A5W20120111BB001THandheld Digital Color Video Monitor - Transmitter

WARRANW INFORMATION For walranty.information see warranty information page. PRODUCT REGISTRATION To register your Bandit Buster@ product please visit: www. ba nditbuster.com/p rod uctreg istratio n A wRnrurruc Risk of electric shock Do not open back or remove front cover No user serviceable parts inside Keep out of reach of children PRODUCT FEATURES Receiver: . On/Off Switch (Left side of the unit) r AC jack (Left side of the unit) o Sound Light indicators (Front of the unit) . Volume controls (Front of the unit) . Power and Low Battery Indicator (Front of the Unit) r Transmitter Indicators "A" and "B" (Front of the unit) . Alarm+Vibrate, Vibrate, Alarm, Alert Options (Right side of the unit) . Earphone Jack (Right side of the unit) . Belt Clip (Back of the unit) r Kickstand (Back of the unit) . Reset Button (back of the unit) r Battery Compartment (Back of the unit) Transmitter: . Alarm/Silent Alarm Options (Left side of the unit) o Power Light Indicator ( Front) . PIR (passive infrared) (Front) . OfflON Power Switch (Right) . AC Jack (Right) r Battery Compartment (Back) .. r Transmitter Holster (Bottom) r Mounting Bracket (Back) BATTERY INSTALLATION This unit requires three (3) AA rechargeable batteries ; Turn the unit over and remove sliding battery cover from the back ofthe unit. r Insert the AA batteries into the battery compartment. . Replace battery cover onto unit. . CAUTION: Do not use alkaline batteries. . Bandit Buster@ recommends using quality rechargeable batteries ON LY. Ovlnerts Manual USING AC ADAPTERS . The unit can use standard 120v wall outlet, vehicle, boat, or RV AC plug-in. . To use the AC adapters, plug the connector on the cord into the AC adapter jack on the side of the unit. . Use only Bandit Buster@ adapters included in the unit. Do not use these adapters with any other device' r lf units do not work, make certain that the AC adapters are plugged into a working outlet. r lf electricity to the unit is lost, the unit will still operate via the rechargeable batteries for approximately 12-1 4 continuous hours. * Alert Options Earphone JACK Power and Low Battery lndicator Volume Transmitter lndicators "8" : \__/ \__/ \--l SETTING UP YOUR UNIT . Remove both units from the box and ensure both the transmitter(s) and receiver are set to ,,Off.,, o Remove the battery cover for the transmitter(s) using a Phillips screwdriver. . Remove the battery cover for the receiver by lowering the kickstand and remove the belt clip by spreading apart the sides of the clip to release it from the unit. Remove the battery cover using a Phillips screwdriver. r Install quality rechargeable A,A batteries to your units. DO NOT use alkaline batteries. o Replace the battery covers and reattach the belt clip. r Turn "On" both the transmitter(s) and the receiver. o The transmitte(s) will blink red and green until the unit is armed. This takes approximately 30 seconds. When the transmitter is armed the indicator light will stay solid green. o Set the transmitter(s) to either ',Alarm,, or ,,Silent.', Alarm lets the intruder know they are being monitored, while silent sounds no alarm and only alerts through the receiver. o Mount the transmitter(s) holster into desired location out of direct weather conditions. o Place the transmitter(s) in the holster. r Place your receiver where you can monitor sound activity, hear the PIR alarm, and/or see the sound bars. For best monitoring quality place the transmitter(s) and receiver facing one another, or as close to facing one another as possible. o You are now set up for real-time monitoring with Bandit Buster@. PAIRING THE UNITS . Units come paired from the factory. However, in the event that your units are not paired and ready for operation, follow these steps to pair your devices: o Turn both the receiver and the transmitter(s) ,Of+" then back "On." Wait for the indicator lights on the transmitter(s) to stop flashing. r For BB model 1941: '- Simultaneously hold the reset button on the back of the transmitter and the back of the receiver along with the Vol- button for approximately 4 seconds, - The receiver will flash green while your devices are pairing. - When pairing is complete your power indicator light will be solid green and your transmitter indicator light "A" will be solid yellow. - Your devices are paired dnd ready for operation. Owner's Manual r For BB model 1962: - Repeat steps for model number 1941 using the receiver and transmitter " A." - Your transmitter "A" is now paired, - To pair your transmitter "8" simultaneously hold the reset buttons on the back of the receiver, transmitter "B" and the Vol+ button. - The receiver will flash green while your devices are pairing. . - When the transmitter indicator light ,,8,, turns yellow and power indicator light is solid green your transmitter "B" is now paired and ready for operation. G ENERAL PRODUCT OPERATIONS o When the Bandit Buster@ is activated you will be able to instantly monitor your property through sound, sound light indicators, and PIR (passive infrared). o Sound monitoring is continuous. No alarm will sound unless the PIR detects motion. . When the PIR detects motion your receiver will alarm and/or vibrate. . Model 1962: Sound monitoring will continuously cycle between transmitter "A" and transmitter ,,8,, in 50 second increments. o lf either transmitter " A," or transmitter ,,B,, detects sound or the PIR of one of the transmitters detects motion, the receiver will instantly lock in to the transmitter where the sound or motion was detected. r To silence the receiver alarm, simultaneously hold the Vol- and Vol+ buttons for approximately two seconds. This does not deactivate the alarm; it only silences your receiver. . An alarm will sound for approximately 20 seconds. When the alarm stops, sound monitoring continues immediately. o The PIR will automatically reset within 30 seconds after the alarm is activated and turns off. * 2 BU$TE 1. 2. For a period of one (1) year from the date of pu…

