BEJ-RSMV2RF Module

Attestation Letter (Section 2.911 (d)(5)(i)(ii) and 2.911(d)(7)) Date: 8/20/2024 FCC ID: BEJ-RSMV2 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046, USA We, LG Electronics Inc., as requested by FCC, are declaring that both requirements of Section 2.911 (d)(5)(i)(ii) and 2.911(d)(7) are being satisfied likes below to the FCC requirements to protect the nation`s networks and supply chains from equipment (“covered” equipment) according to FCC 22-84 and KDB 986446 D01. 1. Section 2.911 (d)(5)(i)(ii)) 2.911 (d)(5)(i) We certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. 2.911 (d)(5)(ii) And, we certifies that one of following, ☒ 1. We are not identified on the Covered List and are not an affiliate or subsidiary of an entity identified on the Covered List. ☐ 2. We are identified on the Covered List as an entity producing “covered” equipment. But, we can be authorized since the reason as explained below. ☐ 3. We are an affiliate or subsidiary of an entity identified on the Covered List. But, we can be authorized since the reason as explained below. *Only one of paragraphs 1, 2 or 3 should be checked, if checked on paragraphs 2 or 3, the reason why it does not include the “covered” equipment. 2. Section 2.911(d)(7) We, as required by section 2.911(d)(7), will also serve as the agent for service of process for the above referenced FCC ID. We will maintain the agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. And we have the responsibility to inform the FCC whenever the agent information changes. -. US Contact Name: David Kim -. US Address: LG Electronics USA, 111 Sylvan Avenue, North Building, Englewood Cliffs,New Jersey 07632, United States -. Email: [email protected] -. FRN: 0023476120 We are our own U.S agent for service of process. Sincerely yours, Name: David Kim Title: Team leader, LGEUS NA Policy & Regulatory Affairs Company Name: LG Electronics USA

Date: To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD To whom it may concern: Subject : FCC Agent Authorization Letter for FCC ID BEJ-RSMV2 This authorization is valid until further written notice from the applicant. Sincerely, Signed by: (Name) David Kim (Title) Team leader, LGEUS NA Policy & Regulatory Affairs [email protected] 201-470-2696 (Address) August 20, 2024 LG Electronics USA, 111 Sylvan Avenue, North Building, Englewood Cliffs, New Jersey 07632, United States We, the undersigned, hereby authorize HCT CO., LTD. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by HCT CO., LTD. on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). We recognize that we are still responsible for the terms and conditions outlined in the HCT America Client Services Agreement. _________________________ (Email Address) (Phone number) We declare that the information provided to the FCC is true and correct to thebest of our knowledge (47 CFR 2.911(d)) and we have been informed of thegrantee responsibilities (47 CFR 2.909) with regard to certified equipment

Date: Sept 10, 2024 FCC Modular Approval Attestation ☒ Single Modular Approval ☐ Single Limited Modular Approval (LMA) ☐ Split Modular Approval ☐ Split Limited Modular Approval (LMA) FCC ID: BEJ-RSMV2 FCC Part 15.212 Requirements: Please state details about how the following requirements could or could NOT be met; and state how control of the end product, into which the module will be installed, will be maintained by the applicant/manufacturer, such that full compliance of the end product is always ensured. ☒ 15.212 (a)(1)(i): The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. This module has the own shielding on transmitter using the ground layers as addressed in operational description. ☒ 15.212 (a)(1)(ii): The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with part 15 requirements under conditions of excessive data rates or over-modulation. This module has the buffered modulation/data inputs. ☒ 15.212 (a)(1)(ii): The modular transmitter must have its own power supply regulation. Yes. This module has the own power supply regulation circuitry. (U6 DC/DC TPS563240DDCR) ☒ 15.212 (a)(1)(iv): The modular transmitter must comply with the antenna and transmission system requirements of §§ 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of § 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. This module has PCB printed antennas as permanently attached on the module PCB. ☒ 15.212 (a)(1)(v): The modular transmitter must be tested in a stand- alone configuration. The test was performed in a stand-alone configuration without any host product. ☒ 15.212 (a)(1)(vi): The modular transmitter must be labeled with its own FCC ID number. This module is labeled with its own FCC ID on PCB as silk print. ☒ 15.212 (a)(1)(vii): The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instruction along with the module to explain any such requirements. This module complies with all specific rules and operating requirements. ☒ 15.212 (a)(1)(viii): The modular transmitter must comply with any applicable RF exposure requirements. This module complies with the RF Exposure requirements as mobile installation condition. (20 cm) If a module does NOT meet one or more of the above listed requirements, the applicant may request Limited Modular Approval (LMA). Name: David Kim Title: Team leader, LGEUS NA Policy & Regulatory Affairs Email Address: [email protected] Phone Number: 201-470-2696 Address: LG Electronics USA, 111 Sylvan Avenue, North Building, Englewood Cliffs,New Jersey 07632, United States

