AK8VGPWRC92.4G RF Receiver

1 Sony 2.4G RF Receiver VGP‐WRC9 2 Sony 2.4G RF Receiver VGP‐WRC9 3 Sony 2.4G RF Receiver VGP‐WRC9 4 Sony 2.4G RF Receiver VGP‐WRC9 Note: For Model VGP‐WKB16, will use Firmware to lock some frequency. So its frequency range is from 2402MHz to 2478MHz only. Total channel number is 77. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: AK8VGPWRC9". This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. End Product Labeling The final end product must be labeled in a visible area with the following: “Contains transmitter module IC: 409B-VGPWRC9”. CAN ICES-3 (B)/NMB-3(B)

Sony Corporation 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Limited Module Approval Request Letter Subject: Limited Module Approval Date: August 16, 2013 FCC ID: AK8VGPWRC9 Dear Reviewer, We, Sony Corporation would request 2.4G RF Receiver approved under limited module approval authorization. The application of this module is specified to both portable and mobile host equipment. The requirements regulated in 15.212 have been fulfilled and clearly explained below. 1. The requirement of RF shielding: The module does not contain a separate shield. However, this module will not be offered for sale to, or use by other company or OEM. As the manufacturer of the module and any host products into which this module will be installed, power Monitors retains full control over the final installation of the device into its products, and therefore can assure the compliance of the end product to the tested results. 2. The requirement of buffered inputs: Buffered data inputs stage has been integrated in chip (CYRF8935). 3. The requirement of power supply regulation: The part number of the power regulator is (CYRF8935). 4. The requirements of section 15.203 and 15.204(C): The requirements of antenna connector and spurious emission have been fulfilled. Please reference the exhibition Test Report. 5. The requirement of stand-alone test configuration: Please reference exhibition Test Configuration Photo for the stand-alone test configuration. 6. The requirement of labeling: The instruction on the labeling rule of the end product has been stated in the user’s manual of this module. Please also see the exhibition Label Sample. 7. The requirement of compliance on specific rule or operating requirements: The required FCC rule has been fulfilled and all the instructions for maintaining compliance have been clearly stated in the Users Manual. 8. The requirement of RF exposure: The module only radiates very low power levels; it complies with RF exposure requirement. Please do not hesitate to contact me for any questions of this request letter. Thank you. Applicant’s company name : Sony Corporation Applicant’s company address : 1-7-1 Konan, Minato-ku, Tokyo 108-0075, Japan Signature : _________________________________ Job Title and Dept. : Ryui Tatsumi / Senior Manager E-mail : [email protected] Tel. : (81)263-71-8924

Sony Corporation 1-7-1 Konan Minato-ku, Tokyo, 108-0075 , Japan Date: 2013/8/5 Federal Communications Commission 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Product Certification Representative Authorization Letter FCC ID: AK8VGPWRC9 Product name: 2.4G RF Receiver To whom it may concern: We the undersigned, hereby authorize following person to act as our agent in the preparation of an application for equipment authorization of model VGP-WRC9 to the FCC Rules and Regulations. Sporton International Inc. Address : No. 52, Hwa Ya 1st Road., Kwei-Shan Hsiang, TaoYuan Hsien Taiwan R.O.C. Name : Wayne Hsu Job Title : Vice Manager e-mail : [email protected] We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002(b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 835(a). This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Applicant : Sony Corporation Address : 1-7-1 Konan, Minato-ku, Tokyo 108-0075, Japan Signature : _________________________________ Name and Job Title. : Ryui Tatsumi / Section Manager E-mail : [email protected] Tel. : (81)263-71-8924

Sony Corporation 1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Tel +81-3-6748-2111 Date: August 20, 2013 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Request for confidentiality FCC ID: AK8VGP-WRC9 To whom it may concern: Short-term confidentiality Pursuant to DA 04-1705 of the Commission’s pubic notice, in order to comply with the marketing regulations in 47CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until February 1, 2014. 1. Internal Photographs 2. External Photographs 3. User’s manual 4. Test Set up photos Permanent confidentiality Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant Hereby requests confidential treatment of information accompanying this Application As outlined below: 1. Block Diagram 2. Schematics 3. Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Applicant : Sony Corporation Address : 1-7-1 Konan, Minato-ku, Tokyo 108-0075, Japan Signature : _________________________________ Name and Job Title. : Ryui Tatsumi / Section Manager E-mail : [email protected]

FCC Test Report Report No. : EP37 0612 SPORTON International Inc. PAGE NUMBER : B1 OF B2 TEL : 886-3-327-3456 ISSUED DATE : Aug. 14, 2013 FAX : 886-3-327-0973 APPENDIX B. Photographs of EUT

RF label

FCC Test Report Report No. : EP37 0612 SPORTON International Inc. PAGE NUMBER : B1 OF B2 TEL : 886-3-327-3456 ISSUED DATE : Aug. 14, 2013 FAX : 886-3-327-0973 APPENDIX B. Photographs of EUT FCC Test Report Report No. : EP37 0612 SPORTON International Inc. PAGE NUMBER : B2 OF B2 TEL : 886-3-327-3456 ISSUED DATE : Aug. 14, 2013 FAX : 886-3-327-0973

