A3LIWB-P1Zigbee Touch

SyncMaster P64FP P64FT PDP Display User Manual The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Note Prohibited Important to read and under- stand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Ground to prevent an electric shock Power When not used for extended period of time, set your computer to DPM. If using a screen saver, set it to active screen mode. The images here are for reference only, and are not applicable in all cases (or countries). Shortcut to Anti-Afterimage Instructions Do not use a damaged power cord or plug or a damaged or loose power outlet. • Otherwise, this may result in electric shock or fire. Do not touch the power plug with wet hands when removing or plug- ging the plug into the outlet. • Otherwise, this may result in electric shock. Make sure to connect the power cord to a grounded power outlet. • Otherwise, it may result in electric shock or personal injury. Ensure that the power plug is plugged into the power outlet firmly and correctly. • Otherwise, this may result in fire. An administration fee may be charged if either • (a) an engineer is called out at your request and there is no defect in the product (i.e. where you have failed to read this user manual). • (b) you bring the unit to a repair centre and there is no defect in the product (i.e. where you have failed to read this user manual). The amount of such administration charge will be advised to you before any work or home visit is carried out. Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product. • Otherwise, this may result in damage to the product due to electric shock. To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily op- erable. • Otherwise, this may cause electric shock or fire. Use only the power cord provided by our company. Do not use the provided power cord of another product. • Otherwise, this may result in fire or electric shock. Installation Be sure to contact an authorized Service Center when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc. Failure to do so may cause serious damage to your monitor. Ensure that at least two persons lift and move the product. • Otherwise, it may be dropped and cause personal injury, and/or dam- age the product. When installing the product in a cabinet or rack, make sure that the front end of the bottom of the product does not project out. • Otherwise, it may fall or cause personal injury. • Use a cabinet or rack of a size appropriate to the product. DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGA- RETTES AND ANY HEATING APPLIANCES NEAR THE PROD- UCT. • Otherwise, this may result in fire. Keep heating appliances as far away from the power cord or the prod- uct as possible. • Otherwise, this may result in electric shock or fire. Safety Instructions Do not install it in a badly ventilated location such as a bookcase or closet. • Otherwise, this may result in fire due to an increase in the internal temperature. When putting the product down, make sure to put it down softly. • Otherwise, this may result in damage to the screen display. Do not place the front of the product on the floor. • Otherwise, this may result in damage to the screen display. Ensure that an authorized installation company installs the wall mount. • Otherwise, it may fall and cause personal injury. • Make sure to install the specified wall mount. Install your product in a well ventilated location. Ensure that there is a clearance of more than 4 inches (10 cm) from the wall. • Otherwise, it may result in fire due to an increase in the internal tem- perature. Ensure that the packaging vinyl is kept away from children. • Otherwise, it may result in serious harm (suffocation) if children play with it. If the height of your monitor is adjustable, do not place any object or part of your body on the stand when lowering it. • This may cause damage to the product or the person carrying it. Clean When cleaning the PDP Display case or the surface of the TFT-PDP screen, wipe with a slightly moistened, soft fabric.. Do not spray cleaner directly onto the surface of the product. • Otherwise, this may result in the discoloration and distortion of the structure and the screen surface may peel off. When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth. • Otherwise, it may result in fire. When cleaning the product, make sure to disconnect the power cord. • Otherwise, it may result in electric shock or fire. Safety Instructions When cleaning the product, disconnect the power cord and clean it with a soft, dry cloth. • Do not use chemicals such as wax, benzene, alcohol, thinner, mos- quito repellant, lubricant, or cleaner. • These may change the appearance of the product surface and peel off the indication labels on the product. Since the product housing is easily scratched, make sure to use the specified cloth only. When cleaning the product, do not spray water directly onto the main body of the product. • Ensure that water does not enter the product and that it is not wet. • Otherwise, this may result in electric shoc…

Text truncated - open the document above for the full version.

Samsung Electronics Co Ltd 18600 Broadwick St. Rancho Dominguez, CA 90220 United States Date: September 02, 2011 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA RE: Request of Confidentiality for FCCID: A3LIWB-P1 To Whom It may Concern: Pursuant to Sections 0.457 and 0.459 of the Commission`s Rules(CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, Samsung Electronics Co Ltd hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give Samsung Electronics Co Ltd temporary confidentiality of commercially sensitive information prior to product release. The requested permanent and Short-Term Confidential exhibits are listed as follows: PERMANENT & SHORT-TERM CONFIDENTIAL LIST Exhibit Description File name PERMANENT 1 Block Diagram Block Diagram_A3LIWB-P1.pdf 2 Operational Description Operational Description_A3LIWB-P1.pdf 3 Schematics Schematic_A3LIWB-P1.pdf 4 Part Lists Part List_A3LIWB-P1.pdf SHORT-TERM 5 External Photos Ext Photo_A3LIWB-P1.pdf 6 Internal Photos Int Photo_A3LIWB-P1.pdf 7 Test-Setup Photos Test Photo_A3LIWB-P1.pdf 8 Users Manual User Manual_A3LIWB-P1.pdf Note: The pictures on the label location do not require any long term or short term confidentiality. The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be public before the date of the Grant for this application. Sincerely, Peter Ra General Manager

