APIJBLV100NXTBluetooth Headset

135-00533-8-5 4F TEL: 0570-550-465 Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. • Reorient or relocate the receiving antenna. • • Connect the equipment into an outlet on a circuit different from that to • Consult the dealer or an experienced radio/TV technician for help. Increase the separation between the equipment and receiver. which the receiver is connected. FCC Caution: An y changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interf erence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interf erence to radio or television reception, which can be deter mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 080-2432_C

Everest Elite100 Quick Start Guide Guide de démarrage rapide Everest Elite100 Overview – Buttons & LEDs 1 M M To pair Bluetooth with device 3 Turn on headphone to pair 2 Quick Start Guide Guide de démarrage rapide Everest Elite100 ON 3.0s OFF 3.0s JBL Everest Elite 100 JBL Everest Elite 100 To download My JBL Headphones App 4 To adjust the Ambient Aware level 5 Quick Start Guide Guide de démarrage rapide Everest Elite100 Download the My JBL Headphones App for the following features: stereo setup, firmware upgrade, and device renaming. /Téléchargez l'application My JBL Headphones App pour les fonctions suivantes : configuration stéréo, mise à jour de micrologiciel et changement de nom d'appareil. / Descargue la aplicación My JBL Headphones App para disfrutar de las funciones siguientes: configuración estéreo, actualización del firmware y renombrado de dispositivos. / Baixe o aplicativo My JBL Headphones App para usar os seguintes recursos: configuração estéreo, atualização de firmware e mudança dos nomes dos dispositivos. / Lade die My JBL Headphones App herunter, um über folgende Funktionen zu verfügen: Stereo-Einstellung, Firmware-Aufrüstung und Geräteumbenennung. / Scarica l'applicazione My JBL Headphones App per le seguenti funzionalità: configurazione stereo, aggiornamento del firmware, e ridenominazione del dispositivo. / Download de My JBL Headphones App voor de onderstaande functies: stereo setup, firmware upgrade, en appraten hernoemen. / Last ned My JBL Headphones App for følgende funksjoner: stereooppsett, oppgradering av fastvare og omdøping av enhet. / Lataa My JBL Headphones App -sovellus saadaksesi käyttöön seuraavat ominaisuudet: stereoasetukset, laiteohjelmistopäivitykset ja laitteiden uudelleen nimeäminen. / Загрузите приложение My JBL Headphones App для доступ а к следующим функциям: настройка стереозвучания, обновление микропрограммы и переи менование устройства. / Ladda ner appen My JBL Headphones App som har följande funktioner: stereoinställning, uppgradering av fast programvara och nya namn på enheter. / Download appen My JBL Headphones App for at få adgang til følgende funktioner: stereokonfiguration, firmwareopgradering og omdøbning af enheder. / 以下の機能を使用するために、My JBL Headphones App ･アプリをダウンロードしてください:ステレオ･セットアップ、ファームウェアのアッ プグレード、機器の名称変更. / Pobierz aplikację My JBL Headphones App, aby korzystać z następujących funkcji: konfiguracja stereo, aktualizacja oprogramowania układowego oraz zmiana nazwy urządzenia. /My JBL Headphones App 음악 앱을 다운로드하여 다음을 따릅니다. 스테레오 설정, 펌웨어 업그레이드 및 장치 이름 바꾸기. /下载 My JBL Headphones App应用，即可使用以下功能： 立体声 设置、固件升级和设备重命名。 /下載 My JBL Headphones App應用程式以使用下列功能： 立體聲設定 、韌體升級以及裝置重新命名。 / Unduh aplikasi My JBL Headphones App untuk fitur-fitur berikut ini: pengaturan stereo, memperbarui firmware, dan penamaan ulang perangkat. FPOFPO FPO FPOFPO FPO FPOFPO FPO FPOFPO FPO FPOFPO FPO FPOFPO FPO FPOFPO FPO FPOFPO FPO FPOFPO FPO FPOFPO FPO FPOFPO FPO FPOFPO FPO FPOFPO FPO FPOFPO FPO FPOFPO FPO FPO FPO FPO High Level Low Level Turn off Ambient Aware M Multi-function Button (MFB) to control music 6 Multi-function Button (MFB) to control calls 7 Quick Start Guide Guide de démarrage rapide Everest Elite100 Play or Pause Next track Previous track Press Press x2 Press x3 Answer / hang up Reject call Press Long Press Multi-function Button (MFB) to manage second incoming call 8 Answer 2nd incoming call and put current call on hold Hang up current call and switch to second call 12 Press Long Press M M M Quick Start Guide Guide de démarrage rapide Everest Elite100 Multi-function Button (MFB) to manage 2 calls at the same time 9 To adjust volume 10 To charge battery 11 Switch calls Hang up current call and switch to second call LED Status LED behaviors Charging battery Battery is charged full 12 Press Long Press M • Model: V100NXT • Tamaño de la unidad: 13,5mm • Alcance de respuesta dinámica en frecuencias: 10-22k Hz • Sensibilidad de la unidad: 99dB / 1kHz, 1mW • SPL máximo: 109 dB • Sensibilidad del micrófono: -42dBV/Pa • Potencia transmitida del Bluetooth ® : < 4 dBm • Modulación transmitida del Bluetooth ® : GFSK/π/4-DQPSK/8-DPSK • Especificaciones del Bluetooth ® 4.0 • Perfiles del Bluetooth ® A2DP V1.2, AVRCP V1.4, HFP V1.6 • Tipo de batería: Batería de iones de polímero de litio (3.7V, 60mAh) • Tiempo de carga: 2,5 horas • Tiempo de reproducción de música con ANC conectado y Bluetooth conectado: up to 6 hours • Talk time with ANC and BT on: up to 6 hours • DimensionesdelauricularAxAxL(mm): 15.5 x 13.7 x 29.3 • Dimensiones de la carcasa del neck AxAxL(mm):146x21.2x169 • Peso (kg): 0.04 ES • Model: V100NXT • Driver size: 13.5mm • Dynamic frequency response range: 10-22k Hz • Driver sensitivity: 99dB / 1kHz, 1mW • Maximum SPL: 109dB • Microphone sensitivity: -42dBV/Pa • Bluetooth ® transmitted power: <4dBm • Bluetooth ® transmitted modulation: GFSK π/4, DQPSK, 8-DPSK • Bluetooth ® spec: 4.0 • Bluetooth ® profiles: A2DP V1.2, AVRCP V1.4, HFP V1.6 • Battery type: Polymer Li-ion Battery (3.7V, 60mAh) • Charging time: 2.5 hours • Music play time with ANC on and Bluetooth on: up to 6 hours • Talk time with ANC and BT on: up to 6 hours • Earbud dimension W x H x L (mm): 15.5 x 13.7 x 29.3 • Neck housing diemnsion W x H x L (mm): 146 x 21.2 x 169 • Weight (kg): 0.04 EN • Model: V100NXT • Tamanho do driver: 13,5 mm • Intervalo de resposta dinâmica de frequência: 10 Hz a 22 kHz • Sensibilidade do driver: 99 dB / 1 kHz, 1 mW • Potência SPL máxima: 109 dB • Sensibilidade do microfone: -42 dBV/Pa • Potência do transmissor Bluetooth ® : < 4 dBm • Modulação do transmissor Bluetooth ® :GFSK, π/4, DQPSK e 8-DPSK • Especificação Bluetooth ® :4.0 • Perfis Bluetooth ® : A2DP V1.2, AVRCP V1.4, HFP V1.6 e • Tipo de bateria: Bateria de polímero e íon de lítio (3,7 V, 60 mAh) • Tempo de conversação: 2,5 horas • Tempo de reprodução de música com ANC e Bluetooth ligados: up to 6 hours • Talk time with ANC and BT on: up to 6 hours • Dimensões do earbud L x A x C (mm): 15,5 x 13,7 x 29,3 • Dime…

