A3LEJFT810Bluetooth Keyboard

Printed in Korea GH68-44138A Rev.1.0 E Type 04/2015 QUICK START GUIDE EJ-FT810 Galaxy Tab S2 BOOK COVER KEYBOARD 3 Charging the battery Before using the keyboard for the first time, you must charge the battery. Connect the keyboard to a charger. • Chargers are sold separately. • The charger should remain close to the electric socket and easily accessible while charging. • The socket-outlet shall be installed near the equipment and shall be easily accessible. Turning the keyboard on and off Slide the Power switch to turn on or off the keyboard. When you turn on the keyboard for the first time, it automatically enters Bluetooth pairing mode. Connecting devices via Bluetooth 1. Turn on the keyboard, and then press and hold the (F11 or F12) key for about three seconds to enter Bluetooth pairing mode. The notification light will flash red, green, and blue. 2. On your other device, activate the Bluetooth feature and tap Samsung Tab S2 Keyboard from the list of available devices. 3. On the keyboard, enter the passkey displayed on your other device’s screen and press the Enter key. The keyboard can pair with up to two Bluetooth-enabled devices and you can easily switch connections between the paired devices. For more information, refer to the user manual. 4 Using the cover Attach the cover to your tablet and use it as a stand. 1. Open the cover. 2. Align and connect the cover’s push clips to the push clips on the back of your tablet. 3. Fold the back of the cover into a triangular shape. Then, stand the tablet in landscape orientation. 4. Place the keyboard on the front of the cover as shown in the image. ► 1 Safety information Read all safety information before using the device to ensure safe and proper use. To view the full safety information, refer to the Samsung website. The device contains magnets. The American Heart Association (US) and the Medicines and Healthcare Products Regulatory Agency (UK) both warn that magnets can affect the operation of implanted pacemakers, cardioverters, defibrillators, insulin pumps or other electro medical devices (collectively, “Medical Device”) within the range of 15 cm (6 inches). If you are a user of any of these Medical Devices, DO NOT USE THIS DEVICE UNLESS YOU HAVE CONSULTED WITH YOUR PHYSICIAN Use manufacturer-approved batteries, chargers, accessories, and supplies Do not touch the device with wet hands Do not drop or cause an impact to the charger or the device Do not store your device in very hot or very cold areas. It is recommended to use your device at temperatures from 5°C to 35°C Prevent the multipurpose jack and the small end of the charger from contact with conductive materials, such as liquids, dust, metal powders, and pencil leads Do not allow children or animals to chew or suck the device Do not disassemble, modify, or repair your device 2 a b c d 1 Copyright © 2015 Samsung Electronics Bluetooth ® is a registered trademark of Bluetooth SIG, Inc. worldwide. • Please read this manual before using the device to ensure safe and proper use. • Images may differ in appearance from the actual product. Content is subject to change without prior notice. You can access the full user manual for more information. Visit www.samsung.com to view device information, the user manual, and more. Device layout Power switchCaps Lock indicator light Charging portNotification light 5 Correct disposal This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste. This product is RoHS compliant. This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste. Removing the battery • To remove the battery, you must visit an authorised service centre with the provided instructions. • For your safety, you must not attempt to remove the battery. If the battery is not properly removed, it may lead to damage to the battery and device, cause personal injury, and/or result in the device being unsafe. • Samsung does not accept liability for any damage or loss (whether in contract or tort, including negligence) which may arise from failure to precisely follow these warnings and instructions, other than death or personal injury caused by Samsung’s negligence. 1. T urn the keyboard over and remove four rubber feet. 2. Loosen and remove the four screws. 3. Use a flat-edged tool between the keyboard and back cover to pry them apart. 4. Gently lever the battery away from the main body of the unit. 5. U se a nipper to cut the connections between the battery and the circuit board. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the user's authority to operate the equipment. This device complies with Industry Canada licence- exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

129, Samsung‐Ro, Yeongtong‐Gu, Suwon‐City Gyeonggi‐Do, 443‐742, Korea May 12, 2015 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 LETTER OF AUTHORIZATION To whom it may concern: I, the undersigned, hereby authorize Lab Manager Hyunchae, You (or Logan, Lee) and of SGS Korea Co., Ltd. and hereafter referred to as SGS Korea, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Lab Manager Hyunchae, You (or Logan. Lee) of SGS Korea Co., Ltd. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti‐Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing SGS Korea as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; 129, Samsung‐Ro, Yeongtong‐Gu, Suwo n‐City Gyeonggi‐Do, 443‐742, Korea i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours Chan Ho, Youn / General Manager Samsung Electronics North America INC. TEL: +1-973-808-6362 E-mail: [email protected]

