A3LEJPT870Stylus Pen

English Copyright © 2020 Samsung Electronics America, Inc. Bluetooth ® is a registered trademark of Bluetooth SIG, Inc. worldwide. Other marks are the property of their respective owners. • Please read this guide before using the device to ensure safe and proper use. • Before using the S Pen, make sure it is compatible with your device. • Your consumer rights are governed by the law of the country in which you purchased the product. Please contact your service provider for more information. Using the S Pen Use the S Pen to perform touch actions or draw on the screen of your mobile device. You can use additional features by pressing the S Pen button ( ). When you attach the S Pen on the rear of your mobile device, charging will start. Refer to the mobile device’s user manual for more information. Safety information Read all safety information before using the device to ensure safe and proper use. To view the full safety information, refer to the Samsung website. Use only charging devices and batteries approved by Samsung. Samsung accessories are designed for your device to maximize battery life. Using other accessories may invalidate your warranty and may cause damage Do not touch the device with wet hands Do not drop or cause an impact to the charger or the device Do not allow children or animals to chew or suck the device Do not disassemble, modify, or repair your device FCC 15.21 Warning against unauthorized change Pursuant to Part 15.21 of the FCC Rules, you are cautioned that changes or modifications not expressly approved by Samsung could void your authority to operate the device. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • Depending on the region or model, some devices are required to receive approval from the Federal Communications Commission (FCC). If your device is approved by the FCC, you can view the FCC ID of the device. To view the FCC ID, launch the Settings app and tap About phone → Status. Samsung Mobile Products and Recycling Samsung cares for the environment and encourages its customers to properly dispose of Devices and Samsung accessories in accordance with local regulations. In some areas, disposal of these items in household or business trash may be prohibited. Dispose of other unwanted electronics through an approved recycler. To find the nearest recycling location, go to our website: www.samsung.com/recyclingdirect or call 1-877-278-0799. Samsung Electronics America, Inc 85 Challenger Road, Ridgefield Park, New Jersey, 07660 Phone: 1-800-SAMSUNG (726-7864) Printed in Korea A00000 Rev.1.0 USA Type 06/2020 QUICK START GUIDE EJ-PT870 S Pen b a Device layout S Pen buttonS Pen nib English Copyright © 2020 Samsung Electronics Bluetooth ® is a registered trademark of Bluetooth SIG, Inc. worldwide. • Please read this guide before using the device to ensure safe and proper use. • Before using the S Pen, make sure it is compatible with your device. • Your consumer rights are governed by the law of the country in which you purchased the product. Please contact your service provider for more information. Device layout Using the S Pen Use the S Pen to perform touch actions or draw on the screen of your mobile device. You can use additional features by pressing the S Pen button. When you attach the S Pen on the rear of your mobile device, charging will start. Refer to the mobile device’s user manual for more information. Safety information Read all safety information before using the device to ensure safe and proper use. To view the full safety information, refer to the Samsung website. Use manufacturer-approved batteries, chargers, accessories, and supplies Do not touch the device with wet hands Do not drop or cause an impact to the charger or the device Do not allow children or animals to chew or suck the device Do not disassemble, modify, or repair your device FCC 15.21 Warning against unauthorized change Pursuant to Part 15.21 of the FCC Rules, you are cautioned that changes or modifications not expressly approved by Samsung could void your authority to operate the device. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • Depending on the region or model, some devices are required to receive approval from the Federal Communications Commission (FCC). If your device is approved by the FCC, you can view the FCC ID of the device. To view the FCC ID, launch the Settings app and tap About phone → Status. RSS-Gen, Section 8.4 Statement IC Notice This device complies with Industry Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. • Depending on the region or model, some devices are required to receive approval from Innovation, Science and Economic Development Canada (ISED)/the Federal Communications Commission (FCC). If your device is approved by the ISED/FCC, you can view the ISED/FCC ID of the device. To view the ISED/FCC ID, launch the Settings app and tap About phone → Status. Printed in Korea A00000 Rev.1.0 CANADA Type 06/2020 QUICK START GUIDE EJ-PT870 b a S Pen buttonS Pen nib Présentation de l’appareil Bouton du S Pen Pointe du S Pen Utilisation du S Pen Utilisez le S Pen pour toucher l’écran tactile ou pour dessiner sur l’écran de votre appareil mobile. Vous pouvez utiliser d’autres fonctionnalités en appuyant sur le bouton S Pen. Lorsque vous fixez le S Pen dans l’emplacement du S Pen de votre appareil mobile, le charg…

Text truncated - open the document above for the full version.

