AZP-FDQ02TWireless Modem with Serial Interface

i WIRELESS DATA COMMUNICATION MODEM FDQ02T Wireless Modem with Serial Interface Instruction Manual Futaba Corporation Industrial Radio Control ii I Notice This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Any unauthorized changes or modifications to this device not expressly approved by Futaba Corporation could void the user’s authority to operate the device and possibly result in damage to the equipment and/or cause serious or fatal injuries to the operator or nearby personnel. This device is intended to be installed and used in accordance with the instructions contained in this manual. Failure to comply with these instructions could void the user’s authority to operate the device and possibly result in damage to the equipment and/or cause serious or fatal injuries to the operator or nearby personnel. iii II Important Safety Information The list of dangers, warnings and cautions in this section contain important information that will help ensure safe operation of the system. Please read carefully and understand all of these items. All installers, operators and maintenance personnel should read and understand this information before installation, use, or maintenance of the FDQ02T system. The FDQ02T system by itself is not inherently dangerous. HOWEVER, WHEN THE FDQ02T IS CONNECTED TO OTHER EQUIPMENT FOR THE PURPOSE OF CONTROL, SAFETY AND ALL POSSIBLE ASSOCIATED DANGERS MUST ALWAYS BE GIVEN THE UTMOST CONSIDERATION DURING SYSTEM INTEGRATION, DESIGN, INSTALLATION, AND USE. The FDQ02T system may be used in virtually unlimited applications. Many of these associated systems can, by themselves, pose a mechanical, electrical or other hazard to operators and other persons or equipment. To address all possible applications and associated safety hazards in this manual would be impossible. The warnings below and throughout this manual give information that will allow safe installation and use the modem system applications. If you have questions regarding the safety of your specific application, please contact the appropriate people for help. Your Futaba sales representative, representatives of the equipment being controlled, and the technical support staff at local branch of Futaba Corporation are among those who can provide assistance with your safety concerns. The following warnings are included in the lists that follow but warrant repetition here: In installations where the FDQ02T system is used to control motion or operation of potentially dangerous equipment, it is imperative for safety that all operators and installers be thoroughly trained in the normal function of that equipment before attempting to control it remotely with the FDQ02T system. To help ensure safe operation of the equipment, the FDQ02T system must be connected so that it will operate in a fail-safe way. In other words, the equipment being controlled should stop or return to its safest state in the absence of a control signal or total loss of RF transmission from the FDQ02T system. Our system uses one of the most reliable methods available to transmit data using radio signals. Many factors can affect a radio signal that may block it or interfere enough to disrupt regular transmission. Because of this, equipment motion or dangerous electrical current, for example, that continues during a loss-of-signal condition could be very dangerous. iv Four symbols are used in the margin of the following section and throughout the manual to indicate the level of hazard or information listed. The symbols are defined as follows: Indicates a hazard that will cause severe personal injury, death, or substantial property damage if the warning is ignored. Indicates a hazard that can cause severe personal injury, death, or substantial property damage if the warning is ignored. Indicates a hazard that will or can cause minor personal injury, or property damage if the warning is ignored. Indicates installation, operation, or maintenance information that is important but not hazard-related. Please read the following safety information carefully. Some of these notices are duplicated throughout the manual, in areas of associated content, for your benefit. II.I General Safety Hazards and Notes Improper installation and/or operation of the FDQ02T system can cause serious or fatal injuries to the operator or nearby persons and cause damage to the FDQ02T system, and any equipment it is used to control. Please read and understand this manual completely and the manual of all equipment being controlled before attempting to operate or install this system. Always keep this manual at a location readily accessible to anyone operating the system and related equipment. Ensure that all operators have read and understood this manual, especially all safety and operation procedures contained in it. Please refer to the section in this manual titled How to Obtain Help for the contact that can supply additional manuals or answers to questions not covered in this manual. If this product is passed on to a different user, be sure that this manual accompanies the product. Be certain that the installer of t…

Text truncated - open the document above for the full version.

