B4Z-785B-ALTPDialog QS1000 Remote Station

1 D†‡hyyh‡v‚ D†‡…ˆp‡v‚† ZZZ*(,QWHUORJL[FRP B@D‡r…y‚tv‘ 9 Product Summary The Dialog™ QS1000 Allegro Remote Station is a wireless wall-mount remote station designed to provide remote security system control and status checking. The Remote Station allows the user to perform the following functions: •Arming and Disarming •Activating Police, Auxiliary and Fire Panic Alarms •Checking of System Status The remote station has the following features: •One Hardwire Input •Built-in Siren •Wall Tamper •Custom Liquid Crystal Display (LCD) •Armed and Ready LEDs ProgrammingThe following steps describe the general process for programming (learning) the remote station into panel memory. Refer to the specific panel Installation Instructions or Reference Manual for complete programming details.
To program the remote station into the system: 1. Enter the appropriate code to access the panel menus. 2. Enter the panel Learn/Add Sensors/Devices menu. 3. Change the sensor number if necessary. 4. Press and hold both Police Panic buttons on the remote station.
To set the volume of status beeps from the remote station: 1. Press and hold the 8 button. The remote station will beep every 2 seconds. 2. Release the button when the desired volume is reached. MountingUse the following procedure to mount remote station to the wall or wall studs.
To mount the remote station: 1. Remove the remote station from the back mounting plate by lifting the tab located on the top and pulling back. 2. Remove the wiring knockout. 3. Feed all device wires through the knockout and place the back mounting plate in position against the wall. 4. Level the back mounting plate and mark the top and bottom mounting holes. You must be free of static electricity before handling circuit boards. Wear a grounding strap or touch a bare metal surface to discharge static electricity. Static Tab Antenna (Standard) Figure 1. Tab location 9‚pˆ€r‡ Iˆ€ir…) #%%!( Sr‰ 6 Trƒ‡r€ir… !" QS@GDHDI6S` Preliminary 9/19/03 9vhy‚tRT  6yyrt…‚Sr€‚‡rT‡h‡v‚ Qh…‡ I‚ %('!($S 2 Allegro Remote Station Installation Instructions Preliminary 9/19/03 Note The wiring knockout is approximately the same width as a wall stud. If mounting the remote station to a wall stud be sure you have enough room to feed the wires through the knock- out. 5. Install anchors where studs are not present. 6. Partially insert a screw into the top mounting hole location then hang the back mounting plate on the screw. 7. Recheck for level, insert the lower screw, and tighten both mounting screws. 8. Install the antenna. There are three antenna options to choose from: •Standard Range- Leave the antenna as is. •Extended Range - Attach the optional antenna housing (included in the accessory pack) to the remote station. a.Push the antenna housing down into the top right hole of the remote station until it snaps into place (see Figure 2). b.Remove the antenna loop from the last clip on the remote station cabinet and insert it into the antenna housing. •Longest Range - Hang the antenna in the wall. a.When you mark the back mounting plate’s two mounting holes, also mark where the antenna hole is (see Figure 2 for antenna wire hole location). b.Where the antenna hole was marked, drill a hole into the wall. c.Remove the antenna loop (see Figure 2) from the remote station cabinet clips and feed through the antenna hole and down into the wall. Figure 2. Antenna configurations 9. Place the remote station cabinet into the back mounting plate and snap into place. Connecting Detection Devices to the remote station The remote station has one hardwire input. The input is supervised using a 2.2 k Ohm, end-of-line (EOL) resis- tor (included with the remote station) at the last device on the circuit. It accepts normally closed (N/C) detec- tion devices. Figure 3 shows the typical wiring for a N/ C door/window intrusion detection. The maximum loop resistance for each zone input is 300 ohms, plus the 2.2 k Ohm EOL resistor. Important ! The 2.2 kOhm EOL resistor must be installed across termi- nal 3 and 4 even when no detection device is connected. If this is not done the panel will indicate the zone is open. Clips Antenna Loop 6087495g02a.dsf Antenna Housing Push Down Into Panel Antenna Wiring Optional Antenna Housing Antenna Wire Hole Wire Clip Mounting Knockout Tam p er Switch Holes Wiring Hole (Longest Range) (Extended Range) (Standard Range) Panel Terminals Normally Closed (N/C) Contacts In Series 34 Figure 3. Wiring N/C Intrusion Detection devices 2.2 k Ohm EOL Resistor 49-467 3Allegro Remote Station Installation Instructions Preliminary 9/19/03 Connecting the AC Power Transformer The remote station must be powered by a UL approved transformer. Connect the power trans- former to the panel as shown in Figure 4. Note In Canada, use the AC power transformer without a securing tab, (part no. 22- 117 -CN ). Connecting the Backup Battery Pack The remote station will receive its primary power from an AC class II transformer. In the event of an AC power failure, the remote station will be powered by a battery pack containing four rechargeable NiCd batteries. Figure 5. Connecting the Battery Pack
To connect the backup battery pack: 1. Remove the panel housing from the back mounting plate by lifting the tab located on the top of the remote station and pulling back. 2. Slide the battery pack into the space provided on the back of the remote station (Figure 5). Note Be sure to run the battery pack wires below the battery and through the wire chan- nel. 3. Plug the battery pack lead into the slot provided next to the wire terminals (Figure 5). 4. Replace the remote station housing on the back mounting plate and snap into place. Note Verify the front door is in place before replacing the panel on the mounting plate. It is not possible to attach the door after the panel is secured to the mounting plate. Powering Up the Remote Station After connecting and wiring all devices to the panel, you are ready to …

