BCE-WHB003BSJabra PRO 9x0 US-DECT Basestation

81-03148 E Jabra PRO ™ 920 www.jabra.com Quick Start Guide © 2011 GN Netcom A/S. All rights reserved. Jabra ® is a registered trademark of GN Netcom A/S. All other trademarks included herein are the property of their respective owners. (Design and specifications subject to change without notice). DESIGN REGISTRATION PENDING INTERNATIONAL REGISTER YOUR JABRA AT JABRA.COM/REGISTER – FOR NEWS, SUPPORT AND COMPETITIONS www.jabra.com MADE IN CHINAType: WHB003 ?  BS/HS EUROPE Belgique/Belgium + 49 (0)8031 2651 72Czech Republic + 420 800 522 722 Danmark Kontakt venligst din nærmeste forhandler (via følgende link) www.jabra.dk/forhandler Deutschland + 49 (0)8031 2651 72 Espzaña +34 916 398 064 France + 33 (0) 130 589 075 Italia +39 02 5832 8253 Luxembourg + 49 (0)8031 2651 72, Nederland + 49 (0)8031 2651 72 Norge + 47 32 22 74 70 Österreich + 49 (0)8031 2651 72 Poland 0-801-800-550; + 48 12 254-40-15 Russia [email protected] + 358 204 85 6040 Sverige + 46 (0)8 693 09 00 United Kingdom + 44 (0)1784 220 172 MIDDLE EAST/AFRICA E-mail Support: [email protected] USA & CANADACanada 1-800-489-4199USA 1-800-826-4656 WEB www.jabra.com (for the latest support information and online User Manuals). ASIAAustralia 1-800-636-086 (local distributor) China + 86-21-5836 5067 Hong Kong 800-968-265 (Toll free) India 000-800-852-1185 (Toll free) Indonesia 001-803-852-7664 Japan + 81-3-5297-7976 Malaysia 1800-812-160 (Toll free) New Zealand 0800-447-982 (Toll free) Philippines 1800-765-7022 (ETPI) 1800-1855-0144 (PLDT) Singapore 800-8523-794 -(Toll free) Taiwan 0080-186-3013 (Toll free) Thailand 001-8008523-794 (Toll free) For more languages please refer to the manuals on the CD.GN Netcom A/SLautrupbjerg 7DK-2750 BallerupDenmark CUSTOMER SUPPORT LANGUAGES ENGLISH / US 2 FRANÇAIS / FR 10 DEUTSCH / DE 18 ESPAÑOL / ES 26 ᜗᧯խ֮ / CHT 34 PACKAGE CONTENTS Optional accessories 3 2 US JABRA PRO 920 BASE 11 Mute indicator Audio link indicator Battery indicator Power adapter port Telephone port Handset portClear dial tone switch AUX port Microphone volume controls Foldable base stand JABRA PRO 920 HEADSET Speaker Noise-cancelling microphone Icon Event Battery charging (slow flash)Full batteryLow batteryVery low battery (fast flash)Unknown battery status Microphone muted Active audio link between headset and baseSearching for headset Speaker volume down Speaker volume up Mute Microphone boom arm Multi-function buttton LED indicator 5 4 US SETUP STEP 1: ATTACH THE HEADBAND 1. Align the headset and the headband wearing-style attachment, as illustrated, and press firmly together until they click into place (snap-to-click). 2. Rotate the microphone boom arm for left or right ear use.3. Adjust the length of the headband to fit snug against the head. CLICK OPTIONAL ACCESSORIES Attaching the earhook (not supplied in all regions)1. Assemble the earhook wearing-style attachment for left or right ear use. If necessary, remove the earbud and replace with another size for best fit. 2. Align the headset and the earhook wearing-style attachment, as illustrated, and press firmly together until they click into place (snap-to-click). 3. Shape the earhook to fit snug around the ear. CLICK STEP 2: UNFOLD THE BASE The Jabra PRO base stand can be folded into three positions: open, closed, and standing position. CLICK STEP 3: CONNECT TO POWER 1. Plug the supplied power adapter into the port marked on the base. 2. Connect the power adapter to the mains power socket. STEP 4: DOCK THE HEADSET Dock the headset. When docked correctly the headset battery will begin charging, if needed. Charge for 20 minutes or until the battery indicator on the base is steady green. Keep the headset docked during setup . CLICK 7 6 US STEP 5: SELECT AND CONNECT TO A DESK PHONE Select which desk phone you are connecting to from the following 4 options: OPTION 1 Desk Phone with Headset PortThis type of desk phone has a dedicated headset port (usually at the back of the phone). These phones typically have a button on the front panel for switching between handset and headset.1. Plug the supplied telephone cable into the port marked on the base. 2. Connect the telephone cable to the headset port on the desk phone. OPTION 2 Desk Phone with Jabra LinkA Jabra Link adapter enables an incoming call to be answered or ended by the headset multi-function button. Contact your local Jabra dealer to purchase a Jabra Link adapter for your specific desk phone.1. Connect the Jabra Link adapter as shown in adapter documentation supplied with the Jabra Link. On some phones the telephone cable will also need to be connected. 2. Call your connected desk phone using another phone to enable the Jabra Link adapter. Wait 10 seconds before answering the phone. Refer to Jabra Link documentation OPTION 3 Desk Phone with GN1000 remote Handset LifterThe GN1000 remote handset lifter manually lifts the desk phone handset to make or answer a call. For mounting instructions refer to documentation supplied with the GN1000.1. On the desk phone, unplug the handset cable from the phone body. 2. Connect the handset cable to the port marked on the base. 3. Plug the supplied telephone cable into the port marked on the base. 4. Connect the telephone cable into the handset port on the desk phone. 5. Connect the GN1000 cable into the port marked on the base. OPTION 4 Desk Phone without Headset PortThis desk phone does not have a dedicated headset port.1. On the desk phone, unplug the handset cable from the phone body. 2. Connect the handset cable to the port marked on the base. 3. Plug the supplied telephone cable into the port marked on the base. 4. Connect the telephone cable into the handset port on the desk phone. or or or or 9 8 US STEP 6: CONFIGURE THE SOUND 1 Put on the headset, or tap the headset multi-function button if the headset is currently undocked. 2 Get a dial tone by either pressing the headset button on the desk phone, or by lifting the desk phone handset. If there is no dial tone, ch…

