A3LSW252CD-R/ RW Drive - Internal

Safety Precautions 2 The following diagrams illustrate the precautions to be taken when usingyour CD-R/RW drive. ✱ Changes or modifications not expressly approved by the party responsible forcompliance could void the user’s authority to operate the equipment. You must not use the drive in any manner other than that specified in this guide. Avoid exposing your eyes or skin to direct or scattered radiation. CAUTION Do not attempt to repair the CD-R/RW drive yourself.Contact your dealer or local SAMSUNG representative for all repairs.If you make any adjustments or perform any operations other than thosespecified in this guide, you run the risk of exposure to hazardous radiation. WARRANTY Please refer to the Samsung limited warranty statements. PRECAUTIONS 1. To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. 2. Always check each disc for cracks before using it. If there are cracks on the surfaces, especially around the border of the centerhole, we recommend that you make a copy of the disc immediatelyand then stop using it. If you continue using the disc, it will probablydevelop more cracks and eventually cause irreparable damage. 3. Do not use poor quality discs: From unknown sourcesWithout any copyrightScratched or damaged in any way CD-R/RW DRIVESW-252 User's Guide FCC Compliance This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmfulinterference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and,if not installed and used in accordance with the instructions, may cause harmfulinterference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception,which can be deter-mined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the followingmeasures: Re-orient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to whichthe receiver is connected.Consult the dealer or an experienced radio/TV technician for help. 4 Upgrading the Firmware Flash Memory The product firmware can be upgraded by downloading the updated file from thefollowing Web site: http:// www.samsung-ODD.com www.samsungelectronics.com System Requirements Before you install the CD-R/RW drive, we strongly recommend that you check thatyour setup meets the system requirements listed below.Item Description Computer Intel Pentium II (or higher), 64 MB of RAM (or higher) with an E-IDE interface Disk space 700 MB minimum Windows version Windows 98 / 2000 / ME or XP / Windows NT 4.0 (or higher) General DMA Installation Guide Windows 95/98/Me Important!Please read the entire DMA installation guide before installing your CD-R/RW drive.About DMA InstallationFor stable writing performance at high speeds, Installation of DMA transfer mode for E-IDEinterface is strongly recommended. We recommend DMA mode for fast writing.DMA SettingBefore you install your CD-R/RW drive, we recommend to set DMA to enabled on yourPC system. See the following procedure to set DMA transfer mode in windowsoprerating system. (Windows 95 OSR2/98/ME) Click on START  Click on Settings  Select Control Panel  Select the System Icon  Select the Device Manager panel in System Properties  Expand the CD-ROM icon  Select your CD-R/RW drive  Click on the Properties button  Click on the Settings tab  Check the DMA checkbox to enables DMA.  Click OK  Restart your PC Windows 2000/XPSelect the DMA mode by selecting [Start > Setting > Control Panel > System >Device Manager > IDEATA/ATAPI Controller > Default/Assistant IDE ChannelAdvanced Information] Your CD-R/RW Drive 3 1. Connector for stereo headphones with a 3.6 mm stereo mini-jack.2. Headphone volume control.3. Emergency eject hole. (if the compartment does not open when you press the Eject button, power off the computer, insert a pin or unfoldedpaper clip in the hole and push firmly) 4. Indicator Light. (GREEN: Read RED: Record)5. Disc compartment. (the compartment opens and closes automatically when you press the Eject button) 6. Eject button.1. Two-pin digital audio output terminal for use with a sound or MPEG card supporting digital audio features. 2. Four-pin sound output terminal for use with a sound card. (refer to the sound card documentation for further details) 3. Master/slave select terminal.4. 40pin host E-IDE interface connector.5. 4pin power terminal. 12 3 4 5 6 1 23 4 5 6 5 Installing the CD-R/RW DriveConnecting the Cables To install your CD-R/RW drive in the PC, proceed as follows.1 Make sure that the PC is powered off and disconnected from any power source. 1 Connecting the power cableThe 4-pin power cable from the internal power unit of your computer must beconnected to the power terminal on the rear of the CD-R/RW drive. Note : An improperly connected power cable may cause trouble. Check the direction of the power connector and the incline side of the CD-R/RW drive before connecting. Cut side 2 Connecting the E-IDE cableInsert the IDE cable (40-pin), which is connected to the hard disk to the interfaceterminal. (Place the red line of the cable close to the Pin 1.) Connect the cable to the SL (Slave) of the Master/Slave Select Terminal atthe rear of the CD-R/RW drive. When using one E-IDE cableWhen using two E-IDE cable 2 If necessary, attach a horizontal bracket toboth sides of the drive. Use of the brackets depends on your computer model;you can purchase these accessories separately fromyour computer dealer. 3 Remove the cover from a free expansion slotand install the CD-R/RW drive,as shown in the illustration. If you have no free expansion slot,i…