Text truncated - open the document above for the full version.

9/12/03 To: FCC Re: Application for B4Z-785B-ALTP The product contained in this application uses the same circuit board, hardware design, and enclosure as the FCC approved product, Allegro security control panel (FCC ID: B4Z-785B-ALGRO). We’ve submitted this application due to differences between this product and the Allegro security panel in the following areas: • FCC label/location • Length of the longest transmission [§15.2319(a)(2)] • Supervisory transmissions occurring at regular predetermined intervals [§15.2319(a)(3)] • User Manual.

Nov. 10 th , 2003 To: Federal Communications Commission Re: Confidentiality Request Please withhold documents marked Confidential in our application for B4Z- 785B-ALTP from the general public. These documents contain company proprietary and sensitive information. Thank you, John Bergman Vice President of Wireless Engineering GE Interlogix

GE Interlogix, Inc 09/11/03 5:33 PM FCC ID: B4Z-785B-ALTP \\MSPFPS01\Dept\Engineer\eng_panel\proj\Allegro\Two-way touchpad\FCC\extern.DOC EXHIBIT B External Photographs

GE Interlogix, Inc 09/11/03 5:31 PM FCC ID: B4Z-785B-ALTP \\MSPFPS01\Dept\Engineer\eng_panel\proj\Allegro\Two-way touchpad\FCC\id_label.doc EXHIBIT A ID Label / Location

GE Interlogix, Inc 09/11/03 5:30 PM FCC ID: B4Z-785B-ALTP \\MSPFPS01\Dept\Engineer\eng_panel\proj\Allegro\Two-way touchpad\FCC\intern.DOC EXHIBIT H Internal Photographs Interactive Technologies Inc intern.DOC 09/11/03 5:30 PM FCC ID: B4Z-760A-EFOB Page 2 of 2

