AK8PCWADE505.0 GHz WLAN Converter - UNII

4-669-393-11(1) Sony Corporation  2003 Printed in Japan PCWA-DE50 Read This First WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Owner’s Record The model and serial numbers are located on the back of the product. Record the serial number in the space provided below. Refer to them whenever you call your Sony dealer regarding this product. Model No. PCWA-DE50 Serial No.______________ CAUTION You are cautioned that any changes or modifications not expressly approved in this manual could void your warranty. Exposure to Radio Frequency Radiation. The radiated output power of the Wireless LAN Converter is far below the FCC radio frequency exposure limits. Nevertheless, the Wireless LAN Converter shall be used in such a manner that the potential for human contact during normal operation is minimized. FCC Radio-Frequency Exposure Statement This equipment generates and radiates radio- frequency energy. In order to comply with FCC radio-frequency radiation exposure guidelines for an uncontrolled environment, this equipment has to be installed and operated while maintaining a minimum body to antenna distance of 20 cm. Based on continuous exposure of 30 minutes. Users are not permitted to make changes or modify the system in any way. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to television reception, which can be determined by turning the equipment off and Safety Information WARNING • Opening the unit, for whatever reason, could lead to damage that is not covered by the warranty. • Do not touch the device or accessories during thunderstorms. Electrical shock could result. • This device is made for use in the USA only. • For indoor use only. • Do not use this equipment on hospital premises. Doing so may cause medical devices to malfunction. • Do not use this equipment in an aircraft, as doing so could cause the aircraft's equipment to malfunction. • While using the Wireless LAN Converter, do not cover it or turn it on its side. Do not cover the Wireless LAN Converter with objects such as magazines or newspapers or use it in confined, enclosed places, such as the spaces between walls and furniture. Furthermore, do not turn the Wireless LAN Converter on its side while using it. Either situation could cause heat to build up inside the Wireless LAN Converter, leading to overheating and possible fire. • Carefully place the Ethernet cable. Personal injury or damage to the Wireless LAN Converter could result from people tripping over the Ethernet cable, Wireless Unit cable, Power Unit, or power cord. Protect wiring by locating it in places where people do not walk. • Do not swing the Wireless LAN Converter. Injury could result if the adapter strikes a person or fragile material, such as glass. • Keep the Wireless LAN Converter out of the reach of children. Unforeseeable injury could result from swallowing loose parts, etc. • Place the Wireless LAN Converter on a stable surface. Do not place the Wireless LAN Converter on wobbly or tilted surfaces. Tipping or falling could result in injury. • When using wall mounting, make sure that the wall is strong enough to support the Wireless Unit. The Wireless Unit could fall if the wall is not strong enough, leading to unforeseeable accidents. Further, be careful not to drop the unit or the tools used for mounting it. Doing so could result in unforeseeable accidents. • Avoid locations that are directly exposed to sunlight or heaters. Internal overheating could result in fire or damage to the unit. • Make sure connectors are properly connected. – Do not insert any metallic objects inside the connectors. Short-circuiting the pins could cause fire or damage to the unit. – Be careful to insert connectors squarely. Crooked insertion could cause pins to short- circuit, possibly causing fire or damage to the unit. • Use only the supplied Power Unit with your Sony Wireless LAN Converter. To disconnect your Wireless LAN Converter from the power supply, unplug the Power Unit. • ISDN and telephone lines cannot be connected to the Wireless Unit connector and/or NETWORK connector of the Power Unit. If the Power Unit is connected to the network or telephone lines mentioned below, high electric current to the connectors may cause damage, overheating or fire. Connecting to home or business-use telephone lines is strictly prohibited. – Telephone lines – PBX (private branch exchange) – Home or business-use telephone lines – Lines other than those mentioned above. • Do not connect the Wireless LAN Converter to a hub as this affects the correct operation of the Converter. 5GHz Wireless LAN Converter on, you are encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. If you have questions about this product, call the Sony Customer Information Center at 1-877-760-7669; or write to the Sony Customer Information Center at 12451 Gateway Boulevard, Fort Myers, FL 3…

Text truncated - open the document above for the full version.

