A3LEPPN920WIRELESS CHARGER

QUICK START GUIDE Wireless charger Printed in Korea GH68-44694A Rev.1.0 E Type 07/2015 2 a b c d 1 Copyright © 2015 Samsung Electronics • Please read this guide before using the device to ensure safe and proper use. • Images may differ in appearance from the actual product. Content is subject to change without prior notice. You can access the full user manual for more information. Visit www.samsung.com to view device information, the user manual, and more. 3 Device layout Wireless charging surface Indicator light Charger portFan vent Wireless charging covers and chargers are sold separately. Using the wireless charger 1. Connect the charger to the wireless charger. Then, place a supported mobile device in the centre of the charging surface. ( 1 ) 2. When the mobile device is fully charged, remove the mobile device from the wireless charger. Use only Samsung-approved chargers (5 V/ 2 A, 5.3 V/2 A, and 9 V/1.67 A). • The charger should remain close to the electric socket and easily accessible while charging. • The socket-outlet shall be installed near the equipment and shall be easily accessible. • If you use the wireless charger in areas with weak network signals, you may lose network reception. 4 Wireless fast charging To begin fast charging, place a mobile device that supports wireless fast charging on the wireless charger. For more information, refer to the user manual. To use this feature, you must connect the wireless charger to a charger that supports Adaptive Fast Charging (AFC). Safety information Read all safety information before using the device to ensure safe and proper use. To view the full safety information, refer to the Samsung website. Use manufacturer-approved batteries, chargers, accessories, and supplies Do not touch the device with wet hands Do not drop or cause an impact to the charger or the device The device can be used in locations with an ambient temperature of 0°C to 35°C. You can store the device at an ambient temperature of -20°C to 50°C. Using or storing the device outside of the recommended temperature ranges may damage the device or reduce the battery’s lifespan 5 Prevent the multipurpose jack and the small end of the charger from contact with conductive materials, such as liquids, dust, metal powders, and pencil leads Do not allow children or animals to chew or suck the device Do not disassemble, modify, or repair your device Magnetic stripe cards, including credit cards, phone cards, passbooks, and boarding passes, may be damaged by magnetic fields Correct disposal This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste. This product is RoHS compliant. 6 FCC Warning Statement FCC Part 15.19 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Part 15.21 Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

July 21, 2015 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 REQUEST OF CONFIDENTIALITY FOR FCC ID: A3LEPPE920 To Whom It May Concern: Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, Samsung Electronics Co., Ltd. hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short‐Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04‐1705. This provision will give Samsung Electronics Co., Ltd temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Temporary Confidential exhibits are listed as follows: CONFIDENTIAL LIST Permanent 1 Block Diagram 2 Operational Descriptions 3 Schematics Short‐Term 4 External Photos 5 Internal Photos 6 Test‐Setup Photos 7 User Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Sincerely Yours, Chan Ho, Youn / General Manager Samsung Electronics North America INC. TEL: +1-973-808-6362 E-mail: [email protected] 19 Chapin Rd., Building D, Pine Brook, N ew Jersey, 07058, United States

External photos of EUT Front view of EUT Rear view of EUT Top view of EUT Bottom view of EUT Side view of EUT

WIRELESS CHARGER MODEL : EP-PN920 INPUT : 5.0 V 2.0 A 9.0 V 1.67 S/N : SAMSUNG, YATELEY, GU46 6GC.UK FCC ID: A3LEPPN920 : A MADE IN VIETNAM / FABRIQUÉ AU VIETNAM Rear view of EUT Label Format and Location FCC ID: A3LEPPN920

Internal photos of EUT Internal view of EUT Loop Coil Antenna Top view of main board Bottom view of main board