Date: To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD SUBJECT: Request for Confidentiality for FCC ID:BEJ-RSMV2 We hereby request confidential treatment of the information accompanying this application as outlined below: Exhibit 1 2 3 4 5 6 7 8 Sincerely, Signed by: (Name) David Kim (Title) Team leader, LGEUS NA Policy & Regulatory Affairs (Email Address) [email protected] (Phone number) 201-470-2696 (Address) LG Electronics USA, 111 Sylvan Avenue, North Building, Englewood Cliffs, New Jersey 07632, United States August 20, 2024 Description Block Diagram Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. LONG-TERM CONFIDENTIAL SHORT-TERM CONFIDENTIAL (180 DAYS) User’s Manual Test-Setup Photos Internal Photos External Photos Schematics Parts List LONG-TERM AND SHORT-TERM CONFIDENTIAL LIST

1.BRAND:LG 2.Product name:RFModule 3.Model name: RSMV2 4.KC:R-R-LGE-RSMV2 5.FCC ID: BEJ-RSMV2 ANATEL: HHHHH-AA-FFFFF IC: 2703N-RSMV2 <Front of the device> The label shown is representative of what will appear on the module when in production. This label may also contain other information. The label including certification information is printed on the module as shown below. LG Electronics Inc.

Subject: Justification Regarding AUT Report Date: 08-20-2024 FCC ID: BEJ-RSMV2 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA We, LG Electronics Inc., declared that an AUT report is not required for this device based on below. Only radiated measurements have been conducted to demonstrate compliance with FCC limits for this device. The EIRP limit under §15.255 (C)(2)(v), which applies to this device, does not include a conducted output power limit and this device is not subjected to §15.255(e). Therefore, AUT Report is not required for the evaluation of this device and has not been submitted in this application. If you have any question or comments, please contact the undersigned. Sincerely Yours, (Name) David Kim (Title) Team leader, LGEUS NA Policy & Regulatory Affairs (Email Address) [email protected] (Phone number) 201-470-2696 (Address) LG Electronics USA, 111 Sylvan Avenue, North Building, Englewood Cliffs, New Jersey 07632, United States

