B4Z-723-TCVRSB2000 Transceiver

1


    ITI Part No. 60-764-01-95R Installation Instructions Document Number: 466-1565-01 Rev. A June 2000 Product Summary The SuperBus 2000 RF Receiver Module is a UL listed device that adds or expands panel wireless zone capacity. See the specific panel Installation Instructions for complete UL requirements for the system you are installing. The receiver is compatible with all ITI 319.5 MHz (crystal and SAW) Learn Mode ™ wireless sensors and touchpads, and can be mounted inside the panel cabinet or located up to 2,800 feet away from the panel (see Table 2). It receives information from wireless sensors and touchpads then sends the data to the panel via the SuperBus 2000 digital data bus. Power for the module is provided by the panel. Receivers are available in 16-zone (-16Z), 32-zone (-32Z), or panel maximum (-MAX) capacities. SuperBus 2000 vs. SuperBus SuperBus 2000 panels have the ability to auto-address mod- ule unit numbers. When the panel is powered up, the panel automatically reads the unique SuperBus 2000 device ID number and assigns a unit number to the module. This elim- inates manually setting DIP switches and the chance of identical unit number conflicts. SuperBus panels communicate with SuperBus 2000 modules but require the module unit number to first be set manually using DIP switches. The SuperBus 2000 RF Receiver Module features: qSpatial diversity, which minimizes wireless signal nulls or dead spots. qCompatibility with all ITI 319.5 MHz (crystal or SAW) Learn Mode ™ wireless sensors, touchpads, and sirens. qBackward compatibility with SuperBus panels. q1,500 feet nominal, open air receiving range. Figure 1 shows the receiver module components and Table 1 describes them. Figure 1. RF Receiver Module Components Table 1. Component Descriptions ComponentFunction AntennasProvide communication with wireless devices. SuperBus 2000 Device ID Number Label Identifies unique module SuperBus 2000 device ID number (SuperBus 2000 panels). Receiver Status LEDOn continuously when the receiver is powered. Flashes when an RF signal is received. Unit Number DIP Switches Used for manually setting unit numbers (SuperBus panels). Terminal StripUsed for power and bus connections to panel. 1065G03A.DSF MOUNTING HOLES (3) CIRCUIT BOARD ANTENNA TERMINAL BLOCKS (2) ANTENNAS STATUS LED TERMINAL STRIP UNIT NUMBER DIP SWITCHES ID: XXXXXXXX SUPERBUS 2000 DEVICE ID NUMBER LABEL MAGNET CLIP REED SWITCH HOLDER 8543130A.DS4 2 Installation Guidelines Installation Guidelines Observe the following guidelines when installing the receiver module: qConcord ™ systems can accommodate a maximum of 76 wireless sensors/zones. qIn Concord systems, up to 16 SuperBus 2000 devices can be connected to the panel (SuperBus 2000 Touch- pads, Receivers, HIMs, HOMs, ESMs, etc.). qEach bus device must have a different unit number. qLeave 10-inches above the module for the antennas. qIf mounting the module inside the panel cabinet, use a support standoff included with the Concord panel. If mounting the module away from the panel, use the wire length guidelines in Table 2. qAvoid areas that are likely to expose the module to moisture. qAvoid areas with excessive metal or electrical wiring, including furnace and utility rooms. If unavoidable, mount on or near metal with the anten- nas extending above the metallic surfaces, as shown in Figure 2. Figure 2. Mounting on or Near Metal Tools and Supplies qScrewdrivers qDrill with bits qMounting screws and anchors (included) q2 antennas (included) q4-conductor, 22-gauge or larger, stranded wire qSupport standoff (included with Concord cabinet) q¼-inch press-fit reed switch and magnet (not included) qSmall hammer Installation The module can be mounted inside the panel cabinet or on any interior wall (protected from the elements). CAUTION To prevent damaging the panel or module, remove the panel AC power transformer and disconnect the backup battery before installation. CAUTION You must be free of static electricity before handling circuit boards. Wear a grounding strap or touch a bare metal surface to discharge static electricity. Figure 3. Removing the Cover To mount the module on a wall: 1.Remove the panel AC power transformer and discon- nect the backup battery. 2.Remove the module cover and set it aside (Figure 3). 3.Hold the base against the mounting surface and mark the three mounting holes (Figure 1). Remember to leave at least 10 inches above the base for the antennas. 4.Drill holes and insert the appropriate anchors. 5.Secure the back-plate to the wall with included pan- head screws. To mount the module in a Concord panel cabinet: 1.Remove the panel AC power transformer and discon- nect the backup battery. 2.Remove and discard the module cover (Figure 3). Table 2. Maximum Module Wire Lengths Wire Gauge (Unshielded or Shielded) Max. Wire Length Between Module and Concord Panel 182,800 feet 221,100 feet METAL METAL 8836G02A.DS4 PRESS DOWN HERE AND PULL AWAY FROM BASE 8543118A.DSF 3 Concord Panel Wiring 3.Insert a support standoff shown in Figure 4 (supplied with panel) into the panel circuit board location shown in Figure 5. Figure 4. Support Standoff 4.Slide the module back-plate into the two top mounting clips located on the top-right side of the cabinet and onto the right-side support on the cabinet (see Figure 5). Figure 5. Mounting the module in a Concord Cabinet 5.Push the lower-left corner of the module onto the sup- port standoff (see detail in Figure 5). Connecting the Antennas to the Module 1.Loosen the inside terminals of the left and right antenna terminal blocks (see Figure 1). 2.Insert an antenna into each inside terminal. (Insert antennas through cabinet top holes when module is mounted inside panel cabinet.) 3.Tighten the antenna terminal screws. Concord Panel Wiring This section describes how to wire the receiver module to Concord panels. To wire the receiver module to Concord panels: 1.Disconnect the panel power transformer and backup ba…