Text truncated - open the document above for the full version.

Request for Confidentiality Date: 2015/11/5 Subject: Confident iality Request for: FCC ID: APIJBLV100NXT Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Ex h i bi t Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 1 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual Short Term Permanent P ar t Lis t *Note: ______(Insert Explanation as Necessary)______ _Harman International Industries, Incorporated__has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competit ion" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanent ly withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180 ) 2 ___ days from the date of the Grant of Equipment Author izat ion and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aw are that they are responsible to notify TCB in the event information regarding the product or the product is made available to the public. TCB w ill then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 0 4-1705. NO TE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confident iality, either type of marked exhibit above will simply be marked Confident ial when submitted t o I C. S inc er ely, By : __ Tim Song____ (Print name)

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 4 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Photographs - EUT Constructional Details Test model No.: V100NXT SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 4 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 4 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 4 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

10,12,72,8 JBL Phoenix In-Ear BT/ANC Headphones 04. 08. 2015 40 60 JBL Phoenix In-Ear BT/ANC Headphones 04. 08. 2015 Made In China/Сделано в Китае/中国制造 Bluetooth headset/Пользовательские наушники/蓝牙耳机 IC: 6132A-JB LV100NXT CMIIT ID: XXXXXXXXXX MODEL: V 100NXT FCC ID: APIJBLV100NXT XXXXX/SDPPI/2015 4534 XXX-XXX-XXX-XXXXXXX CC AEXXXXXXXX XXX-XXXXXX 0890

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Photographs - EUT Constructional Details Test model No.: V100NXT SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 5 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, …

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM151000662802 Page: 1 of 7 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page SAR Evaluation Report Application No.: SZEM1510006628CR Applicant: Harman International Industries, Incorporated Manufacturer: Harman International Industries, Incorporated Factory: Shenzhen Grandsun Electronic Co., Ltd. Product Name: Bluetooth Headset Model No.(EUT): V100NXT FCC ID: APIJBLV100NXT Standards: 47 CFR Part 1.1307 (2014) 47 CFR Part 2.1093 (2014) KDB447498D01 General RF Exposure Guidance v05r02 Date of Receipt: 2015-11-11 Date of Test: 2015-11-13 to 2015-11-17 Date of Issue: 2015-11-19 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM151000662802 Page: 2 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2015-11-19 Original Authorized for issue by: Tested By 2015-11-17 (Benson Wang) /Project Engineer Date Prepared By 2015-11-19 (Link Liang) /Clerk Date Checked By 2015-11-19 (Eric Fu) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM151000662802 Page: 3 of 7 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Cont…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM151000662801 Page: 1 of 99 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless o…

Text truncated - open the document above for the full version.