A3LRF4289RSG309LCD control panel module

Free Standing Appliance Refrigerator user manual Imagine the possibilities Thank you for purchasing a Samsung product. To receive a more complete service, please register your product at www.samsung.com/register English RSG309** ,) *-6QVLL"")5 02_ Safety information SAFETY INFORMATION Before using your new Samsung Side-by-side door Refrigerator, please read this manual thoroughly to ensure that you know how to operate the features and functions that your new appliance offers safely and efficiently. This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or those who lack experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Because the following instructions cover various models, the characteristics of your refrigerator may differ slightly from the refrigerator described in this manual. If you have any question, contact us at 1-800-SAMSUNG or find help and information online at www.samsung.com. Important safety symbols and precautions: WARNING Hazards or unsafe practices that may result in severe personal injury or death. CAUTION Hazards or unsafe practices that may result in minor personal injury or property damage. Do NOT attempt. Do NOT disassemble. Do NOT touch. Follow directions carefully. Unplug the power plug from the wall socket. Make sure the refrigerator is grounded to prevent electric shock. Call the contact center for help. Note. These warning signs are here to prevent injury to you and others. Please follow them carefully. After reading this section, keep it in a safe place for future reference. SEVERE WARNING SIGNS FOR INSTALLATION ŘDo not install the refrigerator in a damp place or place where it may come in contact with water. - Deteriorated insulation of electrical parts may cause an electric shock or fire. ŘDo not place this refrigerator in direct sunlight or expose to the heat from stoves, room heaters or other appliance. ŘDo not plug several appliances into the same multiple power strip. The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating that matches the voltage listed on the refrigerator's rating plate. - This provides the best performance and also prevents overloading house wiring circuits, which could cause a fire hazard from overheated wires. ŘIf the wall socket is loose, do not insert the power plug. - There is a risk of electric shock of fire. ŘDo not use a cord that shows cracks or abrasion damage along its length or at either end. ŘDo not bend the power cord excessively or place heavy articles on it. ŘNever unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet. - Damage to the cord may cause a short-circuit, fire and/or electric shock. ŘDo not use aerosols near the refrigerator. - Aerosols used near the refrigerator may cause an explosion or fire. ŘThis refrigerator must be properly installed and located in accordance with the manual before it is used. ŘConnect the power plug in proper position with the cord hanging down. - If you connect the power plug upside down, the wire can get cut off and cause a fire or electric shock. ŘWhen moving the refrigerator, be careful not to roll over or damage the power cord. - This constitutes a fire hazard. Safety Information WARNING ,) *-6QVLL"")5 Safety information _03 01 SAFETY INFORMATION ŘMake sure that the power plug is not squashed or damaged by the back of the refrigerator. ŘKeep the packing materials out of reach of children. - There is a risk of death from suffocation if a child puts the packing materials on his or her head. ŘThe appliance must be positioned so that the plug is accessible after installation. ŘYou need to remove all the protective plastic film before you initially plug the product in. ŘThe refrigerator must be safely grounded - Always make sure that you have grounded the refrigerator before attempting to investigate or repair any part of the appliance. Power leakages can cause severe electric shock. ŘNever use gas pipes, telephone lines or other potential lightning attractors as an electrical ground. - Improper use of the grounding plug can result in a risk of electric shock. If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot receptacle that will accept the plug on the appliance. The marked rating of the extension cord should be AC115-120 V, 10 A, or more. If a grounding adapter is used, make sure the receptacle box is fully grounded. ŘIf the power cord is damaged, have it replaced immediately by the manufacturer or its service agent. CAUTION SIGNS FOR INSTALLATION ŘAllow sufficient space to install the refrigerator on a flat surface. - If your refrigerator is not level, the internal cooling system may not work correctly. ŘKeep the ventilation space in the appliance enclosure or mounting structure clear of obstruction. ŘAllow the appliance to stand for 2 hours after installation. SEVERE WARNING SIGNS FOR USING ŘDo not insert the power plug with wet hands. ŘDo not store articles on the top of the appliance. - When you open or close the door, the articles may fall and cause personal injury and/or material damage. ŘDo not put a container filled with water on the refrigerator. - If spilled, there is a risk of fire or electric shock. ŘChildren should be supervised to ensure that they do not play with the appliance. ŘDo not let children hang on the door. A serious injury may occur. ŘDo not let children enter inside of the refrigerator. There is a risk of children entrapment. ŘDo not insert your hands into the bottom area under the appliance. - Any sharp edges may cause personal injury. ŘDo not let children step on a drawer’s cover. - The drawer may b…

Text truncated - open the document above for the full version.

