A45-CEK9PROXRDRAccess Control Reader

Mini 8000 Series Proximity Reader Installation Manual Parts o 1 - Certis reader o 1 - Installation manual o 2 - 0.75” self tapping screws Required Tools o Up to 8 wire splices (pigtail) o Cable, 5-9 conductor (Weigand or RS232), 24 AWG FT4 (pigtail) o Linear DC power supply o Gang box (optional) o Security tool for anti tamper screw Mounting 1. Fasten the metal base plate to the wall with two screws to the wall or gang box (optional)  (gang box not included). 2. Clip the top edge of the cover  , followed by the bottom edge of the reader. 3. Secure the reader to t he base plate by fastening the security screw at the base of the reader  . Installation is completed. Specifications Input voltage (Reader end) DC10V~15V Average read range > 5cm Operating current 160mA (max) Maximum cable length 150m Operating temperature -30ºC~70 ºC Recommendations 1. Linear DC Power Supply 2. 22AWG shielded cable; “One-point” ground recommended (refer to diagram) Wiring Color Label Description (Default for SpeedGuard) Red +12V dc Power Supply to reader,VR1,VR2...VR4 Black GND Signal GND Green Data0 Wiegand Output data, I1D0,I2D0...I4D0 White Data1 Wiegand Output data, I1D1,I2D1...I4D1 Yellow No Use No use Blue LED LED control, LED1,LED2...LED4 Brown Buzzer Buzzer input, ac tive low ,Buz1,Buz2...Buz4 Orange Tamper Tamper output (open collector, Active low, max 100mA) V2.6 Mini 8000 Series Proximity Reader Installation Manual Power & Testing 1. When reader is powered up, the green LED will flicker for 5 seconds. The reader will beep once and the reader is in Ready mode. 2. Present the card. The Blue LED will flicke r once; the back lit will light for 5 seconds; buzzer will beep once. Using the Configuration Card 1. When reader is powered up, the green LED will flicker for 5 seconds. 2. Present the Conf iguration Card. A 1-second beep indicates a successful attempt. Configuration cards are available for:  LED Response Status ○ SpeedGuard LED （ Default ） ○ Cardax LED Physical Dimension Troubleshooting Symptom Solution No response when powered up o Disconnect the power and confirm that the power supply cable is correctly connected (Refer to Wiring table) o Check the input voltage is sufficient (Refer to Specifications table) Auto restart o Check the input voltage is sufficient ( Refer to Specifications table) Card number not read correctly o Verify that the format setting on t he controller is the same as the card format. Use approved card (known format and Facility Code) to test o Check that the shield cable is correctly connected to Chassis Ground at ONE point only Reader beeps but no card data o Check that Data 0 and Data 1 cable are correctly connected (Refer to Wiring table). o Check the input voltage at the card reader end is correct (Refer to Specifications table) No buzzer sound o Verify that the buzzer cable is correctly connected (Refer to Wiring table) Mini 8000 Series Proximity Reader Installation Manual FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cau se harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions , may cause harmful interference to radio communications. However, there is no guarantee that inte rference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. V2.6

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 2.0 2206 Ringwood Avenue San Jose, CA 95131 Tel: 408-526- 1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (current) 1.0 1.0 Nov-14-2006 Revised wording (current) 1.0 2.0 Sept–25-2007 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 2.0 6 December 2011 SIEMIC, INC. 2206 Ringwood Avenue, San Jose, CA 95131 USA Dear Sir/Madam, Project and Product Certification Representative Authorization Letter Certis Technology International Pte Ltd hereby authorizes SIEMIC, INC. to act as a Certification Body for certifying for the following project: Product description：Access Control Reader Model names： RP-8000 RPK-8000 MP-8000 OPK-8000 RE-8000 ME-8000 REK-8000 ME-3000 REK-3000 RE-3000 MP-3000 RPK-3000 RP-3000 We affirm that between SIEMIC and Certis Technology International Pte Ltd, any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Yours sincerely Khoo Ri Na Certis Technology International Pte Ltd

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 2.0 2206 Ringwood Avenue San Jose, CA 95131 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (current) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 1.0 2.0 August – 11 - 2008 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 2.0 6 December 2011 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Confidentiality Request regarding application for certification of FCC ID: A45-CEK9PROXRDR We hereby request confidential treatment of information accompanying this application as outlined below: • Block Diagram • Operational Description • Schematic The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Yours sincerely, Khoo Ri Na Head, Product Development Certis Technology International

Front View Rear View of w of EUT fEUT Bottom View o To p View of of EUT f EUT Left View o Right View of EUT w of EUT

Country of origin： This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Trade name: Certis Singapore Model number: MP -8 0 0 0 FCC ID: A45-CEK9PROXRDR