Text truncated - open the document above for the full version.

2. TX Unit (Slave) U1 W55PA71 (MCU) MD1 MD7125PA (RF Module) U4 W25X40 (Flash Memory IC) Y1 12MHz Crystal Microphone U10 ISD8101X (Amplifier) PIR module (In Block 3) Speaker U5 Voltage Regulator U2 Voltage Regulator U3 Voltage Regulator Power Supply U8 Voltage Regulator 2404~2479MHz 3. PIR Module (Slave) U1 BISS0001 (MCU) JP2 Power Supply U2 Voltage Regulator PIR sensor JP1 To MCU A7125 2.4GHz FSK Transceiver Jul., 2011, v1.3AMICCOM Electronics Corporation 8 6. Block Diagram GIO1GIO2 SDIOBP_BG RFI RFO RFC CKO REGI VDD_VCO XI GND SCS VDD_D BP_RSSI SCK VDD_PLL VDD_A CPXO LNA VCOPAPLL MODEM Packet Handler BSP RXFIFO SPI 1 3 2 4 5 687910 15 13 14 12 11 2018191716 XOSC Regulator/ Thermal sensor Radio Control ADC TXFIFO Figure 6.1 A7125 Block Diagram

Allied Hill Enterprise Ltd. Suite 507 Tower 1, Silvercord 30 Canton Road, TST, Kowloon Hong Kong TEL: 852-2368-5328 FAX: 852-2722-5923 "I, an officer of Allied Hill Enterprise Ltd. do hereby authorize Intertek Testing Services (Mr. Terry Chan) to act on our behalf in front of the Federal Communications Commission with respect to all matters relating to certification of equipment under Part 15 and Part 18 of the FCC Rules until further notice." I further certify that no party (as defined in §1.2002(b) of CFR 47, 2004) to this application, including myself, is subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.,862. Dated this 7th day May of 2012 By Signature Simon Lee Printed Name Managing Director Title

INTERTEK TESTING SERVICE Report No.: HK12020934-1 FCC ID: A5W20120111BB001T Equipment Photographs Model: 08903 (External) INTERTEK TESTING SERVICE Report No.: HK12020934-1 FCC ID: A5W20120111BB001T Equipment Photographs Model: 33835 (External)

TX Unit (Slave) Size : 45 mm x 17 mm

INTERTEK TESTING SERVICE Report No.: HK12020934-1 FCC ID: A5W20120111BB001T Equipment Photographs Model: 08903 (Internal) INTERTEK TESTING SERVICE Report No.: HK12020934-1 FCC ID: A5W20120111BB001T Equipment Photographs Model: 08903 (Internal) INTERTEK TESTING SERVICE Report No.: HK12020934-1 FCC ID: A5W20120111BB001T Equipment Photographs Model: 08903 (Internal) INTERTEK TESTING SERVICE Report No.: HK12020934-1 FCC ID: A5W20120111BB001T Equipment Photographs Model: 08903 (Internal) INTERTEK TESTING SERVICE Report No.: HK12020934-1 FCC ID: A5W20120111BB001T Equipment Photographs Model: 08903 (Internal)