Text truncated - open the document above for the full version.

GE Security, Inc. EXHIBIT C Block Diagram of Product Power Amp RF Amp Microchip PIC16F73 Microcontroller 319.5 MHz Osc. NEC 8116 Receiver Chip Antenna Switch 01/31/05 4:18 PM FCC ID: B4Z-723-TCVR C:\Documents and Settings\corey.running\My Documents\SB 2000\SB2000 Receivers\60-764\60-764-01- 95R with Transmitter\FCC Report\Exhibit C_Block Diagram.doc

GE Security, Inc. EXHIBIT B External Photographs Figure 1: Picture of the front of the DUT. 01/28/05 1:02 PM FCC ID: B4Z-723-TCVR C:\Documents and Settings\corey.running\My Documents\SB 2000\SB2000 Receivers\60-764\60-764-01- 95R with Transmitter\FCC Report\Exhibit B_External Photo.doc

GE Security, Inc. EXHIBIT A ID Label / Location 01/31/05 2:29 PM FCC ID: B4Z-723-TCVR C:\Documents and Settings\corey.running\My Documents\SB 2000\SB2000 Receivers\60-764\60-764-01- 95R with Transmitter\FCC Report\Exhibit A_ID Label.doc

GE Security, Inc. EXHIBIT H Internal Photographs 01/31/05 3:42 PM FCC ID: B4Z-723-TCVR C:\Documents and Settings\corey.running\My Documents\SB 2000\SB2000 Receivers\60-764\60-764-01- 95R with Transmitter\FCC Report\Exhibit H_Internal Photos.doc GE Security, Inc. Exhibit H_Internal Photos.doc 01/31/05 3:42 PM FCC ID: B4Z-723-TCVR Page 2 of 2

GE Security, Inc. EXHIBIT I Operational Description Product Description This device is a transceiver. It receives signals from existing ITI transmitters or other superbus transceivers. It transmits signals to other compatible ITI receivers. Both the receiver and the transmitter operate 319.5 MHz. A hardwire bus provides a data link to an external board. There is one possible configurations for the hardwire bus: • A external board may be connected to the 4 position terminal block or 8 position header. 12VDC power is supplied by the external board. The transmitter circuit consists of a 319.5 MHz SAW resonator followed by an amplifier. The transmitter amplifier is connected to the right antenna. The receiver is of the superheterodyne type. It uses a NEC UPC8116G 500 MHz AM/ASK receiver chip. The receiver selects either the right or left antenna. 01/31/05 4:31 PM FCC ID: B4Z-723-TCVR C:\Documents and Settings\corey.running\My Documents\SB 2000\SB2000 Receivers\60-764\60-764-01- 95R with Transmitter\FCC Report\Exhibit I_Operation Desc.doc

