A3LSMM-2CD0480800Remote Radio Head is an 800MHz wireless telecom system

EPNA Ed. 01 Smart MBS RRH-C2 Installation Manual 저작권 이 매뉴얼의 저작권은 삼성전자(주)에 있습니다. 이 매뉴얼은 삼성전자(주)의 서면동의 없이 어떤 형태로도 재생산⋅배포⋅변경할 수 없습니다. 등록상표 이매뉴얼에언급된등록상표는그해당회사소유의등록상표입니다. 제품을 설치 및 운용하기 전에 이 매뉴얼을 반드시 읽고, 매뉴얼의 내용에 따라 제품을 안전하고 올바르게 사용하여 주십시오. 이 매뉴얼은 제품의 기능 향상, 설계 변경에 따라 내용이 수정될 수 있습니다. 수정된 매뉴얼이 필요하거나 매뉴얼의 내 용에 대해 궁금한 사항이 있으면 아래의 주소나 홈페이지로 문의 바랍니다. 주소:경기도수원시영통구매탄3동동수원우체국사서함 105호정보통신동 3층 Document Center ○우 442-600 홈페이지:http://www.samsungdocs.co.kr 제품에 대한 불만 사항이나 요청 사항이 있으면 Call Center로 문의 바랍니다. 전화:1588-4141 ©2011 SAMSUNG Electronics Co., Ltd. All rights reserved. Smart MBS RRH-P4 설치 매뉴얼 © SAMSUNG Electronics Co., Ltd. I Revision History Edition Date Desciption 00 2011. 05. Initial Draft 01 2011. 09. 04 Update Warning Changes or modifications not expressly approved by Samsung could void the user's authority to operate the equipment This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense . Smart MBS RRH-P4 설치 매뉴얼 © SAMSUNG Electronics Co., Ltd. II Table of contents Revision History ___________________________________________________________________ I 1장. Before Installation ________________________________________________1 1.1 System Outlook ________________________________________________________1 1.2 Cable Connection_______________________________________________________7 2장. Installation_____________________________________________________A-1 2.1 System Installation Process ____________________________________________A-1 2.2 RRH Installation ______________________________________________________A-3 2.2.1 Installation Diagram ______________________________________________________A-3 2.4 Mounting ____________________________________________________________A-5 2.4.1 Wall Mount Type_________________________________________________________A-5 2.4.2 Pole Mount Type_________________________________________________________A-7 2.5 RRH ~ Antenna Cable Connection ______________________________________A-9 2.5.1 Feeder Line Connection __________________________________________________A-9 2.5.2 RET Cable Connection _________________________________________________ A-15 2.6 Frame Ground Cable Connection_______________________________________A-18 2.6.1 RRH-C2 Grounding ____________________________________________________ A-18 2.7 Connecting DC and CPRI Cable_________________________________________A-20 2.7.1 RRH-C2 Power Cable Connection________________________________________ A-20 2.7.4 RRH-C2 CPRI Cable Connection ________________________________________ A-27 F.1 Standard Torque for Bolt______________________________________________A-32 Smart MBS RRH-P4 설치 매뉴얼 © SAMSUNG Electronics Co., Ltd. 1 1. Before Installation 1.1 System Outlook RRH-C2 Fig1.1RRH-C2 Outlook 1장. Error! Style not defined. 2 © SAMSUNG Electronics Co., Ltd. RRH-C2 External Interface Fig1.2RRH-C2 External Interface Smart MBS RRH-P4 설치 매뉴얼/Ed.00 © SAMSUNG Electronics Co., Ltd. 3 Capacity This is the specification of RRH-C2. Items Specification Air specification FDD CDMA Operating Frequency DL: 862~ 869 MHz UL: 817 ~ 824 MHz Channel Bandwidth 1.25MHz/5MHz Capacity 1.25 MHz CDMA 5Carriers RF Power per Sector 50 W × 2 T DU~RRH-C2 Interface CPRI 4.0(Optic) Holdover 24 hr Input Voltage This is the input voltage specification of RRH-C2. RRH-C2comply with UL60950 safety regulations. Items Specification Input Power -48VDC Power consumption(MAX) 10.4A (at -48V with 47dBm output power on each ANT) 19.0 A (at -38V with 48.5dBm output power on each ANT) Size and Weight Specification Size(mm) RRH-C2 471(W) ×269(D) ×457(H) Weight(kg) RRH-C2 Max 31 kg 1장. Error! Style not defined. 4 © SAMSUNG Electronics Co., Ltd. Environment condition Items Criteria Specification Temperature -40~55°C (without solar load) GR-487-CORE Sec. 3.26 Humidity 10~95% GR-487-CORE Sec.3.34.2 (Issue 2, April, 2002) R3-204 Altitude -60~1,800 m(-197~6,000 ft) GR-63-CORE Sec.4.1.3 Earthquake Zone 4 GR-63-CORE Sec.4.4.1 GR-487-CORE Sec.3.35.6 Vibration Office Vibration Transportation Vibration GR-63-CORE Sec.4.4.4 GR-487-CORE Sec.3.35.5 GR-63-CORE Sec.4.4.5 GR-487-CORE Sec.3.35.3 Noise (sound pressure level) With 1.5 m(5 ft) distance, 1.0 m(3 ft) Height <65 dBA GR-487-CORE Sec.3.29 EMI Comply with specification FCC Title47 Part 15 Class B GR-1089-CORE EN 55022, EN 55024 EN 301 489 Smart MBS RRH-P4 설치 매뉴얼/Ed.00 © SAMSUNG Electronics Co., Ltd. 5 1.2 Cable Connection Fig1.3Cabling Diagram 3) RRH-C2 Ground Cable [RF Antenna] [MGB] 2) TGB Ground Cable [TGB] Feeder Line Ground Cable (Ground Kit/ with over 7/8 in. Feeder Line) ※ TGB and Ground Kit is required when over 7/8 in. Feeder Line is used. [Rectifier] [UADU] 4) Power Cable 1) MGB Ground Cable 5) CPRI Cable 6) RET Cable 7) RF Cable 1장. Error! Style not defined. 6 © SAMSUNG Electronics Co., Ltd. 표 1.1RRH-C2Connecting Cable From To Cable MGB (Main Ground Bar) 2) MGB Ground Cable : AWG4/0, GV 95 mm 2 ×1C Frame Grounding TGB (Tower Ground Bar) 2) TGB Ground Cable : AWG4/0, GV 95 mm 2 ×1C MGB 3) RRH-C2 Ground Cable : AWG8, GV 6 mm 2 ×1C Rectifier 4) Power Cable : AWG10, 4 mm 2 ×2C-1 UADU 5) CPRI Cable : Optic Cable(Single Mode) RET 6) RET Cable Ass’y ,./RRH-C2 Antenna 7) RF Cable (1/2 in. or 7/8 in. Feeder Line) Smart MBS RRH-P4 설치 매뉴얼 © SAMSUNG Electronics Co., Ltd. A-1 2. Installation 2.1 System Installation Process Fig2.1RRH and Cabling process z Note 1. Equipment intended for installation in Restricted Access Location 2. Installation shall be in …