4-669-391-11(1) Continued on next page 5GHz Wireless LAN Converter Quick Start Guide Before reading this guide, be sure to read the supplement entitled “Read This First”. This guide provides an overview of the 5GHz Wireless LAN Converter PCWA-DE50 features and the necessary configuration steps. Unpacking Once you have unpacked the unit, make sure that all of the following items are present: •Wireless Unit•Power Unit •Power cord •CD-ROM (Setup disc) •Read This First •Quick Start Guide (this manual) •Troubleshooting Guide •Limited Warranty Capabilities Wireless access to the Internet for any device with an Ethernet connector The 5GHz Wireless LAN Converter PCWA-DE50 (hereafter referred to as the Wireless LAN Converter) is designed to enable a device such as a desktop computer or printer equipped with an Ethernet connector to become part of a wireless network. Notes • Only use an Ethernet cable to connect the Wireless LAN Converter to the Ethernet connector of the device. • The Wireless LAN Converter does not function as an Access Point. • For setup of the Wireless LAN Converter, a computer running Windows 98 SE, Windows Me, Windows 2000, or Windows XP is required. • Only one device can be connected to the Wireless LAN Converter. It cannot be connected to a hub. Connection sample: z Hint The Wireless LAN Converter allows also computers equipped with the Wireless LAN Converter to communicate directly when using the Peer to Peer Network connection mode, without using a Wireless LAN Access Point. Access Point Network connection mode settings are described in this manual. Refer to the Online Help for information about Peer to Peer Network connection mode settings. Setup Procedures After setting up the Wireless LAN Converter, connect the Converter to the wireless communication device. Preparation Confirm the computer used for setup and the Access Point Procedure 1 Procedure 2 Procedure 3 Procedure 4 Procedure 7 Procedure 8 Connect the Wireless LAN Converter to the computer used for setup Wireless LAN Converter Setup Install the utility software Configure the Wireless LAN Converter Configuring the Access Point Configure settings for Access Point Reconfigure the Wireless LAN Converter If wireless communication is to be enabled for another device Access Point already set up Installing the Wireless LAN Converter If the computer used for setup is the same as the computer for which wireless communication is to be enabled, the procedure is completed. Wireless LAN Converter installation Connect to a device equipped with an Ethernet connector Device Connection Enabling Wireless Communication Access Point not set up Procedure 5 Procedure 6 z Hint In this guide, each procedure is preceded by a box. Before proceeding to the next procedure, confirm that you have performed all the necessary tasks by ticking the box. Example: Procedure 1 Procedure 2 Connect the Wireless LAN Converter to the computer used for setup Connect the Wireless LAN Converter and the computer. 1Connect the Wireless Unit and Power Unit. 2Connect the Power Unit to the computer using an Ethernet cable. 3Connect the Power Unit to an AC outlet using the power cord. 1 2 3 2 3 z Hints • The Wireless LAN Converter does not have a power switch. • You can use an Ethernet cable with straight-through or crossover wiring. Wireless LAN Converter Setup Procedure 3 Install the utility software Install the utility software for configuring the Wireless LAN Converter (PCWA-DE50 Setup Utility) on the computer to be used for setup. 1Insert the supplied CD-ROM into the computer to which the Wireless LAN Converter is connected. 2For computers running Windows 98 SE, Windows Me, or Windows 2000, double-click the “My Computer” icon on the Desktop. For computers running Windows XP, click “Start” and select “My Computer”. 3In “My Computer”, click the CD-ROM drive icon and then double-click the “PCWA-DE50” folder. 4Double-click “Setup.exe”. The installation program starts. Follow the on-screen instructions and install the utility software. z Hints • Depending on your computer’s settings, the file name “Setup.exe” may be displayed as “Setup”. If there are multiple files named “Setup” in the same folder, double-click the one with the following icon: • To exit the installation program, click “Cancel”. PCWA-DE50 Sony Corporation ©2003 Printed in Japan • Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. • In this manual, Microsoft ® Windows ® 98 Second Edition is referred to as Windows 98 SE, Microsoft ® Windows ® Millennium Edition is referred to as Windows Me, Microsoft ® Windows ® 2000 Professional is referred to as Windows 2000, Microsoft ® Windows ® XP Home Edition and Microsoft ® Windows ® XP Professional are referred to as Windows XP. • Ethernet is a registered trademark of Xerox Corporation. • Netscape and Netscape Communicator are trademarks or registered trademarks of Netscape Communications Corporation. • All other names of systems, products and services are trademarks of their respective owners. In the manual, the ™ or ® marks are not specified. Preparation Procedure 1 Confirm the computer used for setup and the Access Point Before starting setup of the Wireless LAN Converter, verify the following points. Confirm Ethernet connector of computer used for setup Confirm the Ethernet connector of the computer to be used for setup, and provide the required Ethernet cable. z Hint You can use an Ethernet cable with straight-through or crossover wiring. Confirm Access Point Make sure that power to the 5GHz Wireless LAN Access Point to be used is turned on. Also check the Network Name (SSID) and Encryption (WEP) key settings of the Access Point. Network Name (SSID) : ___________________ Encryption (WEP) key : ___________________ Adjust firewall settings of the computer If you are using the Windows XP Internet Connection Firewall or a personal firewall function provided by virus scanning software, it ma…

