AK8CUHZCT1AWireless Controller

DUALSHOCK ® 4 Wireless Controller Instruction Manual CUH-ZCT1U ENGLISH About the DUALSHOCK ® 4 Wireless Controller Before using this product, carefully read this manual and any manuals for compatible hardware. Retain instructions for future reference. For assistance with this product, visit www.us.playstation.com or call SCEA Consumer Services at 1-800-345-7669. Battery life and duration • Do not handle damaged or leaking lithium-ion batteries. • The battery has a limited life span. Battery duration will gradually decrease with repeated usage and age. Battery life also varies depending on the storage method, conditions of use and environmental factors. • Charge in an environment where the temperature range is between 10°C - 30°C (50°F - 86°F). Charging may not be as effective when performed in other environments. • When the wireless controller is not used for an extended period of time, it is recommended that you fully charge it at least once a year to help maintain battery functionality. Use and handling precautions • Avoid prolonged use of this product. Take a break at about 30 minute intervals. • Stop using this unit immediately if you begin to feel tired or if you experience discomfort or pain in your hands or arms during use. If the condition persists, consult a doctor. • Permanent hearing loss may occur if the headset or headphones are used at high volume. Set the volume to a safe level. Over time, increasingly loud audio may start to sound normal but can actually be damaging your hearing. If you experience ringing or any discomfort in your ears or muffled speech, stop listening and have your hearing checked. The louder the volume, the sooner your hearing could be affected. To protect your hearing: - Limit the amount of time you use headset or headphones at high volume. - Avoid raising the volume to block out noisy surroundings. - Lower the volume if you can’t hear people speaking near you. • Avoid looking into the light bar of the controller when it is flashing. Stop using the controller immediately if you experience any discomfort or pain in any body parts. • This product is intended for use with the hands only. • The vibration function of this product may aggravate injuries. Do not use the vibration function if you have any ailment or injury to the bones, joints, or muscles of your hands or arms. • Note that some software titles enable the vibration function by default. To disable the vibration function, select (Settings) ➡ [Devices] ➡ [Controllers] from the function screen, and then remove the checkmark from [Enable Vibration]. • Do not expose the product to high temperatures, high humidity or direct sunlight. • Do not allow the product to come into contact with liquids. • Do not put heavy objects on the product. • Do not throw or drop the product or subject it to strong physical shock. • When using the motion sensor function, be cautious of the following points. If the controller hits a person or object, this may cause accidental injury or damage. - Before using, check that there is plenty of space around you. - When using the controller, grip it firmly to make sure it cannot slip out of your hand. - If using a controller that is connected to the PlayStation ® 4 system with a USB cable, make sure there is enough space for the cable so that the cable will not hit a person or object. Also, take care to avoid pulling the cable out of the PS4™ system while using the controller. Exterior protection Follow the instructions below to help prevent the product exterior from deteriorating or becoming discolored. • Do not place any rubber or vinyl materials on the product exterior for an extended period of time. • Use a soft, dry cloth to clean the product. Do not use solvents or other chemicals. Do not wipe with a chemically-treated cleaning cloth. Registering (pairing) the controller The first time you use the controller, or when you want to use the controller on another PlayStation ® 4 system, you must perform device registration (pairing). Turn on the PS4™ system and connect the controller to the system with the USB cable to complete device registration. To a USB port on the PS4™ system. USB cable (supplied with the PS4™ system) HINT For details on using the controller, refer to the user’s guide of the PS4™ system. End of Life Product Recycling The DUALSHOCK ® 4 wireless controller contains a lithium ion battery. Follow local regulations when disposing of the system. Sony products can be recycled for free in the United States and Canada by dropping the product off at a number of nationwide locations. Visit sony.com/ecotrade and eco.sony.ca for details. FCC and IC Notice This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that are deemed to comply without testing of specific absorption rate (SAR). This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipm…

Text truncated - open the document above for the full version.