GE Security, Inc. GE Security, Inc. SuperBus 2000 Transceiver B4Z-723-TCVR Certification 01/31/05 4:29 PM FCC ID: B4Z-723-TCVR Page 1 of 17 C:\Documents and Settings\corey.running\My Documents\SB 2000\SB2000 Receivers\60-764\60-764-01- 95R with Transmitter\FCC Report\FCC_REPT.DOC GE Security, Inc. Super Board Transceiver B4Z-723-TCVR 01-31-2005 GE Security, Inc. 1275 Red Fox Road Arden Hills, MN 55112 (651) 777-2690 FCC_REPT.DOC 01/31/05 4:29 PM FCC ID: B4Z-723-TCVR Page 2 of 17 GE Security, Inc. 1. INTRODUCTION 4 2. STATEMENT OF COMPLIANCE 4 3. LAB MEASUREMENTS DISCUSSION / TEST NOTES 7 3.1 Test Notes 7 3.1.1 Transmissions shall cease within 5 seconds of activation [ §15.231(a)(2) ] 7 3.1.2 Duty Cycle Correction Factor [§15.231(b)(2) and §15.35(c)] 8 3.1.3 Bandwidth Measurement [ §15.231(c) ] 11 3.1.4 Emissions Measurements 15 3.1.4.1 Radiated Emissions Summary 15 3.1.4.2 FCC Emissions Calculation 15 3.1.4.2.1 Terms 15 3.1.4.2.2 Example Calculation 16 3.1.4.3 Radiated Emissions 16 3.1.4.4 Forbidden Bands 16 FCC_REPT.DOC 01/31/05 4:29 PM FCC ID: B4Z-723-TCVR Page 3 of 17 GE Security, Inc. 1. Introduction This device is a radio transceiver. It receives signals from existing ITI transmitters or other transceivers. It transmits signals to other ITI transceivers or receivers. A hardwire bus provides a data link to an external board or a security panel. 12VDC power is supplied to the device via a hardwire bus connection to an external board.. The transceiver board has a profile, which is 4.0” long by 3.875” wide. We are requesting Certification under FCC Rules, Part 15, Subpart C, Paragraph 15.231. Please send comments/suggestions on the report format to [email protected]. Grantee Code: B4Z 2. Statement of Compliance §2.907 Certification This is an application for certification §2.911 Application a) This is an application and has been filed electronically with form 731. b) All information required has been supplied. c) The applicant has signed the application (electronically). d) The technical data has been signed. (See Radiated Emissions) e) Applicant signature block on electronic form 731 completed by officer of the company or authorized company personnel. f) The appropriate fee has been paid electronically with VISA on **/**/**. §2.915 Grant This application demonstrates that all applicable technical standards have been met and a grant of this application will serve the public interest. FCC_REPT.DOC 01/31/05 4:29 PM FCC ID: B4Z-723-TCVR Page 4 of 17 GE Security, Inc. §2.925 Label Each piece of equipment for which authorization will be granted will be uniquely identified with “FCC ID: B4Z-723-TCVR.” The required statement will appear with the FCC ID on the product and, although not required, in the installation instructions. See Exhibit A, PDF file id_label.pdf §2.947 Measurement Procedure a) The measurement procedure follows ANSI C63.4 procedure. Procedural notes are contained in the laboratory report. d) A list of test equipment used is contained in the laboratory report. §2.948 Description of Measurement Facilities Measurements were performed at TUV Testing Services Open Test Site. The FCC keeps a full description of the measurement facilities on file. TUV’s acceptance and approval is dated as December 5, 1993 in a letter received from the FCC. The address of the test facility is: TUV Product Service 19035 Wild Mountain Road Taylors Falls, MN 55084-1758 Phone: 651-638-0297 Contact: Joel Schneider Test Engineer in Charge See Exhibit F, PDF file Test Photo.pdf for sketch of measurement setup §2.1033 Application for Certification a) Form 731 has been electronically filed on **/**/**. Items that did not apply were left blank. b) This technical report contains the following information where applicable. 1) Full name and mailing address of manufacturer and applicant for certification: GE Security, Inc. 1275 Red Fox Road Arden Hills, MN 55112 2) FCC Identifier: B4Z-723-TCVR FCC_REPT.DOC 01/31/05 4:29 PM FCC ID: B4Z-723-TCVR Page 5 of 17 GE Security, Inc. 3) Copy of installation instructions: See Exhibit G, PDF file: User Manual.pdf 4) Brief Description of circuit functions and device operation: See Exhibit I, PDF file Operation Desc.pdf See Exhibit D, PDF file Schematic.pdf for schematics (page 1) and parts placement (page 2) diagrams. 5) Block Diagram See Exhibit C, PDF file Block Diagram.pdf. 6) Report of the measurements of radiation and conducted emissions: See Exhibit E, PDF file Emissions TUV.pdf 7) Photographs External: See Exhibit B, PDF file External Photo.pdf Internal: See Exhibit H, PDF file Internal Photo.pdf 8) Transition Rules This application is not pursuant to the transition rules of §15.37 9) Emergency Broadcast decoding: This is not applicable to device in this application. 10) Application for direct sequence spread spectrum devices... This is not applicable to device in this application. 11) Application for scanning receivers... This is not applicable to device in this application. c) Composite Systems This is not applicable to device in this application. FCC_REPT.DOC 01/31/05 4:29 PM FCC ID: B4Z-723-TCVR Page 6 of 17 GE Security, Inc. 3. Lab Measurements Discussion / Test Notes 3.1 Test Notes 3.1.1 Transmissions shall cease within 5 seconds of activation [ §15.231(a)(2) ] Transmissions consist of 1 packet, which is controlled by an external board connected to the transceiver. The packet duration is at most 30 mS, see Duty Cycle Correction Factor [§15.231(b)(2) and §15.35(c)] . Transmission duration = 30mS The following plot shows a packet transmission that concludes in less than 5 seconds. 01/31/05 4:29 PM FCC ID: B4Z-723-TCVR Page 7 of 17 C:\Documents and Settings\corey.running\My Documents\SB 2000\SB2000 Receivers\60-764\60-764-01- 95R with Transmitter\FCC Report\FCC_REPT.DOC GE Security, Inc. 3.1.2 Duty Cycle Correction Factor [§15.231(b)(2) and §15.35(c)] The transmitter employs amplitude modulation and transmits 61 bit or 80 bit ITI protocol. The duty cycle correction…