Date: February 14, 2010 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize Lab Manager Jim. Kim of SGS Testing Korea Co., Ltd and hereafter referred to as SGS Testing Korea, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Lab Manager Jim. Kim of SGS Testing Korea Co., Ltd on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing SGS Testing Korea as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Sang Kyung (Peter) Ra / General Manager Samsung Electronics Co., Ltd.

If you have not received all pages, please call the direct phone number. FAX : 031-428-5859 TEL : 031-428-5744 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: This letter is to comply with Section 0.457(d)(2)(i) and 0.459 pertaining to confidential material. We, Samsung Electronics , would like the following documents regarding this submission for FCC ID: A3LRF4289RSG309 to be kept confidential. 1. Schematics 2. Operating description 3. Block diagram The above m aterial contains trade secrets or technical data, which would custom arily be guarded from competitors. We do not want these documents to be accessible to the general public. Sincerely Yours, Sang Kyung (Peter) Ra / General Manager Samsung Electronics Co., Ltd.

Applicant/Grantee Samsung Electronics Co., Ltd. FCC ID: A3LRF4289RSG309 Section 15.212 Modular Transmitters Request for Modular Approval Request for Limited Modular Approval ■ Requirements EUT Conditions Comply (Y/N) Single Modular Approval Requirements 1 The radio elements of the modular transmitter must have their own installed to Samsung refrigerators. shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. No RF shielding case, limited to be N 2 The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. EUT has proper buffered modulation. Y 3 The modular transmitter must have its own power supply regulation. EUT has its own power supply regulation. Y 4 The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. The antenna, which is SMD type, is permanently connected with W-LAN module. Y 5 The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another installed to Samsung refrigerators, seeks device during testing for compliance limited modular approval. with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting The module was in a stand-alone configuration. But this device will only be N equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)). 6 The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. (A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. (B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC certified transmitter module(s).” Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. Y 7 The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. Such specific rules and operating requirement will be stated in user instruction manual. Y 8 The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. EUT has passed RF exposure evaluation. Refer to F690501/RF-RTL004496. Y A limited modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured.

1 Lucy Tsai From: Loh, Grace (Gunpo) [[email protected]] Sent: Tuesday, March 01, 2011 10:49 PM To: Lucy Tsai Cc: Kang, Noah (Gunpo); Kim, WonSuk (Gunpo); Jeong, Feel (Gunpo) Subject: RE: SAMSUNG ELECTRONICS CO. LTD., //A3LRF4289RSG309 //AN11T0109 Attachments: Request for Modular Approval per section 15 212 requirements.pdf Dear Lucy, I submit the antenna sheet. I reply to answer as below . I hope to get the certificate by today. Thanks, Grace Grace Loh/ 노 윤 정 Wireless Division Section Chief/ 과장 Phone: +82 (0)31 428 5744 Mobile: +82 (0)10 2251 3461 From: Lucy Tsai [mailto:[email protected]] Sent: Monday, February 28, 2011 7:11 PM To: Jeong, Feel (Gunpo); Loh, Grace (Gunpo) Cc: Lucy Tsai Subject: SAMSUNG ELECTRONICS CO. LTD., //A3LRF4289RSG309 //AN11T0109 Hi, Feel and Grace, Please address following issues. Q#1: Since this is a limited modular approval, please provide modular approval request letter per 15.212. [Lucy] Limited approval to certain host, the modular approval request letter based on 15.212 is still required. -> Attached the modular letter Q#2: Except the host label format, please provide the label format and location for the module itself. Be noted that the label format shall be affixed to module as well even it is limited module approval. Q#3: Host user manual should include the RF exposure statement of 20cm separation distance from antenna to user since the device is classified as mobile device. Please address. Q#4: According to the block diagram, schematics and operational description, the RF module is a WLAN & Bluetooth combo card. But this application only address WLAN portion. How about Bluetooth portion? Î BT part is not used. [Lucy] please provide an attestation letter to state that BT is disabled by software. -> Attached to the attestation letter Q#5: Please provide antenna specification sheet. Î Attached to the antenna sheet. Q#6: According to ANSI C63.4, for stand‐alone device, EUT shall be placed in the center of the table. According to test setup photos, EUT was placed in the front edge of the turn table which is not acceptable. Please re‐do the test. 2 Moreover, please advise what the test distance was. According to the test setup photos, it should be less than 3m. Please clarify. Î The edge of table is the center of turn table which is 3 m distance from antenna. [Lucy] But when the turn table turned 180 degree, the distance will then be changed. So, it is still not acceptable. ‐> I understand what you mean. In our case, center point is very important, too. The edge point of red box on the picture as below, include center point. Please refer to the picture. Best Regards, Lucy Tsai/UL CCS Information in this email and any attachments is confidential and intended solely for the use of the individual(s) to whom it is addressed or otherwise directed. Please note that any views or opinions presented in this email are solely those of the author and do not necessaril y represent those of the Company. Finally, the recipient should check this email and any attachments for the presence of viruses. The Company accepts no liability for any damage caused by any virus transmitted by this email. All SGS services are rendered in accordance with the applicable SGS conditions of service available on request and accessible at http://www.sgs.com/terms_and_conditions.htm Information in this email and any attachments is confidential and intended solely for the use of the individual(s) to whom it is addressed or otherwise directed. Please note that any views or opinions presented in this email are solely those of the author and do not necessarily represent those of the Company. Finally, the recipient should check this email and any attachments for the presence of viruses. The Company accepts no liability for any damage caused by any virus transmitted by this email. All SGS services are rendered in accordance with the applicable SGS conditions of service available on request and accessible at http://www.sgs.com/terms_and_conditions.htm 3 Information in this email and any attachments is confidential and intended solely for the use of the individual(s) to whom it is addressed or otherwise directed. Please note that any views or o pinions presented in this email are solely those of the author and do not necessarily represent those of the Company. Finally, the recipient should check this email and any attachments for the presence of viruses. The Company accepts no liability for any damage caused by any virus transmitted by this email. All SGS services are rendered in accordance with the applicable SGS conditions of service available on request and accessible at http://www.sgs.com/terms_and_conditions.htm Information in this email and any attachments is confidential and intended solely for the use of the individual(s) to whom it is addressed or otherwise directed. Please note that any views or opinions presented in this email are solely those of the author and do not necessarily represent those of the Company. Finally, the recipient should check this email and any attachments for the presence of viruses. The Company accepts no liability for any damage caused by any virus transmitted b y this email. All SGS services are rendered in accordance with the applicable SGS conditions of service available on request and accessible at http://www.sgs.com/terms_and_conditions.htm

