Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
User manual SM-T810 Draft Important safety precautions Failure to comply with the following precautions may be dangerous or illegal. Copyright information ● Bluetooth? is a registered trademark of the Bluetooth SIG, Inc. worldwide. ● JavaTM is a trademark or registered trademark of Sun Microsystems, Inc. ● Picsel and Picsel ViewerTM are trademarks of Picsel Technologies, Inc. Drive safely at all times Do not use a hand-held tablet while driving. Park your vehicle first. Switch off the tablet when refuelling Do not use the tablet at a refuelling point (service station) or near fuels or chemicals. Switch off in an aircraft Wireless tablets can cause interference. Using them in an aircraft is both illegal and dangerous. Switch off the tablet near all medical equipment Hospitals or health care facilities may be using equipment that could be sensitive to external radio frequency energy. Follow any regulations or rules in force. Interference All wireless tablets may be subject to interference, which could affect their performance. Be aware of special regulations Meet any special regulations in force in any area and always switch off your tablet whenever it is forbidden to use it, or when it may cause interference or danger. Water resistance Your tablet is not water-resistant. Keep it dry. Sensible use Use only in the normal position (held to your ear). Avoid unnecessary contact with the antenna when the tablet is switched on. Keep your tablet away from small children Keep the tablet and all its parts, including accessories, out of the reach of small children. Accessories and batteries Use only Samsung-approved accessories, such as headsets and PC data cables. Use of any unauthorised accessories could damage you or your tablet and may be dangerous. Qualified service Only qualified service personnel may repair your tablet. For more detailed safety information, see ¡°Health and safety information¡± on page 20. • The tablet could explode if the battery is replaced with an incorrect type. • Dispose of used batteries according to the manufacturer i’s instructions. Excessive exposure to sound at high volumes can cause hearing damage. Al ways turn the volume down before plugging the eartablets into an audiosource and use only the minimum volume setting necessary to hear your conversation or music. Unpack Make sure you have each item • Tablet • Adapter • User’s manual Suitable Adapter or Charger, certified according to the relevant safety standard, will be provided for each country in use. You can obtain the following accessories for your tablet from your local Samsung dealer. • Multi adapter • Travel charger • Car charger • PC data cable • Portable battery kit • Portable PC data cable • Music controller • Bluetooth mono/ stereop headset kit Get started First steps to operate your tablet Install and charge the tablet 1. 2. Plug the adapter into the tablet. 3. Plug the adapter into a standard AC wall outlet. 4. When the tablet is completely charged (the battery icon stops blinking), unplug the adapter from the power outlet. Remove the adapter from the tablet. Low battery indicator When the battery is low: • a warning tone sounds, • the battery low message displays, and • the empty battery icon [ ] blinks. If the battery level becomes too low, the tablet automatically turns off. Recharge your battery. Keys and display Buttons Function Power • Press and hold to turn the device on or off. • Press and hold for more than 7 seconds to reset the device if it has fatal errors or hang-ups, or freezes. • Press to lock or unlock the device. The device goes into lock mode when the touch screen turns off. Menu • Tap to open a list of options available for the current screen. • Tap and hold on the Home screen to launch Google application. Home • Press to return to the Home screen. • Press twice to launch S Voice application. • Press and hold to open the list of recent applications. Back • Tap to return to the previous screen. Volume • Press to adjust the device volume. Overview of menu functions To access Menu mode, press [환경설정] in ldle mode. T service ChatON Maps Call log Samsung Link Local Tablet Group Play Navigation Contacts S Health Downloads Messaging S Voice Optical Reader Samsung Hub S Memo Messenger Samsung Apps S Translator Play Books WatchON Email Play Movies & TV Camera Shopping & wallet T nao Gallery T cloud App Guide Story Album hoppin T Membership DMB MelOn Remote Care T store Chrome T world T LTE Pack Gmail 11st Music Google SmartWallet Video Voice Search NATE Internet YouTube Calculator Clock Talk Voice Recorder S Planner Google+ Dictionary Settings Play Store My Files B tv mobile Pickat Basket Cyworld SmartTouch Cymera NateOnUC Dropbox Samsung service V3 Mobile 2.0 Help Google Settings Health and safety information Exposure to Radio Frequency (RF) Signals Certification Information (SAR) Your wireless tablet is a radio transmitter and receiver. It is designed and manufactured not to exceed the exposure limits for radio frequency (RF) energy set by the Federal Communications Commission (FCC) of the U.S. government. These FCC exposure limits are derived from the recommendations of two expert organizations, the National Counsel on Ra diation Protection and Measurement (NCRP) and the Institute of Electrical and Electronics Engineers (IEEE). In both cases, the recommendations were developed by scientific and engineering experts drawn from industry, government, and academia after extensive reviews of the scientific literature related to the biological effects of RF energy. The exposure limit set by the FCC for wireless mobile tablets employs a unit of meas urement known as the Specific Absorption Rate (SAR). The SAR is a measure of the rate of absorption of RF energy by the human body expressed in units of watts per kilogram (W/kg). The FCC requires wireless tablets to comply with a safety limit of 1.6 watts per kilogram (1.6 W/kg). The FCC exposure limit incorporates a substantial margin of saf ety to giv…
Text truncated - open the document above for the full version.