Text truncated - open the document above for the full version.

RADIATED EMISSIONS Test Report #: 0694 Run 1 Test Area: LTS EUT Model #: 55-723-01-D Date: 2/16/04 EUT Serial #: EUT Power: 12 VDC Temperature: 20.0 °C Test Method: 319 MHz TRX Air Pressure: 97.0 kPa Customer: GE Interlogics Rel. Humidity: 25.0 % EUT Description: Super Bus 2000 OEM Transceiver Notes: Data File Name: 0694.dat Page: 1of 3 Tested by: J. C. Sausen Printed Signature Reviewed List of measurements for run #: 1 FREQ LEVEL (dBuV) CABLE / ANT / PREAMP / ATTEN (dB) FINAL (dBuV / m) POL / HGT / AZ (m)(DEG) DELTA1 DELTA2 319.476 MHz 77.8 Pk 1.5 / 14.1 / 0.0 / 0.0 93.4 H / 1.00 / 0 n/a n/a 319.476 MHz 76.9 Pk 1.5 / 14.1 / 0.0 / 0.0 92.5 V / 1.00 / 0 n/a n/a 212.976 MHz 36.15 Qp 1.21 / 11.0 / 0.0 / 0.0 48.36 V / 1.00 / 0 n/a n/a 106.476 MHz 34.2 Qp 0.81 / 9.46 / 0.0 / 0.0 44.47 V / 1.00 / 0 n/a n/a 425.976 MHz 37.85 Pk 1.71 / 16.92 / 0.0 / 0.0 56.48 V / 1.00 / 0 n/a n/a 532.476 MHz 30.05 Pk 1.93 / 18.6 / 0.0 / 0.0 50.58 V / 1.00 / 0 n/a n/a 638.976 MHz 36.35 Pk 2.1 / 20.0 / 0.0 / 0.0 58.45 V / 1.00 / 0 n/a n/a 106.476 MHz 33.85 Pk 0.81 / 9.46 / 0.0 / 0.0 44.12 H / 1.00 / 0 n/a n/a 212.976 MHz 44.7 Pk 1.21 / 11.0 / 0.0 / 0.0 56.91 H / 1.00 / 0 n/a n/a 106.476 MHz 36.35 Pk 0.81 / 9.46 / 0.0 / 0.0 46.62 H / 1.00 / 0 n/a n/a 532.476 MHz 28.45 Pk 1.93 / 18.6 / 0.0 / 0.0 48.98 H / 1.00 / 0 n/a n/a 638.976 MHz 33.65 Pk 2.1 / 20.0 / 0.0 / 0.0 55.75 H / 1.00 / 0 n/a n/a 958.5 MHz 40.35 Pk 2.68 / 23.31 / 24.3 / 0.0 42.04 H / 1.00 / 0 n/a n/a 852.0 MHz 37.5 Pk 2.51 / 22.5 / 24.48 / 0.0 38.04 H / 1.00 / 0 n/a n/a 745.5 MHz 33.8 Pk 2.32 / 21.79 / 24.5 / 0.0 33.41 H / 1.00 / 0 n/a n/a 1.065 GHz 47.65 Pk 2.83 / 26.44 / 39.29 / 0.0 37.64 H / 1.00 / 0 n/a n/a 2.769 GHz 55.4 Pk 4.53 / 31.24 / 43.97 / 0.0 47.19 H / 1.00 / 0 n/a n/a 2.876 GHz 54.05 Pk 4.63 / 31.45 / 44.17 / 0.0 45.97 H / 1.00 / 0 n/a n/a 2.982 GHz 49.35 Pk 4.74 / 31.66 / 44.33 / 0.0 41.43 H / 1.00 / 0 n/a n/a 2.556 GHz 48.55 Pk 4.4 / 30.81 / 43.7 / 0.0 40.06 H / 1.00 / 0 n/a n/a 3.089 GHz 48.4 Pk 4.84 / 31.93 / 44.43 / 0.0 40.74 H / 