Samsung Electronics Co Ltd 18600 Broadwick St. Rancho Dominguez, CA 90220 United States Date: September 02, 2011 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA LETTER OF AUTHORIZATION We, the undersigned, hereby authorize Harvey Sung of Digital EMC Co., Ltd. to act on our behalf in all manners relating to application for equipment authorization for FCC ID: A3LIWB-P1 including signing of all documents relating to these matters. Any and all acts carried out by Harvey Sung of Digital EMC Co., Ltd. on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from Samsung Electronics Co Ltd Sincerely, Peter Ra General Manager

FCCID: A3LIWB-P1 Copyright Ⓒ 2011, Digital EMC Co., Ltd. View 1 FCCID: A3LIWB-P1 Copyright Ⓒ 2011, Digital EMC Co., Ltd. View 2 FCCID: A3LIWB-P1 Copyright Ⓒ 2011, Digital EMC Co., Ltd. View 3

FCC ID: A3LIWB-P1 Copyright Ⓒ 2011, Digital EMC Co., Ltd. FCC ID SAMPLE LABEL & LOCATION LABELLING REQUIREMENTS PER §2.925 The Label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase. - The FCC label shown is representative of the label that will appear on the radio when in production. Other information may also be included on this label. - The device is so small that it is not practicable to place the statement specified under 15.19 statement request, the information required by this paragraph shall be placed in a prominent location in the user's manual.

FCCID: A3LIWB-P1 Copyright Ⓒ 2011, Digital EMC Co., Ltd. View 1 FCCID: A3LIWB-P1 Copyright Ⓒ 2011, Digital EMC Co., Ltd. View 2 FCCID: A3LIWB-P1 Copyright Ⓒ 2011, Digital EMC Co., Ltd. View 3 FCCID: A3LIWB-P1 Copyright Ⓒ 2011, Digital EMC Co., Ltd. View 4 FCCID: A3LIWB-P1 Copyright Ⓒ 2011, Digital EMC Co., Ltd. View 5 FCCID: A3LIWB-P1 Copyright Ⓒ 2011, Digital EMC Co., Ltd. View 6 FCCID: A3LIWB-P1 Copyright Ⓒ 2011, Digital EMC Co., Ltd. View 7