FCC Test Report Report No. : FR370612 SPORTON INTERNATIONAL INC. Page No. : 1 of 30 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 FCC Test Report Equipment : 2.4G RF Receiver Brand Name : SONY Model No. : VGP-WRC9 FCC ID : AK8VGPWRC9 Standard : 47 CFR FCC Part 15.249 Operating Band : 2400 MHz – 2483.5 MHz FCC Classification : DXX Applicant Manufacturer : Sony Corporation 1-7-1 Konan, Minato-ku, Tokyo 108-0075, Japan The product sample received on Jul. 18, 2013 and completely tested on Aug. 05, 2013. We, SPORTON, would like to declare that the tested sample has been evaluated in accordance with the procedures given in ANSI C63.10-2009 and shown compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC., the test report shall not be reproduced except in full. Reviewed by: Wayne Hsu / Assistant Manager FCC Test Report Report No. : FR370612 SPORTON INTERNATIONAL INC. Page No. : 2 of 30 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Table of Contents 1 GENERAL DESCRIPTION ............................................................................................................... 5 1.1 Information ........................................................................................................................................ 5 1.2 Support Equipment ........................................................................................................................... 7 1.3 Testing Applied Standards ................................................................................................................ 7 1.4 Testing Location Information ............................................................................................................. 7 1.5 Measurement Uncertainty ................................................................................................................. 8 2 TEST CONFIGURATION OF EUT .................................................................................................... 9 2.1 The Worst Case Modulation Configuration ........................................................................................ 9 2.2 Test Channel Frequencies Configuration ........................................................................................... 9 2.3 The Worst Case Measurement Configuration .................................................................................... 9 2.4 Test Setup Diagram ........................................................................................................................ 10 3 TRANSMITTER TEST RESULT ..................................................................................................... 12 3.1 AC Power-line Conducted Emissions .............................................................................................. 12 3.2 Emission Bandwidth ........................................................................................................................ 15 3.3 Fundamental Emissions .................................................................................................................. 17 3.4 Transmitter Radiated Unwanted Emissions ..................................................................................... 19 4 TEST EQUIPMENT AND CALIBRATION DATA ............................................................................. 29 APPENDIX A. TEST PHOTOS APPENDIX B. PHOTOGRAPHS OF EUT FCC Test Report Report No. : FR370612 SPORTON INTERNATIONAL INC. Page No. : 3 of 30 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Summary of Test Result Conformance Test Specifications Report Clause Ref. Std. Clause Description Measured Limit Result 1.1.2 15.203 Antenna Requirement Antenna connector mechanism complied FCC 15.203 Complied 3.1 15.207 AC Power-line Conducted Emissions [dBuV]: 0.2050460MHz 42.80 (Margin 10.60dB) - AV 51.96 (Margin 11.44dB) - QP FCC 15.207 Complied 3.2 15.215(c) Emission Bandwidth 2.50 MHz; fall in band Information only Complied 3.3 15.249(a) Fundamental Emissions [dBuV/m at 3m]: 72.92 (Margin 21.08dB) average [dBuV/m at 3m]: average: 94 Complied 3.4 15.249(a)/(d) Transmitter Radiated Unwanted Emissions [dBuV/m at 3m]:164.83MHz 39.11 (Margin 4.39dB) - PK Harmonics: 54 dBuV/m@3m Other band: 50 dB or FCC 15.209, whichever is the lesser attenuation. Complied FCC Test Report Report No. : FR370612 SPORTON INTERNATIONAL INC. Page No. : 4 of 30 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Revision History Report No. Version Description Issued Date FR370612 Rev. 01 Initial issue of report Aug. 14, 2013 902 MHz – 928 MHz FCC Test Report Report No. : FR370612 SPORTON INTERNATIONAL INC. Page No. : 5 of 30 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 1 General Description 1.1 Information 1.1.1 RF General Information RF General Information Frequency Range (MHz) Modulation Ch. Frequency (MHz) Channel Number Fundamental Field Strength (dBuV/m) Co-location 2400-2483.5 GFSK 2402~2478 77 72.92 N/A Note 1: Field strength performed average level at 3m. Note 2: Co-location, Co-location is generally defined as simultaneously transmitting (co-transmitting) antennas within 20 cm of each other. (i.e., EUT has simultaneously co-transmitting that operating 2.4GHz and 5GHz.) 1.1.2 Antenna Information Antenna Category Integral antenna (antenna permanently attached) External antenna (dedicated antennas) ; Unique antenna connector 1.1.3 Type of EUT Identify EUT EUT Serial Number N/A Presentation of Equipment Production ; Pre-Production ; Prototype Type of EUT Stand-alone Combined (EUT where the radio part is fully integrated within another device) Combined Equipment - Brand Name / Model No.: Plug-in radio (EUT intended for a variety of host systems) Host System - Brand Name / Model No.: Other: FCC Test Report Report No. : FR370612 SPORTON INTERNA…

Text truncated - open the document above for the full version.

FCC Test Report Report No. : FR370612 SPORTON INTERNATIONAL INC. Page No. : A1 of A7 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 Appendix A. Test Photos FCC Test Report Report No. : FR370612 SPORTON INTERNATIONAL INC. Page No. : A2 of A7 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 1 Photographs of Conducted Emissions Test Configuration FRONT VIEW REAR VIEW FCC Test Report Report No. : FR370612 SPORTON INTERNATIONAL INC. Page No. : A3 of A7 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 SIDE VIEW FCC Test Report Report No. : FR370612 SPORTON INTERNATIONAL INC. Page No. : A4 of A7 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 2 Photographs of Radiated Emissions Test Configuration For radiated emissions 9kHz~30MHz FRONT VIEW REAR VIEW FCC Test Report Report No. : FR370612 SPORTON INTERNATIONAL INC. Page No. : A5 of A7 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 For radiated emissions 30MHz~1GHz FRONT VIEW REAR VIEW FCC Test Report Report No. : FR370612 SPORTON INTERNATIONAL INC. Page No. : A6 of A7 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 For radiated emissions above 1GHz FRONT VIEW REAR VIEW FCC Test Report Report No. : FR370612 SPORTON INTERNATIONAL INC. Page No. : A7 of A7 TEL : 886-3-327-3456 Report Version : Rev. 01 FAX : 886-3-327-0973 EUT take a close-up. FRONT VIEW