CHQ7264T3Transmitter

1/4 INSTRUCTIONS FOR OPERATION SETING THE OPERATING CONTROLS 1.This unit operates on AAA*2PCS.; 3 volts battery (not included). To prevent possible damage if the battery should leak, be sure to remove the battery when the unit is not use. 2. Store the controller away from excess heat or humidity. 3. This remote-control unit is required with 35bit code combinations. To prevent possible interference from or to other remote units such as garage door openers, car alarm or security system. 4.Operation buttons on the panel of transmitter. key – For FAN ON/OFF control . key –For Fan speed up control . key –For Fan slow down control . key – For FAN and LIGHT ON/OFF control . key – For LIGHT ON/OFF control . key – For Dimming - brightening key – For Dimming - dimming key – For Light color temperature Key - fan learning 2/4 GENERAL INFORMATION : This remote controller is designed to separately control your ceiling fan speed and light brightness. INSTRUCTIONS FOR INSTALLATION AND OPERATION OF FAN SPEED CONTROLLER Setup for ceiling fan controller 1. Turn off the power. (In order to make sure the electricity is entirely released, please press any button on the controller till no LED display showing) 2. Turn on the power 3. Press the FAN OFF button for more than 3 sec. The ceiling fan controller will have 2 blinks. It means the setup is successful. You could start to control the ceiling fan light and fan speed. NOTICE: The changes or modifications not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment. 3/4 IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/ TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause 4/4 Canada, Industry Canada (IC) Notices This device complies with Canada license‐exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Canada, Avis’s industry Canada (IC) Cet appareil est conforme avec Industrie Canada exemptes de licence RSS standard(s). Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement. Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under portable exposure conditions. Information concernant l'exposition aux fréquences radio (RF) La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite d'exposition aux fréquences radio d'Industry Canada (IC). Utilisez l’appareil de sans fil de façon à minimiser les contacts humains lors du fonctionnement normal. Ce périphérique a également été évalué et démontré conforme aux limites d'exposition aux RF d'IC dans des conditions d'exposition à des appareils portables.

NO. 29, AN HE ROAD,TAN-ZI SHIANG, TAICHUNG COUNTY, 427 Taiwan DATE : 2022/11/9 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification (FCC ID: CHQ7264T3; IC : 2968A-7264T3) Authority to Act as Agent On our behalf, I appoint Chenz Ker (MRT Technology (Taiwan) Co., Ltd./ No.38 Fuxing 2 nd Road, Guishan Dist., Taoyuan City, Taiwan 33377). to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with Rhine Electronics Co Ltd / NO. 29, AN HE ROAD,TAN-ZI SHIANG, TAICHUNG COUNTY, 427 Taiwan Dated this 2022/11/9 Agency agreement expiration date: 2022/12/7 By: Joseph Liao Signature Printed Title: General manager On behalf of : Rhine Electronics Co Ltd

NO. 29, AN HE ROAD,TAN-ZI SHIANG, TAICHUNG COUNTY, 427 Taiwan DATE : 2022/11/9 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: CHQ7264T3 Product Name: Transmitter Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: • Schematics • Block diagram • Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this 2022/11/9 By: Joseph Liao Signature Printed Title: General manager On behalf of : Rhine Electronics Co Ltd

NO. 29, AN HE ROAD,TAN-ZI SHIANG, TAICHUNG COUNTY, 427 Taiwan DATE : 2022/11/9 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: CHQ7264T3 Product Name: Transmitter Request for Short-Term Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission rules, and in accordance with the FCC Public notice dated June 15, 2004 (DA 04-1705), we hereby request short-term confidentiality for the following items prior to marketing the device.: ⚫ Test Setup Photos ⚫ External Photos ⚫ Internal Photos ⚫ User Manual These documents contain detailed system and equipment description and related information about the product which （Rhine Electronics Co Ltd） considers to be proprietary, confidential, and a custom design and, otherwise would not release to the general public. Since this design is a basis from which future technological products will evolve, （Rhine Electronics Co Ltd） considers this information to be of benefit to its competitors, and that the disclosure of information in these documents would give competitors an unfair advantage in the market. This request is being made retroactively due to an over site on our part. We understand that the information has been publicly available 180 days after date of grant. Dated this 2022/11/9 By: Joseph Liao Signature Printed Title: General manager On behalf of : Rhine Electronics Co Ltd Telephone: 886 4-2531-2825

Declaration letter Dear Sir, For our business issue and marketing requirement, we would like to list different model number on the FCC, IC certificates and reports, as following: FCC ID: CHQ7264T3 IC: 2968A-7264T3 Model No.: UC7264T3, UC7264T3A Model Difference: The difference of models is that UC7264T3A has no COLOR TEMP button, the other hardware was the same. Model Difference UC7264T3 With COLOR TEMP button UC7264T3A No COLOR TEMP. button Thank you! --------------------------------------------------- Signature: Joseph Liao Date: 2022/11/24

Report No.: 2210TW5405-U1 Product: Transmitter Brand Name: RHINE Model Number: UC7264T3/ UC7264T3A 1 of 6 External Photograph (1) EUT Photo (UC7264T3) (2) EUT Photo (UC7264T3) Report No.: 2210TW5405-U1 2 of 6 (3) EUT Photo (UC7264T3) (4) EUT Photo (UC7264T3) Report No.: 2210TW5405-U1 3 of 6 (5) EUT Photo (UC7264T3) (6) EUT Photo (UC7264T3) Report No.: 2210TW5405-U1 4 of 6 (7) EUT Photo (UC7264T3A) (8) EUT Photo (UC7264T3A) Report No.: 2210TW5405-U1 5 of 6 (9) EUT Photo (UC7264T3A) (10) EUT Photo (UC7264T3A) Report No.: 2210TW5405-U1 6 of 6 (11) EUT Photo (UC7264T3A) (12) EUT Photo (UC7264T3A)

Label & Label location Model:UC7264T3 FCC ID:CHQ7264T3 IC: 2968A-7264T3 This device complies with part 15 of the FCC rules . Operation is subject to the following two conditions . (1)This device may not cause harmful interference and (2)This device must accept any interference received ,Including interference that may cause undesired operation . Model:UC7264T3A FCC ID:CHQ7264T3 IC: 2968A-7264T3 This device complies with part 15 of the FCC rules . Operation is subject to the following two conditions . (1)This device may not cause harmful interference and (2)This device must accept any interference received ,Including interference that may cause undesired operation .

