A4B-ZC30SMART SWITCH

Smart Cord TM HOW IT WORKS The Smart Cord allows for manual or Bluetooth power control using the A2DP Bluetooth Profile of your device. If your device does not utilize this Stereo Bluetooth Profile, you will not be able to remotely control the switch. This is a very common and standard profile use by most Smartphones, including the top 10 as reviewed by PC Magazine in 2010. Because the Smart Cord uses the audio path to transmit signals, you must PLAY this audio file from a PAIRED Bluetooth Device to operate the switch. APPS exist for the various phone platforms. Please visit the website below for more information: www.ZMote.com/apps A web based app also exists that can be used with computers or other devices that do not have specifically design application. Also, because the Bluetooth command is sent via the audio channel, any A2DP capable Bluetooth device that can play audio files (mp3, wav, aif) may also function the Smart Cord. All that you need to do is download the audio file by visiting the website above, pair your device and play. For more information, please drop us an email or visit us online. ZMote Corporation www.ZMote.com [email protected] MANUAL POWER TOGGLE Push the Power Button to Toggle the Power of the Smart Cord. Bluetooth does not have to be on for this to work. Bluetooth Operation TURN ON BLUETOOTH Hold Down the Bluetooth Button for 5 seconds until Bluetooth Light flashes, indicating Bluetooth is On. TURN OFF BLUETOOTH Hold Down the Bluetooth Button for 10 seconds until Red Light Flashes Quickly and then turns off. DARK MODE With Bluetooth On, tap the Bluetooth Button. Bluetooth Light will then turn OFF. Tap the Bluetooth Button again to turn the Bluetooth Light back on. PAIRING 1. Hold Down the Bluetooth Button for 5 seconds until Bluetooth Light flashes. 2. DISCOVER Bluetooth Devices with your Phone or Similar device. 3. Connect to the Smart Cord identified ZCHORD1. 4. The Bluetooth Light will stop flashing and remain constant, indicating a connection has been made. For information on how to access your devices Bluetooth Connection process, please refer to the documentation associated with your Phone or similar device. FCC RF Exposure requirements: RF exposure information: To maintain compliance with FCC RF exposure requirements, use device that maintain a 20cm separation distance between the user's body and the host. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help

Date: Dec.1, 2011 To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 Re: ZMote Corporation FCC ID: A4B-ZC30 FCC Certification Confidentiality Request Gentlemen: This letter is to comply with 47 CFR 0.457 and 0.459 pertaining to confidentiality material. ZMote Corporation requests that the following documents regarding this submission for FCC ID: A4B-ZC30 be kept confidential: Exhibit Type File Name Block Diagram CONF APPENDIX A4B-ZC30_Block Diagram.pdf Schematics CONF APPENDIX A4B-ZC30_Schematics.pdf Operational Description CONF APPENDIX A4B-ZC30_Operational Description.pdf Part list CONF APPENDIX A4B-ZC30_BOM.pdf Those documents contain detailed system and equipment description and related information about the product which ZMote Corporation considers to be confidential proprietary, a custom design and, otherwise, not releasable to the general public. Since this design is a basis form which future technological products will evolve, ZMote Corporation considers this information would be of benefit to its competitors, and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Yours Sincerely, Arnold Goetzke President ZMote Corporation

External Photos

FCC ID: A4B-ZC30 Label Label Location

Internal Photos

FCC ID: A4B-ZC30 Page 1 of 2 Prediction of MPE limit at given distance Product Description: Smart Switch Type: ZC30 1. Introduction Equation from page 18 of OET Bulletin 65, Edition 97-01 Where: S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna 2. Limits for Maximum Permissible Exposure According to FCC Part 1.1307, systems operating under the provisions of this section shall be operated in a manner the ensures that the public is not exposed to radio frequency energy level in excess of the commission’s guidelines. According to FCC Part 1.1310 RF exposure is calculated. Limits for General Population/ Uncontrolled Exposure Limits for General Population/ Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength(E)(V/m) Magnetic Field Strength (H)(A/m) Power Density (S)(mW/cm 2 ) 0.3-1.34 614 1.63 (100)* 1.34-30 824/f 2.19/f (180/f2)* 30-300 27.5 0.073 0.2 300-1500 f/1500 1500-100,000 1.0 FCC ID: A4B-ZC30 Page 2 of 2 3. Test result Maximum peak output power at antenna input terminal(dBm) 0.002 Maximum peak output power at antenna input terminal(mW): 1.0 Prediction distance(cm): 20 Predication frequency(MHz): 2441 Antenna Gain (typical) (dBi): 4 Power density at predication frequency at 20 cm(mW/cm 2 ): 0.007 MPE limit for RF exposure at prediction frequency(mW/cm 2 ): 1 4. Conclusion The predicted power density level at 20cm is 0.007mw/cm 2 which is below the uncontrolled exposure limit of 1.0mw/cm 2 . The EUT is used at least 20cm away from user’s body. It is determined as mobile equipment and complied with the MPE limit.