GE Interlogix, Inc 09/19/03 4:28 PM FCC ID: B4Z-785B-ALTP Page 1 of 25 \\MSPFPS01\Dept\Engineer\eng_panel\proj\Allegro\Two-way touchpad\FCC\FCC_REPT.DOC GE Interlogix, Inc. Dialog QS1000 Remote Station B4Z-785B-ALTP Certification GE Interlogix, Inc. FCC_REPT.DOC 09/19/03 4:28 PM FCC ID: B4Z-785B-ALTP Page 2 of 25 Dialog QS1000 Remote Station B4Z-785B-ALTP 9/8/2003 GE Interlogix, Inc. 2266 North Second Street North Saint Paul, MN 55109 (651) 777-2690 GE Interlogix, Inc. FCC_REPT.DOC 09/19/03 4:28 PM FCC ID: B4Z-785B-ALTP Page 3 of 25 1. INTRODUCTION4 2. STATEMENT OF COMPLIANCE4 3. LAB MEASUREMENTS DISCUSSION / TEST NOTES7 3.1 Test Notes7 3.1.1 Transmissions shall cease within 5 seconds of activation [ §15.231(a)(2) ]7 3.1.2 Supervisory Calculation [ §15.231(a)(3) ]9 3.1.3 Duty Cycle Correction Factor [§15.231(b)(2) and §15.35(c)]9 3.1.4 Bandwidth Measurement [ §15.231(c) ]12 3.1.5 Emissions Measurements16 3.1.5.1 Radiated Emissions Summary16 3.1.5.2 FCC Emissions Calculation16 3.1.5.2.1 Terms16 3.1.5.2.2 Example Calculation17 3.1.5.3 Radiated Emissions18 3.1.5.4 Forbidden Bands18 GE Interlogix, Inc. FCC_REPT.DOC 09/19/03 4:28 PM FCC ID: B4Z-785B-ALTP Page 4 of 25 1. Introduction This device is a wireless keypad with a transmitter for use in a wireless security system. The unit is powered by an 8VAC Class 2 transformer, and four 1.2V Ni-Cad batteries, used as a back up power supply. The transmitter’s frequency is crystal controlled and is not adjustable by the user. The device measures approximately 3.75” in width, 1.72” in depth and 7.75′′ in height. The unit weighs approximately 8 ounces without batteries. We are requesting Certification under FCC Rules, Part 15, Subpart C, Paragraph 15.231. Please send comments/suggestions on the report format to: [email protected] 2. Statement of Compliance §2.907Certification This is an application for certification §2.911Application a)This is an application and has been filed electronically with form 731. b)All information required has been supplied. c)The applicant has signed the application (electronically). d)The technical data has been signed. (See Radiated Emissions) e)Applicant signature block on electronic form 731 completed by officer of the company or authorized company personnel. f) The appropriate fee has been paid electronically with VISA on 09-19- 2003. §2.915Grant This application demonstrates that all applicable technical standards have been met and a grant of this application will serve the public interest. §2.925Label Each piece of equipment for which authorization will be granted will be uniquely identified with “FCC ID: B4Z-785B-ALTP.” The required statement will appear with the FCC ID on the product and, although not required, in the installation instructions. See Exhibit A, PDF file id_label.pdf GE Interlogix, Inc. FCC_REPT.DOC 09/19/03 4:28 PM FCC ID: B4Z-785B-ALTP Page 5 of 25 §2.947Measurement Procedure a)The measurement procedure follows ANSI C63.4 procedure. Procedural notes are contained in the laboratory report. d)A list of test equipment used is contained in the laboratory report. §2.948Description of Measurement Facilities Measurements were performed at TUV Testing Services Open Test Site. The FCC keeps a full description of the measurement facilities on file. TUV’s acceptance and approval is dated as December 5, 1993 in a letter received from the FCC. The address of the test facility is: TUV Product Service 19035 Wild Mountain Road Taylors Falls, MN 55084-1758 Phone: 651-638-0297 Contact:Joel Schneider Test Engineer in Charge See Exhibit F, PDF file test_pho.pdf for sketch of measurement setup §2.1033Application for Certification a)Form 731 has been electronically filed on TBD. Items that did not apply were left blank. b)This technical report contains the following information where applicable. 1)Full name and mailing address of manufacturer and applicant for certification: GE Interlogix, Inc. 2266 North Second Street North Saint Paul, MN 55109 2)FCC Identifier: B4Z-785B-ALTP 3)Copy of installation instructions: See Exhibit G, PDF file: user_man.pdf GE Interlogix, Inc. FCC_REPT.DOC 09/19/03 4:28 PM FCC ID: B4Z-785B-ALTP Page 6 of 25 4)Brief Description of circuit functions and device operation: See Exhibit I, PDF file op_desc.pdf See Exhibit D, PDF file schemat.pdf for schematics (page 1) and parts placement (page 2) diagrams. 5) Block Diagram See Exhibit C, PDF file block.pdf. 6)Report of the measurements of radiation and conducted emissions: This document. 7)Photographs External: See Exhibit B, PDF file extern.pdf Internal: See Exhibit H, PDF file intern.pdf 8)Peripheral or Accessory devices: This is not applicable since this device is stand-a- lone product. 9) Transition Rules This application is not pursuant to the transition rules of §15.37 10)Emergency Broadcast decoding: This is not applicable to device in this application. 11)Application for direct sequence spread spectrum devices... This is not applicable to device in this application. 12)Application for scanning receivers... This is not applicable to device in this application. c)Composite Systems This is not applicable to device in this application. GE Interlogix, Inc. FCC_REPT.DOC 09/19/03 4:28 PM FCC ID: B4Z-785B-ALTP Page 7 of 25 3. Lab Measurements Discussion / Test Notes 3.1 Test Notes 3.1.1 Transmissions shall cease within 5 seconds of activation [ §15.231(a)(2) ] In the event of a panic alarm, eight packets are sent in the transmission. The packet duration is, at most, 30 ms, see Duty Cycle Correction Factor [§15.231(b)(2) and §15.35(c)]. The time between packets is random between 100 and 433ms, so the length of the longest transmission is: 8*30ms + 7*433ms = 3.271 seconds The following plot shows an eight packet transmission that concludes in less than 5 seconds. GE Interlogix, Inc. FCC_REPT.DOC 09/19/03 4:28 PM FCC ID: B4Z-785B-ALTP Page 8 of 25 See Fig1.pdf GE Interlogix, Inc. FCC_REPT.DOC 09/19/03 4:28 PM FCC ID: B4Z-785B-ALTP Page 9 of 25 3.1.2 …