Text truncated - open the document above for the full version.

PCWA-DE50 Sony Corporation ©2003 Printed in Japan 4-669-392-11(1) 5GHz Wireless LAN Converter Troubleshooting Guide This document provides solutions to most common problems and users have with their Wireless LAN Converter. Please refer to this guide before contacting Sony Customer Information Services. Case 1Starting the PCWA-DE50 Setup Utility results only in the message “Converter not detected. Do you want to see Online Help?”. 1Is the Wireless LAN Converter connected correctly to the computer? Check the connections between the Wireless LAN Converter and computer, the Wireless Unit and Power Unit, and the Power Unit and power outlet. z Hints • When power is supplied to the Wireless LAN Converter, the STATUS indicator will be lit or flashing. However, if the indicator has been set to OFF in the Wireless LAN Converter Setup Page (Advanced Setup), the indicator will only operate in special cases. • When the Wireless LAN Converter is connected to a computer or other device, the LINK/ACT indicator will flash. • You may need to wait for a few seconds to see the Converter in the PCWA-DE50 Setup Utility. 2Is the Ethernet device inside the computer enabled? Check whether the Ethernet device inside the computer is enabled. Windows 98, Windows Me models 1 Right-click “My Computer” on the Desktop, and select “Properties” from the menu that appears. 2 In the “System Properties” dialog box, click the “Device Manager” tab. 3 Click “Network Adapters” to bring up a list of adapters, and verify that the Ethernet adapter that you are using is enabled. z Hint You can also call up detailed information by right-clicking the adapter name and selecting “Properties” from the menu that appears. Windows 2000, Windows XP models 1 With Windows 2000, click “Start”, point to “Settings”, and click “Network and Dial-up Connections” to bring up the “Network and Dial-up Connections” screen. With Windows XP, click “Start”, point to “Connect To” and click “Show all connections” to bring up the “Network Connections” screen. 2 Right-click the Wireless Network Connection icon to be connected and select “Enable” if this is available from the menu. (The illustration shows the Windows XP screen.) Continued on next page 3If the computer connected to the Wireless LAN Converter is running Windows XP, has the Internet Connection Firewall function been enabled? If the Internet Connection Firewall function is enabled, communication may not be possible. Follow the procedure below to check or change the settings. 1 Click “Start”, point to “Connect To”, and click “Show all connections”. 2 Right-click the Wireless Network Connection icon to be connected, and click “Properties”. 3 Click the “Advanced” tab and (if selected) deselect the “Protect my computer and network by limiting or preventing access to this computer from the Internet” check box. 4 Click “OK”. z Hint Refer to Windows XP Online Help for details about the Internet Connection Firewall. Note Take appropriate precautions to ensure security when the Internet Connection Firewall function is disabled. Except when configuring the Wireless LAN Converter or Access Point, it is strongly recommended that you enable the Internet Connection Firewall function at all times. 4When using virus scanning or network security software, has a personal firewall function been enabled? Virus scanning and network security software sometimes includes a function called a “personal firewall” that is designed to prevent illegal access by outside entities. Depending on the software, the security level of this function may be initially set to a high level. If this high security level setting is in effect, it may be impossible to connect to a network. In this case, lower the security level in order to permit the network connection. For details, refer to the instruction manual and online help for your software. 5If the computer connected to the Wireless LAN Converter is running Windows XP, is the Ethernet interface set up to act as a network bridge? Confirm that the Ethernet network connection is not acting as a network bridge. 1 Click “Start”, point to “Connect To”, and click “Show all connections”. 2 Confirm that the Ethernet network connection is not acting as a network bridge. 3 If the Ethernet network connection is configured as a network bridge, right-click the local area connection icon, and click “Remove from Bridge”. z Hint If “Remove from Bridge” is not shown on the shortcut menu, the Ethernet connection is not acting as a network bridge. • Starting the PCWA-DE50 Setup Utility results only in the message “Converter not detected. Do you want to see Online Help?”. ........ Case 1 • When starting the PCWA-DE50 Setup Utility, the message “Failed to open Converter Setup Page. Do you want to see Online Help?” appears. ................................................................. Case 2 • When starting the PCWA-DE50 Setup Utility, the “IP Address Setup” screen appears. ....................................... Case 3 • Cannot display Wireless LAN Converter Setup Page. .................. Case 4 • On the Wireless LAN Converter Setup Page, the Encryption (WEP) key input field cannot be used. .......................................... Case 5 • STATUS indicator is slowly flashing white, but communication with Access Point is not possible. ......................................................... Case 6 • Can no longer connect after Access Point settings were changed. ............................................................................... Case 7 • Can no longer connect after access control (MAC address filtering) of Access Point was enabled. .................. Case 8 • Cannot communicate with device other than the computer used for setup. ............................................................................... Case 9 • Forgot settings/Want to reset. ....................................................... Case 10 • What are the factory default settings? .........................................…