TEST REPORT FCC 60 GHz Test for RSMV2 Certification APPLICANT LG Electronics Inc. REPORT NO. HCT-RF-2408-FC007-R2 DATE OF ISSUE September 10, 2024 Tested by Ki Jae Kwon Technical Manager Jong Seok Lee Accredited by KOLAS, Republic of KOREA F-TP22-03(Rev.06) 1 / 28 The report shall not be (partly) reproduced except in full without approval of the laboratory. HCT CO., LTD. 2-6, 73, 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, Republic of Korea Tel. +82 31 645 6300 Fax. +82 31 645 6401 The report shall not be (partly) reproduced except in full without approval of the laboratory. F-TP22-03 (Rev. 06) Page 2 of 28 HCT CO.,LTD. 2-6, 73, 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, Republic of Korea Tel. +82 31 645 6300 Fax. +82 31 645 6401 TEST REPORT REPORT NO. HCT-RF-2408-FC007-R2 DATE OF ISSUE September 10, 2024 Applicant LG Electronics Inc. 84, Wanam-ro, Seongsan-gu, Changwon-si, Gyeongsangnam-do 51554, Republic of Korea Product Name Model Name RF Module RSMV2 FCC ID BEJ-RSMV2 Output Power 5.85 dBm Date of Test July 10, 2024 ~ September 05, 2024 Location of Test Ӎ Permanent Testing Lab ӎ On Site Testing (Address: 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, Republic of Korea) Test Standard Used Part 15.255 Test Results PASS The report shall not be (partly) reproduced except in full without approval of the laboratory. F-TP22-03 (Rev. 06) Page 3 of 28 Report No. HCT-RF-2408-FC007-R2 REVISION HISTORY The revision history for this test report is shown in table. Revision No. Date of Issue Description 0 August 09, 2024 Initial Release 1 September 05, 2024 -. Added test on AC Power line Conducted Emissions. -. Added equipment used in AC Power Line. 2 September 10, 2024 FCC ID modification Notice Content Engineering Statement: The measurements shown in this report were made in accordance with the procedures indicated, and the emissions from this equipment were found to be within the limits applicable. I assume full responsibility for the accuracy and completeness of these measurements, and for the qualifications of all persons taking them. It is further stated that upon the basis of the measurements made, the equipment tested is capable of operation in accordance with the requirements of the FCC Rules under normal use and maintenance. The results shown in this test report only apply to the sample(s), as received, provided by the applicant, unless otherwise stated. The test results have only been applied with the test methods required by the standard(s). The laboratory is not accredited for the test results marked *. Information provided by the applicant is marked **. Test results provided by external providers are marked ***. When confirmation of authenticity of this test report is required, please contact www.hct.co.kr This test report provides test result(s) under the scope accredited by the Korea Laboratory Accreditation Scheme (KOLAS), which signed the ILAC-MRA. (KOLAS (KS Q ISO/IEC 17025) Accreditation No. KT197) The report shall not be (partly) reproduced except in full without approval of the laboratory. F-TP22-03 (Rev. 06) Page 4 of 28 Report No. HCT-RF-2408-FC007-R2 CONTENTS 1. EUT DESCRIPTION 5 2. TEST METHODOLOGY 6 2.1 EUT CONFIGURATION 6 2.2 EUT EXERCISE 6 2.3 GENERAL TEST PROCEDURES 6 2.4 DESCRIPTION OF TEST MODES 6 3. INSTRUMENT CALIBRATION 7 4. FACILITIES AND ACCREDITATIONS 7 4.1 FACILITIES 7 4.2 EQUIPMENT 7 5. ANTENNA REQUIREMENTS 8 6. MEASUREMENT UNCERTAINTY 8 7. SUMMARY TEST OF RESULTS 9 8. TEST RESULT 10 8.1 OCCUPIED BANDWIDTH 10 8.2 RF OUTPUT POWER 12 8.3 SPURIOUS EMISSIONS 17 8.4 FREQUENCY STABILITY 23 8.5 AC Power line Conducted Emissions 25 9. LIST OF TEST EQUIPMENT 27 10. ANNEX A_TEST SETUP PHOTO 28 The report shall not be (partly) reproduced except in full without approval of the laboratory. F-TP22-03 (Rev. 06) Page 5 of 28 Report No. HCT-RF-2408-FC007-R2 1. EUT DESCRIPTION Model RSMV2 Additional Model - EUT Type RF module EUT Serial Number S01124300300-05 Power Supply 12.0 V Frequency Range 61.0 GHz ~ 61.5 GHz Modulation Type FMCW EIRP Peak 9.04 dBm Average 5.85 dBm Date(s) of Tests July 10, 2024 ~ September 05, 2024 The report shall not be (partly) reproduced except in full without approval of the laboratory. F-TP22-03 (Rev. 06) Page 6 of 28 Report No. HCT-RF-2408-FC007-R2 2. TEST METHODOLOGY The measurement procedure described in the ˑAmerican National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices˒ (ANSI C63.10-2020) Operating Under 47 CFR §15.255 were used in the measurement. 2.1 EUT CONFIGURATION The EUT configuration for testing is installed on EIRP measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application. 2.2 EUT EXERCISE The EUT was operated in the engineering mode to fix the Tx Frequency that was for the purpose of the measurements. 2.3 GENERAL TEST PROCEDURES Radiated Emissions The EUT is placed on a turn table, which is 0.8 m above the ground plane below 1 GHz and 1.5 m above 1 GHz with absorbers between the EUT and receiving antenna. The turntable shall rotate 360 degrees to determine the position of maximum emission level. EUT is set far-field distance away from the receiving antenna, which varied from 1 m to 4 m to find out the highest emission. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find out the max. emission, the relative positions of this hand-held transmitter (EUT) was rotated through three orthogonal axes according to the requirements in Section 8 of ANSI C63.10. (Version: 2020) 2.4 DESCRIPTION OF TEST MODES The EUT has been tested under operating condition. Test program used to control the EUT for staying in continuous transmitting and receiving mode is programmed. The report shall not be (partly) reproduced except in full without approval of the laboratory…

Text truncated - open the document above for the full version.

Subject: Justification Regarding AUT Report Date: 08-20-2024 FCC ID: BEJ-RSMV2 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA We, LG Electronics Inc., declared that an AUT report is not required for this device based on below. Only radiated measurements have been conducted to demonstrate compliance with FCC limits for this device. The EIRP limit under §15.255 (C)(2)(v), which applies to this device, does not include a conducted output power limit and this device is not subjected to §15.255(e). Therefore, AUT Report is not required for the evaluation of this device and has not been submitted in this application. If you have any question or comments, please contact the undersigned. Sincerely Yours, (Name) David Kim (Title) Team leader, LGEUS NA Policy & Regulatory Affairs (Email Address) [email protected] (Phone number) 201-470-2696 (Address) LG Electronics USA, 111 Sylvan Avenue, North Building, Englewood Cliffs, New Jersey 07632, United States