APIJBLV300BTBluetooth Headphone

RSS standard(s). This device complies with Industry Canada's licence-exempt RSSs. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. AVERTISSEMENT : Ne pas ingérer BATTERIE, BURN RISQUE CHIMIQUE [La télécommande fournie avec] Ce produit contient une pile pièce / bouton. Si la pile pièce / bouton est avalé, il peut causer des brûlures internes graves en seulement 2 heures et peut conduire à la mort. Gardez piles neuves et usagées de portée des enfants. Si vous pensez que les batteries pourraient avoir été avalé ou placé à l'intérieur d'une partie du corps, consulter immédiatement un médecin.

Everest 300/700 Everest 700 Everest 300 Overview – Buttons & LEDs Quick Start Guide Guide de démarrage rapide Everest 300/700 3 hr / Everest 700 2 hr / Everest 300 Cable connections 1 To turn on Bluetooth to pair 2 ON 2.0s OFF 2.0s Quick Start Guide Guide de démarrage rapide Everest 300/700 To pair Bluetooth with the device 3 JBL Everest 700 JBL Everest 700 JBL Everest 300 JBL Everest 300 Quick Start Guide Guide de démarrage rapide LED Status LED behaviors Power on Bluetooth connected Bluetooth disconnected ON Flashing ON Everest 300/700 4 Connectors in Everest right earcups Quick Start Guide Guide de démarrage rapide To turn off Bluetooth radio when battery is low. Listen to music using audio cable LED Status LED behaviors Battery level is low Charging battery Battery is charged full Everest 300/700 Quick Start Guide Guide de démarrage rapide To use ShareMe ™ 2.0 5 ShareMe ™ 2.0 ShareMe 2.0 enables sharing your audio with another set of Bluetooth wireless headphones of any brand. 1 2 Everest 300/700 Quick Start Guide Guide de démarrage rapide 5a EN Step 1: Pair and connect JBL Everest headphone to a source device Step 2: Pause music or disengage the voice call from the source device Step 3: Press “ShareMe 2.0” button, the white LED starts blinking. JBL Everest headphone is ready to connect to the other headphone. Step 4: Turn on the pairing function in the other headphone. Keep both headphones near each other. The white LED stops flashing and remains lit after two headphones connect. Step 5: Press the play button in the source device to share audio between two headphones. Step 6: Press “ShareMe 2.0” button to turn off this feature. The white LED is off. FR Step 1: Pair and connect JBL Everest headphone to a source device Step 2: Pause music or disengage the voice call from the source device Step 3: Press “ShareMe 2.0” button, the white LED starts blinking. JBL Everest headphone is ready to connect to the other headphone. Step 4: Turn on the pairing function in the other headphone. Keep both headphones near each other. The white LED stops flashing and remains lit after two headphones connect. Step 5: Press the play button in the source device to share audio between two headphones. Step 6: Press “ShareMe 2.0” button to turn off this feature. The white LED is off. ES Step 1: Pair and connect JBL Everest headphone to a source device Step 2: Pause music or disengage the voice call from the source device Step 3: Press “ShareMe 2.0” button, the white LED starts blinking. JBL Everest headphone is ready to connect to the other headphone. Step 4: Turn on the pairing function in the other headphone. Keep both headphones near each other. The white LED stops flashing and remains lit after two headphones connect. Step 5: Press the play button in the source device to share audio between two headphones. Step 6: Press “ShareMe 2.0” button to turn off this feature. The white LED is off. PT Step 1: Pair and connect JBL Everest headphone to a source device Step 2: Pause music or disengage the voice call from the source device Step 3: Press “ShareMe 2.0” button, the white LED starts blinking. JBL Everest headphone is ready to connect to the other headphone. Step 4: Turn on the pairing function in the other headphone. Keep both headphones near each other. The white LED stops flashing and remains lit after two headphones connect. Step 5: Press the play button in the source device to share audio between two headphones. Step 6: Press “ShareMe 2.0” button to turn off this feature. The white LED is off. DE Step 1: Pair and connect JBL Everest headphone to a source device Step 2: Pause music or disengage the voice call from the source device Step 3: Press “ShareMe 2.0” button, the white LED starts blinking. JBL Everest headphone is ready to connect to the other headphone. Step 4: Turn on the pairing function in the other headphone. Keep both headphones near each other. The white LED stops flashing and remains lit after two headphones connect. Step 5: Press the play button in the source device to share audio between two headphones. Step 6: Press “ShareMe 2.0” button to turn off this feature. The white LED is off. IT Step 1: Pair and connect JBL Everest headphone to a source device Step 2: Pause music or disengage the voice call from the source device Step 3: Press “ShareMe 2.0” button, the white LED starts blinking. JBL Everest headphone is ready to connect to the other headphone. Step 4: Turn on the pairing function in the other headphone. Keep both headphones near each other. The white LED stops flashing and remains lit after two headphones connect. Step 5: Press the play button in the source device to share audio between two headphones. Step 6: Press “ShareMe 2.0” button to turn off this feature. The white LED is off. NL Step 1: Pair and connect JBL Everest headphone to a source device Step 2: Pause music or disengage the voice call from the source device Step 3: Press “ShareMe 2.0” button, the white LED starts blinking. JBL Everest headphone is ready to connect to the other headphone. Step 4: Turn on the pairing function in the other headphone. Keep both headphones near each other. The white LED stops flashing and remains lit after two headphones connect. Step 5: Press the play button in the source device to share audio between two headphones. Step 6: Press “ShareMe 2.0” button to turn off this feature. The white LED is off. NO Step 1: Pair and connect JBL Everest headphone to a source device Step 2: Pause music or disengage the voice call from the source device Step 3: Press “ShareMe 2.0” button, the white LED starts blinking. JBL Everest headphone is ready to connect to the other headphone. Step 4: Turn on the pairing function in the other headphone. Keep both headphones near each other. The white LED stops flashing and remains lit after two headphones connect. Step 5: Press the play button in the source device to share audio between two headphones. Step 6: Press “ShareMe 2.0” button to turn off this feature.…