Date: May 4, 2015 UL Korea, Ltd. Suwon Laboratory 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 443-823, Korea To whom it may concern: I, the undersigned, hereby authorize UL Korea, Ltd. Suwon Laboratory, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Korea, Ltd. Suwon Laboratory on our behalf shall have the same effect as acts of our own. In authorizing UL Korea as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. l) the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a) This authorization is valid until further written notice from the applicant. Sincerely Yours CHANHO, YOUN General Manager Samsung Electronics CO. LTD TEL: +1-973-808-6362 E-mail: [email protected]
May 20 2015 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: A3LSMT810 To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematics Block Diagram Operational Description Antenna Specification Parts List Tune-Up Procedure UNII device SW security statement Wi-Fi Attestation letter Change list Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 180 days External Photos Internal Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondence during certification review process cannot be granted as confidential documents and such information will be available for public review once the grant of equipment authorization is issued. Best Regards Sincerely, CHANHO, YOUN General Manager Samsung Electronics CO. LTD TEL: +1-973-808-6362 E-mail: [email protected]
Label and Location Model: SM-T810 FCC ID: A3LSMT810 Label: Location: Top Back of device Bottom Tablet : FCC ID is engraved on bottom of the device Label
TL-637 SAR EVALUATION REPORT FCC 47 CFR § 2.1093 IEEE Std 1528-2013 For Bluetooth & DTS/UNII a/b/g/n/ac & ANT+ Tablet FCC ID: A3LSMT810 Model Name: SM-T810 Report Number: 15K20728-S1A Issue Date: 6/2/2015 Prepared for SAMSUNG ELECTRONICS CO., LTD. 129 SAMSUNG-RO, YEONGTONG-GU, SUWON-SI, GYEONGGI-DO, 443-742, KOREA Prepared by UL Korea, Ltd. Suwon Laboratory 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 443-823, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 Report No.: 15K20728-S1A Issue Date: 6/2/2015 Page 2 of 40 UL Korea, Ltd. Suwon Laboratory Doc. No.: 1.0 This report shall not be reproduced except in full, without the written approval of UL Korea, Ltd. Revision History Rev. Date Revisions Revised By -- 5/24/2015 Initial Issue Justin Park A 6/1/2015 1. Sec 10., 12.. : Added Wi-Fi MIMO Data Justin Park Report No.: 15K20728-S1A Issue Date: 6/2/2015 Page 3 of 40 UL Korea, Ltd. Suwon Laboratory Doc. No.: 1.0 This report shall not be reproduced except in full, without the written approval of UL Korea, Ltd. Table of Contents 1. Attestation of Test Results ......................................................................................................... 5 2. Test Specification, Methods and Procedures ............................................................................ 6 3. Facilities and Accreditation ........................................................................................................ 6 4. SAR Measurement System & Test Equipment .......................................................................... 7 4.1. SAR Measurement System ........................................................................................................ 7 4.2. SAR Scan Procedures ............................................................................................................... 