129, Samsun g‐Ro, Yeongtong‐Gu, Suwon‐City Gyeonggi‐Do, 443‐742, Korea May 12, 2015 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 REQUEST OF CONFIDENTIALITY for FCC ID: A3LEJFT810 To Whom It May Concern: Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, Samsung Electronics Co., Ltd. hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short‐Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04‐1705. This provision will give Samsung Electronics Co., Ltd temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Temporary Confidential exhibits are listed as follows: CONFIDENTIAL LIST Permanent 1 Block Diagram 2 Operational Descriptions 3 Schematics Short‐Term 4 External Photos 5 Internal Photos 6 Test‐Setup Photos 7 User Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Sincerely Yours, Chan Ho, Youn / General Manager Samsung Electronics North America INC. TEL: +1-973-808-6362 E-mail: [email protected]

Model :EJ-FT810 External photos of EUT Model :EJ-FT810 Top view of EUT Bottom view of EUT Model :EJ-FT810 Side view of EUT Model :EJ-FT810 Front view of EUT Back view of EUT

Label Information FCC ID: A3LEJFT810 IC: 649E-EJFT810 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. MODEL: EJ-FT810 FCC ID: A3LEJFT810 IC: 649E-EJFT810

Model :EJ-FT810 Internal photos of EUT Model :EJ-FT810 Top view of EUT Model :EJ-FT810 Top view of Main PCB Bottom view of Main PCB Model :EJ-FT810 Antenna PCB Antenna

SGS Korea Co., Ltd. 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, 435-040 Tel. 031-428-5700 / Fax. 031-427-2371 http://www.sgsgroup.kr Page : 1 / 2 Date of Issue : 2015-05-21 FCC ID: A3LEJFT810 1. Standalone SAR test exclusion threshold Per FCC KDB 447498 D01v05r02, the SAR exclusion threshold for distances < 50㎜ is defined by the following equation: Frequency = 2 480 ㎒ Test. Separation Distances = 5 mm Maximum Tune-up Tolerances = 6 dBm Bluetooth Mode Calculation value: 4 (㎽) / 5(mm) x √ 2.480 = 1.26 So, Calculation value ≤ 3.0 Bluetooth Mode Conclusion: Standalone SAR is not required 2. Simultaneous transmission SAR test exclusion threshold 2.1 Estimated SAR Evaluation Analysis When standalone SAR is not required to be measured per FCC KDB 447498 D01v05r02 4.3.2.2), the following equation must be used to estimate the standalone 1g SAR for simultaneous transmission involving that transmitter. Mode Frequency Maximum Allowed Power Separation Distance Estimated SAR [MHz] [mW] [mm] [W/kg] Bluetooth 2480 4 5 0.168 2.2 SPLSR Evaluation Analysis EUT Pair Worst case 1g SAR (W/kg) Estimated 1g SAR (W/kg) 1g SAR Sum (W/kg) Separation Distance (mm) SPLS Ratio SPLS Ratio Limit "a" "b" a b a + b Worst D a-b (a+b) 1.5 / D a-b ≤ 0.04 Tablet PC Keyboard B.T 1.6 0.168 1.768 175.43 0.01 2.3 Simultaneous Transmission conclusion The above numerical summed SAR results and SPLSR analysis is sufficient to determine that simultaneous transmission cases will not exceed the SAR limit and therefore no measured volumetric simultaneous SAR summation is required per FCC KDB publication 447498 D01 v05r02. SGS Korea Co., Ltd. 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, 435-040 Tel. 031-428-5700 / Fax. 031-427-2371 http://www.sgsgroup.kr Page : 2 / 2 Date of Issue : 2015-05-21 2.4 Simultaneous Transmission Separation Distances Worst distances of Tablet PC and Keyboard Antenna