External photos of EUT Front view of EUT Rear view of EUT Top view of EUT Bottom view of EUT Slide view of EUT

* Label Information - Module Label -When the module’s installed in end product. Samsung Electronics Co., Ltd. Model : RF4289HARS Contains Transmitter Module FCC ID: A3LRF4289RSG309 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Samsung Electronics Co., Ltd. Model: RF4289HARS FCC ID: A3LRF4289RSG309 Made In Korea

FCC Label 1. FCC Label Drawing 2. FCC Label Location Samsung Electronics Co., Ltd. Model : RSG309AARS Contains Transmitter Module FCC ID: A3LRF4289RSG309 This device complies with part 15 of the FCC Rules. Operation is subject to The following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Made in Korea

Internal photos of EUT Top view of main board Bottom view of main board Antenna Top view of LCD module Bottom view of LCD module Top view of Memory card PCB Bottom view of Memory card PCB View of connection between refrigerator and display

Report Number: F690501/RF-RTL004496 Page: 37 of 38 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 8-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.electrolab.kr.sgs.com 7. RF Exposure Evaluation 7.1 Environmental evaluation and exposure limit according to FCC CFR 47 part 1, 1.1307(b), 1.1310 According to FCC 1.1310 : The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in §1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) 7.1.1. Friis transmission formula: Pd = (Pout*G)/(4*pi*R 2 ) Where Pd = power density in ㎽/㎠ Pout = output power to antenna in ㎽ G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd the limit of MPE, 1 ㎽/㎠. If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance where the MPE limit is reached. Frequency Range (㎒) Electric Field Strength(V/m) Magnetic Field Strength (A/m) Power Density (㎽/㎠) Average Time (A) Limits for Occupational /Control Exposures 300 – 1 500 -- -- F/300 6 1 500 – 100 000 -- -- 5 6 (B) Limits for General Population/Uncontrol Exposures 300 – 1500 -- -- F/1 500 6 1 500 – 100 000 -- -- 1 30 Report Number: F690501/RF-RTL004496 Page: 38 of 38 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 8-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.electrolab.kr.sgs.com 7.1.2. Test Result of RF Exposure Evaluation Test Item ： RF Exposure Evaluation Data Test Mode ： Normal Operation 7.1.3. Output Power into Antenna & RF Exposure Evaluation Distance DSSS : 802.11b Channel Channel Frequency (㎒) Output Average Power to Antenna (㏈m) Antenna Gain (㏈i) Power Density at 20cm (㎽/㎠) LIMITS (㎽/㎠) Low 2 412 12.64 0.91 0.00451 1 Middle 2 437 12.98 0.91 0.00487 1 High 2 462 13.30 0.91 0.00524 1 OFDM : 802.11g Channel Channel Frequency (㎒) Output Average Power to Antenna (㏈m) Antenna Gain (㏈i) Power Density at 20cm (㎽/㎠) LIMITS (㎽/㎠) Low 2 412 10.98 0.91 0.00307 1 Middle 2 437 11.35 0.91 0.00335 1 High 2 462 11.87 0.91 0.00377 1 Note : 1. The power density Pd (5th column) at a distance of 20cm calculated from the friis transmission formula is far below the limit of 1 ㎽/㎠ .