1012-01377 DRTFCC1109-0332 TRF-RF-201(02)100714 Page 2 / 33 Copyright ○ C 2011, Digital EMC Co., Ltd. CONTENTS 1. Equipment information .............................................................. 3 1.1 Equipment description ............................................................. 3 1.2 Ancillary equipment ................................................................. 3 2. Information about test items ..................................................... 4 2.1 Test mode ................................................................................ 4 2.2 Auxiliary equipment ................................................................. 4 2.3 Tested frequency ..................................................................... 4 2.4 Tested environment ................................................................. 4 2.5 EMI Suppression Device(s)/Modifications ............................... 4 3. Test Report ................................................................................. 5 3.1 Summary of tests .................................................................... 5 3.2 Transmitter requirements ........................................................ 6 3.2.1 6 dB Bandwidth ................................................................... 6 3.2.2 Peak Output Power ............................................................. 9 3.2.3 Out of Band Emissions / Band Edge ................................. 12 3.2.4 Out of band Emission – Radiated ..................................... 23 3.2.5 Transmitter Power Spectral Density .................................. 25 3.2.6 AC Conducted Emissions .................................................. 28 3.2.7 Antenna Requirements ...................................................... 29 APPENDIX..................................................................................... 30 1012-01377 DRTFCC1109-0332 TRF-RF-201(02)100714 Page 3 / 33 Copyright ○ C 2011, Digital EMC Co., Ltd. 1. Equipment information 1.1 Equipment description FCC Equipment Class Digital Transmission System (DTS) Equipment type Zigbee Touch pen Equipment model name IWB-P1 Equipment add model name N/A Equipment serial no. Identical prototype Frequency band 2405 ~ 2480 MHz Modulation type O-QPSK Spread Spectrum DSSS Channel Spacing 5.0 MHz Antenna type Internal Type: Chip Antenna (Max. peak gain: 1.44 dBi) Power Supply DC 3.7 V 1.2 Ancillary equipment Equipment Model No. Serial No. Manufacturer Note - - - - - - - - - - 1012-01377 DRTFCC1109-0332 TRF-RF-201(02)100714 Page 4 / 33 Copyright ○ C 2011, Digital EMC Co., Ltd. 2. Information about test items 2.1 Test mode This device was tested in continuous transmitting mode at maximum power. Test Case 1 - Test Case 2 - 2.2 Auxiliary equipment Equipment Model No. Serial No. Manufacturer Note - - - - - - - - - - 2.3 Tested frequency TX Frequency (MHz) RX Frequency (MHz) Lowest Channel 2405 2405 Middle Channel 2445 2445 Highest Channel 2480 2480 2.4 Tested environment Temperature : 22 ~ 23 o C Relative humidity content : 35 ~ 38 % R.H. Details of power supply :DC 3.7 V 2.5 EMI Suppression Device(s)/Modifications EMI suppression device(s) added and/or modifications made during testing → None 1012-01377 DRTFCC1109-0332 TRF-RF-201(02)100714 Page 5 / 33 Copyright ○ C 2011, Digital EMC Co., Ltd. 3. Test Report 3.1 Summary of tests FCC Part Section(s) Parameter Limit (Using in 2400 ~ 2483.5MHz) Test Condition Status Note 1 I. Test Items 15.247(a)(2) 6 dB Bandwidth > 500 kHz Conducted C 15.247(b)(3) Transmitter Output Power < 1Watt C 15.247(c) Out of Band Emissions / Band Edge 20dBc in any 100kHz BW C 15.247(d) Transmitter Power Spectral Density < 8dBm / 3kHz C 15.205 15.209 General Field Strength Limits (Restricted Bands and Radiated Emission Limits) <FCC 15.209 Limits Radiated C 15.207 AC Conducted Emissions EN 55022 AC Line Conducted C 15.203 Antenna Requirements FCC 15.203 - C Note 1: C=Comply NC=Not Comply NT=Not Tested NA=Not Applicable The sample was tested according to the following specification: ANSI C-63.4-2003, DA00-705 1012-01377 DRTFCC1109-0332 TRF-RF-201(02)100714 Page 6 / 33 Copyright ○ C 2011, Digital EMC Co., Ltd. 3.2 Transmitter requirements 3.2.1 6 dB Bandwidth - Procedure: The bandwidth at 6 dB below the highest inband spectral density was measured with a spectrum analyzer connected to the antenna terminal at the highest, middle and the lowest available channels. After the trace being stable, Use the marker-to-peak function to set the marker to the peak of the emission. Use the marker-delta function to measure 6dB down one side of the emission. Reset the marker-delta function, and move the marker to the other side of the emission, until it is (as close as possible to) even with the reference marker level. The marker-delta reading at this point is the 6 dB bandwidth of the emission. The spectrum analyzer is set to: Center frequency = the highest, middle and the lowest Frequencies Span = 50 MHz (Greater than EBW) RBW = 100 kHz Sweep = auto VBW = ≥ RBW Detector function = peak Trace = max hold - Measurement Data: Comply Test Mode Frequency Test Results (MHz) N/A Lowest 1.35 Middle 1.33 Highest 1.32 Note 1: See next pages for actual measured spectrum plots. - Minimum Standard: The minimum 6 dB bandwidth shall be at least 500 kHz 1012-01377 DRTFCC1109-0332 TRF-RF-201(02)100714 Page 7 / 33 Copyright ○ C 2011, Digital EMC Co., Ltd. 6 dB Bandwidth Lowest Frequency 6 dB Bandwidth Middle Frequency 1012-01377 DRTFCC1109-0332 TRF-RF-201(02)100714 Page 8 / 33 Copyright ○ C 2011, Digital EMC Co., Ltd. 6 dB Bandwidth Test case 1 & Highest Frequency 1012-01377 DRTFCC1109-0332 TRF-RF-201(02)100714 Page 9 / 33 Copyright ○ C 2011, Digital EMC Co., Ltd. 3.2.2 Peak Output Power - Test Procedure and Spectrum Analyzer setting: This is an RF conducted test. Use a direct connection between the antenna port of the transmitter and the spectrum analyzer, through suitable attenuation. Power Output Option 1 is a peak measureme…

Text truncated - open the document above for the full version.

FCC ID: A3LIWB-P1 Copyright Ⓒ 2011, Digital EMC Co., Ltd. Test Setup Photo(RE)