Text truncated - open the document above for the full version.

1 81-03013 RevC Warranty, Warning and declaration - Wireless north america English Description of safety For your protection and comfort, GN Netcom, Inc. (“GN”) has implemented several protective measures in the headset which are carefully designed to maintain safe volume levels and ensure that the headset operates in compliance with government safety standards. This headset is suitable for indoor use only. !Warning! PeRmaNeNT heaRING loss may ResulT FRom loNG-TeRm exPosuRe To souNds aT hIGh volumes. use as low a volume as PossIble. headsets are capable of delivering sounds at loud volumes and high pitched tones. under certain circumstances, exposure to such sounds can result in permanent hearing loss or damage. The volume level may vary based on conditions such as the phone you are using, its reception and volume settings, and the environment. avoid prolonged use of the headset at excessive sound pressure levels. Please read the safety Guidelines below prior to using this headset. You can reduce the risk of hearing damage by following these safety guidelines: 1. Prior to using this headset follow these steps: - before putting on the headset, turn the volume control to its lowest level; - Put the headset on; and then - slowly adjust the volume control to a comfortable level. 2. During the use of this headset: - Keep the volume at the lowest level possible and avoid using the headset in noisy environments where you may be inclined to turn up the volume; - If increased volume is necessary, adjust the volume control slowly; - Ringing in the ears may indicate that the sound levels are too high; - If you experience discomfort or ringing in your ears, immediately discontinue using the headset and consult a physician; and - stop using the headset if it causes great discomfort. with continued use at a high volume, your ears may become accustomed to the sound level, which may result in permanent damage to your hearing without any noticeable discomfort. use caution while using your headset when you are engaging in any activ- ity that requires your full attention. while engaging in any such activity, removing the headset from your ear or turning off your headset will keep you from being distracted, so as to avoid accident or injury. safety information - Install in accordance with the instructions. do not install near any heat sources such as radiators, stoves, or other devices (including amplifiers) that produce heat. - unplug the headset stand during lightning, storms, or when the headset is not used for long periods of time. - use of a headset will impair your ability to hear other sounds. use caution while using your headset when you are engaging in any activity that requires your full attention. - The headset, the headset stand and the power adapter (the “products”) are not toys. Never allow children to play with the products and always store the products out of reach from children. - This package contains small parts that may be hazardous to children. The bags themselves, or the many small parts they contain, may cause choking if ingested. - Consult your physician before using the headset if you have a pacemaker or other electrical medical devices. - Never try to dismantle the products yourself, or push objects of any kind into the products, as this may cause short circuits which could result in a fire or electric shock. - None of the components can be replaced or repaired by users. only authorized dealers or service centers may open the products. If any parts of the products require replacement for any reason, including normal wear and tear or breakage, contact your local dealer. - avoid exposing the products to moisture, rain, or other liquids to protect against damage of the products or injury to you. - Keep the products, including cords and cables, away from operating machinery. - do not block any ventilation opening and protect the cables from being walked on or pinched, particularly at plugs and the point where they exit from the products. - observe all signs and instructions that require an electrical device or RF radio product to be switched off. - If the products overheat, if the products have been dropped or damaged, if the products have a damaged cord or plug, or if the products have been dropped in a liquid, immediately discontinue use and contact GN. - do not use in areas where there are explosive hazards. - dispose of the products according to local standards and regulations. Built-in battery care - The products are powered by a rechargeable battery. The full performance of a new battery is achieved only after two or three complete charge and discharge cycles. The battery can be charged and discharged hundreds of times, but will eventually wear out. - Recharge your battery only with the provided approved charger designated for the products. - If left unused, a fully charged battery will lose its charge over time. - leaving the products in hot or cold places will reduce the capacity and lifetime of the battery. - batteries may explode if damaged. Battery warning! - ”Caution” – The battery used in the products may present a risk of fire or chemical burn if mistreated. - do not attempt to open the products or replace the battery, unless otherwise stated in the manual. most batteries are built-in and not changeable. - use of other batteries may present a risk of fire or explosion and the warranty will be terminated. - dispose of batteries according to local regulations. Please recycle when possible. do not dispose as household waste or in a fire as the battery may explode. En 23 Charger care - do not attempt to charge the products with anything other than the aC adapter provided. The use of any other adapter may damage or destroy the products and will invalidate any approval or warranty. For availability on approved enhance- ments, please check with your dealer. - Charge the products according to the instructions supplied with the products. - some products cannot be used while chargi…