Report Number : F690501/RF-RTL008943-1 Page: 2 of 11 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) INDEX TABLE OF CONTENTS Page 1. General Information ----------------------------------------------------------------------- 3 2. Test Result ----------------------------------------------------------------------------------- 5 Report Number : F690501/RF-RTL008943-1 Page: 3 of 11 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 1. General information 1.1. Testing laboratory SGS Korea Co., Ltd. (Gunpo Laboratory) - Wireless Div. 2FL, 10-2, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-837 All SGS services are rendered in accordance with the applicable SGS conditions of service available on request and accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx. Phone No. : +82 31 688 0901 Fax No. : +82 31 688 0921 1.2. Details of applicant Applicant : Samsung Electronics Co., Ltd. Address : 129, Samsung-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, Republic of Korea Contact Person : Kim, Kyung-Won Phone No. : +82 31 301 0274 1.3. Description of EUT Kind of Product WIRELESS CHARGER Model Name EP-PN920 Power Supply DC 5 V, DC 9 V (Used AC 100 V ~ 240 V adaptor) Frequency Range 110 ㎑ ~ 190 ㎑ Operating Conditions -20 °C ~ 60 °C Antenna Type Inductive loop coil antenna 1.4. Declarations by the manufacturer - Operation temperature : -20 °C ~ 60 °C Report Number : F690501/RF-RTL008943-1 Page: 4 of 11 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 1.5. Test Equipment List Equipment Manufacturer Model S/N Cal Date Cal Interval Cal Due. Spectrum Analyzer R&S FSV30 103210 Dec. 29, 2014 Annual Dec. 29, 2015 Loop Antenna R&S HFH2-Z2 100118 Jun. 04, 2015 Biennial Jun. 04, 2017 E-Field Probe ETS-LINDGREN HI-6005 00047870 Mar. 11, 2015 Annual Mar. 11, 2016 B-Field Probe Narda BN 2300/90.10 J-0025 Jan. 23, 2015 Annual Jan. 23, 2016 Exposure Level Meter Narda ELT-400 J-0015 Jan. 23, 2015 Annual Jan. 23, 2016 Anechoic Chamber SY Corporation L × W × H (9.6 m × 6.4 m × 6.6 m) N/A N.C.R. N/A N.C.R. 1.6. Test report revision Revision Report number Date of Issue Description 0 F690501/RF-RTL008943 2015.07.20 Initial 1 F690501/RF-RTL008943-1 2015.07.22 Added data for the E-field and H-field at the bottom position 1.7. Worst case of test configurations In order to check all kinds of possible configurations, EUT was evaluated with appropriate client and under each charging condition as below table. EUT configuration Description Charging Mode with client device Less than 1 % of battery Less than 50 % of battery 100 % full charging of battery Report Number : F690501/RF-RTL008943-1 Page: 5 of 11 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 2. Test Result 2.1. Test Setup 2.2. Measurement procedure a) The RF exposure test was performed on 360 degree turn table in anechoic chamber. b) The measurement probe was placed at test distance (10 ㎝) which is between the edge of the charger and the geometric center of probe. c) The turn table was rotated 360 degree to search of highest strength d) The highest emission level was recorded and compared with limit as soon as measurement of each points (A, B, C, D, E, F) were completed. e) The EUT were measured according to the dictates of KDB 680106 D01v02. Report Number : F690501/RF-RTL008943-1 Page: 6 of 11 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 2.3. Equipment Approval Considerations. The EUT does comply with item 5.2 of KDB 680106 D01v02. a) Power transfer frequency is less that 1 ㎒. - The device operates in the frequency range from 110 ㎑ to 190 ㎑. b) Output power from each primary coil is less than 5 watts. - DC 5 V condition  Output power from each primary coil : 5 W (Max.) DC 9 V condition  Output power from each primary coil : 9 W (Max.) c) The transfer system includes only single primary and secondary coils. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils. - The transfer system includes only single primary and secondary coils. Refer to a photo in the Internal photos. d) Client device is inserted in or placed directly in contact with the transmitter. - Client device …

Text truncated - open the document above for the full version.