A AK8CUHZCT1A 409B-CUHZCT1A Label X-XXX-XXX-XX XX Factory CodeG:GoerTek F1:Foxcon Yantai F2:Foxconn Guiyang 0990-15-6223 Label Location Label

Wireless Block Picture of Wireless Block Bluetooth Antenna

UL Japan, Inc. Ise EMC Lab 4383-326 Asama-cho, Ise-shi, Mie 516-0021 Japan T:: +81.596.24.8999 / F:: +81.596.24.8124 / W:: ul.com/jp March 26, 2015 UL VERIFICATION SERVICES, INC 47173 Benicia Street, Fremont, CA 94538 FCC ID: AK8CUHZCT1A To whom it may concern, We, UL Japan, Inc, hereby declare that Wireless Controller, model: CUH-ZCT1U (FCC ID: AK8CUHZCT1A) of Sony Computer Entertainment Inc. is exempt from RF exposure SAR evaluation as its output power meets the exclusion limits stated in KDB 447498D01(v05r02). KDB 447498D01(v05r02) has the following exclusion for portable devices: The 1g and 10g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where •f(GHz) is the RF channel transmit frequency in GHz •Power and distance are rounded to the nearest mW and mm before calculation •The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. This device has f = 2.48 GHz and distance = 5 mm (minimum separation distance: 5mm was used in the calculation) and the maximum average output power was 1 mW So for this device: 1 mW[maximum average output power]/5 mm[minimum separation distance]*√2.48 = 0.3 *This is less than 3.0, so no SAR is required. Even taking into account the tolerance, this device can be satisfied with the limits. Thank you for your attention to this matter. Masanori Nishiyama Manager of Ise EMC Lab. Consumer Technology Division UL Japan, Inc.

Test report No. : 10682751H-A Page : 1 of 54 Issued date : March 17, 2015 FCC ID : AK8CUHZCT1A UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 13-EM-F0429 RADIO TEST REPORT Test Report No. : 10682751H-A Applicant : Sony Computer Entertainment Inc. Type of Equipment : Wireless Controller Model No. : CUH-ZCT1U FCC ID : AK8CUHZCT1A Test regulation: FCC Part 15 Subpart C: 2015 Test Result : Complied 1. This test report shall not be reproduced in full or partial, without the written approval of UL Japan, Inc. 2. The results in this report apply only to the sample tested. 3. This sample tested is in compliance with the above regulation. 4. The test results in this report are traceable to the national or international standards. 5. This test report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. 6. This test report covers Radio technical requirements. It does not cover administrative issues such as Manual or non-Radio test related Requirements. (if applicable) Date of test: February 23 to March 10, 2015 Representative test engineer: Takumi Shimada Engineer Consumer Technology Division Approved by: Masanori Nishiyama Manager Consumer Technology Division NVLAP LAB CODE: 200572-0 This laboratory is accredited by the NVLAP LAB CODE 200572-0, U.S.A. The tests reported herein have been performed in accordance with its terms of accreditation. *As for the range of Accreditation in NVLAP, you may refer to the WEB address, http://www.ul.com/japan/jpn/pages/services/emc/about/ma rk1/index.jsp#nvlap Test report No. : 10682751H-A Page : 2 of 54 Issued date : March 17, 2015 FCC ID : AK8CUHZCT1A UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 REVISION HISTORY Original Test Report No.: 10682751H-A Revision Test report No. Date Page revised Contents - (Original) 10682751H-A March 17, 2015 - - Test report No. : 10682751H-A Page : 3 of 54 Issued date : March 17, 2015 FCC ID : AK8CUHZCT1A UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 CONTENTS PAGE SECTION 1: Customer information ......................................................................................................... 4 SECTION 2: Equipment under test (E.U.T.) ........................................................................................... 4 SECTION 3: Test specification, procedures & results ............................................................................ 5 SECTION 4: Operation of E.U.T. during testing .................................................................................... 8 SECTION 5: Conducted Emission .......................................................................................................... 10 SECTION 6: Radiated Spurious Emission ............................................................................................ 11 SECTION 7: Antenna Terminal Conducted Tests ................................................................................ 12 APPENDIX 1: Data of EMI test .............................................................................................................. 13 Conducted Emission ......................................................................................................................... 13 20dB Bandwidth and Carrier Frequency Separation ......................................................................... 17 Number of Hopping Frequency ........................................................................................................ 20 Dwell time ......................................................................................................................................... 22 Maximum Peak Output Power .......................................................................................................... 25 Radiated Spurious Emission ............................................................................................................. 27 Conducted Spurious Emission .......................................................................................................... 34 Conducted Emission Band Edge compliance ................................................................................... 46 99%Occupied Bandwidth ................................................................................................................. 48 APPENDIX 2: Test instruments ............................................................................................................. 50 APPENDIX 3: Photographs of test setup ............................................................................................... 51 Conducted Emission ......................................................................................................................... 51 Radiated Spurious Emission ............................................................................................................. 52 Worst Case Position (Horizontal: Z-axis/ Vertical:Y-axis) .............................................................. 53 Test Configuration and peripherals ................................................................................................... 54 Test report No. : 10682751H-A Page : 4 of 54 Issued date : March 17, 2015 FCC ID : AK8CUHZCT1A UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 SECTION 1: Customer information Company Name Sony Computer Entertainment Inc. Brand Name SONY Address 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Japan Telephone Number +81-3-6748-6333 Facsimile Number +81-3-6748-6383 Contact Person Kiyoto Sasaki SECTION 2: Equipment under test (E.U.T.) 2.1 Identification …