FCC ID: A5W20120111BB001T Technical Description: The brief circuit description is listed as follows: Main PCB board: MD1 and associated circuit act as 2.4GHz RF module (MD7125PA). U1 and associated circuit act as MCU. Y1 and associated circuit act as 12MHz oscillator of U1 U10 and associated circuit act as Amplifier. U2, U3, U5, U8 and associated circuit act as voltage regulator. U4 and associated circuit act as flash memory IC. PIR Module PCB board: U1 and associated circuit act as MCU. PIR and associated circuit act as sensor. U2 and associated circuit act as voltage regulator. Antenna Used: An internal, integral antenna has been used. Channel Separation: Channnel 8 9 10 11 12 13 14 15 Frequency (MHz) 2404 2404.5 2405 2405.5 2406 2406.5 2407 2407.5 Channnel 16 17 18 19 20 21 22 23 Frequency (MHz) 2408 2408.5 2409 2409.5 2410 2410.5 2411 2411.5 Channnel 24 25 26 27 28 29 30 31 Frequency (MHz) 2412 2412.5 2413 2413.5 2414 2414.5 2415 2415.5 Channnel 32 33 34 35 36 37 38 39 Frequency (MHz) 2416 2416.5 2417 2417.5 2418 2418.5 2419 2419.5 Channnel 40 41 42 43 44 45 46 47 Frequency (MHz) 2420 2420.5 2421 2421.5 2422 2422.5 2423 2423.5 Channnel 48 49 50 51 52 53 54 55 Frequency (MHz) 2424 2424.5 2425 2425.5 2426 2426.5 2427 2427.5 Channnel 56 57 58 59 60 61 62 63 Frequency (MHz) 2428 2428.5 2429 2429.5 2430 2430.5 2431 2431.5 Channnel 64 65 66 67 68 69 70 71 Frequency (MHz) 2432 2432.5 2433 2433.5 2434 2434.5 2435 2435.5 Channnel 72 73 74 75 76 77 78 79 Frequency (MHz) 2436 2436.5 2437 2437.5 2438 2438.5 2439 2439.5 Channnel 80 81 82 83 84 85 86 87 Frequency (MHz) 2440 2440.5 2441 2441.5 2442 2442.5 2443 2443.5 Channnel 88 89 90 91 92 93 94 95 Frequency (MHz) 2444 2444.5 2445 2445.5 2446 2446.5 2447 2447.5 Channnel 96 97 98 99 100 101 102 103 Frequency (MHz) 2448 2448.5 2449 2449.5 2450 2450.5 2451 2451.5 Channnel 104 105 106 107 108 109 110 111 Frequency (MHz) 2452 2452.5 2453 2453.5 2454 2454.5 2455 2455.5 Channnel 112 113 114 115 116 117 118 119 Frequency (MHz) 2456 2456.5 2457 2457.5 2458 2458.5 2459 2459.5 Channnel 120 121 122 123 124 125 126 127 Frequency (MHz) 2460 2460.5 2461 2461.5 2462 2462.5 2463 2463.5 Channnel 128 129 130 131 132 133 134 135 Frequency (MHz) 2464 2464.5 2465 2465.5 2466 2466.5 2467 2467.5 Channnel 136 137 138 139 140 141 142 143 Frequency (MHz) 2468 2468.5 2469 2469.5 2470 2470.5 2471 2471.5 Channnel 144 145 146 147 148 149 150 151 Frequency (MHz) 2472 2472.5 2473 2473.5 2474 2474.5 2475 2475.5 Channnel 152 153 154 155 156 157 158 Frequency (MHz) 2476 2476.5 2477 2477.5 2478 2478.5 2479 A7125 2.4GHz FSK Transceiver Jul., 2011, v1.3AMICCOM Electronics Corporation 1 Document Title A7125 Data Sheet, 2.4GHz FSK Transceiver with 2M / 1Mbps data rate Revision History Rev. No.HistoryIssue DateRemark 0.0Initial issue.Aug. 31, 2007Preliminary 0.1Logo change.Oct. 18, 2007Preliminary 0.2Modify PIN Configuration and Description, Block Diagram, Electrical Specifications, Diagram of State Machine. Add Control Register and Function Description. July 31, 2008Preliminary 0.3Add Power Saving FIFO Mode. Rename GPIO1 and GPIO2 into GIO1 and GIO2. August 31, 2008Preliminary 0.4Modify register recommended value IGFI [2:0] = [000] Modify register recommended value IGFQ [2:0] = [000] Delete TWWS function October 06, 2008Preliminary 0.5Modify register recommended value Delay Register I (17h): PDL= [000] Delay Register II (18h): WSEL= [011] Battery Detect Register (2Ch): QDS = [1] Crystal Test Register (32h): XCP= [00] IFAT Register (36h): IGFI [2:0] = [111], IGFQ [2:0] = [111] Modify PLL to WPLL settling time when PDL=[000] If LO is changed, from 20 us to 30 us If LO is fixed, from 20 us to 10 us Delete Ext Voltage Measurement function Add EOPD output to GIO2 Add PASW output to GIO2 Add EOPDS Register Add section 16.5 June 11, 2009Preliminary 1.0Modify register recommended value ADC Control (1Fh): CDM= [0] Modify recommended timing of PASW Feb., 2010Full Production 1.1Add Note 8 (regulator settling time) in chapter 8.Nov., 2010Full Production 1.2Change English Company NameNov. 30, 2010Full Production 1.3 Modify the tape reel information and the add Shenzhen office address. Jul. 2011 Full Production Important Notice: AMICCOM reserves the right to make changes to its products or to discontinue any integrated circuit product or service without notice. AMICCOM integrated circuit products are not designed, intended, authorized, or warranted to be suitable for use in life-support applications, devices or systems or other critical applications. Use of AMICCOM products in such applications is understood to be fully at the risk of the customer. A7125 2.4GHz FSK Transceiver Jul., 2011, v1.3AMICCOM Electronics Corporation 2 Table of Contents 1. Typical Application ..................................................................................................................................................... 5 2. General Description ................................................................................................................................................... 5 3. Feature ..................................................................................................................................................................... 5 4. PIN Configuration ...................................................................................................................................................... 6 5. PIN Description (I: Input, O: Output, I/O: Input or Output, G: Ground, D: Digital)........................................................... 7 6. Block Diagram ........................................................................................................................................................... 8 7. Absolution Maximum Rating ....................................................................................................................................... 9 8. Electrical Specifications................................................................…