SAMSUNG ELECTRONICS CO., LTD 129, Samsung-ro,Yeongtong-gu Suwon-si,Gyeonggi-do, 16677, Korea June 12 th , 2020 Federal Communications Commission SUBJECT : Label Statement FCC ID : A3LEJPT870 To Whom It May Concern: We hereby provide the following attestations according to 47 CFR 2.935 and FCC KDB 784748 D02: This device operates in conjunction with a device that has an electric display and therefore qualifies for e-labling per 47 CFR 2.935 and FCC KDB 784748 D02. The product and associated device are capable of functioning locally and under control of the end-user, per FCC KDB 784748 D02. At the time of purchase, the FCC ID is readily and physically visible to the purchaser on the exterior package per 2.935(d). The FCC ID will be readily legible without the aid of magnification according to 2.935(a). The literature in the package describes how to access the electronic display to find the FCC ID per 2.93 5(e) and FCC KDB 784748. The user will be able to access this information within a maximum of 3 steps. We, Samsung have programmed the e-label and it is not able to be modified by any third party.The user will be able to access this information without a SIM card, s pecial accessories or supplemental plug- ins. The FCC ID will be able to survive normal shipping and handling so it is visible for inspection at the time of import. Should you have any questions or comments concerning the above, please contact the undersigned. Sincerely Yours, JENNI, CHUN General Manager Samsung Electronics CO. LTD TEL: +1-973-808-6375 FAX: +1-973-808-6361 E-mail: [email protected]

Samsung Electronics Co., LTD. 129, Samsu ng -ro , Yeongtong-gu Suwon-City, Gyeonggi-do, 16677, Korea Date: June 16, 2020 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. UL Verification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize Ms. Athena Kim/Assistant manager of KCTL Inc. and hereafter referred to as KCTL to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Ms. Athena Kim/Assistant manager of KCTL Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing KCTL as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Jenni Chun, General Manager Regulatory & Environmental Affairs Samsung Electronics America, Inc

Samsung Electronics Co., LTD. 129, Samsung -ro , Yeongtong-gu Suwon-City, Gyeonggi-do, 16677, Korea CONFIDENTIALITY REQUEST Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 June 16, 2020 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, Samsung Electronics Co., Ltd. requests confidentiality for the following products: FCC ID Number Product Title/Model A3LEJPT870 Stylus Pen / EJ-PT870 The following exhibits contain trade secrets and proprietary information that could be of benefit to our competitors regarding the design of our product. This material is not customarily available to the general public and we request that it be withheld from public inspection. We request that the following information submitted be held permanent confidential treatment. Permanent Confidential Request -. Schematics -. Block Diagram -. Operational Description -. Antenna specification -. Parts list -. Tune-up procedure We hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give temporary confidentiality of commercially sensitive information prior to product release. Short-Term Confidential Request -. External Photos -. Internal Photos -. Test set-up photo -. User Manual If you have any questions, please feel free to contact me at the address shown below. Sincerely, Jenni Chun/ General manager

http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval External photos of EUT http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval

Description of E-label on the A3LEJPT870 June 15 th , 2020 IC: 649E-EJPT870 HVIN: EJ-PT870 FCC ID: A3LEJPT870 This model is applied E-label, please find description of E-label below. 1.ISED( E-label) - English: Settings > About phone> Status ISED( E-label) - French: Paramètres > À propos du téléphone> État S Pen FCC and ISED certification FCC ID: A3LEJPT870 IC: 649E-EJPT870 (EJ-PT870) 2.Instruction of E-label on the User manual (online manual) •Depending on the region or model, some devices are required to receive approval from Innovation, Science and Economic Development Canada (ISED)/the Federal Communications Commission (FCC). If your device is approved by the ISED/FCC, you can view the ISED/FCC ID of the device. To view the ISED/FCC ID, launch the Settings app and tap About phone → Status. •Selon la région ou le modèle, certains appareils doivent recevoir une certification de Innovation, Sciences et Développement économique Canada (ISDE) et de la Commission fédérale des communications (FCC). Si votre appareil est approuvé par ISDE/FCC, vous pouvez trouver l’ID ISDE/FCC de l’appareil. Pour ce faire, ouvrez l’appli Paramètres et touchez À propos du téléphone → État. <Display Screen>

http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval Internal photos of EUT http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval PEA Antenna (BLE) http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval

http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval * RF Exposure 1. Regulation 1-1. FCC According to the KDB 447498 D01 V06, the following RF exposure evaluation shall to demonstrate RF exposure compliance. Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition(s), listed below, is (are) satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions. The minimum test separation distance defined in 4.1 f) is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander. To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified, typically in the SAR measurement or SAR analysis report, by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting are required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions; for example, handheld PTT two-way radios, handsets, laptops and tablets, etc. a) For 100 ㎒ to 6 ㎓ and test separation distances ≤ 50 ㎜, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, ㎽) / (min. test separation distance, ㎜)] · [√f(㎓)] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extremity SAR,30 where ● f(㎓) is the RF channel transmit frequency in ㎓ ● Power and distance are rounded to the nearest ㎽ and mm before calculation ● The result is rounded to one decimal place for comparison ● The values 3.0 and 7.5 are referred to as numeric thresholds in step b) below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 ㎜, and for transmission frequencies between 100 ㎒ and 6 ㎓. When the minimum test separation distance is < 5 ㎜, a distance of 5 ㎜ according to 4.1 f) is applied to determine SAR test exclusion. b) For 100 ㎒ to 6 ㎓ and test separation distances > 50 ㎜, the 1-g and 10-g SAR test exclusion thresholds are determined by the following (also illustrated in Appendix B): 1) {[Power allowed at numeric threshold for 50 ㎜ in step a)] + [(test separation distance – 50 ㎜)·(f(㎒)/150)]} ㎽, for 100 ㎒ to 1500 ㎒ 2) {[Power allowed at numeric threshold for 50 ㎜ in step a)] + [(test separation distance – 50 ㎜)·10]} ㎽, for > 1500 ㎒ and ≤ 6 ㎓ http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval c) For frequencies below 100 ㎒, the following may be considered for SAR test exclusion (also illustrated in Appendix C): 1) For test separation distances > 50 ㎜ and < 200 ㎜, the power threshold at the corresponding test separation distance at 100 ㎒ in step b) is multiplied by [1 + log(100/f(㎒))] 2) For test separation distances ≤ 50 ㎜, the power threshold determined by the equation in c) 1) for 50 ㎜ and 100 ㎒ is multiplied by ½ 3) SAR measurement procedures are not established below 100 ㎒. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any SAR test results below 100 ㎒ to be acceptable. http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval 1-2. IC According to RSS-102 Issue 5 SAR evaluation is required if the separation distance between the user and/or bystander and the antenna and/or radiating element of the device is less than or equal to 20 cm, except when the device operates at or below the applicable output power level (adjusted for tune-up tolerance) for the specified separation distance defined in Table 1. Output power level shall be the higher of the maximum conducted or equivalent isotropically radiated power (e.i.r.p.) source-based, time-averaged output power. For test separation distance less than 5mm, the exemption limits for a separation distance of 5 mm can be applied to determine if a routine evaluation is required. Table 1: SAR evaluation – Exemption limits for routine evaluation based on frequency and separation distance Frequency (㎒) Exemption Limits (㎽) At seperation distance of ≤5 ㎜ At seperation distance of 10 ㎜ At seperation distance of 15 ㎜ At seperation distance of 20 ㎜ At seperation distance of 25 ㎜ ≤300 71 ㎽ 101 ㎽ 132 ㎽ 162 ㎽ 193 ㎽ 450 52 ㎽ 70 ㎽ 88 ㎽ 106 ㎽ 123 ㎽ 835 17 ㎽ 30 ㎽ 42 ㎽ 55 ㎽ 67 ㎽ 1 900 7 ㎽ 10 ㎽ 18 ㎽ 34 ㎽ 60 ㎽ 2 450 4 ㎽ 7 ㎽ 15 ㎽ 30 ㎽ 52 ㎽ 3 500 2 ㎽ 6 ㎽ 16 ㎽ 32 ㎽ 55 ㎽ 5 800 1 ㎽ 6 ㎽ 15 ㎽ 27 ㎽ 41 ㎽ Frequency (㎒) Exemption Limits (㎽) At seperation distance of 30 ㎜ At seperation distance of 35 ㎜ At seperation distance of 40 ㎜ At seperation distance of 45 ㎜ At seperation distance of ≥50 ㎜ ≤300 223 ㎽ 254 ㎽ 284 ㎽ 315 ㎽ 345 ㎽ 450 141 ㎽ 159 ㎽ 177 ㎽ 195 ㎽ 213 ㎽ 835 80 ㎽ 92 ㎽ 105 ㎽ 117 ㎽ 130 ㎽ 1 900 99 ㎽ 153 ㎽ 225 ㎽ 316 ㎽ 431 ㎽ 2 450 83 ㎽ 123 ㎽ 173 ㎽ 235 ㎽ 309 ㎽ 3 500 86 ㎽ 124 ㎽ 170 ㎽ 225 ㎽ 290 ㎽ 5 800 56 ㎽ 71 ㎽ 85 ㎽ 97 ㎽ 106 ㎽ http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval 2. Result 2-1. Calculation Result of RF Exposure (FCC) Mode Test frequency [㎒] Max. tune-up Power [㏈…