8 4.3. Test Equipment ........................................................................................................................ 10 5. Measurement Uncertainty ......................................................................................................... 10 6. Device Under Test (DUT) Information ...................................................................................... 11 6.1. DUT Description ...................................................................................................................... 11 6.2. Wireless Technologies ............................................................................................................. 11 6.3. Nominal and Maximum Output Power ...................................................................................... 12 6.4. Power Reduction by Proximity Sensing ................................................................................... 13 6.4.1. Proximity Sensor Triggering Distance (KDB 616217 §6.2) ................................................ 13 7. RF Exposure Conditions (Test Configurations) ...................................................................... 16 7.1. Standalone SAR Test Exclusion Considerations ...................................................................... 16 7.2. Required Test Configurations .................................................................................................. 20 8. Dielectric Property Measurements & System Check .............................................................. 21 8.1. Dielectric Property Measurements ........................................................................................... 21 8.2. System Check.......................................................................................................................... 24 9. Conducted Output Power Measurements ................................................................................ 26 9.1. Wi-Fi 2.4GHz (DTS Band) ....................................................................................................... 26 9.2. Wi-Fi 5GHz (U-NII Bands)........................................................................................................ 27 9.3. Bluetooth ................................................................................................................................. 31 10. Measured and Reported (Scaled) SAR Results ....................................................................... 32 10.1. Wi-Fi (DTS Band) ................................................................................................................. 33 10.2. Wi-Fi (U-NII Band) ................................................................................................................ 34 10.3. Bluetooth .............................................................................................................................. 35 11. SAR Measurement Variability ................................................................................................... 36 12. Simultaneous Transmission SAR Analysis ............................................................................. 37 12.1. Sum of the SAR for Wi-Fi & BT ........................................................................................... 39 Appendixes .......................................................................................................................................... 