Report No.: 2210TW5405-U1 Product: Transmitter Brand Name: RHINE Model Number: UC7264T3/ UC7264T3A 1 of 4 Internal Photograph (1) EUT Photo (UC7264T3) (2) EUT Photo (UC7264T3) Report No.: 2210TW5405-U1 2 of 4 (3) EUT Photo (UC7264T3) (4) EUT Photo (UC7264T3) Report No.: 2210TW5405-U1 3 of 4 (5) EUT Photo (UC7264T3A) (6) EUT Photo (UC7264T3A) Report No.: 2210TW5405-U1 4 of 4 (7) EUT Photo (UC7264T3A) (8) EUT Photo (UC7264T3A)

MRT Technology (Taiwan) Co., Ltd Report No.: 2210TW5405-U1 Phone: +886-3-3288388 Report Version: 1.0 Fax: +886-3-3288918 Issue Date: 2022-11-22 Web: www.mrt-cert.com FCC ID: CHQ7264T3 Page Number: 1 of 30 IC: 2968A-7264T3 FCC ID : CHQ7264T3 IC : 2968A-7264T3 APPLICANT : RHINE ELECTRONIC CO., LTD. Application Type : Certification Product : Transmitter Model No. : UC7264T3 Series Model No. : UC7264T3A Brand Name : RHINE FCC Classification : FCC Part 15 Security/Remote Control Transmitter (DSC) FCC Rule Part(s) : Part 15.231(b) ISED Standard : RSS 210 Issue 10 Test Procedure(s) : ANSI C63.10-2013 Received Date : October 31, 2022 Test Date : November 01 ~ 11, 2022 MEASUREMENT REPORT Tested By : ( Fran Chen ) Reviewed By : ( Paddy Chen ) Approved By : ( Chenz Ker) The test results only relate to the tested sample. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.10-2013. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Taiwan) Co., Ltd. Report No.: 2210TW5405-U1 FCC ID: CHQ7264T3 Page Number: 2 of 30 IC: 2968A-7264T3 Revision History Report No. Version Description Issue Date Note 2210TW5405-U1 1.0 Original Report 2022-11-22 Report No.: 2210TW5405-U1 FCC ID: CHQ7264T3 Page Number: 3 of 30 IC: 2968A-7264T3 CONTENTS Description Page 1. INTRODUCTION ..................................................................................................................... 6 1.1. Scope ........................................................................................................................... 6 1.2. MRT Test Location ....................................................................................................... 6 2. PRODUCT INFORMATION ..................................................................................................... 7 2.1. Equipment Description .................................................................................................. 7 2.2. Test Standards ............................................................................................................. 7 2.3. Test Methodology ......................................................................................................... 7 2.4. EUT Setup and Test Mode ........................................................................................... 8 3. ANTENNA REQUIREMENTS .................................................................................................. 9 4. TEST EQUIPMENT CALIBRATION DATE ............................................................................ 10 5. MEASUREMENT UNCERTAINTY .......................................................................................... 11 6. TEST RESULT ...................................................................................................................... 12 6.1. Summary .................................................................................................................... 12 6.2. Radiated Emissions .................................................................................................... 13 6.2.1. Standard Applicable ................................................................................................ 13 6.2.2. Test Procedure........................................................................................................ 13 6.2.3. Test Setup ............................................................................................................... 14 6.2.4. Test Results ............................................................................................................ 15 6.3. 20dB Bandwidth / 99% Bandwidth .............................................................................. 21 6.3.1. Standard Applicable ................................................................................................ 21 6.3.2. Test Procedure........................................................................................................ 21 6.3.3. Test Setup ............................................................................................................... 21 6.3.4. Test Result .............................................................................................................. 22 6.4. Transmission Time ...................................................................................................... 23 6.4.1. Standard Applicable ................................................................................................ 23 6.4.2. Test Procedure........................................................................................................ 23 6.4.3. Test Setup ............................................................................................................... 23 6.4.4. Test Result .............................................................................................................. 24 6.5. Duty Cycle .................................................................................................................. 25 6.5.1. Standard Applicable ................................................................................................ 25 6.5.2. Test Procedure........................................................................................................ 25 6.5.3. Test Setup ............................................................................................................... 25 6.5.4. Test Result .............................................................................................................. 26 6.6. AC Conducted Emissions Measurement ..................................................................... 28 Report No.: 2210TW5405-U1 FCC ID: CHQ7264T3 Page Number: 4 of 30 IC: 2968A-7264T3 6.…

Text truncated - open the document above for the full version.

Report No.: 2210TW5405-U1 Product: Transmitter Brand Name: RHINE Model Number: UC7264T3/ UC7264T3A 1 of 1 Test Photograph Test Mode: Mode 1 Description: Radiated Emission Test Setup for below 1GHz Test Mode: Mode 1 Description: Radiated Emission Test Setup for above 1GHz