DD4GLXD2Wireless microphone transmitter

GLXD User Guide Shure Incorporated Confidential DRAFT 7.6.12 DRAFT 7.6.12 IMPORTANT SAFETY INSTRUCTIONS 1. READ these instructions. 2. KEEP these instructions. 3. HEED all warnings. 4. FOLLOW all instructions. 5. DO NOT use this apparatus near water. 6. CLEAN ONLY with dry cloth. 7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventila- tion and install in accordance with the manufacturer’s instructions. 8. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not place any open flame sources on the product. 9. DO NOT defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replace- ment of the obsolete outlet. 10. PROTECT the power cord from being walked on or pinched, particularly at plugs, conve- nience receptacles, and the point where they exit from the apparatus. 11. ONLY USE attachments/accessories specified by the manufacturer. 12. USE only with a cart, stand, tripod, bracket, or table specified by the manu- facturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. UNPLUG this apparatus during lightning storms or when unused for long periods of time. 14. REFER all servicing to qualified service personnel. Servicing is required when the ap- paratus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the apparatus. 16. The MAINS plug or an appliance coupler shall remain readily operable. 17. The airborne noise of the Apparatus does not exceed 70dB (A). 18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connection. 19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 20. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure. 21. Operate this product within its specified operating temperature range. This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and mainte- nance instructions in the literature accompanying this unit. DRAFT 7.6.12 4 GLXD Wireless Audio System The GLXD is a versatile wireless audio system offering quality sound and easy setup. Back channel control between the transmitter and receiver enables real-time parameter changes. Compact size maximizes freedom of movement. ① Connect power supply to the receiver.② Plug the power supply into an AC power source. ③ Turn on the receiver. ④ Install charged batteries into the transmitter. ⑤ Turn on transmitter to create a link with the receiver. ⑥ The system is now ready to use. Test the audio and adjust the gain if necessary. Receiver Quick Start DRAFT 7.6.12 5 GLXD4 Receiver Rear Panel Receiver Screen 1 23 45 67 89 1 1 2 98 34 6 5 7 ① Group Displays the selected group. ② Channel Displays the selected channel. ③ Transmitter Battery Runtime Displays remaining battery life in hours and minutes. ④ Audio Meter Indicates audio signal level ⑤ Gain Displays transmitter gain setting in 1 dB increments. ⑥ Top Indicator Indicates audio signal peak. ⑦ Lock Displayed when a linked transmitter controls are locked, flashes when the controls of a locked receiver are pressed. ⑧ OL Indicator Indicates audio overload. ⑨ Scanning Indicates a scan is in process. Front Panel 1011 12 13 14 ① Antenna Carries the wireless signal, 2 per receiver. ② RF LED • Blue = RF link OK • Flashing = Linking in progress • Off = No RF link or transmitter off ③ Group Button • Momentary press to start Group Scan • Press and hold 2 seconds for manual group edit ④ Link Button • Press for 2 seconds to activate linking • Press momentarily for remote ID ⑤ Channel • Momentary press to start Channel Scan • Press and hold 2 seconds for manual Channel edit ⑥ LCD Screen Displays receiver and transmitter status ⑦ Gain Buttons Press to increase or decrease receiver gain in 1 dB increments ⑧ Battery Indicator Illuminates when battery is in charging bay: • Red = battery charging • Green Flashing = • Green = battery charged ⑩ Battery Charging Bay Charges transmitter battery while receiver is powered. ⑪ Power Switch Powers the unit on and off. ⑫ Power Supply Jack Connect the supplied 15 V DC external power supply. ⑬ Mic Out XLR Microphone Output Jack Supplies microphone-level audio output. ⑭ USB Port ⑮ Instr Out Balanced ¼" (6.35mm) TRS Audio Output Powers the unit on and off. DRAFT 7.6.12 6 Transmitters Locking and Unlocking the controls The controls of the transmitter and receiver can be locked to prevent accidental or unauthorized changes to settings. ① Antenna Carries wireless signal. ② Power LED • Green = transmitter on • Green Flashing = tranmitter power switch locked • Red = remaining transmitter runtime less than 1 hour • Flashing Red = replace transmitter batteries • Flashing Green/Red = link identification • Off = transmitter off ③ Power Switch Turns the transmitter on/off. ④ Battery Compartment Holds 1 Shure rechargeable battery. ⑤ USB Charging Door Connection point for USB battery charging options. ⑥ Link Button • Press for 2 seconds to activate linking • Press momentarily for remote ID ⑦ TA4M Input Jack Connects to a 4-Pin Mini Connector (TA4F) microphone or instrument cable. ⑧ Microphone Cartridge Models …

Text truncated - open the document above for the full version.