Text truncated - open the document above for the full version.

4-669-393-11(1) Sony Corporation  2003 Printed in Japan PCWA-DE50 Read This First WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Owner’s Record The model and serial numbers are located on the back of the product. Record the serial number in the space provided below. Refer to them whenever you call your Sony dealer regarding this product. Model No. PCWA-DE50 Serial No.______________ CAUTION You are cautioned that any changes or modifications not expressly approved in this manual could void your warranty. Exposure to Radio Frequency Radiation. The radiated output power of the Wireless LAN Converter is far below the FCC radio frequency exposure limits. Nevertheless, the Wireless LAN Converter shall be used in such a manner that the potential for human contact during normal operation is minimized. FCC Radio-Frequency Exposure Statement This equipment generates and radiates radio- frequency energy. In order to comply with FCC radio-frequency radiation exposure guidelines for an uncontrolled environment, this equipment has to be installed and operated while maintaining a minimum body to antenna distance of 20 cm. Based on continuous exposure of 30 minutes. Users are not permitted to make changes or modify the system in any way. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to television reception, which can be determined by turning the equipment off and Safety Information WARNING • Opening the unit, for whatever reason, could lead to damage that is not covered by the warranty. • Do not touch the device or accessories during thunderstorms. Electrical shock could result. • This device is made for use in the USA only. • For indoor use only. • Do not use this equipment on hospital premises. Doing so may cause medical devices to malfunction. • Do not use this equipment in an aircraft, as doing so could cause the aircraft's equipment to malfunction. • While using the Wireless LAN Converter, do not cover it or turn it on its side. Do not cover the Wireless LAN Converter with objects such as magazines or newspapers or use it in confined, enclosed places, such as the spaces between walls and furniture. Furthermore, do not turn the Wireless LAN Converter on its side while using it. Either situation could cause heat to build up inside the Wireless LAN Converter, leading to overheating and possible fire. • Carefully place the Ethernet cable. Personal injury or damage to the Wireless LAN Converter could result from people tripping over the Ethernet cable, Wireless Unit cable, Power Unit, or power cord. Protect wiring by locating it in places where people do not walk. • Do not swing the Wireless LAN Converter. Injury could result if the adapter strikes a person or fragile material, such as glass. • Keep the Wireless LAN Converter out of the reach of children. Unforeseeable injury could result from swallowing loose parts, etc. • Place the Wireless LAN Converter on a stable surface. Do not place the Wireless LAN Converter on wobbly or tilted surfaces. Tipping or falling could result in injury. • When using wall mounting, make sure that the wall is strong enough to support the Wireless Unit. The Wireless Unit could fall if the wall is not strong enough, leading to unforeseeable