Text truncated - open the document above for the full version.

SAMSUNG Electronics Co.,Ltd. 416, Maetan‐3dong, Yeongtong‐gu, Suwon‐si, Gyeonggi‐do, Korea 9/2/2011 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Permanent Confidentiality To whom it may concern: In accordance with 47CFR Section 0.457 and Section 0.459 pertaining to confidential material, we hereby request to hold permanently confidential all information contained within the below identified exhibits/document categories submitted pursuant to radio equipment certification requirements for FCC ID: A3LSMM-2CD0480800 1. Block Diagram 2. Operational Description 3. Schematics 4. Parts List / Tune-Up Procedure The above material contains trade secrets and proprietary information as specified by 47CFR 0.457(d) and technical data, which would customarily be guarded from competitors. The public disclosure of this information might be harmful to our company and provide unjustified benefits to our competitors. Sincerely, Kyung‐hoon Baik Engineer SAMSUNG Electronics Co.,Ltd.

SAMSUNG Electronics Co.,Ltd. 416, Maetan-3dong, Yeongtong-gu, Suwon-si, Gyeonggi-do, Korea 09/15/2011 To Whom It May Concern: I hereby appoint Kyung-hoon Baik to sign letters and applications for any filings with regulatory agencies on our behalf, and to receive and exchange data between our company, the agents company and the agency in connection with certification for any products that our company owns or manufactures. Sincerely, ------------------------------------------ Sang Kyung (Peter), Ra/ General Manager Samsung Electronics CO. LTD TEL: 310-900-5250 FAX: 310-537-5500 E-mail: [email protected]

Normal operation: - 48 VDC at 10.4A at full RF power of 100W (50W per antenna port).