Text truncated - open the document above for the full version.

Test Report No.: G0M-1104-1092-C-2 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Annex A Photos EUT Front EUT Back Page 42 of 133

Print Instruction, Product Unit Label, NA 83-02961 B JJO 20.09.2011 1 : 1 A4 7.15 +/-0.2 20.5 +/-0.2 - All details on this label must be printed in black by use of a 600dpi Zebra printer. - Use blank 50x50mm grey-colored label. - Lower right corner, is used as reference for the position of the print. - CE-mark is used as reference to ensure the right dimension. CE-mark height must be 5mm +0.1/-0mm. - ”Basic Layout File, Product Unit Label” in tif-format must be used as graphical input for this label print. The layout in this le is made 4:1, in 600dpi resolution. - To ensure best possible label print quality 1. Use a printing program as BarTender or CODEsoft. 2. Insert image (the GN tif-le). 3. Scale the image until UL-circle mark height is 5.2mm +0.1/-0mm. 4. Place the image on the label area, with reference to the lower right corner (shown above). 5. Use a 600dpi Zebra printer. 6. Use the right and good quality resin based ink ribbon (i.e. RICOH B120HS). 7. Verify and adjust the thermal transfer heating on the printer to ensure best and solid print. www.jabra.com Designed and Engineered in Denmark Manufactured in China Add last-second data label,align www.jabra.com Model: WHB003BS Designed and Engineered in Denmark Manufactured in China FCC ID : BCE-WHB003BS IC : 2386C-WHB003BS Add last-second data label,align I.T.E. E210538 LBL ref: 83-02960-B

10.3 ±0.5 10 ±0.5 Product Foot Metal Weight Product Label

Test Report No.: G0M-1104-1092-C-2 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany PCB Front PCB Back Page 43 of 133

