CWTB230XSensor for opening and closing doors in cars

Since this device is always used with vehicle, it is not sold to general end users separately. Therefore there is no user manual of this device by alone. The following statements must be described on the user manual of the vehicle; ALPS ALPINE Confidential This device complies with part 15 of FCC Rules and Innovation, Science and Economic Development Canadaʼs licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme à la partie 15 des règles de la FCC et aux normes des CNR dʼInnovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) L'appareil ne doit pas produire de brouillage, et (2) L'appareil doit accepter tout brouillage subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the userʼs authority to operate the equipment. This device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure conditionwithout restriction.Cet appareil a été évalué pour répondre aux exigences générales d'exposition aux RF. L'appareil peut être utilisé dans des conditions d'exposition portable sans restriction. Cet équipement est conforme aux limites dʼexposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices d'exposition et dʼexposition aux fréquences radioélectriques (RF) CNR- 102 de lʼ ISDE puisque cet appareil a une niveau tres bas d'energie RF. This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the ISED radio frequency (RF) Exposure rules as this equipment has very low levels of RF energy. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. FCC ID: CWTB230X IC: 1788F-B230X

050523-17 rev 8 Certification Application Attestation Statements Date: October 27, 2023 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern: Statement for 47 CFR section 2.911(d)(5)(i) ALPS ALPINE CO.; LTD. certifies that as of the date of the application the equipment for which authorization is sought is not “covered” equipment 1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not “covered” equipment. Additional Explanation: <N/A> Statement for 47 CFR section 2.911(d)(5)(ii) ALPS ALPINE CO., LTD. (“the applicant”) certifies that, as of the date of the filing of this application, the applicant ☐ - is / ■ - is not identified on the Covered List as an entity producing “covered” equipment. Thank you, By: __________________________ _____Yuji Ouchi_________ (Signature 2 ) (Print name) Title: ____Group Leader___________ Company: __ALPS ALPINE CO., LTD.__ Telephone: __+81-229-23-5111_________ 1 ‐ The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist . 2 - Letters must be placed on appropriate letterhead.

LPSALPINE ALPS ALPINE NORTH AMERICA, INC. 1500 Atlantic Blvd Auburn Hills, Ml 48326 TO: American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 ATTENTION: FCC Certification - Section 2.911(d)(7) Information Designated U.S. Agent Company Name: Alps Alpine North America Inc. Contact Name: Prudencio Cabigao Street Address: 1500 Atlantic Blvd Auburn Hills, City/Province/Zip: Ml 48326 Telephone No: (248) 830-5302 Email: [email protected] FRN #: 002367 467 4 This letter is to confirm that we ("the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911 (d)� behalf of the Applicant noted below. U.S. Agent Signature: J - � � Date: 27 October 2023 Signed by (Printed Name/Title): Prudencio Cabigao / Engineering Manager The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission­ related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: ALPS ALPINE CO., LTD. Grantee Code: CWT Contact Name: Yuji Ouchi Street Address: 6-3-36 Furukawanakazato, City/Province/Zip: Osaki City/ Miyagi-pref. / 989-6181 Telephone No: +81 (229)23-5111 Email: [email protected] Applicant Signature 1: Date: October 27, 2023 Signed by (Printed Name/Title): Yuji Ouchi/ Group Leader 1- Letters must be placed on appropriate letterhead. The signee for the applicant must be one of the following: Applicant (grantee) contact of record in the FCC's authorization system, or authorized officers or employee of the applicant (grantee).

050222-17 (Signature 1 ) (Print name) Title: _____Group Leader_________ On behalf of: __ALPS ALPINE CO., LTD.__ (Company Name) Telephone: __+81-229-23-5111___________ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: _____12 months_____ By: __________________________ ____Yuji Ouchi__________ Authority to Act as Agent Date: October 27, 2023 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern: Takehiko SHIOTA is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant

050222-31a Request for Confidentiality Date: December 25, 2023 Subject: Confidentiality Request for: ______CWTB230X and 1788F-B230X______ Pursuant to FCC 47 CFR 0.457(d) and 0.459 and/or IC RSP-100, Section 12.4, the applicant requests that a part of the subject application(s) be held confidential. Type of Confidentiality Requested Exhibit ☐ Short Term ☒ Permanent Block Diagrams ☐ Short Term --------------------------- External Photos ☒ Short Term ☐ Permanent * 1 Internal Photos ☐ Short Term ☒ Permanent Operation Description/Theory of Operation ☐ Short Term ☒ Permanent Parts List & Placement/BOM ☐ Short Term ☒ Permanent Tune-Up Procedure ☐ Short Term ☒ Permanent Schematics ☐ Short Term --------------------------- Test Setup Photos ☐ Short Term ☐ Permanent * 1 User’s Manual ALPS ALPINE CO,. LTD. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality for FCC Applications: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Short Term Confidentiality for Industry Canada Applications: Starting May 2022, ISED will recognize short term confidentiality on certain exhibits until the intended date of marketing. The applicant requests the exhibits selected above as short term confidential be withheld from public view until: May 27, 2024 . Sincerely, By: Yuji Ouchi _ (Signature/Title 2 ) (Print name) 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at: https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has

DSP Research,Inc. 1-4-3 Minatojima Minamimachi Chuo-ku Kobe City Hyogo 650-0047 Japan TEL:+81-78-940-0377 Fax:+81-78-940-037 050222-17 Authority to Act as Agent Date: December 11, 2023 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern: Kimberly Colbert is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: _____12 months_____ By: ___________ __Takehiko SHIOTA______ (Signature 1 ) (Print name) Title: _Executive Director__________ On behalf of: _DSP Research, Inc.__________ (Company Name) Telephone: _+81-78-940-0138_____________ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Product Photo(External)B2301 ①②③④⑤⑥ Bottom view① 1 Top view② ③ ⑥ ⑤ ④