Text truncated - open the document above for the full version.

Figure 1: Eight packet transmissions cease within 5 seconds

Figure 2: 1 Packet transmission in 100ms window

Figure 3: Expanded view of a single packet, duration is 23.5ms

Radiated Electromagnetic Emissions Test Report #: 3634 Run 01 Test Area:STS 3m Test Method:N/ATest Date:24-Apr-2001 EUT Model #:ALLEGRO CONTROL PANEL (52-785) EUT Power:60HZ/115VAC TRANSFORMER - 8VAC OUTPUT EUT Serial #:Temperature:5.2 °C Manufacturer:ITIRelative Humidity:84% EUT Description:SECURITY CONTROL PANELAir Pressure:99kPa Notes:HIGH POWER TRANSMIT MODEPage:1 of 4 FREQLEVELCABLE / ANT / PREAMPFINAL PEAK POL / HGT / AZFINAL AVERAGELIMIT (MHz)(dBuV)(dB) (dBm) (dB)(dBuV) (m) (DEG)(dBuV/m)FCC 15.231 Tested by: RMJ PrintedSignature Reviewed by: JTS PrintedSignature ALL READINGS MAXIMIZED. 100KHZ RBW BELOW 1GHZ AND 1MHZ RBW ABOVE 1GHZ. 319.45102.6 Pk3.9 / 14.0 / 28.292.2V / 1.0 / 0.072.275.8 319.4599.5 Pk3.9 / 14.0 / 28.289.1H / 1.0 / 0.069.175.8 212.9460.8 Pk3.1 / 10.9 / 28.046.8V / 1.0 / 0.026.855.8 106.4460.1 Pk2.2 / 9.2 / 27.843.7V / 1.0 / 0.023.755.8 425.9464.3 Pk4.6 / 17.0 / 28.057.9V / 1.0 / 0.037.955.8 532.4450.0 Pk5.2 / 18.3 / 28.145.4V / 1.0 / 0.025.455.8 638.9459.6 Pk5.7 / 19.5 / 28.156.8V / 1.0 / 0.036.855.8 745.4448.2 Pk6.3 / 21.4 / 28.048.0V / 1.0 / 0.028.055.8 851.9636.6 Pk6.7 / 22.4 / 27.638.1H / 1.0 / 0.018.155.8 958.4642.2 Pk7.1 / 23.4 / 27.545.2V / 1.0 / 0.025.255.8 1065.0239.1 Pk7.9 / 22.6 / 27.642.0V / 1.0 / 0.022.054.0 1171.5348.1 Pk8.2 / 23.7 / 27.552.5V / 1.0 / 0.032.554.0 1278.0348.8 Pk8.7 / 25.1 / 27.055.6V / 1.0 / 0.035.655.8 1384.5336.9 Pk9.3 / 26.0 / 29.442.7H / 1.0 / 0.022.754.0 1491.0346.9 Pk9.5 / 27.0 / 28.455.0V / 1.0 / 0.035.054.0 1597.5257.1 Pk10.3 / 26.5 / 28.065.9V / 1.0 / 0.045.954.0 1704.0239.0 Pk10.7 / 27.6 / 28.049.2H / 1.0 / 0.029.254.0 1810.5548.7 Pk10.7 / 27.8 / 28.059.2H / 1.0 / 0.039.255.8 1917.0751.6 Pk11.3 / 28.2 / 28.262.9V / 1.0 / 0.042.955.8 2023.5747.2 Pk11.3 / 29.6 / 27.560.7H / 1.0 / 0.040.755.8 2130.0750.6 Pk11.6 / 29.9 / 27.564.4H / 1.0 / 0.044.455.8 