Text truncated - open the document above for the full version.

Test report No. : 10682751H-A Page : 51 of 54 Issued date : March 17, 2015 FCC ID : AK8CUHZCT1A UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 APPENDIX 3: Photographs of test setup Conducted Emission Photo 1 Photo 2 Test report No. : 10682751H-A Page : 52 of 54 Issued date : March 17, 2015 FCC ID : AK8CUHZCT1A UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 Radiated Spurious Emission Photo 1 Photo 2 Test report No. : 10682751H-A Page : 53 of 54 Issued date : March 17, 2015 FCC ID : AK8CUHZCT1A UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 Worst Case Position (Horizontal: Z-axis/ Vertical:Y-axis) X-axis Y-axis Z-axis Test report No. : 10682751H-A Page : 54 of 54 Issued date : March 17, 2015 FCC ID : AK8CUHZCT1A UL Japan, Inc. Ise EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 Test Configuration and peripherals *Cabling and setup were taken into consideration and test data was taken under worse case conditions. Description of EUT and Support equipment No Item Model number Serial number Manufacturer Remarks A Wireless Controller CUH-ZCT1U 00226 for AT* 00238 for other tests Sony Computer Entertainment EUT B Laptop PC 2324A82(7P) R9-W6R36 for AT* R9-X86LK for other tests Lenovo - C AC Adapter 45N0121 11S45N012Z1ZHXU2C B96T Lenovo - D Mouse M-UB48 LZE02650788 Logitech - E IN-EAR HEAD SET - - Sony Computer Entertainment - F Test Jig - - Sony Computer Entertainment - *AT: Antenna Terminal Conducted test List of cables used No Name Length (m) Shield Remarks Cable Connector 1 USB Cable 1.5 Shielded Shielded - 2 DC Cable 1.8 Shielded Shielded - 3 AC Cable 1.0 Unshielded Unshielded - 4 USB Cable 0.8 Shielded Shielded - 5 IN-EAR HEAD SET Cable 1.2 Shielded Shielded - End of Report B C 2 3 E 5 A F 4 1 D : Ferrite Core (Standard Attachment) AC 120V/60Hz