Text truncated - open the document above for the full version.

14 Block Diagram

SW-252B PHOTO PICTURE 후 후후 후면 면면 면 전 전전 전면 면면 면

Page 17 of 18 Project NO. : LBE021123 5. FCC Label Configuration and Location 5.1 Label Configulation 5.2 Location of Label This report shall not be reproduced except in full, without the written approval of SEC EMC Testing laboratory.

SET 내 내내 내부 부부 부면 면면 면 PCB 상 상상 상단 단단 단면 면면 면 PCB 하 하하 하단 단단 단면 면면 면

Page 1 of 18 Project NO. : LBE021123 Product : CD-R/RW DRIVE Model No. : SW-252(Ver.B) FCC ID : A3LSW252 1. This test reports shall not be reproduced except in full, without the written approval of SEC EMC Testing laboratory. 2. This test reports does not constitute an endorsement by NIST/NVLAP or U.S Government. 3. This test report is to certify that the tested device properly complies with the requirements of FCC Rules and Regulations Part 15 Subpart B Unintentional Radiators. All tests necessary to show compliance to the requirements were and these results met the specifications requirement. Date of test : December 05, 2002 ~ December 09, 2002 Issued Date : December 10, 2002 Tested by: Jin Hwan, Jung/ Test Engineer Reviewed by: Yang Soo, KIM / Manager of EMC Lab. Authorised by: Kyu Baek, CHUNG / Chief of EMC Lab. This laboratory is registered by the NIST/NVLAP, U.S.A. The test reported herein have been performed in accordance with its terms of registration. EMI TEST REPORT According to FCC Part 15 Subpart B/Class B NVLAP Code: 200447 Page 2 of 18 Project NO. : LBE021123 Table of Contents 1. General Information 1.1 Product Description 1.2 Configuration of EUT and peripherals 1.3 Used Cable Description 1.4 System Block Diagram of Test Configuration 1.5 Test Facility 2. System Test Configuration 2.1 Configuration of Radiated and Conducted Interference Measurement 2.2 Operation Environment 2.3 Test Procedure 3. Conducted Emission Test Data 4. Radiated Emission Test Data 5. Label Configuration and Location 6. Test Equipment Used Distribution This test report has been made available as follows: CS Management Center, EMC Laboratory 1 original OMS Division 1 copy This report shall not be reproduced except in full, without the written approval of SEC EMC Testing laboratory. Page 3 of 18 Project NO. : LBE021123 1. General Information Applicant : Samsung Electronics Co., Ltd. Digital Media Network, OMS Division Full Address : 416 Maetan 3 Dong, Paldal-Ku, Suwon City, Kyungki Do, Korea, 442-742 Kind of Product :CD-R/RW DRIVE FCC ID:A3LSW252 Project Name :- Model & Variant Names : SW-252(Ver.B) (Brand Name: Samsung) Test Report Produced by :Jin Hwan, Jung/ Test Engineer This report shall not be reproduced except in full, without the written approval of SEC EMC Testing laboratory. Page 4 of 18 Project NO. : LBE021123 1.1 Product Description 1) Justification The system was configured for testing in typical fashion use. Cable were attached to each of the available I/O Ports. Where applicable, peripherals were attached to the I/O cables. The mode of operation utilized for testing was selected to best simulate typical EUT use. The system was pre-tested using the below additional components, and we found worst emission level for the components, were selected as the final components for the test. And then the system was tested with the configuration of clause 1.4 In each test mode, Finally we found worst case emission that is above configuration with the Worst case components(in the above table). So, the DATA of the maximum EUT operation was reported. Further details