AZPR3006SB-24GRadio Control

Applicable systems: Futaba T-FHSS Air-2.4GHz system transmitter R3006SB T-FHSS Air-2.4GHz Bidirectional Communication System S.BUS2 / S.BUS Port and 6 Channels for Conventional System Receiver Compliance Information Statement (for U.S.A.) This device, trade name Futaba Corporation, model number R3006SB, complies with part15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION: To assure continued FCC compliance: 1. Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. 2. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To meet the RF exposure requirements of the FCC this device shall not be co-located with another transmitting device. The responsible party of this device compliance is: Futaba Service Center 3002 N Apollo Drive Suite 1, Champaign, IL 61622 U.S.A. TEL (217)396-6970 or E-mail: [email protected] (Support) R3006SB Specifications T-FHSS Air-2.4GHz system/S.BUS2 and S.BUS port and 6 channels for conventional system receiver • Dual antenna diversity • Size: 1.7 x 0.98 x 0.35 in. (43.1 x 25.0 x 8.8 mm) • Weight: 0.3 oz. (8.5g) • Power requirement: 4.6V to 7.4V • Battery F/S Voltage: It sets up with a transmitter * Be sure that the battery is the correct size for the amount and type of servos being used. When using a BEC, be sure that it is capable of delivering constant voltage and can accept enough current that will be used by the RX and servos. Do not use a dry cell battery with this system. Thank you for purchasing a Futaba R3006SB T-FHSS Air-2.4GHz compatible receiver. The R3006SB receiver features bi-directional communication with a T-FHSS Air-2.4GHz Futaba transmitter using the S.BUS2 port. Using the S.BUS2 port an impressive array of telemetry sensors may be utilized. It also includes both standard PWM output ports and S.BUS output ports. LED Indication GreenRedStatus OffSolidNo signal reception SolidOffReceiving signals Alternate blinkUnrecoverable error (EEPROM, etc.) (Antenna installation) 90 ̊ Please refer the table below for LED status vs receiver's condition. 1M23N174xx S.BUS2 port S.BUS port (SB/6） (SB2/B） S.BUS Servo S.BUS Gyro Mode switch Antenna LED Servo forconventional system Channel1 output Channel6 output Battery to SB2/B R3006SB Telemetry Sensor S.BUS HUB S.BUS HUB S.BUS HUB S.BUS HUB Telemetry Sensor Telemetry Sensor Telemetry Sensor Telemetry Sensor *It's necessary to change it to Mode B (S.BUS) Usage precaution • Futaba T-FHSS Air system does not work with current Futaba T- FHSS / S-FHSS / FHSS / FASST / FASSTest system. • The R3006SB receiver can only be used with T-FHSS Air capable transmitters. WARNING Changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The R3006SB receiver should be protected from vibration by foam rubber, Velcro or similar mounting methods. Protect from moisture. Keep away from conductive materials to avoid short circuits. Antenna installation precaution Don't cut or bundle the receiver antenna wire. Don't bend the coaxial cable. It causes damage. The antennas must be mounted in such a way to assure they are strain relieved. Keep the antenna as far away from the motor, ESC and other noise sources as you possibly can. Be sure that the two antennas are placed at 90 degrees to each other. • The R3006SB has two antennas. In order to maximize signal reception and promote safe modeling Futaba has adopted a diversity antenna system. This allows the receiver to obtain RF signals on both antennas and fly problem-free. Antenna installation for carbon fuselage WARNING You must leave 30mm at the tip of the antenna fully exposed. The ex- posed antenna should be secured so that it cannot move around or back inside of your aircraft. S.BUS2 precaution DANGER Don't connect a connector, as shown right. • It will be a short-circuit, if it connected in this way. A short circuit across the battery terminals may cause abnormal heat, fire and burning. Don't connect servo for conventional system to S.BUS/S.BUS2 port. • Digital servo for conventional system → It does not operate. • Analog servo → It may cause abnormal heat, fire and burning. WARNING Only S.BUS2 capable devices may be connected the S.BUS2 port. Standard S.BUS servos and gyros should not be connected the S.BUS2 port. (Typical installation) Receiver DANGER Do not insert either a switch or battery in this manner. 本產品符合低功率電波輻射性電機管理辦法 第十二條、第十四條等條文 規定 1. 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均 不得擅自變更頻率、加大功率或變更原設計之特性及功能。 2. 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干 擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通 信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通 信或工業 , 科學及醫療用電波輻射性電機設備之干擾。 WARNING Do not perform the linking procedure while the motor's main wire con- nected or the engine is operating as it may result in serious injury. When the linking is complete, please cycle the receiver power and en- sure the receiver is properly linked to the transmitter. Please power up your system in this order. Transmitter first, followed by the receiver. FUTABA CORPORATION 1060 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan Phone: +61 475 32 6962, Facsimile: +61 475 32 6963 Link to the transmitter Easy Link ID allows T-FHSS Air receivers to link to compatible transmitter without pressing the link button on the receiver. 1 Bring the transmitter and the receiver close to each other, within 20 inches (half meter). 2 Turn on the transmitter. Place the transmitter into the receiver linking mode. 3 Turn on the receiver. 4 The receiver will wait for the linking process to begin for 3 seconds. Following that it will return to the normal operation mode. 5 When the LED of the receiver changes from blinking red to solid green, …