2236.5746.6 Pk11.8 / 30.1 / 27.860.6H / 1.0 / 0.040.654.0 Radiated Electromagnetic Emissions Test Report #: 3634 Run 01 Test Area:STS 3m Test Method:N/ATest Date:24-Apr-2001 EUT Model #:ALLEGRO CONTROL PANEL (52-785) EUT Power:60HZ/115VAC TRANSFORMER - 8VAC OUTPUT EUT Serial #:Temperature:5.2 °C Manufacturer:ITIRelative Humidity:84% EUT Description:SECURITY CONTROL PANELAir Pressure:99kPa Notes:HIGH POWER TRANSMIT MODEPage:2 of 4 FREQLEVELCABLE / ANT / PREAMPFINAL PEAK POL / HGT / AZFINAL AVERAGELIMIT (MHz)(dBuV)(dB) (dBm) (dB)(dBuV) (m) (DEG)(dBuV/m)FCC 15.231 Tested by: RMJ PrintedSignature Reviewed by: JTS PrintedSignature 2343.0742.0 Pk12.0 / 30.3 / 28.056.2H / 1.0 / 0.036.254.0 2449.5745.9 Pk12.4 / 30.5 / 27.960.8H / 1.0 / 0.040.855.8 2556.0741.3 Pk12.8 / 30.7 / 28.756.1H / 1.0 / 0.036.155.8 2662.5736.2 Pk13.0 / 30.8 / 28.451.6H / 1.0 / 0.031.654.0 2769.0742.9 Pk13.2 / 31.0 / 28.658.5H / 1.0 / 0.038.554.0 2875.5740.8 Pk13.6 / 31.1 / 28.656.9H / 1.0 / 0.036.954.0 2982.0735.9 Pk14.0 / 31.3 / 28.252.9H / 1.0 / 0.032.955.8 3088.5944.4 Pk14.5 / 31.5 / 28.262.2H / 1.0 / 0.042.255.8 3195.0936.6 Pk14.8 / 31.8 / 28.255.0H / 1.0 / 0.035.055.8 END OF SCAN. Radiated Electromagnetic Emissions Test Report #: 3634 Run 01 Test Area:STS 3m Test Method:N/ATest Date:24-Apr-2001 EUT Model #:ALLEGRO CONTROL PANEL (52-785) EUT Power:60HZ/115VAC TRANSFORMER - 8VAC OUTPUT EUT Serial #:Temperature:5.2 °C Manufacturer:ITIRelative Humidity:84% EUT Description:SECURITY CONTROL PANELAir Pressure:99kPa Notes:HIGH POWER TRANSMIT MODEPage:3 of 4 FREQLEVELCABLE / ANT / PREAMPFINAL PEAK POL / HGT / AZFINAL AVERAGELIMIT (MHz)(dBuV)(dB) (dBm) (dB)(dBuV) (m) (DEG)(dBuV/m)FCC 15.231 Tested by: RMJ PrintedSignature Reviewed by: JTS PrintedSignature ********** MEASUREMENT SUMMARY ********** 106.4460.1 Pk2.2 / 9.2 / 27.843.7V / 1.0 / 0.023.755.8 212.9460.8 Pk3.1 / 10.9 / 28.046.8V / 1.0 / 0.026.855.8 319.45102.6 Pk3.9 / 14.0 / 28.292.2V / 1.0 / 0.072.275.8 425.9464.3 Pk4.6 / 17.0 / 28.057.9V / 1.0 / 0.037.955.8 532.4450.0 Pk5.2 / 18.3 / 28.145.4V / 1.0 / 0.025.455.8 638.9459.6 Pk5.7 / 19.5 / 28.156.8V / 1.0 / 0.036.855.8 745.4448.2 Pk6.3 / 21.4 / 28.048.0V / 1.0 / 0.028.055.8 851.9636.6 Pk6.7 / 22.4 / 27.638.1H / 1.0 / 0.018.155.8 958.4642.2 Pk7.1 / 23.4 / 27.545.2V / 1.0 / 0.025.255.8 1065.0239.1 Pk7.9 / 22.6 / 27.642.0V / 1.0 / 0.022.054.0 1171.5348.1 Pk8.2 / 23.7 / 27.552.5V / 1.0 / 0.032.554.0 1278.0348.8 Pk8.7 / 25.1 / 27.055.6V / 1.0 / 0.035.655.8 1384.5336.9 Pk9.3 / 26.0 / 29.442.7H / 1.0 / 0.022.754.0 1491.0346.9 Pk9.5 / 27.0 / 28.455.0V / 1.0 / 0.035.054.0 1597.5257.1 Pk10.3 / 26.5 / 28.065.9V / 1.0 / 0.045.954.0 1704.0239.0 Pk10.7 / 27.6 / 28.049.2H / 1.0 / 0.029.254.0 1810.5548.7 Pk10.7 / 27.8 / 28.059.2H / 1.0 / 0.039.255.8 1917.0751.6 Pk11.3 / 28.2 / 28.262.9V / 1.0 / 0.042.955.8 2023.5747.2 Pk11.3 / 29.6 / 27.560.7H / 1.0 / 0.040.755.8 2130.0750.6 Pk11.6 / 29.9 / 27.564.4H / 1.0 / 0.044.455.8 2236.5746.6 Pk11.8 / 30.1 / 27.860.6H / 1.0 / 0.040.654.0 2343.0742.0 Pk12.0 / 30.3 / 28.056.2H / 1.0 / 0.036.254.0 Radiated Electromagnetic Emissions Test Report #: 3634 Run 01 Test Area:STS 3m Test Method:N/ATest Date:24-Apr-2001 EUT Model #:ALLEGRO CONTROL PANEL (52-785) EUT Power:60HZ/115VAC TRANSFORMER - 8VAC OUTPUT EUT Serial #:Temperature:5.2 °C Manufacturer:ITIRelative Humidity:84% EUT Description:SECURITY CONTROL PANELAir Pressure:99kPa Notes:HIGH POWER TRANSMIT MODEPage:4 of 4 FREQLEVELCABLE / ANT / PREAMPFINAL PEAK POL / HGT / AZFINAL AVERAGELIMIT (MHz)(dBuV)(dB) (dBm) (dB)(dBuV) (m) (DEG)(dBuV/m)FCC 15.231 Tested by: RMJ PrintedSignature Reviewed by: JTS PrintedSignature ********** MEASUREMENT SUMMARY ********** 2449.5745.9 Pk12.4 / 30.5 / 27.960.8H / 1.0 / 0.040.855.8 2556.0741.3 Pk12.8 / 30.7 / 28.756.1H / 1.0 / 0.036.155.8 2662.5736.2 Pk13.0 / 30.8 / 28.451.6H / 1.0 / 0.031.654.0 2769.0742.9 Pk13.2 / 31.0 / 28.658.5H / 1.0 / 0.038.554.0 2875.5740.8 Pk13.6 / 31.1 / 28.656.9H / 1.0 / 0.036.954.0 2982.0735.9 Pk14.0 / 31.3 / 28.252.9H / 1.0 / 0.032.955.8 3088.5944.4 Pk14.5 / 31.5 / 28.262.2H / 1.0 / 0.042.255.8 3195.0936.6 Pk14.8 / 31.8 / 28.255.0H / 1.0 / 0.035.055.8 Radiated Electromagnetic Emissions Tes…