accidents. Further, be careful not to drop the unit or the tools used for mounting it. Doing so could result in unforeseeable accidents. • Avoid locations that are directly exposed to sunlight or heaters. Internal overheating could result in fire or damage to the unit. • Make sure connectors are properly connected. – Do not insert any metallic objects inside the connectors. Short-circuiting the pins could cause fire or damage to the unit. – Be careful to insert connectors squarely. Crooked insertion could cause pins to short- circuit, possibly causing fire or damage to the unit. • Use only the supplied Power Unit with your Sony Wireless LAN Converter. To disconnect your Wireless LAN Converter from the power supply, unplug the Power Unit. • ISDN and telephone lines cannot be connected to the Wireless Unit connector and/or NETWORK connector of the Power Unit. If the Power Unit is connected to the network or telephone lines mentioned below, high electric current to the connectors may cause damage, overheating or fire. Connecting to home or business-use telephone lines is strictly prohibited. – Telephone lines – PBX (private branch exchange) – Home or business-use telephone lines – Lines other than those mentioned above. • Do not connect the Wireless LAN Converter to a hub as this affects the correct operation of the Converter. 5GHz Wireless LAN Converter on, you are encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. If you have questions about this product, call the Sony Customer Information Center at 1-877-760-7669; or write to the Sony Customer Information Center at 12451 Gateway Boulevard, Fort Myers, FL 3…

Text truncated - open the document above for the full version.

Akzo Nobel K. K. EMC Division Bancho Kaikan 12-1, Gobancho, Chiyoda-ku Tokyo 102-0076 Japan Tel.+81 3 5210 5411 Fax.+81 3 5216 2860 February 13, 2003 Federal Communications Commission Office of Engineering and Technology 7435 Oakland Mills Road Columbia, MD 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize PCTEST Engineering Laboratory, Inc. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988,21 U.S.C.862. This authorization expires one year from the current date. Sincerely, Akzo Nobel K. K. Junichi Okada Group Leader Technology Management Group EMC Division

ID label

Antenna description ·Manufacturer’s name : TOKO ·Type : ASW52AU ·Usage : 5GHz Wireless LAN ·Structure : Circular polarization antenna with 90 degree hybrid feed circuit and 2 point feeding dielectric patch. ·Specification –Center frequency5.2GHz –Impedance50 ohm –Temperature range-20 to +85 deg Celsius –Storage temperature-40 to +90 deg Celsius –Weight2.5 gram –Band width> 0.05 GHz –PolarizationCircular polarization (right rotation) –Gain4.0 dBi (5.2GHz) –FB ratio> 6 dB -90 -85 -80 -75 -70 -65 -60 -55 -50 -45 -40 -35 -30 -25 -20 -15 -10 -5 0 5 2 3 4 5 6 7 8 9 10 11 1 2 1 1 15 16 17 18 19 20 21 22 23 24 25 2627 28 29 30 31 32 33 34 35 36 37 8 9 0 41 42 43 44 45 46 47 48 49 50 51 -90 -85 -80 -75 -70 -65 -60 -55 -50 -45 -40 -35 -30 -25 -20 -15 -10 -5 0 5 2 3 4 5 6 7 8 9 10 11 1 2 1 1 15 16 17 18 19 20 21 22 23 24 25 2627 28 29 30 31 32 33 34 35 36 37 8 9 0 41 42 43 44 45 46 47 48 49 50 51 Radiation pattern Left H-pol. Right V-pol. Antenna 1 A ntenna 2 Transmitter circuit