FCC ID: A45-CEK9PROXRDR

Certis Technology International Pte Ltd. Access Control Reader Model: MP-8000 November 21, 2011 Report No.: 11021322-FCC (This report supersedes NONE) Modifications made to the product : None This Test Report is Issued Under the Authority of: Deon Dai Alex Liu Test Engineer Technical Manager This test report may be reproduced in full only. Test result presented in this test report is applicable to the representative sample only. Title: RF Test Report for Access Control Reader Model: MP-8000 To: FCC Part 15.207;15.209: 2011 Serial#: 11021322-FCC Issue Date: November 21, 2011 Page: 2 of 34 www.siemic.com.cn Laboratory Introduction ATION SIEMIC, headquartered in the heart of Silicon Valley, with superior facilities in US and Asia, is one of the leading independent testing and certification facilities providing customers with one-stop shop services for Compliance Testing and Global Certifications. In addition to testing and certification, SIEMIC provides initial design reviews and compliance management through out a project. Our extensive experience with China, Asia Pacific, North America, European, and international compliance requirements, assures the fastest, most cost effective way to attain regulatory compliance for the global markets. Accreditations for Conformity Assessment Country/RegionAccreditation Body Scope USA FCC, A2LA EMC , RF/Wireless , Telecom Canada IC, A2LA, NIST EMC, RF/Wireless , Telecom Taiwan BSMI , NCC , NIST EMC, RF, Telecom , Safety Hong Kong OFTA , NIST RF/Wireless ,Telecom Australia NATA, NIST EMC, RF, Telecom , Safety Korea KCC/RRA, NIST EMI, EMS, RF , Telecom, Safety Japan VCCI, JATE, TELEC, RFT EMI, RF/Wireless, Telecom Mexico NOM, COFETEL, Caniety Safety, EMC , RF/Wireless, Telecom Europe A2LA, NIST EMC, RF, Telecom , Safety Accreditations for Product Certifications Country Accreditation Body Scope USA FCC TCB, NIST EMC , RF , Telecom Canada IC FCB , NIST EMC , RF , Telecom Singapore iDA, NIST EMC , RF , Telecom EU NB EMC & R&TTE Directive Japan MIC, (RCB 208) RF , Telecom HongKong OFTA (US002) RF , Telecom Title: RF Test Report for Access Control Reader Model: MP-8000 To: FCC Part 15.207;15.209: 2011 Serial#: 11021322-FCC Issue Date: November 21, 2011 Page: 3 of 34 www.siemic.com.cn This page has been left blank intentionally. Title: RF Test Report for Access Control Reader Model: MP-8000 To: FCC Part 15.207;15.209: 2011 Serial#: 11021322-FCC Issue Date: November 21, 2011 Page: 4 of 34 www.siemic.com.cn CONTENTS 1 EXECUTIVE SUMMARY & EUT INFORMATION.............................................................................................................5 2 TECHNICAL DETAILS..................................................................................................................................................6 3 MODIFICATION............................................................................................................................................................7 4 TEST SUMMARY..........................................................................................................................................................8 5 MEASUREMENTS, EXAMINATION AND DERIVED RESULTS........................................................................................9 ANNEX A. TEST INSTRUMENT & METHOD........................................................................................................................18 ANNEX B. EUT AND TEST SETUP PHOTOGRAPHS...........................................................................................................22 ANNEX C. TEST SETUP AND SUPPORTING EQUIPMENT...................................................................................................28 ANNEX D. USER MANUAL / BLOCK DIAGRAM / SCHEMATICS / PART LIST.......................................................................32 ANNEX E. SIEMIC ACCREDITATION CERTIFICATES..........................................................................................................33 Title: RF Test Report for Access Control Reader Model: MP-8000 To: FCC Part 15.207;15.209: 2011 Serial#: 11021322-FCC Issue Date: November 21, 2011 Page: 5 of 34 www.siemic.com.cn 1 Executive Summary & EUT information The purpose of this test programme was to demonstrate compliance of the Certis Technology International Pte Ltd., Access Control Reader , and model: MP-8000 against the current Stipulated Standards. The Access Control Reader has demonstrated compliance with the FCC Part 15.207;15.209: 2011. EUT Information EUT Description : Access Control Reader Model No : MP-8000 (Note) Serial No : N/A Input Power : Voltage:10-15V, Current:160mA(max) Classification Per Stipulated Test Standard : FCC Part 15.207; 15.209:2011 Note: Series model RP-8000, RPK-8000, OPK-8000, ME-8000, REK-8000, RE-8000, ME-3000, REK-3000, RE-3000, MP-3000, RPK-3000, RP-3000, only look different other identical. Title: RF Test Report for Access Control Reader Model: MP-8000 To: FCC Part 15.207;15.209: 2011 Serial#: 11021322-FCC Issue Date: November 21, 2011 Page: 6 of 34 www.siemic.com.cn 2 TECHNICAL DETAILS Purpose Compliance testing of Access Control Reader with stipulated standard Applicant / Client Certis Technology International Pte Ltd. Certis CISCO Centre 20, Jalan Afifi, Singapore 409179 Manufacturer Certis Technology International Pte Ltd. Certis CISCO Centre 20, Jalan Afifi, Singapore 409179 Laboratory performing the tests SIEMIC Nanjing (China) Laboratories NO.2-1,Longcang Dadao, Yuhua Economic Development Zone, Nanjing, China Tel:+86(25)86730128/86730129 Fax:+86(25)86730127 Email:[email protected] Test report reference number 11021322-FCC Date EUT received October 21, 2011 Standard applied FCC Part 15.207;15.209: 2011 Dates of test (from – to) November 13 to November 18, 2011 No of Units : #1 Equipment Category : DXX Trade Name : Certis Model : MP-8000 RF Operating Frequency (ies) : 125kHz(RFID) Number of Channels : 1 FCC ID : X3A-SMARFID Title: RF Test Report for …

Text truncated - open the document above for the full version.

Title: RF Test Report for Access Control Reader Model: MP-8000 To: FCC Part 15:2011 Serial#: 11021322-FCC Issue Date: November 21, 2011 Page: 26 of 34 www.siemic.com.cn Annex B.iii. Photograph: Test Setup Photo Front View of Radiated Emission Test Setup below 30MHz Rear View of Radiated Emission Test Setup below 30MHz Title: RF Test Report for Access Control Reader Model: MP-8000 To: FCC Part 15:2011 Serial#: 11021322-FCC Issue Date: November 21, 2011 Page: 27 of 34 www.siemic.com.cn Front View of Radiated Emission Test Setup above 30MHz Rear View of Radiated Emission Test Setup above 30MHz