Futaba Corporation Wireless Modem with Serial Interface FCC ID: AZP-FDQ02T Figure 1 Wireless Modem with Serial Interface, General Appearance (Front View) Figure 2 Wireless Modem with Serial Interface, General Appearance (Back View) Futaba Corporation Wireless Modem with Serial Interface FCC ID: AZP-FDQ02T Figure 3 Antenna Type A, General Appearance Figure 4 Antenna Type B, General Appearance (Side View) Futaba Corporation Wireless Modem with Serial Interface FCC ID: AZP-FDQ02T Figure 5 Antenna Type B, General Appearance (Side View)

Futaba Corporation Wireless Modem with Serial Interface FCC ID: AZP-FDQ02T ID Label Format and Location z Label Format z Label Placement Location PROPOSED FCC ID LABEL FOR HOST DEVICE <Brand Name> This device contains FCC ID: AZP-FDG02T

Futaba Corporation Wireless Modem with Serial Interface FCC ID: AZP-FDQ02T Figure 1 Wireless Modem with Serial Interface, General Appearance (Front View) Figure 2 Wireless Modem with Serial Interface, General Appearance (Back View) Futaba Corporation Wireless Modem with Serial Interface FCC ID: AZP-FDQ02T Figure 3 Wireless Modem with Serial Interface, General Appearance (Top Cover Removed) Figure 4 Wireless Modem with Serial Interface, Internal View Futaba Corporation Wireless Modem with Serial Interface FCC ID: AZP-FDQ02T Figure 5 Wireless Modem with Serial Interface, Internal View (IT122 Board Removed) Figure 6 Wireless Modem with Serial Interface, Internal View (IT143 Board / Component Side) Futaba Corporation Wireless Modem with Serial Interface FCC ID: AZP-FDQ02T Figure 7 Wireless Modem with Serial Interface, Internal View (IT143 Board / Foil Side) Figure 8 Wireless Modem with Serial Interface, Internal View (IT122 Board and Shield) Futaba Corporation Wireless Modem with Serial Interface FCC ID: AZP-FDQ02T Figure 9 Wireless Modem with Serial Interface, Internal View (IT122 Board / Front View) Figure 10 Wireless Modem with Serial Interface, Internal View (IT122 Board / Back View) Futaba Corporation Wireless Modem with Serial Interface FCC ID: AZP-FDQ02T Figure 11 Antenna Type A, General Appearance Figure 12 Antenna Type A, Internal View (Cover Removed) Futaba Corporation Wireless Modem with Serial Interface FCC ID: AZP-FDQ02T Figure 13 Antenna Type B, General Appearance (Side View) Figure 14 Antenna Type B, General Appearance (Side View) Futaba Corporation Wireless Modem with Serial Interface FCC ID: AZP-FDQ02T Figure 15 Antenna Type B, Internal View (Antenna Board Removed) Figure 16 Antenna Type B, Internal View (Antenna Board / Front View)