SZ11100005W01 Page 2 of 71 DIRECTORY 1. GENERAL INFORMATION .................................................................................................... 3 1.1. EUT Description ....................................................................................................................... 3 1.2. Test Standards and Results ........................................................................................................ 4 1.3. Facilities and Accreditations ..................................................................................................... 5 2. 47 CFR PART 15C REQUIREMENTS .................................................................................... 6 2.1. Number of Hopping Frequency ................................................................................................ 6 2.2. Peak Output Power.................................................................................................................... 9 2.3. 20dB Bandwidth ..................................................................................................................... 16 2.4. Carried Frequency Separation ................................................................................................. 22 2.5. Time of Occupancy (Dwell time) ........................................................................................... 24 2.6. Conducted Spurious Emissions ............................................................................................... 31 2.7. Band Edge ............................................................................................................................... 42 2.8. Conducted Emission ............................................................................................................... 51 2.9. Radiated Emission................................................................................................................... 54 Change History Issue Date Reason for change 1.0 Nov 28, 2011 First edition SZ11100005W01 Page 3 of 71 1. General Information 1.1. EUT Description EUT Type ............................. : Smart Switch Serial No. .............................. : (n.a, marked #1 by test site) Hardware Version ................. : 1.0 Software Version .................. : Applicant .............................. : Manufacturer ........................ : 1.0 ZMote Corporation 1504 Westminster Place, Ann Arbor Michigan,USA Asia Winner Room 807, Building 12 QianLong Garden, Minzhi Avenue LongHua Town Shenzhen Frequency Range .................. : The frequency range used is 2402MHz - 2480MHz (79 channels, at intervals of 1MHz); The frequency block is 2400MHz to 2483.5MHz. Modulation Type .................. : Bluetooth: FHSS (GFSK(1Mbps), ∏/4-DQPSK(EDR 2Mbps), 8-DPSK(EDR 3Mbps)) Note 1: The EUT is a Smart Switch, it contains Bluetooth Module operating at 2.4GHz ISM band; the frequencies allocated for the Bluetooth Module is F(MHz)=2402+1*n (0<=n<=78). The lowest, middle, highest channel numbers of the Bluetooth Module used and tested in this report are separately 0 (2402MHz), 39 (2441MHz) and 78 (2480MHz). Note 2: For a more detailed description, please refer to Specification or User’s Manual supplied by the applicant and/or manufacturer. SZ11100005W01 Page 4 of 71 1.2. Test Standards and Results The objective of the report is to perform testing according to 47 CFR Part 15 Subpart C (Bluetooth, 2.4GHz ISM band radiators) for the EUT FCC ID Certification: No. Identity Document Title 1 47 CFR Part 15 (10-1-09 Edition) Radio Frequency Devices Test detailed items/section required by FCC rules and results are as below: No. Section in CFR 47Description Result 1 15.247(a) Number of Hopping Frequency PASS 2 15.247(b) Peak Output Power PASS 3 15.247(a) 20dB Bandwidth PASS 4 15.247(a) Carrier Frequency Separation PASS 5 15.247(a) Time of Occupancy (Dwell time) PASS 6 15.247(c) Conducted Spurious Emission PASS 7 15.247(c) Band Edge PASS 8 15.207 Conducted Emission PASS 9 15.209 15.247(c) Radiated Emission PASS NOTE: The tests were performed according to the method of measurements prescribed in DA-00-705. SZ11100005W01 Page 5 of 71 1.3. Facilities and Accreditations 1.3.1. Facilities Shenzhen Morlab Communications Technology Co., Ltd. Morlab Laboratory is a testing organization accredited by China National Accreditation Service for Conformity Assessment (CNAS) according to ISO/IEC 17025. The accreditation certificate number is L3572. All measurement facilities used to collect the measurement data are located at 3/F, Electronic Testing Building, Shahe Road, Xili, Nanshan District, Shenzhen, 518055 P. R. China. The test site is constructed in conformance with the requirements of ANSI C63.7, ANSI C63.4 and CISPR Publication 22; the FCC registration number is 741109. 1.3.2. Test Environment Conditions During the measurement, the environmental conditions were within the listed ranges: Temperature (°C): 15 - 35 Relative Humidity (%): 30 -60 Atmospheric Pressure (kPa): 86-106 SZ11100005W01 Page 6 of 71 2. 47 CFR Part 15C Requirements 2.1. Number of Hopping Frequency 2.1.1. Requirement According to FCC §15.247(a)(1)(iii), frequency hopping systems operating in the 2400MHz to 2483.5MHz bands shall use at least 15 hopping frequencies. 2.1.2. Test Description A. Test Setup: The Bluetooth Module of the EUT, which is powered by the Battery, is coupled to the Spectrum Analyzer (SA) and the Bluetooth Service Simulator (SS) with Attenuators through the Power Splitter; the RF load attached to the EUT antenna terminal is 50Ohm; the path loss as the factor is calibrated to correct the reading. During the measurement, the Bluetooth Module of the EUT is activated and controlled by the SS, and is set to operate under test mode transmitting 339 bytes DH5 packages at maximum power. B. Equipments List: Description Manufacturer Model Serial No. Cal. Date Cal. Due System Simulator R&S CMU200 100448 2011.05 1year Spectrum Analyzer Agilent E7405A US4…

Text truncated - open the document above for the full version.

Test Setup Photos 1. RSE 2. CSE 3.CE