40 Report No.: 15K20728-S1A Issue Date: 6/2/2015 Page 4 of 40 UL Korea, Ltd. Suwon Laboratory Doc. No.: 1.0 This report shall not be reproduced except in full, without the written approval of UL Korea, Ltd. A_15K20728-S1 SAR Photos & Ant. Locations .................................................................................. 40 B_15K20728-S1 SAR Highest Test Plots ........................................................................................... 40 C_15K20728-S1 SAR System Check Plots ........................................................................................ 40 D_15K20728-S1 SAR Tissue Ingredients .....................................................…
Text truncated - open the document above for the full version.
Plot No. 1 Test Laboratory: UL Korea Ltd. Suwon Laboratory, SAR 1 Room Date: 2015-04-16 Wi-Fi 2.4GHz_Reduced Frequency: 2437 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 24.0C; Liquid Temperature: 23.0C Medium parameters used (interpolated): f = 2437 MHz; σ = 1.963 S/m; ε r = 50.801; ρ = 1000 kg/m 3 DASY5 Configuration: - Area Scan Setting: Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Electronics: DAE4 Sn1468; Calibrated: 2015-01-12 - Probe: EX3DV4 - SN7330; ConvF(7.32, 7.32, 7.32); Calibrated: 2015-02-12; - Sensor-Surface: 2.5mm (Mechanical Surface Detection) - Phantom: ELI v6.0; Type: QDOVA003AA; Serial: TP:xxxx Rear(Dist 0mm)/802.11b_ch 6 SISO Chain 0/Area Scan (8x11x1): Measurement grid: dx=12mm, dy=12mm. Maximum value of SAR (measured) = 1.03 W/kg Rear(Dist 0mm)/802.11b_ch 6 SISO Chain 0/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 23.07 V/m; Power Drift = 0.00 dB Peak SAR (extrapolated) = 1.82 W/kg SAR(1 g) = 0.628 W/kg; SAR(10 g) = 0.223 W/kg Maximum value of SAR (measured) = 0.991 W/kg 0 dB = 0.991 W/kg = -0.04 dBW/kg Plot No. 2 Test Laboratory: UL Korea Ltd. Suwon Laboratory, SAR 1 Room Date: 2015-05-21 Wi-Fi 5.3GHz_Reduced Frequency: 5290 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 24.0C; Liquid Temperature: 23.0C Medium parameters used: f = 5290 MHz; σ = 5.386 S/m; ε r = 47.173; ρ = 1000 kg/m 3 DASY5 Configuration: - Area Scan Setting: Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Electronics: DAE4 Sn1468; Calibrated: 2015-01-12 - Probe: EX3DV4 - SN7330; ConvF(4.4, 4.4, 4.4); Calibrated: 2015-02-12; - Sensor-Surface: 2mm (Mechanical Surface Detection) - Phantom: ELI v6.0; Type: QDOVA003AA; Serial: TP:xxxx Rear/802.11ac_ch 58 SISO Chan 1/Area Scan (16x8x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = 2.11 W/kg Rear/802.11ac_ch 58 SISO Chan 1/Zoom Scan (7x7x12)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=2mm Reference Value = 19.21 V/m; Power Drift = 0.15 dB Peak SAR (extrapolated) = 7.27 W/kg SAR(1 g) = 0.803 W/kg; SAR(10 g) = 0.174 W/kg Maximum value of SAR (measured) = 2.26 W/kg 0 dB = 2.26 W/kg = 3.54 dBW/kg Plot No. 3 Test Laboratory: UL Korea Ltd. Suwon Laboratory, SAR 1 Room Date: 2015-05-21 Wi-Fi 5.5GHz_Reduced Frequency: 5530 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 24.0C; Liquid Temperature: 23.0C Medium parameters used: f = 5530 MHz; σ = 5.698 S/m; ε r = 46.789; ρ = 1000 kg/m 3 DASY5 Configuration: - Area Scan Setting: Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Electronics: DAE4 Sn1468; Calibrated: 2015-01-12 - Probe: EX3DV4 - SN7330; ConvF(3.9, 3.9, 3.9); Calibrated: 2015-02-12; - Sensor-Surface: 2mm (Mechanical Surface Detection) - Phantom: ELI v6.0; Type: QDOVA003AA; Serial: TP:xxxx Rear/802.11ac_ch 106 SISO Chan 1/Area Scan (16x8x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = 2.60 W/kg Rear/802.11ac_ch 106 SISO Chan 1/Zoom Scan (7x7x12)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=2mm Reference Value = 21.01 V/m; Power Drift = -0.14 dB Peak SAR (extrapolated) = 9.24 W/kg SAR(1 g) = 0.985 W/kg; SAR(10 g) = 0.220 W/kg Maximum value of SAR (measured) = 2.46 W/kg 0 dB = 2.46 W/kg = 3.91 dBW/kg Plot No. 4 Test Laboratory: UL Korea Ltd. Suwon Laboratory, SAR 2 Room Date: 2015-05-21 Wi-Fi 5.8GHz_Reduced Frequency: 5775 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 24.0C; Liquid Temperature: 23.0C Medium parameters used: f = 5775 MHz; σ = 6.174 S/m; ε r = 45.965; ρ = 1000 kg/m 3 DASY5 Configuration: - Area Scan Setting: Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Electronics: DAE4 Sn1447; Calibrated: 2014-08-25 - Probe: EX3DV4 - SN7313; ConvF(4.09, 4.09, 4.09); Calibrated: 2014-08-27; - Sensor-Surface: 2mm (Mechanical Surface Detection) - Phantom: ELI v5.0 (20deg probe tilt); Type: QDOVA002AA; Serial: TP:2005 Rear(Dist 4mm)/802.11ac_ch 155 SISO Chan 1/Area Scan (16x8x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = 2.24 W/kg Rear(Dist 4mm)/802.11ac_ch 155 SISO Chan 1/Zoom Scan (7x7x12)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=2mm Reference Value = 18.56 V/m; Power Drift = 0.17 dB Peak SAR (extrapolated) = 7.28 W/kg SAR(1 g) = 0.844 W/kg; SAR(10 g) = 0.167 W/kg Maximum value of SAR (measured) = 2.42 W/kg 0 dB = 2.42 W/kg = 3.84 dBW/kg Plot No. 5 Test Laboratory: UL Korea, Ltd. Suwon Laboratory, SAR 3 Room Date: 2015-05-01 Bluetooth_0501 Frequency: 2441 MHz; Duty Cycle: 1:1.29033; Room Ambient Temperature: 25.0C; Liquid Temperature: 24.0C Medium parameters used (interpolated): f = 2441 MHz; σ = 2.024 S/m; ε r = 50.708; ρ = 1000 kg/m 3 DASY5 Configuration: - Area Scan Setting: Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Averaged Fast SAR: Polynomial fit - Electronics: DAE4 Sn1446; Calibrated: 2014-08-27 - Probe: EX3DV4 - SN7323; ConvF(7.3, 7.3, 7.3); Calibrated: 2014-12-05; - Sensor-Surface: 2mm (Mechanical Surface Detection) - Phantom: ELI Phantom v5.0; Type: QDOVA002AA; Serial: TP:2001 Rear/802.11a_ch 116 SISO Chan 0/Area Scan (9x7x1): Measurement grid: dx=12mm, dy=12mm Maximum value of SAR (measured) = 0.151 W/kg Rear/802.11a_ch 116 SISO Chan 0/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 8.476 V/m; Power Drift = 0.07 dB Peak SAR (extrapolated) = 0.266 W/kg SAR(1 g) = 0.106 W/kg; SAR(10 g) = 0.041 W/kg Maximum value of SAR (measured) = 0.172 W/kg 0 dB = 0.172 W/kg = -7.64 dBW/kg
Plot No. 1 Test Laboratory: UL Korea Ltd. Suwon Laboratory, SAR1 Room Date: 2015-04-15 20150415_SystemPerformanceCheck-D2450V2 SN 939 Frequency: 2450 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 24.0C; Liquid Temperature: 23.0C Medium parameters used: f = 2450 MHz; σ = 1.981 S/m; ε r = 50.749; ρ = 1000 kg/m 3 DASY5 Configuration: - Area Scan Setting: Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Averaged Fast SAR: Polynomial fit - Electronics: DAE4 Sn1468; Calibrated: 2015-01-12 - Probe: EX3DV4 - SN7330; ConvF(7.32, 7.32, 7.32); Calibrated: 2015-02-12; - Sensor-Surface: 2.5mm (Mechanical Surface Detection), Sensor-Surface: 2mm (Mechanical Surface Detection) - Phantom: ELI v6.0; Type: QDOVA003AA; Serial: TP:2013 Body/Pin=100 mW 2/Area Scan (81x71x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Reference Value = 64.22 V/m; Power Drift = 0.03 dB Fast SAR: SAR(1 g) = 5.25 W/kg; SAR(10 g) = 2.28 W/kg Maximum value of SAR (interpolated) = 7.75 W/kg Body/Pin=100 mW 2/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 64.22 V/m; Power Drift = 0.03 dB Peak SAR (extrapolated) = 11.2 W/kg SAR(1 g) = 5.28 W/kg; SAR(10 g) = 2.4 W/kg Maximum value of SAR (measured) = 8.08 W/kg 0 dB = 8.08 W/kg = 9.07 dBW/kg Plot No. 2 Test Laboratory: UL Korea Ltd. Suwon Laboratory, SAR1 Room Date: 2015-04-15 20150415_SystemPerformanceCheck-D2450V2 SN 939 Frequency: 2450 MHz; Duty Cycle: 1:1 Body/Pin=100 mW 2/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Maximum value of SAR (measured) = 6.96 W/kg Plot No. 3 Test Laboratory: UL Korea Ltd. Suwon Laboratory, SAR 2 Room Date: 2015-05-21 20150521_SystemPerformanceCheck-D5GHzV2 SN 1184 Frequency: 5600 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 24.0C; Liquid Temperature: 23.0C Medium parameters used: f = 5600 MHz; σ = 5.922 S/m; ε r = 46.228; ρ = 1000 kg/m 3 DASY5 Configuration: - Area Scan Setting: Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Averaged Fast SAR: Polynomial fit - Electronics: DAE4 Sn1447; Calibrated: 2014-08-25 - Probe: EX3DV4 - SN7313; ConvF(3.85, 3.85, 3.85); Calibrated: 2014-08-27; - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Phantom: ELI v5.0 (20deg probe tilt); Type: QDOVA002AA; Serial: TP:2005 Body/5.6 GHz, Pin=100mW/Area Scan (61x61x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Reference Value = 51.89 V/m; Power Drift = 0.10 dB Fast SAR: SAR(1 g) = 8.07 W/kg; SAR(10 g) = 2.22 W/kg Maximum value of SAR (interpolated) = 21.9 W/kg Body/5.6 GHz, Pin=100mW/Zoom Scan (8x8x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 51.89 V/m; Power Drift = 0.10 dB Peak SAR (extrapolated) = 38.6 W/kg SAR(1 g) = 8.88 W/kg; SAR(10 g) = 2.44 W/kg Maximum value of SAR (measured) = 21.7 W/kg 0 dB = 21.7 W/kg = 13.36 dBW/kg Plot No. 4 Test Laboratory: UL Korea Ltd. Suwon Laboratory, SAR 2 Room Date: 2015-05-21 20150521_SystemPerformanceCheck-D5GHzV2 SN 1184 Frequency: 5600 MHz; Duty Cycle: 1:1 Body/5.6 GHz, Pin=100mW/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Maximum value of SAR (measured) = 13.7 W/kg Plot No. 5 Test Laboratory: UL Korea, Ltd. Suwon Laboratory, SAR 3 Room Date: 2015-05-26 20150526_SystemPerformanceCheck-D2450V2 SN 939 Frequency: 2450 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 24.0C; Liquid Temperature: 23.0C Medium parameters used: f = 2450 MHz; σ = 1.985 S/m; ε r = 52.063; ρ = 1000 kg/m 3 DASY5 Configuration: - Area Scan Setting: Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Averaged Fast SAR: Polynomial fit - Electronics: DAE4 Sn1446; Calibrated: 2014-08-27 - Probe: EX3DV4 - SN7323; ConvF(7.3, 7.3, 7.3); Calibrated: 2014-12-05; - Sensor-Surface: 4mm (Mechanical Surface Detection), Sensor-Surface: 2.5mm (Mechanical Surface Detection) - Phantom: ELI Phantom v5.0; Type: QDOVA002AA; Serial: TP:2001 Body/Pin=100 mW 2 2/Area Scan (61x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Reference Value = 63.41 V/m; Power Drift = 0.05 dB Fast SAR: SAR(1 g) = 5.24 W/kg; SAR(10 g) = 2.34 W/kg Maximum value of SAR (interpolated) = 6.20 W/kg Body/Pin=100 mW 2 2/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 63.41 V/m; Power Drift = 0.05 dB Peak SAR (extrapolated) = 11.0 W/kg SAR(1 g) = 5.3 W/kg; SAR(10 g) = 2.44 W/kg Maximum value of SAR (measured) = 7.60 W/kg 0 dB = 7.60 W/kg = 8.81 dBW/kg Plot No. 6 Test Laboratory: UL Korea, Ltd. Suwon Laboratory, SAR 3 Room Date: 2015-05-26 20150526_SystemPerformanceCheck-D2450V2 SN 939 Frequency: 2450 MHz; Duty Cycle: 1:1 Body/Pin=100 mW 2 2/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Maximum value of SAR (measured) = 3.89 W/kg