Text truncated - open the document above for the full version.

1 2 3 4 5 6 ABCD 6 5 4 3 2 1 D CBA Title Number Revision Size C Date: 21-May-2012 Sheet of File: D:\JMEX\Feng\AH_SLA~11\AH_SLA~11.DDBDrawn By: /CSD0/WPGND DI CLK /HOLD VDD U4W25X40 C440.1uF DVDD33 GPB2GPB6 GPB7GPB5 C170.1uF C570.1uF C580.1uF C590.1uF C140.1uF C600.1uF LED1Power Red R34330 Y1 12MHz +/- 20ppm 2*6 R10 1M C4222pF C4122pF EX12M X12M EX12M X12M DVDD33 GPA5 R24 1M 1% R25 1.5M 1% GPA7 LED2Power Green R35330 GPA6 DVDD18 DVDD33 C340.1uF C320.1uF C614.7uF C180.1uF AH_Slave S1 Key GPB1R31470 DVDD33 VIN33 1 GND 2 GPIO2 4 GPIO1 5 SDIO 6 SCK 7 SCS 8 TX_SW 9 RX_SW 10 GND 11 CKO 3 VDD_PA 12 MD1MD7125PA RFVDD33 GPA12GPA13 GPB6GPB7GPB5GPB3GPB8GPB9 C477pF C517pF C527pF C457pF C467pF C537pF RFVDD33 C540.1uF 12 C7510uF/6.3V 12 C63 470uF/6.3V L74.7R 4.5V C560.1uF R211uF BAT1AAx3 4.5V J1DC_6V D21N4001 R371kR381K GPA15 Q5 B772 R2 2R0 1210 R1470 GPB1 Q3SI2301 DCin DCin C65470uF D1 1N4001 Q22N3904 4.5V R45 10K Bat+ D3 B0530W D4 2R0 1210 SW1SK23D03 R481K R501K R472K GPB10 C550.1uF Vin 1 GND 2 Vout 3 U8XC6206-3.0V SP1SPEAKER C251uF SPN 1 SPP 2 VSS 3 INN 4 VDD 8 CE 7 VREF 6 ACIN 5 U10 ISD8101X GPA10 4.5V R43 0R R414.7K L180R C40.1uF L140R C501uF R2320K R444.7K R221k C370.001uF ADAC0 L11FB C66 16V/100uF RFVSS C16 22uF/6.3V Vin 1 GND 2 Vout 3 U5XC6206-1.8V C67 47uF/16V Vin 1 GND 2 Vout 3 U2XC6206-3.0V AV_18 C100.1uF Vin 1 GND 2 Vout 3 U3XC6206-1.8V C70100uF AO_HPVSS33 1 AO_HPVSS33 2 AO_HPVDD33 3 AO_HPVDD33 4 USB_VDD33 5 USB_DP 6 USB_DM 7 USB_VSS33 8 PWMO0_ALT / UART_RX / GPB0 9 PWMO1_ALT / UART_TX / GPB1 10 SPI_SS0/GPB2 11 PWMO0 / SPI_SS1 / GPB3 12 WPMO1 / VISCLK / GPB4 13 VSS_IO33 15 SPI_SO / VI_CLK / GPB5 16 SPI_SI / VIVsync / GBP6 17 CapCH0 / VID0 / GPB8 19 CapCH1 / VID1 / GPB9 20 VDD18 21 VSS18 22 PWMC00 / VID2 / GPB10 23 VDD_IO33 24 EXTAL 25 XTAL 26 VSS_IO33 27 PWMC01 / VID3 / GPB11 28 PWMC02 / VID4 / GPB12 29 PWMC10 / VID5 / GPB13 30 PWMC11 / VID6 / GPB14 31 PWMC12 / VID7 / GPB15 32 VDD18 33 VSS18 34 TEST 35 TDO 36 TDI 37 TMS 38 PLLVSS18D 39 PLLVDD18D 40 PLLVSS18A 41 PLLVDD18A 42 VDD_IO33 14 SPI_CLK / VIHsync / GPB7 18 GND 0 nTRST 43 TCK 44 nRESET 45 nWAIT 46 nOE 47 VDD_IO33 48 EXTAL32K 49 XTAL32K 50 VSS_IO33 51 nECS0 52 nSCS1 / nRCS2 53 nBTCS 54 nSCS0 / nRCS1 55 VDD_18 56 VSS_18 57 nWBE0 / nSDQM0 58 VDD_IO33 59 VSS_IO33 60 nWBE1 / nSDQM1 61 MCKE 62 nSWE 63 nSRAS 64 nSCAS 65 VDD_IO33 66 MCLK 67 VSS_IO33 68 MA0 69 MA1 70 MA2 71 VDD_18 72 VSS_18 73 MA3 74 MA4 75 MA5 76 MA6 77 VDD_IO33 78 VSS_IO33 79 MA7 80 MA8 81 MA9 82 MA10 83 MA11 84 MA12 85 MA13 86 MA14 87 MA15 88 VDD_IO33 89 VSS_IO33 90 MA16 91 MA17 92 MA18 93 MA19 94 MA20 95 VDD_18 96 VSS_18 97 MA21 98 MD0 99 MD1 100 MD2 101 VDD_IO33 102 VSS_IO33 103 MD3 104 MD4 105 MD5 106 MD6 107 VDD_18 108 VSS_18 109 MD7 110 MD8 111 MD9 112 MD10 113 MD11 114 VDD_IO33 115 VSS_IO33 116 MD12 117 MD13 118 MD14 119 MD15 120 ADC_VDD33 121 AVO3 122 AVO2 123 AVO1 124 AVO0 125 ADC_REFP 126 ADC_REFN 127 ADC_VSS33 128 GPA0 / ALT_VICLK 129 GPA1 / ALT_VIVsync] 130 GPA2 / ALT_VIH sync 131 GPA3 / nECS2 132 VDD_IO33 133 VSS_IO33 134 GPA4 / USB_DET 135 GPA5 136 GPA6 137 GPA7 / LVDIN 138 GPA8 / SD_DAT0 139 GPA9 / SD_DAT1 140 VDD_18 141 VSS_18 142 GPA10 / SD_DATA2 143 VDD_IO33 144 VSS_IO33 145 GPA11 / SD_DATA3 146 GPA12 / SD_CMD 147 VDD_18 148 VSS_18 149 GPA13 / SD_CLK 150 GPA14 / SD_CD 151 GPA15 / nECS1 152 VSS_ADC1 153 CAPP 154 CAPN 155 VREF_ADC 156 VDD18_ADC1 157 MICN 158 MICP 159 VDD18_ADC2 160 VSS_ADC2 161 AO_AVDD18 162 AO_AVDD18 163 AO_VREF 164 AO_AVSS 165 AO_AVSS 166 ADAC1 167 ADAC1 168 ADAC0 169 ADAC0 170 U1W55PA71_DICE ADC_18 C192.2uF C50.1uF ADAC0 ADAC1 L1 4.7R L5 4.7R ADC_VSS ADC_VSS C10.1uF C1322uF PVDD33 PVDD33 DVDD33 VDD33 VDD33 C330.1uF DVDD18 GPA15 GPA14 GPA13 GPA10 DVDD33 C211uF C240.1uF DVDD18 GPA11 GPA12 GPA8 GPA9 GPA4 GPA5 GPA6 GPA7 GPA0 GPA1 GPA2 GPA3 C641K C200.1uF C120.1uF C110.1uF C15NC C351K DVDD33 R2910K R2810KR2710KR2610K DVDD33 Cr1uF R9 100K nTCK nTRST 1 JI 1 J2 1 J5 1 J3 1 J4 1 J6 1 J7 GPB11GPB12GPB13GPB14GPB15EX12MX12MGPB5GPB6GPB7GPB8GPB9GPB10GPB0GPB1GPB2GPB3GPB4 L3 0R L2 0R C30.1uF AVDD_18 ADCVDD_18 R1420K 4.5V GPB15 SW2SK23D03 R3220K VDD33 GPB4 L4 33R C103NC C104NC M1MICHEADERDIP2X1-2.0MM R33.6K C31 0.22u R43.6K C30 0.22u MICPMICN MIC1MIC2 R7 470R C20.1u MIC+MIC- MICPMICN VDD33 ADC_VSS18 ADC_VSS18 Q12N3906 R19100K GPA11 R2010K C6816V/100F C29 22uF R6 0R C7102 C8 102 L13 FB L12 FB R1147K V0 12 PIRJ2To PIR Module JP2 12 PIRJ1To PIR Module JP1 1 2 3 4 ABCD 4 3 2 1 D CBA Title Number Revision Size A4 Date: 21-May-2012 Sheet of File: D:\JMEX\Feng\PIR_MO~11\PIR_MO~11.DDBDrawn By: R247kR6100k R147k 123 SEN1PIR EC1100uF R7 47k C2473 A 1 VO 2 RR1 3 RC1 4 RC2 5 RR2 6 VSS 7 VREF 8 VC 9 IB 10 VDD 11 OUT2 12 IN2- 13 IN1+ 14 IN1- 15 OUT1 16 U1BISS0001 R5100kR8CDS R3 100K R101M R4100K R15 1K EC422uF C3 103 R9 1.2M C12000p R11 1M OUT R13 510k C4100P C5102 R12 510k SW1 SOLD EC3 22uF VDD VDD EC24.7uF R14NC d14148 C71uF R1747k C6 103 R16100k VDD C90.1u VCC VCC 12 JP12PIN VCC R36510K Vin 1 GND 2 Vout 3 U2XC6206-3.0V 12 JP22PIN PIR_MODULE V2 A7125 2.4GHz FSK Transceiver Jul., 2011, v1.3AMICCOM Electronics Corporation 86 19. Application Circuit Example Below are AMICCOM’s ref. design module, MD7125-A04, circuit example and its PCB layout. C11 3.9pF C12 3.9pF C2 1nF C3 100pF L4 1.2nH C5 100pF VDD_A C6 0.1uF R1 2.7k C14 2.2nF C1 6 180pF C7 0.1uF 12 Y1 16MHz C17 33pF C18 27p F C10 2.2uF SDIO SCK SCS C4 4.7uF VDD_ACKOGIO2GIO1 L5 2.2nH REGI C9 2.2uF L3 1.5nH VDD_A SCS SCKSDIO GIO1GIO2 GNDREGI 12 34 56 78 J1 HEADER 4X2A/2.54 C15 1pF ANT BP_RSSI 1 BP_BG 2 RFI 3 RFC 5 RFO 4 V DD_VCO 6 CP 7 VDD_PLL 8 XI 9 XO 10 GND 15 SCS 11 SCK 12 SDI O 14 VDD_D 13 CKO 18 GIO2 17 GIO1 16 REGI 19 VDD_A 20 A7125P KG U1 A7 1 25 PK G C8 1pF L1 2.7nH C19 100pF R2 NC C1 NC C13 1pF 1. A7125 schematic for RF layouts with single ended 50ȍ RF output. 2. C17 and C18 must be matched to the crystal’s load capacitance, Cload. Please see application note for detail.