Text truncated - open the document above for the full version.

Futaba Corporation Radio Control FCC ID. : AZPR3006SB-24G EUT External Photos Figure 1 General Appearance (Front and Side View) Figure 2 General Appearance (Back and Side View)

Futaba Corporation Radio Control FCC ID. : AZPR3006SB-24G FCC ID Label Location z Label Placement Location z FCC ID Label Format FCC ID Label Placement Location

Futaba Corporation Radio Control FCC ID. : AZPR3006SB-24G EUT Internal Photos Figure 3 Internal View (Removed Cover) Figure 4 Internal View (Main Board, Front View) Futaba Corporation Radio Control FCC ID. : AZPR3006SB-24G Figure 5 Internal View (Main Board, Back View)

Declaration of Compliance FCC ID: AZPR3006SB-24G Product Name: Radio Control Model No: R3006SB In Radio Technology: T-FHSS Modulation Futaba Corporation declares that the product described above has been evaluated and found to comply with the RF exposure limits for humans, as specified based on ANSI/FCC recommendation. Based on safety distance 20cm, the antenna gain is -5.16 dBi, and the power output is 24.378mW, the power density is 0.0015mW/cm^2. RF Exposure Calculations: S = (P * G) / (4* π * r^2) or r = (P * G) / (4 * π * S) Where S = Power Density in mW/cm^2 P = 13.87dBm = 24.378mW G = -5.16 dBi = 0.305 Numerical r = 20cm S = 24.378*0.305 / 4*π* 20^2 = 0.0015mW/cm^2 Sincerely Yours, ____________________________________ Mr. Ben Cheng Manager AUDIX Technology Corporation