Text truncated - open the document above for the full version.

Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R15Q0731-1E2 Page 55 of 64 14. Photos of the EUT Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R15Q0731-1E2 Page 56 of 64 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R15Q0731-1E2 Page 57 of 64

Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R15Q0731-1E2 Page 58 of 64 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R15Q0731-1E2 Page 59 of 64 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R15Q0731-1E2 Page 60 of 64 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R15Q0731-1E2 Page 61 of 64 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R15Q0731-1E2 Page 62 of 64 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R15Q0731-1E2 Page 63 of 64 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R15Q0731-1E2 Page 64 of 64 END OF REPORT

RF Exposure evaluation       !"#$%&'' () *+ +,"&$!'&*&*!&-./01/0 &&%  & & İ )22 234 562 $7% 8- * !9 !' '+'% ! 92 :;<627 && %   & 9 22;=g5Ĝ-6/0;=İ 7-+," İ 7)-+$24,"98*  -6/0;&*"* ! &2->'4/0 8 &  '* &2: 223- !'!  *&'!&'2 !%! -2% &  :& && &3!85?./0972 261.332:;'%'%8=  67<);g5Ĝ?76/0;=@71A7-+,"  *,"( !' &>'       2440MHz,

Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R15Q0731-1E2 Page 1 of 52 FCC AND IC CERTIFICATION TEST REPORT FOR Issued By: Dongguan Dongdian Testing Service Co., Ltd. Add: No. 17, Zongbu Road 2, Songshan Lake Sci&Tech, Industry Park, Dongguan City, Guangdong Province, China, 523808 Tel: +86-0769-22891499 Http://www.dgddt.com Applicant : Harman International Industries, Incorporated Address : 8500 Balboa Boulevard, Northridge, CA 91329, UNITED STATES Equipment under Test : Bluetooth Headphone Model No : V300BT Trade Mark : JBL FCC ID : APIJBLV300BT IC : 6132A-JBLV300BT Manufacturer : Harman International Industries, Incorporated Address : 8500 Balboa Boulevard, Northridge, CA 91329, UNITED STATES Report No.: DDT-R15Q0731-1E2 Issued Date: Aug. 14, 2015 Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R15Q0731-1E2 Page 2 of 52 TABLE OF CONTENTS Test report declares.....................................................................................................................3 1. Summary of test results ............................................................................................................... 5 2. General test information .............................................................................................................. 6 2.1. Description of EUT ..................................................................................................................... 6 2.2. Accessories of EUT ..................................................................................................................... 6 2.3. Assistant equipment used for test ................................................................................................ 6 2.4. Block diagram of EUT configuration for test ............................................................................. 6 2.5. Test environment conditions ....................................................................................................... 7 2.6. Test laboratory ............................................................................................................................. 7 2.7. Measurement uncertainty ............................................................................................................ 7 3. Maximum Peak Output Power .................................................................................................... 8 3.1. Test equipment ............................................................................................................................ 8 3.2. Block diagram of test setup ......................................................................................................... 8 3.3. Limits .......................................................................................................................................... 8 3.4. Test Procedure ............................................................................................................................. 8 3.5. Test Result ................................................................................................................................... 9 4. 20dB Bandwidth and 99% Bandwidth ...................................................................................... 10 4.1. Test equipment .......................................................................................................................... 10 4.2. Block diagram of test setup ....................................................................................................... 10 4.3. Limits ........................................................................................................................................ 10 4.4. Test Procedure ........................................................................................................................... 10 4.5. Test Result ................................................................................................................................. 11 4.6. Original test data ....................................................................................................................... 11 5. Carrier Frequency Separation .................................................................................................... 18 5.1. Test equipment .......................................................................................................................... 18 5.2. Block diagram of test setup ....................................................................................................... 18 5.3. Limits ........................................................................................................................................ 18 5.4. Test Procedure ........................................................................................................................... 18 5.5. Test Result ................................................................................................................................. 18 5.6. Original test data ....................................................................................................................... 19 6. Number Of Hopping Channel ................................................................................................... 20 6.1. Test equipment .......................................................................................................................... 20 6.2. Block diagram of test setup ....................................................................................................... 20 6.3. Limits ........................................................................................................................................ 20 6.4. Test Procedure ........................................................................................................................... 20 6.5. Test Result ......................................................................................…

Text truncated - open the document above for the full version.

Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R15Q0731-1E2 Page 53 of 64 13. Test setup photograph Dongguan Dongdian Testing Service Co., Ltd Report No.: DDT-R15Q0731-1E2 Page 54 of 64