INTERTEK TESTING SERVICES Report No.: HK12020934-1 Sample No.:1/3 Code: FCC15C_f / Effective Date: 24 Jun 2011 ( of ) Average Factor Plot – Pursuant to FCC Part 15 Section 15. 249 Requirement (Pass/Fail) INTERTEK TESTING SERVICES Report No.: HK12020934-1 Sample No.:1/3 Code: FCC15C_f / Effective Date: 24 Jun 2011 ( of ) Average Factor Plot – Pursuant to FCC Part 15 Section 15. 249 Requirement (Pass/Fail) INTERTEK TESTING SERVICES Report No.: HK12020934-1 Sample No.:1/3 Code: FCC15C_f / Effective Date: 24 Jun 2011 ( of ) Average Factor Plot – Pursuant to FCC Part 15 Section 15. 249 Requirement (Pass/Fail) INTERTEK TESTING SERVICES Report No.: HK12020934-1 Sample No.:1/3 Code: FCC15C_f / Effective Date: 24 Jun 2011 ( of ) The duration of one cycle = 100ms Effective period of the cycle = 1.1ms x 4 + 160us x 4 + 140us x 2 DC = 5.32/100 The averaging factor is found by 20log 0.0532 = -25.5dB. Average Factor Plot – Pursuant to FCC Part 15 Section 15. 249 Requirement (Pass/Fail)