Head Tissue Simulating Liquids Head Tissue Parameters according to IEEE Std 1528-2013 / IEC 62209 / FCC KDB 865664 D01 Narrow- Band Solutions (±5% tolerance) Product HSL300V2 HSL450V2 HSL750V2 HSL900V2 HSL1450V2 HSL1750V2 HSL1800V2 HSL1900V2 HSL1950V2 HSL2450V2 Test Frequency (MHz) 300 450 750 835, 900 1450, 1500, 1640 1750 1800, 1900 1900 1950, 2000 2450, 2600 Main Ingredients Water, Sugar Water, Sugar Water, Sugar Water, Sugar Water, DGBE Water, DGBE Water, DGBE Water, DGBE Water, DGBE Water, DGBE Broad- Band Solutions (±5% tolerance) Product HBBL30-250V3 HBBL1350-1850V3 HBBL1550-1950V3 HBBL1900-3800V3 HBBL3500-5800V5 Test Frequency (MHz) 30-250 1400-1800 1750-1900 1950-3000 3500-5800 Main Ingredients Water, Tween Water, Tween Water, Tween Water, Tween Water, Oil Body Tissue Simulating Liquids Body Tissue (Muscle) Parameters according to FCC KDB 865664 D01 Narrow- Band Solutions (±5% tolerance) Product MSL300V2 MSL450V2 MSL750V2 MSL900V2 MSL1450V2 MSL1750V2 MSL1800V2 MSL1900V2 MSL1950V2 MSL2450V2 Test Frequency (MHz) 300 400, 450 750 835, 900 1450, 1500, 1640 1750 1800, 1900 1900 1950, 2100 2450, 2600 Main Ingredients Water, Sugar Water, Sugar Water, Sugar Water, Sugar Water, DGBE Water, DGBE Water, DGBE Water, DGBE Water, DGBE Water, DGBE Broad- Band Solutions (±5% tolerance) Product MBBL130-250V3 MBBL1350-1850V3 MBBL1550-1950V3 MBBL1900-3800V3 MBBL3500-5800V5 Test Frequency (MHz) 130-250 1350-1800 1550-1850 1950-3800 3500-5800 Main Ingredients Water, Tween Water, Tween Water, Tween Water, Tween Water, Oil
TL-637 FCC 47 CFR PART 15 SUBPART E INDUSTRY CANADA RSS-247 ISSUE 1 CERTIFICATION TEST REPORT FOR Bluetooth/BLE and DTS/UNII a/b/g/n/ac and ANT+ Tablet MODEL NUMBER : SM-T810 FCC ID: A3LSMT810 IC ID: 649E-SMT710 REPORT NUMBER: 15K20728-E4 ISSUE DATE: MAY 30, 2015 Prepared for SAMSUNG ELECTRONICS CO., LTD. 129 SAMSUNG-RO, YEONGTONG-GU, SUWON-SI, GYEONGGI-DO, 443-742, KOREA Prepared by UL Korea, Ltd. Suwon Laboratory 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 443-823, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 REPORT NO: 15K20728-E4 DATE: MAY 30, 2015 IC ID: 649E-SMT810 MODEL NUMBER: SM-T810 FCC ID: A3LSMT810 Page 2 of 44 UL Korea, Ltd. Suwon Laboratory FORM ID: FCC_15E 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 443-823, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 UL Korea, Ltd. Confidential This report shall not be reproduced except in full, without the written approval of UL Korea, Ltd. Revision History Rev. Issue Date Revisions Revised By -- 05/23/15 Initial issue CY Choi A 05/30/15 Update section 5.2 CY Choi REPORT NO: 15K20728-E4 DATE: MAY 30, 2015 IC ID: 649E-SMT810 MODEL NUMBER: SM-T810 FCC ID: A3LSMT810 Page 3 of 44 UL Korea, Ltd. Suwon Laboratory FORM ID: FCC_15E 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 443-823, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 UL Korea, Ltd. Con…
Text truncated - open the document above for the full version.
| # | Rule Parts | Frequency Range | Power Output |
|---|---|---|---|
| 4 | 15E | 5.75 GHz - 5.83 GHz | 28.00 mW |
Portable Handset
Equipment Class
6VL - 15E 6 GHZ Very Low Power DeviceBT,BLE Tablet DTS,UNII a,b,g,n,ac,ax,be and digitizer
Equipment Class
DTS - Digital Transmission SystemPortable Handset
Equipment Class
6CD - 15E 6 GHz Low Power Dual ClientBT,BLE Tablet DTS,UNII a,b,g,n,ac,ax and Digitizer
Equipment Class
DSS - Part 15 Spread Spectrum TransmitterWCDMA, LTE, 5G NR Tablet BT,BLE, DTS,UNII a b g n ac ax and Digitizer
Equipment Class
JBP - Part 15 Class B Computing Device Peripheral