Report Number : F690501/RF-RTL008715-1 Page: 2 of 37 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) INDEX Table of Contents Page 1. General Information --------------------------------------------------------------------------------- 3 2. Radiated Spurious Emissions and Conducted Spurious Emission---------------------- 6 3. 6㏈ Bandwidth -------------------------------------------------------------------------------------- 23 4. Maximum Conducted output power ------------------------------------------------------------- 26 5. Power Spectral Density ---------------------------------------------------------------------------- 29 6. AC Power Line Conducted Emission ----------------------------------------------------------- 32 7. Antenna Requirement ------------------------------------------------------------------------------ 37 Report Number : F690501/RF-RTL008715-1 Page: 3 of 37 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 1. General Information 1.1. Testing Laboratory SGS Korea Co., Ltd. (Gunpo Laboratory) - Wireless Div. 2FL, 10-2, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-837 All SGS services are rendered in accordance with the applicable SGS conditions of service available on request and accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx. Phone No. : + 82 31 688 0901 Fax No. : + 82 31 688 0921 1.2. Details of Applicant Applicant : Samsung Electronics Co., Ltd. Address : 129, Samsung-ro, Yeongtong-gu Suwon-si, Gyeonggi-do, 443-742 Korea, Republic of Contact Person : Cho, Ha-Yeon Phone No. : +82 31 301 5071 1.3. Description of EUT Kind of Product Bluetooth Keyboard Model Name EJ-FT810 Power Supply DC 3.7 V Frequency Range 2 402 ㎒ ~ 2 480 ㎒ (BT LE) Modulation Technique DSSS Number of Channels 40 channel (BT LE) Antenna Type Internal type Antenna Gain -0.61 ㏈i Report Number : F690501/RF-RTL008715-1 Page: 4 of 37 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 1.4. Test Equipment List Equipment Manufacturer Model S/N Cal Date Cal Interval Cal Due. Signal Generator Agilent E8257D MY51501169 Jul. 17, 2014 Annual Jul. 17, 2015 Spectrum Analyzer Agilent N9030A MY53120526 Jul. 17, 2014 Annual Jul. 17, 2015 Spectrum Analyzer R&S FSV30 103102 Jul. 16, 2014 Annual Jul. 16, 2015 High Pass Filter Wainwright WHK3.0/18G-6SS 4 Jul. 02, 2014 Annual Jul. 02, 2015 High Pass Filter Wainwright WHK7.5/26.5G-6SS 15 Jul. 02, 2014 Annual Jul. 02, 2015 Low Pass Filter Mini circuits NLP-1200+ V 8979400903-2 Mar. 12, 2015 Annual Mar. 12, 2016 Power Sensor R&S NRP-Z81 100669 Mar. 12, 2015 Annual Mar. 12, 2016 Bluetooth Tester TESCOM TC-3000C 3000C000142 Dec. 11, 2014 Annual Dec. 11, 2015 Directional Coupler KRYTAR 152613 122661 Mar. 16, 2015 Annual Mar. 16, 2016 DC Power Supply Agilent U8002A MY49030063 Dec. 06, 2014 Annual Dec. 06, 2015 Preamplifier H.P. 8447F 2944A03909 Aug. 27, 2014 Annual Aug. 27, 2015 Preamplifier MITEQ Inc. SCU-18 10117 Sep. 26, 2014 Annual Apr. 10, 2016 Preamplifier MITEQ Inc. JS44-18004000-35-8P 1546891 Apr. 10, 2015 Annual Apr. 10, 2016 Bilog Antenna SCHWARZBECK MESSELEKTRONIK VULB9163 396 Jun. 07, 2013 Biennial Jun. 07, 2015 Loop Antenna SCHWARZBECK MESSELEKTRONIK FMZB 1519 1519-039 Jul. 09, 2013 Biennial Jul. 09, 2015 Horn Antenna SCHWARZBECK MESSELEKTRONIK HF906 100326 May 09, 2014 Biennial Apr. 16, 2016 Horn Antenna SCHWARZBECK MESSELEKTRONIK BBHA9170 BBHA9170431 May 15, 2014 Biennial May 15, 2016 Antenna Master INN-CO MM4000 N/A N/A N/A N.C.R. Turn Table INN-CO DS 1200 S N/A N/A N/A N.C.R. Test Receiver R&S ESU26 100368 Dec. 16, 2014 Annual Dec. 16, 2015 Test Receiver R&S ESCI 7 100911 Dec. 24, 2014 Annual Dec. 24, 2015 Two-Line V-Network R&S ENV216 100190 Dec. 25, 2014 Annual Dec. 25, 2015 Anechoic Chamber SY Corporation L × W × H (9.6 m × 6.4 m × 6.6 m) N/A N/A N/A N.C.R. Shield Room SY Corporation L × W × H (6.5 m × 3.5 m × 3.5 m) N/A N.C.R. N/A N.C.R. Report Number : F690501/RF-RTL008715-1 Page: 5 of 37 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 1.5. Summary of Test Results The EUT has been tested according to the following specifications: APPLIED STANDARD : FCC Part15 Subpart C Standard section Test Item(s) Result 15.205 15.209 15.247(d) Radiated Spurious Emissions and Conducted Spurious Emission Complied 15.247(a)(2) 6 ㏈ Bandwidth Complied 15.247(b)(3) Maximum Conducted Output Power Complied 15.247(e) Power Spectral Density Complied 15.207 AC Power Line Conducted Emission Complied 1.6. Test Procedure(s) The measurement procedures described in the American National Standard for Methods of Measurement of Radio-Noise Emissi…

Text truncated - open the document above for the full version.

Test setup photos of EUT A. Photo of Radiated Spurious Emission Test (Below 1㎓) B. Photo of Radiated Spurious Emission Test (Above 1㎓) C. Photos of AC Power line emission test