of cabling and configuration are shown in the test system configuration. This report shall not be reproduced except in full, without the written approval of SEC EMC Testing laboratory. Compaq Ear-PhoneSony 53B320A4DLM0EN CX151S-AZ M-U48a SDM454DUL - ComponentBrand and Model NameRemark Key-Board Computer LCD Monitor Mouse Compaq Samsung Logitech CD-R/RW Drive EUT/SamsungSW-252(Ver.B) Page 5 of 18 Project NO. : LBE021123 2) Operating Frequency : 1. Resonator : 33.86Mhz 2. HFM : 280±20 Mhz 3) Description of Testing operating mode 4) Manufacturer : SAMSUNG Electronics Co., Ltd. This report shall not be reproduced except in full, without the written approval of SEC EMC Testing laboratory. CD-ROM MODE CD-RW MODE Operating Mode Operating section of EUT CD-R MODE CD-ROM MODE Continously Audio CD playing by EUT Page 6 of 18 Project NO. : LBE021123 1.2 Configuration of EUT and peripherals MarkItemModel No.Serial No.ManufacturerFCC ID A CD-R/RW Drive SW-252(Ver.B ) None Samsung EUT BD/T PC 53B320A4DLM0EN 3D13JCD2208M Compaq- CLCD MonitorCX151S-AZ N192H4NT319256 Samsung- DUSB MouseM-U48a LZE95183958 Logitech- EUSB Key-BoardSDM454DUL B354ALP0BL1VKW Compaq- FEar-PhoneNoneNoneSony- This report shall not be reproduced except in full, without the written approval of SEC EMC Testing laboratory. Page 7 of 18 Project NO. : LBE021123 1.3 Used Cable Description No.ItemLength[m]Shielded (Y/N)Remark 1AC Power Cable1.7N- 2Monitor Cable1.2Y- 3Mouse Cable1.2N- 4Key-Board Cable1.2N- 5AC Power Cable1.7N- 6Ear-Phone Cabe0.7N- This report shall not be reproduced except in full, without the written approval of SEC EMC Testing laboratory. Page 8 of 18 Project NO. : LBE021123 1.4 System Block Diagram of Test Configuration 1.5 Test Facility All test described in this report were performed by : SAMSUNG ELECTRONICS CO., LTD. EMC TESTING LABORATORY 416 Maetan 3 Dong, Paldal-Ku, Suwon City, Kyungki Do, Korea, 442-742 Semi Anechoic Chamber #2(Registration Number:873282) and Shielded Room. This test facility has been filed in FCC under the criteria in ANSI C63.4-1992. This report shall not be reproduced except in full, without the written approval of SEC EMC Testing laboratory. E B D A AC POWER AC POWERAC POWER AC POWER AC POWER AC POWERAC POWER AC POWER 1 11 1 2 22 2 3 33 3 4 44 4 5 55 5 F 6 66 6 C Page 9 of 18 Project NO. : LBE021123 2. System Test Configuration 2.1 Configuration of Radiated and Conducted Interference Measurement * Cabling was taken into consideration and test data was taken under worse case conditions. 1)Conduction(Front View) 2)Conduction(Rear View) This report shall not be reproduced except in full, without the written approval of SEC EMC Testing laboratory. Page 10 of 18 Project NO. : LBE021123 3) Radiation(Front View) 4) Radiation(Rear View) This report shall not be reproduced except in full, without the written approval of SEC EMC Testing laboratory. Page 1…

Text truncated - open the document above for the full version.

Page 9 of 18 Project NO. : LBE021123 2. System Test Configuration 2.1 Configuration of Radiated and Conducted Interference Measurement * Cabling was taken into consideration and test data was taken under worse case conditions. 1)Conduction(Front View) 2)Conduction(Rear View) This report shall not be reproduced except in full, without the written approval of SEC EMC Testing laboratory. Page 10 of 18 Project NO. : LBE021123 3) Radiation(Front View) 4) Radiation(Rear View) This report shall not be reproduced except in full, without the written approval of SEC EMC Testing laboratory.