September 27, 2012 Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, Illinois 60515-1082 SUBJECT: REQUEST FOR NON-DISCLOSURE FOR FCC ID: DD4GLXD2 To Whom It May Concern: Pursuant to 47 CFR Section 0.459, Shure Incorporated hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application for FCC ID # DD4GLXD2: a. Schematic Diagrams b. Operational Description c. Block Diagram Above materials contain trade secrets, proprietary and technical information which would customarily be guarded from competitors under 47 CFR section 0.457(d)(2). Disclosure or publication of any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. Shure Incorporated understands that pursuant to 47 CFR section 0.457(d)(1)(ii) disclosure of the applicant and all accompanying documentation will not be made before the date of the grant. Sincerely yours, Craig Kozokar EMC Project Engineer, Global Compliance Shure Incorporated

45.0mm Wireless Transmitter Model GLXD2 Z2 2.4000-2.4835 GHz R XX-XXXX XXX MADE IN CHINA FCC ID:DD4GLXD2 IC:616A-GLXD2 Z540 N108 신고번호 KCC-CRM-SHU-GLXD2Z2 OFTA CERT #: XXXXXXXX CMIIT ID: XXXXXXXXXX CCXXxxYYyyZzW 29.0mm = oon LINK TX + LINK TX = ID I I I I I I I I I I I I I I I I I I I I I :02 link RX LINK TX + = Link SHURE INCORPORATED, NILES, IL. 60714 CAMERA READYARTWORK PLATE #: CR-3402 REVISON#: 01 DESCRIPTION: Nameplate Artwork MODEL #: GLXD2 PROJECT #:17690 SCALE: 1:1 DESIGNER: J Laskey APPROVED:

For Shure Incorporated 5800 West Touhy Niles, IL 60714 P.O. Number 4500221175 Date Received June 13, 2012 Date Tested June 13, 2012 through August 14, 2012 Test Personnel Mark Longinotti and Ian Carnegie Specification FCC "Code of Federal Regulations" Title 47, Part 15, Subpart C, Sections 15.207 and 15.247 for Digital Modulation Intentional Radiators Operating within the band 2400-2483.5MHz FCC “Code of Federal Regulations” Title 47, Part15, Subpart 15B, Section 15.107 and 15.109 for Receivers and Digital Devices Industry Canada RSS-210 Industry Canada RSS-GEN Industry Canada ICES-003 Test Report By: Mark Longinotti EMC Engineer Approved By: Raymond J. Klouda Registered Professional Engineer of Illinois - 44894 Engineering Test Report No. 1201084-03 Measurement of RF Interference from a GLXD2 Handheld Transceiver Elite Electronic Engineering Inc. 1516 Centre Circle Downers Grove, IL 60515 Tel : (630) 495-9770 Fax: (630) 495-9785 www.elitetest.com Engineering Test Report No. 1201084-03 THIS REPORT SHALL NOT BE REPRODUCED, EXCEPT IN FULL, WITHOUT THE WRITTEN APPROVAL OF ELITE ELECTRONIC ENGINEERING INCORPORATED. Page 2 of 91 TABLE OF CONTENTS PARAGRAPH DESCRIPTION OF CONTENTS PAGE NO. 1 INTRODUCTION ............................................................................................................................................... 5 1.1 Scope of Tests .......................................................................................................................................... 5 1.2 Purpose ..................................................................................................................................................... 5 1.3 Deviations, Additions and Exclusions ....................................................................................................... 5 1.4 EMC Laboratory Identification .................................................................................................................. 5 1.5 Laboratory Conditions ............................................................................................................................... 5 2 APPLICABLE DOCUMENTS ............................................................................................................................ 6 3 EUT SET-UP AND OPERATION ...................................................................................................................... 6 3.1 General Description .................................................................................................................................. 6 3.1.1 Power Input .......................................................................................................................................... 6 3.1.2 Peripheral Equipment ........................................................................................................................... 6 3.1.3 Interconnect Cables ............................................................................................................................. 6 3.1.4 Grounding ............................................................................................................................................. 6 3.2 Operational Mode ..................................................................................................................................... 6 3.3 EUT Modifications ..................................................................................................................................... 7 4 TEST FACILITY AND TEST INSTRUMENTATION .......................................................................................... 7 4.1 Shielded Enclosure ................................................................................................................................... 7 4.2 Test Instrumentation ................................................................................................................................. 7 4.3 Calibration Traceability ............................................................................................................................. 7 4.4 Measurement Uncertainty ......................................................................................................................... 7 5 TEST PROCEDURES ....................................................................................................................................... 8 5.1 Digital Device (Digital Apparatus) ............................................................................................................. 8 5.1.1 Powerline Conducted Emissions .......................................................................................................... 8 5.1.1.1 Requirements .............................................................................................................................. 8 5.1.1.2 Procedures .................................................................................................................................. 8 5.1.1.3 Results ......................................................................................................................................... 9 5.1.2 Radiated Measurements ...................................................................................................................... 9 5.1.2.1 Requirements .............................................................................................................................. 9 5.1.2.2 Procedures .................................................................................................................................. 9 5.1.2.3 Results ....................................................................................................................................... 10 5.2 Receiver .................................................................................................................................................. 11 5.2.1 Requirements .......…

Text truncated - open the document above for the full version.

Engineering Test Report No. 1201084-03 Page 21 of 91 Figure 3 Test Setup for Conducted Emissions Engineering Test Report No. 1201084-03 Page 22 of 91 Figure 4 Test Setup for Radiated Emissions – 30MHz to 2GHz, Horizontal Polarization Test Setup for Radiated Emissions – 30MHz to 2GHz, Vertical Polarization Engineering Test Report No. 1201084-03 Page 23 of 91 Figure 5 Test Setup for Radiated Emissions – 2GHz to 18GHz, Horizontal Polarization Test Setup for Radiated Emissions – 2GHz to 18GHz, Vertical Polarization Engineering Test Report No. 1201084-03 Page 24 of 91 Figure 6 Test Setup for Radiated Emissions – 18GHz to 25GHz, Horizontal Polarization Test Setup for Radiated Emissions – 18GHz to 25GHz, Vertical Polarization