FDQ02T 1 -6- 3 Antenna Type A 4 Antenna Type B

FCC ID. AZP-FDQ02T Page 1 of 90 Audix Corporation Report No. EM-F950150 TEST REPORT FOR CANADA CERTIFICATION On Behalf of Futaba Corporation Wireless Modem with Serial Interface Model No.：FDQ02T FCC ID：AZP-FDQ02T Prepared for : Futaba Corporation 1080 Yabutsuka Chosei-son Chosei-gun Chiba, 299-4395 Japan. Prepared by : Audix Corporation Technical Division EMC Department No. 53-11, Tin-Fu Tsun, Lin-Kou, Taipei County, Taiwan, R.O.C. Tel : (02) 2609-9301, 2609-2133 Fax: (02) 2609-9303 File Number ： EM950399 Report Number ： EM-F950150 Date of Test ： May 02 ~ 05, 2006 Date of Report ： May 09, 2006 FCC ID. AZP-FDQ02T Page 2 of 90 Audix Corporation Report No. EM-F950150 TABLE OF CONTENTS Description Page TEST REPORT CERTIFICATION .......................................................................................................4 1.GENERAL INFORMATION ...........................................................................................................5 1.1. Description of Device (EUT).................................................................................................................. 5 1.2. Tested Supporting System Details .......................................................................................................... 6 1.3. Description of Test Facility .................................................................................................................... 7 1.4. Measurement Uncertainty....................................................................................................................... 7 2.CONDUCTED EMISSION MEASUREMET.................................................................................8 2.1. Test Equipment ....................................................................................................................................... 8 2.2. Block Diagram of Test Setup.................................................................................................................. 8 2.3. Conducted Emission Limits (§15.207) ................................................................................................... 8 2.4. Operating Condition of EUT .................................................................................................................. 9 2.5. Test Procedure ........................................................................................................................................ 9 2.6. Test Results............................................................................................................................................. 9 3.RADIATED EMISSION MEASUREMENT ................................................................................14 3.1. Test Equipment ..................................................................................................................................... 14 3.2. Test Setup ............................................................................................................................................. 14 3.3. Radiated Emission Limits (§15.209) .................................................................................................... 15 3.4. Operating Condition of EUT ................................................................................................................ 15 3.5. Test Procedure ...................................................................................................................................... 16 3.6. Test Results........................................................................................................................................... 16 4.6dB BANDWIDTH MEASUREMENT .........................................................................................66 4.1. Test Equipment ..................................................................................................................................... 66 4.2. Block Diagram of Test Setup................................................................................................................ 66 4.3. Specification Limits (§15.247(a)(2)) .................................................................................................... 66 4.4. Operating Condition of EUT ................................................................................................................ 66 4.5. Test Procedure ...................................................................................................................................... 66 4.6. Test Results........................................................................................................................................... 67 5.MAXIMUM PEAK OUTPUT POWER MEASUREMENT .......................................................70 5.1. Test Equipment ..................................................................................................................................... 70 5.2. Block Diagram of Test Setup................................................................................................................ 70 5.3. Specification Limits (§15.247(b)-(3))................................................................................................... 70 5.4. Operating Condition of EUT ................................................................................................................ 70 5.5. Test Procedure ...................................................................................................................................... 70 5.6. Test Results........................................................................................................................................... 71 6.EMISSION LIMITATIONS MEASUREMENT ..........................................................................72 6.1. Test Equipment ..................................................................................................................................... 72 6.2. Block Diagram of Test Setup...…

Text truncated - open the document above for the full version.

FCC ID. AZP-FDQ02T Page 82 of 90 Audix Corporation Report No. EM-F950150 10. PHOTOGRAPHS 10.1. Photos of Conducted Emission Measurement Test Antenna: Antenna Type A FRONT VIEW OF CONDUCTED MEASUREMENT BACK VIEW OF CONDUCTED MEASUREMENT FCC ID. AZP-FDQ02T Page 83 of 90 Audix Corporation Report No. EM-F950150 Test Antenna: Antenna Type B FRONT VIEW OF CONDUCTED MEASUREMENT BACK VIEW OF CONDUCTED MEASUREMENT FCC ID. AZP-FDQ02T Page 84 of 90 Audix Corporation Report No. EM-F950150 10.2. Photos of Radiated Measurement at Semi-Anechoic Chamber 10.2.1. Frequency Range: 30MHz to 1GHz Test Antenna: Antenna Type A FRONT VIEW OF RADIATED MEASUREMENT BACK VIEW OF RADIATED MEASUREMENT FCC ID. AZP-FDQ02T Page 85 of 90 Audix Corporation Report No. EM-F950150 Test Antenna: Antenna Type B FRONT VIEW OF RADIATED MEASUREMENT BACK VIEW OF RADIATED MEASUREMENT FCC ID. AZP-FDQ02T Page 86 of 90 Audix Corporation Report No. EM-F950150 10.2.2. Frequency Range: Above 1GHz Test Antenna: Antenna Type A FRONT VIEW OF RADIATED MEASUREMENT BACK VIEW OF RADIATED MEASUREMENT FCC ID. AZP-FDQ02T Page 87 of 90 Audix Corporation Report No. EM-F950150 Test Antenna: Antenna Type B FRONT VIEW OF RADIATED MEASUREMENT BACK VIEW OF RADIATED MEASUREMENT FCC ID. AZP-FDQ02T Page 88 of 90 Audix Corporation Report No. EM-F950150 10.3. Photo of 6dB Bandwidth Measurement 10.4. Photo of Maximum Peak Output Measurement FCC ID. AZP-FDQ02T Page 89 of 90 Audix Corporation Report No. EM-F950150 10.5. Photo of Emission Limitations Measurement 10.6. Photo of Band Edges Measurement FCC ID. AZP-FDQ02T Page 90 of 90 Audix Corporation Report No. EM-F950150 10.7. Photo of Power Spectral Density Measurement