This report contains a total of 30 pages and may be reproduced in full only. Partial reproduction may only be done with the written consent of CKC Laboratories, Inc. Powerwave Technologies, Inc. TEST REPORT FOR 800MHz Band Remote Radio Head, LRS08‐T5022‐100 Tested To The Following Standards: FCC Part 90 Subpart S Report No.: 92116‐7 Date of issue: August 4, 2011 This test report bears the accreditation symbol indicating that the testing performed herein meets the test and reporting requirements of ISO/IEC 17025 under the applicable scope of EMC testing for CKC Laboratories, Inc. We strive to create long‐term, trust based relationships by providing sound, adaptive, customer first testing services. We embrace each of our customers’ unique EMC challenges, not as an interruption to set processes, but rather as the reason we are in business. Page 2of 30 Report No.: 92116‐7 TABLE OF CONTENTS Administrative Information .......................................................................................................................... 3 Test Report Information ............................................................................................................................................ 3 Report Authorization ................................................................................................................................................. 3 Test Facility Information ............................................................................................................................................ 4 Site Registration & Accreditation Information .......................................................................................................... 4 Summary of Results ................................................................................................................................................... 5 Conditions During Testing ......................................................................................................................................... 5 Equipment Under Test ............................................................................................................................................... 6 Peripheral Devices ..................................................................................................................................................... 6 FCC Part 90 Subpart s .................................................................................................................................... 7 FCC 90.691 ‐ Emission Mask / Block Edge ................................................................................................................. 7 2.1033(c)(14)/2.1046/90.635 ‐ RF Power Output .................................................................................................... 12 2.1033(c)(14)/2.1049(I)/ ‐ Occupied Bandwidth ..................................................................................................... 15 2.1033(c)(14)/2.1051/90.691(a) ‐ Spurious Emissions at Antenna Terminal .......................................................... 18 2.1033(c)(14)/2.1053/90.691(a) ‐ Field Strength of Spurious Radiation ................................................................. 23 2.1033(c)(14)/2.1055/90.543(c) ‐ Frequency Stability ............................................................................................ 26 Supplemental Information .......................................................................................................................... 29 Measurement Uncertainty ...................................................................................................................................... 29 Emissions Test Details .............................................................................................................................................. 29 Page 3of 30 Report No.: 92116‐7 ADMINISTRATIVE INFORMATION Test Report Information REPORT PREPARED FOR: REPORT PREPARED BY: Powerwave Technologies, Inc. 1801 E. St. Andrew Place Santa Ana, CA 92705 Joyce Walker CKC Laboratories, Inc. 5046 Sierra Pines Drive Mariposa, CA 95338 REPRESENTATIVE: Sean Doan Project Number: 92116 Customer Reference Number: 144378 DATE OF EQUIPMENT RECEIPT: July27, 2011 DATE(S) OF TESTING: July27 ‐August 2, 2011 Report Authorization The test data contained in this report documents the observed testing parameters pertaining to and are relevant for only the sample equipment tested in the agreed upon operational mode(s) and configuration(s) as identified herein. Compliance assessment remains the client’s responsibility. This report may not be used to claim product endorsement by A2LA or any government agencies. This test report has been authorized for release under quality control from CKC Laboratories, Inc. Steve Behm Director of Quality Assurance & Engineering Services CKC Laboratories, Inc. Page 4of 30 Report No.: 92116‐7 Test Facility Information Our laboratories are configured to effectively test a wide variety of product types. CKC utilizes first class test equipment, anechoic chambers, data acquisition and information services to create accurate, repeatable and affordable test results. TEST LOCATION(S): CKC Laboratories, Inc. 110 Olinda Place Brea, CA 92823 In‐Situ Testing: Powerwave Technologies 1801 E. St. Andrew Place Santa Ana, CA 92705 Site Registration & Accreditation Information Location CB # JAPAN CANADA FCC Brea A US0060 R‐2945, C‐3248 & T‐1572 3082D‐1 90473 Page 5of 30 Report No.: 92116‐7 SUMMARY OF RESULTS Standard / Specification: FCC Part 90 Subpart S Description Test Procedure/Method Results Emission Mask / Block Edge FCC 90.691Pass RF Power Output FCC 2.1033(c)(14)/2.1046/90.635Pass Modulation Characteristics – Audio Frequency Response FCC 2.1033(c)(14)/2.1047(a) NA Modulation Characteristics – Modulation Limiting Response FCC 2.1033(c)(14)/2.1047(b) NA Occupied Bandwidth FCC 2.1033(c)(14)/2.1049(I)Pass Spurious Emiss…

Text truncated - open the document above for the full version.