1.00 / 0 n/a n/a 3.195 GHz 47.25 Pk 4.94 / 32.21 / 44.48 / 0.0 39.92 H / 1.00 / 0 n/a n/a 1.065 GHz 52.7 Pk 2.83 / 26.44 / 39.29 / 0.0 42.68 V / 1.00 / 0 n/a n/a 1.172 GHz 45.7 Pk 2.97 / 26.5 / 40.11 / 0.0 35.06 V / 1.00 / 0 n/a n/a 1.278 GHz 45.9 Pk 3.1 / 26.57 / 40.56 / 0.0 35.01 V / 1.00 / 0 n/a n/a 1.385 GHz 48.75 Pk 3.23 / 26.63 / 41.11 / 0.0 37.49 V / 1.00 / 0 n/a n/a 1.598 GHz 48.75 Pk 3.52 / 27.27 / 41.83 / 0.0 37.71 V / 1.00 / 0 n/a n/a 2.876 GHz 49.65 Pk 4.63 / 31.45 / 44.17 / 0.0 41.57 V / 1.00 / 0 n/a n/a by: Printed Signature RADIATED EMISSIONS Test Report #: 0694 Run 1 Test Area: LTS EUT Model #: 55-723-01-D Date: 2/16/04 EUT Serial #: EUT Power: 12 VDC Temperature: 20.0 °C Test Method: 319 MHz TRX Air Pressure: 97.0 kPa Customer: GE Interlogics Rel. Humidity: 25.0 % EUT Description: Super Bus 2000 OEM Transceiver Notes: Data File Name: 0694.dat Page: 2of 3 Tested by: J. C. Sausen Printed Signature Reviewed List of measurements for run #: 1 FREQ LEVEL (dBuV) CABLE / ANT / PREAMP / ATTEN (dB) FINAL (dBuV / m) POL / HGT / AZ (m)(DEG) DELTA1 DELTA2 Note: TRX in standby / normal operating mode. RCV scan: No supurious emissions detected 30 MHz to 1000 MHz, vert and hor ant. 360 degree EUT rotation and 1m to 4 m antenna ht scans. by: Printed Signature RADIATED EMISSIONS Test Report #: 0694 Run 1 Test Area: LTS EUT Model #: 55-723-01-D Date: 2/16/04 EUT Serial #: EUT Power: 12 VDC Temperature: 20.0 °C Test Method: 319 MHz TRX Air Pressure: 97.0 kPa Customer: GE Interlogics Rel. Humidity: 25.0 % EUT Description: Super Bus 2000 OEM Transceiver Notes: Data File Name: 0694.dat Page: 3of 3 Tested by: J. C. Sausen Printed Signature Reviewed by: Printed Signature Graph: 100MHz1GHz10GHz 30 40 50 60 70 80 90 100 Qp-measurements Pk-measure ments

GE Security, Inc. EXHIBIT F Test Setup Sketch for Radiated Emissions Receiving Antenna 1 Meter EUT 0.8 Meters 3 Meters 01/28/05 2:22 PM FCC ID: B4Z-723-TCVR C:\Documents and Settings\corey.running\My Documents\SB 2000\SB2000 Receivers\60-764\60-764-01- 95R with Transmitter\FCC Report\Exhibit F_Test Photo.doc