Report Number : F690501/RF-RTL008945-1 Page: 2 of 24 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) INDEX TABLE OF CONTENTS Page 1. General Information -------------------------------------------------------------------------- 3 2. Field Strength of Fundamental and Spurious Emission ----------------------------- 6 3. 20 ㏈ Bandwidth ----------------------------------------------------------------------------- 16 4. Transmitter AC Power Line Conducted Emission ------------------------------------ 19 Report Number : F690501/RF-RTL008945-1 Page: 3 of 24 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 1. General Information 1.1. Testing laboratory SGS Korea Co., Ltd. (Gunpo Laboratory) - Wireless Div. 2FL, 10-2, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-837 All SGS services are rendered in accordance with the applicable SGS conditions of service available on request and accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx. Phone No. : +82 31 688 0901 Fax No. : +82 31 688 0921 1.2. Details of applicant Applicant : Samsung Electronics Co., Ltd. Address : 129, Samsung-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, Republic of Korea Contact Person : Kim, Kyung-Won Phone No. : +82 31 301 0274 1.3. Description of EUT Kind of Product WIRELESS CHARGER Model Name EP-PN920 Power Supply DC 5 V, DC 9 V (Used AC 100 V ~ 240 V adaptor) Frequency Range 110 ㎑ ~ 190 ㎑ Operating Conditions -20 °C ~ 60 °C Antenna Type Inductive loop coil antenna 1.4. Declarations by the manufacturer - Operation temperature : -20 °C ~ 60 °C Report Number : F690501/RF-RTL008945-1 Page: 4 of 24 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 1.5. Test Equipment List Equipment Manufacturer Model S/N Cal Date Cal Interval Cal Due. Spectrum Analyzer R&S FSV30 103210 Dec. 29, 2014 Annual Dec. 29, 2015 Signal Generator R&S SMBV100A 255834 Jun. 22, 2015 Annual Jun. 22, 2016 Preamplifier H.P. 8447F 2944A03909 Aug. 27, 2014 Annual Aug. 27, 2015 Test Receiver R&S ESU26 100109 Mar. 03, 2015 Annual Mar. 03, 2016 Test Receiver R&S ESCI 7 100911 Dec. 24, 2014 Annual Dec. 24, 2015 Loop Antenna R&S HFH2-Z2 100118 Jun. 04, 2015 Biennial Jun. 04, 2017 Bilog Antenna Schwarzbeck Mess-Elektronik VULB9163 396 Jun. 18, 2015 Biennial Jun. 18, 2017 Two-Line V-Network R&S ENV216 100190 Dec. 25, 2014 Annual Dec. 25, 2015 Antenna Master INN-CO MM4000 N/A N.C.R. N/A N.C.R. Turn Table INN-CO DS 1200 S N/A N.C.R. N/A N.C.R. Anechoic Chamber SY Corporation L × W × H (9.6 m × 6.4 m × 6.6 m) N/A N.C.R. N/A N.C.R. Shield Room SY Corporation L × W × H (6.5 m × 3.5 m × 3.5 m) N/A N.C.R. N/A N.C.R. 1.6. Sample calculation Where relevant, the following sample calculation is provided: Field strength level (㏈㎶/m) = Measured level (㏈㎶) + Antenna factor (㏈) + Cable loss (㏈) – amplifier gain (㏈) Report Number : F690501/RF-RTL008945-1 Page: 5 of 24 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 1.7. Worst case of test configurations In order to check all kinds of possible configurations, EUT was evaluated with appropriate client and under each charging condition as below table. EUT configuration Description Charging Mode with client device Less than 1 % of battery Less than 50 % of battery 100 % full charging of battery 1.8. Summary of Test Results The EUT has been tested according to the following specifications: APPLIED STANDARD: FCC Part 15 Subpart C §15.209 Section in FCC 15 Subpart C Test Item Result 15.209 15.209(a) Radiated emission, Spurious Emission and Field Strength of Fundamental Complied 2.1049 20 ㏈ Bandwidth Complied 15.207 Transmitter AC Power Line Conducted Emission Complied 1.9. Test Report Revision Revision Report number Date of Issue Description 0 F690501/RF-RTL008945 2015.07.20 Initial 1 F690501/RF-RTL008945-1 2015.07.22 Modify the limit unit Report Number : F690501/RF-RTL008945-1 Page: 6 of 24 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Korea Co., Ltd. (Gunpo Laboratory) 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, Korea, 435-040 http://www.sgsgroup.kr RTT5041-20(2014.01.20)(2) Tel. +82 31 428 5700 / Fax. +82 31 427 2370 A4(210 mmx297 mm) 2. Field Strength of Fundamental and Spurious Emission 2.1. Test Setup The diagram below shows the test setup that is utilized to make the measurements for emission from 9 ㎑ to 30 ㎒ Emissions. The diagram below shows the test setup that is utilized to make the measurements for emission from 30 ㎒ to 1 ㎓ Emissions. Rep…

Text truncated - open the document above for the full version.

Test setup photos of EUT 1. Orthogonal planes of EUT - The testing was set in the one orthogonal plane and measured for each position (X). A. X- axis 2. Radiated Field strength Frequency range : 9 ㎑ ~ 30 ㎒ A. The photos of Field strength with client device Client device Frequency range : 30 ㎒ ~ 1 ㎓ A. The photos of Field strength with client device Client device B. The photos of E-field test with client device Client device C. The photos of H-field test with client device Client device D. AC Conducted power line emissions Client device