Maximum Permissible Exposure (MPE) Evaluation Applicant: Sony Corporation Equipment: Wireless LAN Converter Model No.: PCWA-DE50 FCC ID: AK8PCWADE50 MPE Calculations According to the OET Bulletin 65 (Edition 97-01) Where: S=power density (in appropriate units, e.g. mW/cm 2 ) P=power input to antenna (in appropriate units, e.g., mW) G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna (appropriate units, e.g., cm) Tx Frequency= 5260(MHz) Maximum peak power=16.4(dBm) Antenna gain=4.0(dBi) S=1 (mW/cm 2 ) P= 43.65 (mW) G= 2.51(numeric) R= 2.95(cm) The calculated minimum separation distance from antenna :2.95(cm) Notice in the User manual FCC Radio-Frequency Exposure Statement This equipment generates and radiates radio-frequency energy. In order to comply with FCC radio-frequency radiation exposure guidelines for an uncontrolled environment, this equipment has to be installed and operated while maintaining a minimum body to antenna distance of 20 cm. Based on continuous exposure of 30 minutes. S PG R π4 = 2 4R PG S π =

Maximum Permissible Exposure (MPE) Evaluation Applicant: Sony Corporation Equipment: Wireless LAN Converter Model No.: PCWA-DE50 FCC ID: AK8PCWADE50 MPE Calculations According to the OET Bulletin 65 (Edition 97-01) Where: S=power density (in appropriate units, e.g. mW/cm 2 ) P=power input to antenna (in appropriate units, e.g., mW) G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna (appropriate units, e.g., cm) Tx Frequency=5260(MHz) Maximum peak power=16.4(dBm) Antenna gain=4.0(dBi) P= 43.65(mW) G=2.51(numeric) R=20.0(cm) S= 0.0218 (mW/cm 2 )(MPE limit = 1.0 mW/cm 2 ) The Maximum power density at 20cm distance is calculated as : 0.0218 (mW/cm 2 ) Notice in the User manual FCC Radio-Frequency Exposure Statement This equipment generates and radiates radio-frequency energy. In order to comply with FCC radio-frequency radiation exposure guidelines for an uncontrolled environment, this equipment has to be installed and operated while maintaining a minimum body to antenna distance of 20 cm. Based on continuous exposure of 30 minutes. 2 4R PG S π =

T E S T R E P O R T REPORT NUMBER:ANKK−103028 APPLICANT:Sony Corporation MODEL NUMBER:PCWA-DE50 FCC ID:AK8PCWADE50 REGULATION:FCC Part15 Subpart E 1, Oaza Sunayama, Hasaki-machi, Kashima-gun Ibaraki-ken, 314-0255 Japan Tel.: +81 479 40 1097 Fax.: +81 479 46 1788 Akzo Nobel K. K. EMC Division Kashima Site NVLAP accreditation is valid for FCC Part15 (Digital Devices), CISPR22 and AS/NZS 3548. NVLAP accreditation does not cover ICES−003. Akzo Nobel Report No. ANKK−103028 FCC ID : AK8PCWADE50 Page 2 of 75 TABLE OF CONTENTS Page ABBREVIATIONS .......................................................................................................................... 3 SECTION 1.TEST CERTIFICATION ...................................................................................... 4 SECTION 2.SUMMARY OF RESULTS ................................................................................... 5 SECTION 3.EQUIPMENT UNDER TEST............................................................................... 6 SECTION 4.SUPPORT EQUIPMENT USED .......................................................................... 8 SECTION 5.CABLE (S) USED................................................................................................. 9 SECTION 6.CONSTRUCTION OF EQUIPMENT ................................................................. 10 SECTION 7.GENERAL TEST CONDITIONS ....................................................................... 11 SECTION 8.TEST PROCEDURE(S) ...................................................................................... 12 SECTION 9.TEST DATA ....................................................................................................... 16 9.1 26dB Emission Bandwidth [15.407(a)(1), 15.407(a)(2)] .....................................................16 …

Text truncated - open the document above for the full version.