Text truncated - open the document above for the full version.

Conducted Electromagnetic Emissions Test Report #: 5009 Run 2 Test Area: SCREEN ROOM Test Method: EN55022 Test Date: 03-Jul-2001 EUT Model #: 55-785 Allegro Control Panel EUT Power: 8 VAC via wall cube EUT Serial #: Temperature: 23 °C Manufacturer: ITI Relative Humidity: 50 % EUT Description: Air Pressure: 99 kPa Notes: Wall cube = 120 VAC / 60 Hz to 8 VAC PS Page: 1 of 2 FREQ LEVEL CABLE / LISN / ATTEN FINAL TEST POINT DELTA1 DELTA2 (MHz) (dBuV) (dB) (dBuV) EN55022 B QP EN55022 B Avg Tested by: G Jakubowski Printed Signature Reviewed by: TKS Printed Signature 0.170 -4.9 Qp 0.0 / 0.1 / -9.8 5.0 Neutral -60.0 N/A 0.170 -9.2 Av 0.0 / 0.1 / -9.8 0.7 Neutral N/A -54.3 0.215 -3.6 Qp 0.0 / 0.1 / -9.9 6.3 Neutral -56.7 N/A 0.215 -7.4 Av 0.0 / 0.1 / -9.9 2.5 Neutral N/A -50.5 0.300 -5.0 Qp 0.0 / 0.1 / -9.9 5.0 Neutral -55.2 N/A 0.300 -8.1 Av 0.0 / 0.1 / -9.9 1.9 Neutral N/A -48.3 0.345 -5.2 Qp 0.0 / 0.1 / -10.0 4.9 Neutral -54.2 N/A 0.345 -10.0 Av 0.0 / 0.1 / -10.0 0.1 Neutral N/A -49.0 0.510 -5.0 Qp 0.0 / 0.1 / -9.9 5.0 Neutral -51.0 N/A 0.510 -9.2 Av 0.0 / 0.1 / -9.9 0.8 Neutral N/A -45.2 4.07 -4.5 Qp 0.1 / 0.1 / -9.9 5.5 Neutral -50.5 N/A 4.07 -8.7 Av 0.1 / 0.1 / -9.9 1.3 Neutral N/A -44.7 0.170 -5.1 Qp 0.0 / 0.1 / -9.8 4.8 Line 1 -60.2 N/A 0.170 -9.2 Av 0.0 / 0.1 / -9.8 0.7 Line 1 N/A -54.3 0.215 -4.1 Qp 0.0 / 0.1 / -9.9 5.9 Line 1 -57.1 N/A 0.215 -7.8 Av 0.0 / 0.1 / -9.9 2.2 Line 1 N/A -50.8 0.300 -5.3 Qp 0.0 / 0.1 / -9.9 4.7 Line 1 -55.5 N/A 0.300 -9.2 Av 0.0 / 0.1 / -9.9 0.8 Line 1 N/A -49.4 0.345 -5.8 Qp 0.0 / 0.1 / -10.0 4.3 Line 1 -54.8 N/A 0.345 -9.8 Av 0.0 / 0.1 / -10.0 0.3 Line 1 N/A -48.8 0.510 -4.8 Qp 0.0 / 0.1 / -9.9 5.2 Line 1 -50.8 N/A 0.510 -8.5 Av 0.0 / 0.1 / -9.9 1.5 Line 1 N/A -44.5 4.07 -4.7 Qp 0.1 / 0.1 / -9.9 5.3 Line 1 -50.7 N/A 4.07 -9.3 Av 0.1 / 0.1 / -9.9 0.7 Line 1 N/A -45.3 Conducted Electromagnetic Emissions Test Report #: 5009 Run 2 Test Area: SCREEN ROOM Test Method: EN55022 Test Date: 03-Jul-2001 EUT Model #: 55-785 Allegro Control Panel EUT Power: 8 VAC via wall cube EUT Serial #: Temperature: 23 °C Manufacturer: ITI Relative Humidity: 50 % EUT Description: Air Pressure: 99 kPa Notes: Wall cube = 120 VAC / 60 Hz to 8 VAC PS Page: 2 of 2 FREQ LEVEL CABLE / LISN / ATTEN FINAL TEST POINT DELTA1 DELTA2 (MHz) (dBuV) (dB) (dBuV) EN55022 B QP EN55022 B Avg Tested by: G Jakubowski Printed Signature Reviewed by: TKS Printed Signature ********** MEASUREMENT SUMMARY ********** 0.510 -8.5 Av 0.0 / 0.1 / -9.9 1.5 Line 1 N/A -44.5 4.07 -8.7 Av 0.1 / 0.1 / -9.9 1.3 Neutral N/A -44.7 0.300 -8.1 Av 0.0 / 0.1 / -9.9 1.9 Neutral N/A -48.3 0.345 -9.8 Av 0.0 / 0.1 / -10.0 0.3 Line 1 N/A -48.8 0.215 -7.4 Av 0.0 / 0.1 / -9.9 2.5 Neutral N/A -50.5 4.07 -4.5 Qp 0.1 / 0.1 / -9.9 5.5 Neutral -50.5 N/A 0.170 -9.2 Av 0.0 / 0.1 / -9.8 0.7 Line 1 N/A -54.3

GE Interlogix, Inc 09/11/03 5:30 PM FCC ID: B4Z-785B-ALTP \\MSPFPS01\Dept\Engineer\eng_panel\proj\Allegro\Two-way touchpad\FCC\TEST_PHO.DOC 0.8 Meters EUT Receiving Antenna 3 Meters EXHIBIT F Test Setup Sketch for Radiated Emissions 1 Meter