-TIR001-003/3 KP20-05065 2.2. Duty Cycle Factor Test mode Period (ms) On time (ms) Duty cycle Duty Cycle Factor (dB) (Linear) (%) DC 5 V 1M Bits/s, 37 Packet 0.625 0.394 0.629 6 62.96 2.01 2M Bits/s, 37 Packet 0.625 0.207 0.330 9 33.09 4.80 1M Bits/s, 255 Packet 2.497 2.134 0.854 6 85.46 0.68 2M Bits/s, 255 Packet 1.886 1.076 0.570 5 57.05 2.44 DC 12 V 1M Bits/s, 37 Packet 0.625 0.393 0.629 2 62.92 2.01 2M Bits/s, 37 Packet 0.625 0.207 0.330 8 33.08 4.80 1M Bits/s, 255 Packet 2.499 2.135 0.854 3 85.43 0.68 2M Bits/s, 255 Packet 1.873 1.076 0.574 5 57.45 2.41 Notes. 1. Duty cycle (Linear) = Ton time / Period 2. DCF…

Text truncated - open the document above for the full version.

verify No.401014338638 KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR21-SRF0011-A Page (2 ) of (105) KCTL-TIR001-003/3 KP20-05065 REPORT REVISION HISTORY Date Revision Page No 2021-01-14 Originally issued - 2021-01-21 Updated 4 This report shall not be reproduced except in full, without the written approval of KCTL Inc. This document may be altered or revised by KCTL Inc. personnel only, and shall be noted in the revision section of the document. Any alteration of this document not carried out by KCTL Inc. will constitute fraud and shall nullify the document. This test report is a general report that does not use the KOLAS accreditation mark and is not related to KS Q ISO/IEC 17025 and KOLAS accreditation. Note. The report No. KR21-SRF0011 is superseded by the report No. KR21-SRF0011-A. General remarks for test reports Nothing significant to report. KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8…

Text truncated - open the document above for the full version.