Label layout image IC:1788F-B230X FCC ID：CWTB230X FCC ID：CWTB230X IC:1788F-B230X

Product Photo(Internal) B2302 Bottom viewTop view 1 Comment 1) 1）Regarding Internal photos, please add an additional close-up photograph of the TX antenna area as well as label the internal photos with an arrow and note as appropriate to denote the actual location. Antenna Remove the case 60 GHz

FCC PART §15.255 AND ISED CANADA RSS-210 CERTIFICATION TEST REPORT for the KICK SENSOR (B2301/B2302) FCC ID: CWTB230X ISED ID: 1788F-B230X WLL REPORT# 18420-01 REV 3 Prepared for: ALPS ALPINE CO., LTD. 6-3-36 Furukawaoakazato Osaki City, Miyagi-pier, 989-6181 (Japan) Prepared By: Washington Laboratories, Ltd. 4840 Winchester Boulevard., Suite #5 Frederick, Maryland 21703 (USA) Testing Certificate AT-1448 Certificates and reports shall not be reproduced except in full, without the written permission of Washington Laboratories, LTD. ALPS ALPINE CO., LTD. Kick Sensor (B2301/B2302) FCC §15.255 Certification Test Report WLL Report 18420-01 Rev 3 Page 2 of 66 FCC §15.255 and ISED Canada RSS-210 Certification Test Report for the ALPS ALPINE CO., LTD. Kick Sensor (B2301/B2302) FCC ID: CWTB230X IC ID: 1788F-B230X December 18, 2023 WLL Report# 18420-01 Rev 3 Prepared by: ___________________________ Ryan Mascaro RF Test Engineer Reviewed by: ____________________________ Steven D. Koster President ALPS ALPINE CO., LTD. Kick Sensor (B2301/B2302) FCC §15.255 Certification Test Report WLL Report 18420-01 Rev 3 Page 3 of 66 Abstract This report has been prepared on behalf of ALPS ALPINE CO., LTD. to support the attached Application for Equipment Authorization. This test report and application filings are being submitted for a Field Disturbance Sensor Transmitter under Part §15.255 of the FCC Rules and Regulations and under Spectrum Management and Telecommunications Policy RSS-210, Issue 10 (12/2019) of Innovation, Science and Economic Development Canada (ISED). This certification test report documents the test configuration and testing results for the ALPS ALPINE CO., LTD. Kick Sensor (B2301/B2302). The information provided in this report is only applicable to the device herein documented, as the EUT. Radiated testing up to 40 GHz was performed in the Free-space Anechoic Chamber Test-site (FACT) 3m Chamber of Washington Laboratories, LTD., located at 4840 Winchester Boulevard, Suite #5., Frederick, Maryland, 21703 (USA). Site description and site attenuation data have been placed on file with the FCC's Sampling and Measurements Branch at the FCC Laboratory in Columbia, Maryland. Washington Laboratories, LTD., has been accepted by the FCC and approved by ANAB under Testing Certificate AT-1448 as an independent FCC test laboratory. The Washington Laboratories, Ltd. ISED Canada number is 3035A. The ALPS ALPINE CO., LTD. Kick Sensor (B2301/B2302) complies with the limits and requirements for a Field Disturbance Sensor Transmitter under Part §15.255 of the FCC Rules and Regulations, and under Innovation, Science and Economic Development Canada (ISED) RSS-210, Annex J, Issue 10 (12/2019). Revision History Description of Change Release Date Rev 0 Initial Release December 18, 2023 Rev 1 ACB Comments, Dated: 12/20/2023 December 23, 2023 Rev 2 ACB Comments, Dated: 12/29/2023 January 4, 2024 Rev 3 Integration of Applicant Test Data, Annex A January 11, 2024 ALPS ALPINE CO., LTD. Kick Sensor (B2301/B2302) FCC §15.255 Certification Test Report WLL Report 18420-01 Rev 3 Page 4 of 66 Table of Contents 1 Introduction ..................................................................................................................................... 7 1.1 Compliance Statement ................................................................................................................ 7 1.2 Test Methods ............................................................................................................................... 7 1.3 Test Dates.................................................................................................................................... 7 1.4 Test Scope ................................................................................................................................... 7 1.5 Contract Information ................................................................................................................... 9 1.6 Test and Support Personnel ........................................................................................................ 9 1.7 Test Location .............................................................................................................................. 9 1.8 EUT Digital Emissions ............................................................................................................... 9 2 Test Results ................................................................................................................................... 10 2.1 Transmitter Occupied Bandwidth ............................................................................................. 10 2.2 Radiated Power (EIRP), via Wideband RF Detector ................................................................ 12 2.3 Radiated Power (EIRP), via Field Strength .............................................................................. 15 2.4 Peak Transmitter Conducted Output Power ............................................................................. 17 2.5 Radiated Spurious Emissions, Below 40 GHz .......................................................................... 18 2.6 Radiated Spurious Emissions, 40 GHz to 200 GHz ................................................................. 25 2.7 Transmitter Frequency Stability ............................................................................................... 33 2.8 Transmitter Duty Cycle and Timing Scheme ........................................................................... 38 3 Equipment Under Test .................................................................................................................. 48 3.1 EUT Identification & Description ............................................................................................ 48 3.2 Testing Algorithm ..................................................................................................................…

Text truncated - open the document above for the full version.

Test Setup Photographs EUT Model: Kick-Sensor, B2301/B2302 FCC ID: CWTB230X WLL Project: 18420 IC ID: 1788F-B230X