INTERTEK TESTING SERVICES Report No.: HK12020934-1 Sample No.:1/3 Code: FCC15C_f / Effective Date: 24 Jun 2011 ( of ) Bandedge Plot – Pursuant to FCC Part 15 Section 15. 249 Requirement (Pass/Fail) OATS = 111.10 dBuV/m Field Stregth (Peak) = 111.10 – 44.89 dBuV/m = 66.21 dBuV/m (Limit: 74 dBuV/m) Field Stregth (Average) = 66.21 – AF dBuV/m = 66.21 – 25.50 dBuV/m = 40.71 dBuV/m (Limit: 54 dBuV/m) OATS = 110.80 dBuV/m Field Stregth (Peak) = 110.80 – 46.10 dBuV/m = 64.70 dBuV/m (Limit: 74 dBuV/m) Field Stregth (Average) = 64.70 – AF dBuV/m = 64.70 – 25.50 dBuV/m = 39.20 dBuV/m (Limit: 54 dBuV/m)

Report no.: HK12020934-1 FCC ID: A5W20120111BB001T 150 kHz30 MHz 1 PK CLRWR 2 AV CLRWR SGL TDS 6DB dBμV dBμV AC RBW 9 kHz MT 1 s PREAMP OFFAtt 10 dB AUTO 1 MHz10 MHz 0 10 20 30 40 50 60 70 80 90 100 CF15MAV CF15MQP Date: 22.MAR.2012 12:18:46 Report no.: HK12020934-1 FCC ID: A5W20120111BB001T EDIT PEAK LIST (Final Measurement Results) Trace1: CF15MQP Trace2: CF15MAV Trace3: --- TRACE FREQUENCY LEVEL dBμV DELTA LIMIT dB 1 Quasi Peak 370.5 kHz 28.75 L1 -29.73 1 Quasi Peak 496.5 kHz 25.89 L1 -30.16 1 Quasi Peak 672 kHz 31.50 L1 -24.49 1 Quasi Peak 1.0185 MHz 26.70 L1 -29.29 1 Quasi Peak 1.2975 MHz 31.06 L1 -24.94 1 Quasi Peak 1.554 MHz 29.31 L1 -26.68 1 Quasi Peak 2.328 MHz 27.35 L1 -28.64 1 Quasi Peak 4.785 MHz 33.87 L1 -22.13 Date: 22.MAR.2012 12:18:25