Page 1 of 32 AUDIX Technology Corp. Tel: +886 2 26099301 No. 53-11, Dingfu, Linkou, Dist., Fax: +886 2 26099303 New Taipei City244,Taiwan File Number: C1M1503324 Report Number: EM-F150185 This test report may be reproduced in full only. The documentmay only be updated by AUDIX TechnologyCorp. personnel AnychangeswillbenotedintheDocumentHistorysectionofthereport. FCC 15.247 DSS 2.4GHz Report for FUTABA Corporation 1080 YabutsukaChosei-son Chosei-gun Chiba, 299-4395 Japan. Brand : Futaba Product Name : Radio Control Model Name : R3006SB FCC ID : AZPR3006SB-24G Page 2 of 32 AUDIX Technology Corp. Tel: +886 2 26099301 No. 53-11, Dingfu, Linkou, Dist., Fax: +886 2 26099303 New Taipei City244,Taiwan File Number: C1M1503324 Report Number: EM-F150185 This test report may be reproduced in full only. The documentmay only be updated by AUDIX TechnologyCorp. personnel AnychangeswillbenotedintheDocumentHistorysectionofthereport. TABLE OF CONTENTS Description Page TEST REPORT CERTIFICATION ............................................................................................ 4 1. REPORT HISTORY............................................................................................................. 5 2. SUMMARY OF TEST RESULTS ...................................................................................... 6 3. GENERAL INFORMATION .............................................................................................. 7 3.1. Description of EUT .................................................................................................................... 7 3.2. EUT Specifications Assessed in Current Report ..................................................................... 8 3.3. Antenna Information ................................................................................................................. 8 3.4. Tested Supporting System List ................................................................................................. 9 3.5. Setup Configuration ................................................................................................................ 10 3.6. Operating Condition of EUT .................................................................................................. 10 3.7. Description of Test Facility ..................................................................................................... 10 3.8. Measurement Uncertainty ...................................................................................................... 11 4. MEASUREMENT EQUIPMENTLIST ............................................................................ 12 4.1. Radiated Emission Measurement ........................................................................................... 12 4.2. RF Conducted Measurement .................................................................................................. 12 5. CONDUCTED EMISSION MEASUREMET .................................................................. 13 6. RADIATED EMISSION MEASUREMENT ................................................................... 14 6.1. Block Diagram of Test Setup .................................................................................................. 14 6.2. Radiated Emission Limits ....................................................................................................... 15 6.3. Test Procedure ......................................................................................................................... 15 6.4. Measurement Result Explanation .......................................................................................... 16 6.5. Test Results ............................................................................................................................... 16 7. 20dB BANDWIDTH MEASUREMENT .......................................................................... 26 7.1. Block Diagram of Test Setup .................................................................................................. 26 7.2. Specification Limits ................................................................................................................. 26 7.3. Test Procedure ......................................................................................................................... 26 7.4. Test Results ............................................................................................................................... 26 8. CARRIER FREQUENCY SEPARATION MEASUREMENT ..................................... 27 8.1. Block Diagram of Test Setup .................................................................................................. 27 8.2. Specification Limits ................................................................................................................. 27 8.3. Test Procedure ......................................................................................................................... 27 8.4. Test Results ............................................................................................................................... 27 9. TIME OF OCCUPANCY MEASUREMENT .................................................................. 28 9.1. Block Diagram of Test Setup .................................................................................................. 28 9.2. Specification Limits ................................................................................................................. 28 9.3. Test Procedure ......................................................................................................................... 28 10. NUMBER OF HOPPING CHANNELS MEASUREMENT ........................................ 29 10.1. Block Diagram of Test Setup .................................................................................................. 29 10.2. Specification Limits .......................................................................…

Text truncated - open the document above for the full version.

APPENDIX B AUDIX Technology Corp. Tel: +886 2 26099301 No. 53-11, Dingfu, Linkou, Dist., Fax: +886 2 26099303 New Taipei City244, Taiwan File Number: C1M1503324 Report Number: EM-EM-F150185 This test report may be reproduced in full only. The document may only be updated by AUDIX Technology Corp. personnel Any changes will be noted in the Document History section of the report. APPDNDIX B TEST PHOTOGRAPHS (Model: R3006SB) APPENDIX A-Page 1 of 2 AUDIX Technology Corp. Tel: +886 2 26099301 No. 53-11, Dingfu, Linkou, Dist., Fax: +886 2 26099303 New Taipei City244, Taiwan File Number: C1M1503324 Report Number: EM-EM-F150185 This test report may be reproduced in full only. The document may only be updated by AUDIX Technology Corp. personnel Any changes will be noted in the Document History section of the report. B.1 Radiated Measurement at Semi-Anechoic Chamber Frequency Below 1GHz Frequency Above 1GHz APPENDIX A-Page 2 of 2 AUDIX Technology Corp. Tel: +886 2 26099301 No. 53-11, Dingfu, Linkou, Dist., Fax: +886 2 26099303 New Taipei City244, Taiwan File Number: C1M1503324 Report Number: EM-EM-F150185 This test report may be reproduced in full only. The document may only be updated by AUDIX Technology Corp. personnel Any changes will be noted in the Document History section of the report. B.2 RF Conducted Measurement