Report Number: F690501/RF-RTL004496 Page: 2 of 38 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 8-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.electrolab.kr.sgs.com INDEX Table of contents 1. General information --------------------------------------------------------------------------------------3 2. Transmitter radiated spurious emissions and conducted spurious emission --------------7 3. 6 ㏈ bandwidth ------------------------------------------------------------------------------------------- 21 4. Maximum peak output power --------------------------------------------------------------------------26 5. Power Spectral Density --------------------------------------------------------------------------------- 31 6. Antenna requirement ------------------------------------------------------------------------------------ 36 7. RF Exposure evaluation ------------------------------------------------------------------------------- 37 Report Number: F690501/RF-RTL004496 Page: 3 of 38 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 8-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.electrolab.kr.sgs.com 1. General Information 1.1. Testing Laboratory SGS Testing Korea Co., Ltd. - Wireless Div. 2FL, 18-34, Sanbon-dong, Gunpo-si, Gyeonggi-dong, Korea - 705, Dongcheon-dong Suji-gu, Yongin-si, Gyeonggi-do, Korea www.electrolab.kr.sgs.com Telephone : +82 +31 428 5700 FAX : +82 +31 427 2371 1.2. Details of Applicant Applicant : SAMSUNG ELECTRONICS CO., LTD. Address : 416, Maetan3-dong, Yeongtong-gu, Suwon-si, Gyeonggi-do, Korea Contact Person : Kim, Hyun-Ki Phone No. : +82 +31 200 6441 1.3. Description of EUT Kind of Product LCD CONTROL PANEL Model Name RF4289HARS (the addition of model name : RSG309AARS) Serial Number N / A Power Supply DC 12 V Frequency Range 2412 ~ 2462 ㎒ (802.11b/g) Modulation Technique DSSS, OFDM Number of Channels 11 Antenna Type Integral Type (Chip Antenna) Antenna Gain 0.91㏈i 1.4. Declaration by the manufacturer - All models are exactly same for the hardware and software except material of the frame structure. Model Name Information RF4289HARS Material of the frame structure made by stainless steel RSG309AARS Material of the frame structure made by plastic Report Number: F690501/RF-RTL004496 Page: 4 of 38 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 8-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.electrolab.kr.sgs.com 1.5. Test Equipment List EQUIPMENT MANUFACTURER MODEL CAL DUE. Signal Generator R & S SMR40 Jul. 15, 2011 Spectrum Analyzer R & S FSP40 Jul. 15, 2011 Spectrum Analyzer R & S FSV30 Mar. 31, 2011 Attenuator Agilent 8494B Apr. 02, 2011 Preamplifier H.P 8447F Jul. 05, 2011 Preamplifier Agilent 8449B Mar. 31, 2011 High Pass Filter Wainwright WHK3.0/18G-10SS Sep. 29, 2011 Test Receiver R & S ESU26 Apr. 08, 2011 Bilog Antenna SCHWARZBECK MESSELEKTRONIK VULB9163 Jul. 22, 2011 Horn Antenna R & S HF 906 Oct. 08, 2011 Horn Antenna SCHWARZBECK MESSELEKTRONIK BBHA9170 Mar. 17. 2012 Anechoic Chamber SY Corporation L × W × H (9.6 m×6.4 m×6.6 m) N.C.R. Report Number: F690501/RF-RTL004496 Page: 5 of 38 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 8-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.electrolab.kr.sgs.com 1.6. Summary of Test Results The EUT has been tested according to the following specifications: APPLIED STANDARD:FCC Part15 subpart C Standard section Test Item Result 15.205(a) 15.209 15.247(d) Transmitter Radiated Spurious Emissions Conducted Spurious Emission Complied 15.247(a)(2) 6 ㏈ Bandwidth Complied 15.247(b)(3) Maximum Peak Output Power Complied 15.247(e) Power Spectral Density Complied 15.247(i) 1.1307(b)(1) Maximum Permissible Exposure (Exposure of Humans to RF Fields) Complied Report Number: F690501/RF-RTL004496 Page: 6 of 38 The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This test report cannot be reproduced, except in full, without prior written permission of the Company. SGS Testing Korea Co., Ltd. 8-34, Sanbon-dong, Gunpo-si, Gyeonggi-do, Korea, 435-040 Tel. +82 31 428 5700 / Fax. +82 31 427 2371 www.electrolab.kr.sgs.com 1.7. Conclusion of worst-case The field strength of spurious emission was measured in three orthogonal EUT positions(X-axis,…

Text truncated - open the document above for the full version.