- The test report only allows to be revised within the retention period unless further standard or the requirement was noticed. - This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Hong Kong Ltd. 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong. Tel: (852) 2173 8888 Fax: (852) 2785 5487 Website: www.hk.intertek-etlsemko.com TEST REPORT Report No.: HK12020934-1(R1) Allied Hill Enterprise Ltd. Application For Certification (Original Grant) (FCC ID: A5W20120111BB001T) Transceiver Supersede Report No. HK12020934-1 Dated 25 May 2012 Prepared and Checked by: Approved by: Signed On File Kung Wing Cheong, Steven Engineer Lau Chin Yu, Benny Lead Engineer Date: May 30, 2012 INTERTEK TESTING SERVICES Report No.: HK12020934-1(R1) FCC ID: A5W20120111BB001T i GENERAL INFORMATION Allied Hill Enterprise Ltd. BRAND NAME: Bandit Buster, MODEL: N/A FCC ID: A5W20120111BB001T Grantee: Allied Hill Enterprise Ltd. Grantee Address: Suite 507, Tower 1 Silvercord, 30 Canton Raod, Tsim Sha Tsui, Kowloon, Hong Kong. Contact Person: Mr. Alex Leung Tel: (852) 2368 5328 Fax: (852) 2722 5923 e-mail: N/A Manufacturer: N/A Manufacturer Address: N/A Brand Name: Bandit Buster Model: N/A Type of EUT: Transciever Description of EUT: Security and surveillance system Serial Number: N/A FCC ID : A5W20120111BB001T Date of Sample Submitted: February 23, 2012 Date of Test: May 11, 2012 Report No.: HK12020934-1(R1) Report Date: May 30, 2012 Environmental Conditions: Temperature: +10 to 40°C Humidity: 10 to 90% INTERTEK TESTING SERVICES Report No.: HK12020934-1(R1) FCC ID: A5W20120111BB001T ii SUMMARY OF TEST RESULT Allied Hill Enterprise Ltd. BRAND NAME: Bandit Buster, MODEL: N/A FCC ID: A5W20120111BB001T TEST SPECIFICATION REFERENCE RESULTS Maximum Peak Output Power 15.247(b), (c) / RSS-210 A8.4 N/A Hopping Channel Carrier Frequencies Separation (for 2.4GHz Digital) 15.247(e) / RSS-210 A8.1 N/A 20dB Bandwidth of the Hopping Channel 15.247(a) / RSS-210 A8.1 N/A Number of Hopping Frequencies 15.247(e) / RSS-210 A8.1 N/A Average Time of Occupancy of Hopping Frequency 15.247(e) / RSS-210 A8.1 N/A Anteann Conducted Spurious Emissions 15.247(d) / RSS-210 A8.5 N/A Radiated Spurious Emissions 15.247(d) / RSS-210 A8.5 N/A RF Exposure Compliance 15.247(i) / RSS-Gen 5.5 N/A Transmitter Power Line Conducted Emissions 15.207 / RSS-Gen 7.2.2 N/A Transmitter Field Strength (for 27MHz) 15.227 / RSS-310 3.8 N/A Transmitter Field Strength (for 40MHz) 15.229 / RSS-210 A2.7 N/A Transmitter Field Strength, Bandwidth and Timing Requirement (for Remote Control) 15.231(a) / RSS-210 A1.1.1 N/A Transmitter Field Strength, Bandwidth and Timing Requirement (for 433MHz) 15.231(e) / RSS-210 A1.1.5 N/A Transmitter Field Strength and Bandwidth Requirement(for 88-108MHz) 15.239 / RSS-210 A2.8 N/A Transmitter Field Strength and Bandwidth Requirement(for 902- 928MHz or 2.4GHz) 15.249 / RSS-210 A2.9 Pass Transmitter Field Strength and Bandwidth Requirement (for 49MHz) 15.235 / RSS-310 3.9 N/A Receiver / Digital Device Radiated Eissions 15.109 / ICES-003 N/A Digital Device Conducted Emissions 15.107 / ICES-003 N/A Note: 1. The EUT uses a permanently attached antenna which, in accordance to section 15.203, is considered sufficient to comply with the pervisions of this section. 2. Pursuant to FCC part 15 Section 15.215(c), the 20 dB bandwidth of the emission was contained within the frequency band designated (mentioned as above) which the EUT operated. The effects, if any, from frequency sweeping, frequency hopping, other modulation techniques and frequency stability over excepted variations in temperature and supply voltage were considered. INTERTEK TESTING SERVICES Report No.: HK12020934-1(R1) FCC ID: A5W20120111BB001T iii Table of Contents 1.0 General Description............................................................................................ 1 1.1 Product Description ............................................................................................... 1 1.2 Related Submittal(s) Grants................................................................................... 1 1.3 Test Methodology.................................................................................................. 1 1.4 Test Facility ........................................................................................................... 2 2.0 System Test Configuration ................................................................................. 2 2.1 Justification ........................................................................................................... 2 2.2 EUT Exercising Software....................................................................................... 2 2.3 Special Accessories .............................................................................................. 2 2.4 Equipment Modification ......................................................................................... 2 2.5 Measurement Uncertainty...................................................................................... 3 2.6 Support Equipment List and Description ........…

Text truncated - open the document above for the full version.

INTERTEK TESTING SERVICE Report No: HK12020934-1 FCC ID: A5W20120111BB001T i Configuration Photographs Worst-Case Line-Conducted Emissions (Front View) Model : 08903 INTERTEK TESTING SERVICE Report No: HK12020934-1 FCC ID: A5W20120111BB001T ii Configuration Photographs Worst-Case Line-Conducted Emissions (Back View) Model : 08903 INTERTEK TESTING SERVICE Report No: HK12020934-1 FCC ID: A5W20120111BB001T iii Configuration Photographs Worst-Case Line-Conducted Emissions (Side View) Model : 08903

INTERTEK TESTING SERVICE Report No: HK12020934-1 FCC ID: A5W20120111BB001T Configuration Photographs Worst-Case Radiated Emissions (Front View) Model: 08903 HK12020934-1 INTERTEK TESTING SERVICE Report No: HK12020934-1 FCC ID: A5W20120111BB001T Configuration Photographs Worst-Case Radiated Emissions (Back View) Model: 08903 HK12020934-1