Eurofins Product Service GmbH Storkower Str. 38c, 15526 Reichenwalde, Phone +49-33631-888 0 Germany Fax +49-33631-888 660 EUROFINS PRODUCT SERVICE GMBH Testing Cert #1983.01 TEST - REPORT FCC RULES PART 15 / SUBPART B IC RSS-GEN ISSUE 3 DECT Basestation WHB003BS FCC ID: BCE-WHB003BS IC: 2386C-WHB003BS Test report no.: G0M-1104-1092-C-1 Test Report No.: G0M-1104-1092-C-1 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 2 of 40 TABLE OF CONTENTS 1 General Information 3 1.1 Notes 3 1.2 Operator: 5 1.3 Testing laboratory 6 1.3.1 Location 6 1.3.2 Details of accreditation status 6 1.3.3 Test location, where different 6 1.4 Details of applicant 7 1.5 Application details 7 1.6 Test item 7 1.6.1 Description of test item 7 1.6.2 Manufacturer (if different from applicant in point 1.4) 8 1.6.3 Frequency behavior 8 1.7 Test standards 8 2 Technical test 9 2.1 Summary of test results 9 2.2 Test environment 9 2.3 Test results 10 2.4 Test equipment utilized 11 2.4.1 Conducted Emission 12 2.4.2 Spurious Emission 13 2.5 Test protocols 14 3 Normative references 36 Annex A Photos 37 Test Report No.: G0M-1104-1092-C-1 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 3 of 40 1 General Information 1.1 Notes The purpose of conformity testing is to increase the probability of adherence to the essential requirements or conformity specifications, as appropriate. The tests were carried out and passed in accordance to the standards: FCC part 15B IC RSS-Gen Issue 3 The results of this test report relate exclusively to the item tested as specified in chapter “Description of test item” and are not transferable to any other test items. Eurofins Product Service GmbH is not responsible for any generalisations and conclusions drawn from this report. Any modification of the test item can lead to invalidity of test results and this test report may therefore be not applicable to the modified test item. The test report may only be reproduced or published in full. Reproducing or publishing extracts of the report requires the prior written approval of the Eurofins Product Service GmbH. This document is subject to the General Terms and Conditions and the Testing and Certification System of Eurofins Product Service GmbH, available on request or accessible at www.pt.eurofins.com . Test Report No.: G0M-1104-1092-C-1 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 4 of 40 Important Notes: Proper labeling is required for each device. Devices shall be labeled in accordance with labeling requirements pursuant to section 15.19 and section 2.1074 of the FCC rules. Devices subject to a Declaration of Conformity shall be uniquely identified by the responsible party. This identification shall not be of a format which could be confused with the FCC Identifier required on certified, notified type accepted or type approved equipment. The responsible party shall maintain adequate identification records to facilitate positive identification for each device. The user manual or instruction manual shall included also a warning statement that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Reference Section 15.21 Furthermore information to the user regarding to the interference potential of the device and about simple measures that can be taken to correct interference is required. Reference Section 15.105 The responsible party must warrant that each unit of equipment marketed under a Declaration of Conformity is identical to the unit tested and found acceptable with the standards and that the records maintained by the responsible party continue to reflect the equipment being produced under the Declaration of Conformity within the variation that can be expected due to quantity production and testing on a statistical basis. Test Report No.: G0M-1104-1092-C-1 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 6 of 40 1.3 Testing laboratory 1.3.1 Location EUROFINS PRODUCT SERVICE GMBH STORKOWER STR. 38c D- 15526 REICHENWALDE B. BERLIN GERMANY Telephone: + 49 33631 888-00 Telefax: + 49 33631 888-660 1.3.2 Details of accreditation status DAR ACCREDITED TESTING LABORATORY DAR-R EGISTRATION NUMBER: DAT-P-268/08 R ECOGNIZED NOTIFIED BODY EMC R EGISTRATION NUMBER: BNetzA-bS EMV-07/61 R ECOGNIZED NOTIFIED BODY R&TTE R EGISTRATION NUMBER: BNetzA-bS-02/51-53 FCC FILED TEST LABORATORY R EG.-NO. 96970 A2LA ACCREDITED TESTING LABORATORY C ERTIFICATE NO. 1983.01 B LUETOOTH QUALIFICATION TEST FACILITY (BQTF) A CCREDITED BY BLUETOOTH QUALIFICATION REVIEW BOARD I NDUSTRY CANADA FILED TEST LABORATORY R EG. NO. IC 3470A 1.3.3 Test location, where different Name : ./. Street : ./. Town : ./. Country : ./. Telephone : ./. Fax : ./. Test Report No.: G0M-1104-1092-C-1 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 7 of 40 1.4 Details of applicant Name : GN Netcom A/S Street : Lautrupbjerg 7 Town : DK-2750 Ballerup Country : Denmark Telephone : +45 4575 8888 Contact : Mr. Steen Kaiser E-mail : [email protected] 1.5 Application details Date of receipt of application : 18.04.2011 Date of receipt of test item : 18.04.2011 Date of test : 26.05.2011 – 30.05.2011 1.6 Test item 1.6.1 Description of test item Type of product : DECT Basestation Type identification : WHB003BS Serial number : without Hardware version : Alpha1 Software version : 0.17.0 Power supply : 7.5VDC 120VAC/DC Adapter Adapter type : Switching power supply Antenna type : internal antenna Photos : Please find in Annex. Additional information : none Test Report No.: G0M-1104-1092-C-1 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Page 8 of 40 1.6.2 Manufacturer (if different from applicant in point 1.4) Name : GN Netcom A/S Street : Lautrupbjerg 7 Town : DK-2750 Ballerup Country : Denmark 1.6.3 Frequency behavior…

Text truncated - open the document above for the full version.

Test Report No.: G0M-1104-1092-C-2 Eurofins Product Service GmbH Storkower Str. 38c, D-15526 Reichenwalde, Germany Test Setup radiated measurements Test Setup conducted measurements Page 44 of 133