Text truncated - open the document above for the full version.

verify No.943066836591 KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR20-SRF0143 Page (2) of (34) KCTL-TIR001-003/3 KP20-02544 REPORT REVISION HISTORY Date Revision Page No 2020-06-16 Originally issued - This report shall not be reproduced except in full, without the written approval of KCTL Inc. This document may be altered or revised by KCTL Inc. personnel only, and shall be noted in the revision section of the document. Any alteration of this document not carried out by KCTL Inc. will constitute fraud and shall nullify the document. This test report is a general report that does not use the KOLAS accreditation mark and is not related to KS Q ISO/IEC 17025 and KOLAS accreditation. General remarks for test reports Nothing significant to report. KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR20-SRF0143 Page (3) of (34) This test report shall not be reproduced, except in full, without the written approval KCTL-TIR001-003/3 KP20-02544 CONTENTS 1. General information ...................................................................................................... 4 2. Device information ........................................................................................................ 4 2.1. Accessory information ............................................................................................ 4 2.2. Frequency/channel operations ................................................................................ 5 2.3. Duty Cycle Factor ................................................................................................... 5 3. Antenna requirement .................................................................................................... 6 4. Summary of tests .......................................................................................................... 7 5. Measurement uncertainty ............................................................................................. 8 6. Measurement results explanation example .................................................................. 9 7. Test results ................................................................................................................. 10 7.1. Maximum peak output power ................................................................................ 10 7.2. Peak Power Spectral Density ............................................................................... 13 7.3. 6 dB Bandwidth(DTS Channel Bandwidth) ........................................................... 15 7.4. Spurious Emission, Band Edge and Restricted bands .......................................... 18 7.5. Conducted Spurious Emission .............................................................................. 32 8. Measurement equipment ............................................................................................ 34 KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR20-SRF0143 Page (4) of (34) This test report shall not be reproduced, except in full, without the written approval KCTL-TIR001-003/3 KP20-02544 1. General information Client : Samsung Electronics Co., Ltd. Address : 129, Samsung-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Rep. of Korea Manufacturer : Samsung Electronics Co., Ltd. Address : 129, Samsung-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Rep. of Korea Laboratory : KCTL Inc. Address : 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea Accreditations : FCC Site Designation No: KR0040, FCC Site Registration No: 687132 VCCI Registration No. : R-20080, G-20078, C-20059, T-20056 Industry Canada Registration No. : 8035A KOLAS No.: KT231 2. Device information Equipment under test : Stylus Pen Model : EJ-PT870 Modulation technique : GFSK Number of channels : 40 ch Power source : DC 2.75 V Antenna specification : PEA Antenna Antenna gain : -3.33 ㏈i Frequency range : 2 402 ㎒ ~ 2 480 ㎒ Software version : sw 0x22 Hardware version : BLE 6-2 Test device serial No. : N/A Operation temperature : 5 °C ~ 40 °C 2.1. Accessory information Equipment Manufacturer Model Serial No. Power source FCC ID & IC N/A - - - - - KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR20-SRF0143 Page (5) of (34) This test report shall not be reproduced, except in full, without the written approval KCTL-TIR001-003/3 KP20-02544 2.2. Frequency/channel operations This device contains the following capabilities: Bluetooth Low Energy Ch. Frequency (㎒) 00 2 402 . . . . 19 2 440 . . . . 39 2 480 Table 2.2.1. Bluetooth Low Energy 2.3. Duty Cycle Factor Test mode Period (ms) On time (ms) Duty cycle Duty Cycle Factor (dB) (Linear) (%) 1M Bits/s, 37 Packet 0.625 2 0.390 0 0.623 8 62.38 2.05 Notes. 1. Duty cycle (Linear) = Ton time / Period 2. DCF(Duty cycle factor) = 10log(1/duty cycle) 1M Bits/s, 37 Packet KCTL Inc. 65, Sinwon-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea TEL: 82-31-285-0894 FAX: 82-505-299-8311 www.kctl.co.kr Report No.: KR20-SRF0143 Page (6) of (34) This test report shall not be reproduced, except in full, without the written approval KCTL-TIR001-003/3 KP20-02544 3. Antenna requirement Requirement of FCC part section 15.203: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. Requirement of RSS-Gen Section 6.8: The applicant for equipment certification shall provide a list of all antenna types that may…

Text truncated - open the document above for the full version.

http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval Test setup photos - Below 30 ㎒ (9 ㎑ ~ 30 ㎒) - Below 1 ㎓ (30 ㎒ ~ 1 ㎓) http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval - Above 1 ㎓ (1 ㎓ ~ 18 ㎓) - Above 18 ㎓ (18 ㎓ ~ 26.5 ㎓)