E5M-INET900MDS iNet 900

MDS 05-2873A01, REV. FCC AUGUST 2001 Wireless IP/Ethernet Transceiver MDS iNet 900 ™ DRAFT 6—8/30/01 Below are the basic steps for installing the MDS iNet 900 transceiver. Detailed instructions are given in the Section 3.0, INSTALLATION PLANNING , on page 5 of this manual. 1. Install and connect the antenna system to the radio • Use good quality, low-loss coaxial cable. Keep the feedline as short as possible. • Preset directional antennas in the direction of desired transmission/reception. 2. Apply DC power to the radio (13.8 Vdc @ 500 mA) • Connect a DC power source to the i Net’s power connector.(Negative ground only.) • Observe proper polarity when connecting the DC cable. See Figure 10 on page 16. 3. Review the initial configuration profile • Connect a computer with HTTP browser to the LAN port, or a terminal to the COM1 port, to identify, and revise if necessary the MDS i Net 900’s primary operating parameters. (See “Step 5—Review the Radio’s Configuration” on page 16 for details.)  Operating Mode: Access Point (Master) or Station Adaptor (Remote)  Internet Protocol (IP) Address  Network Name  Time and Date—If event logging is enabled 1 Z? 4. Verify proper operation of the MDS i Net radio-modem • See Table 2 on page 7 for an explanation of the LED status indicators. • Refine the antenna heading for maximum received signal strength using the radio signal strength indicator ( RSSI ) function found on the browser’s home page. The RSSI display will be in dBm. 5. Connect the user’s equipment to the MDS i Net’s LAN, COM1or COM2 ports • LAN—Use a RJ-45 Ethernet connector/cable. • COM2—Recommended for serial-based data equipment. Use a DB-9 female connector. Interface is RS-232/EIA-232 compatible. • COM1—Reserve, if practical, for use to connect terminal for unit configuration. Use a DB-9 male connector. Interface is RS-232/EIA-232 compatible. (See Table 9 on page 34 for pin descriptions and Figure 9 on page 16 for port defaults.) 6. Verify proper operation of the user’s equipment • A properly configured system will work exactly as it would if the data equipment were communicating through a conventional wired system. (See Table 4.6 on page 18) • The LINK LED will blink intermittently under normal operation if it connects with another MDS iNet 900 transceiver. • Use the IP “PING” command to verify the Access Point can be contacted by the Station Adapter. 1. While this may be of value, the time and date setting does not seem like a primary parameter and is beyond the scope of this draft. QUICK START GUIDE DRAFT 6—8/30/01 MDS 05-2873A01, Rev. AMDS i Net 900 Installation and Operation Guidei DRAFT 6—8/29/01 TABLE OF CONTENTS 1.0 ABOUT THIS MANUAL................................................................ 1 2.0 PRODUCT DESCRIPTION ......................................................... 1 2.1 Transceiver Features ........................................................................ 2 2.2 Spread Spectrum Radios— How Are They Different? .......................................................................... 3 2.3 Typical Applications .......................................................................... 3 Wireless IP/Ethernet LAN Connectivity .......................................... 3 Point-to-Point System ..................................................................... 3 Dealing with difficult terrain............................................................. 4 2.4 Accessories ...................................................................................... 4 3.0 INSTALLATION PLANNING......................................................... 5 3.1 General Requirements ..................................................................... 5 3.2 Site Selection ................................................................................... 6 Terrain and Signal Strength ............................................................ 6 Conducting a Site Survey ............................................................... 7 3.3 A Word About Radio Interference .................................................... 8 3.4 Antenna & Feedline Selection .......................................................... 9 Antennas ........................................................................................ 9 Feedlines ...................................................................................... 11 3.5 How Much Output Power Can be Used? ....................................... 11 Calculating System Gain .............................................................. 12 4.0 INSTALLATION .......................................................................... 13 4.1 Step 1— Mounting the Transceiver ................................................ 13 4.2 Step 2—Install the Antenna and Feedline ...................................... 15 4.3 Step 3—Connect the Data Equipment ........................................... 15 4.4 Step 4—Measure & Install Primary Power ..................................... 16 4.5 Step 5—Review the Radio’s Configuration .................................... 16 Procedure ..................................................................................... 17 4.6 Step 6—Connect the User Data Equipment .................................. 18 4.7 Step 7—Check for Normal Operation ............................................ 18 Procedure ..................................................................................... 18 4.8 Performance Optimization .............................................................. 19 Antenna Aiming ............................................................................ 19 Antenna SWR Check (Z? Major revision needed?) ...................... 20 5.0 TRADITIONAL REPEATER CONFIGURATION WITH TWO RADIOS 20 5.1 Overview ........................................................................................ 20 iiMDS i Net 900 Installation GuideMDS 05-2873A01, Rev. A DRAFT 6—8/29/01 5.2 Antennas ..........................…

Text truncated - open the document above for the full version.

Installation Guide Review Draft 3—12/17/01 Wireless IP/Ethernet Transceiver MDS 05-2873A01, REV. D3 DECEMBER 2001 MDS i NET 900 ™ MDS 05-2873A01, Rev. D3Installation Guide1 Review Draft 3—12/17/01 CONTENTS ABOUT THIS MANUAL............................................................ 4 PRODUCT DESCRIPTION...................................................... 4 INSTALLATION PLANNING..................................................... 5 INSTALLATION ........................................................................ 6 Step 1—Mount the Transceiver ....................................................6 Step 2—Install the Antenna .........................................................7 Step 3—Measure & Install Primary Power...................................7 Step 4—Review the Radio’s Configuration ..................................8 Step 5—Connect the Data Equipment.........................................9 Step 6—Check for Normal Operation ........................................10 Performance Optimization..........................................................10 TROUBLESHOOTING ........................................................... 11 iNET SPECIFICATIONS ........................................................ 13 IN CASE OF DIFFICULTY... .................................................. 14 INSTALLATION REFERENCE CHART ............. (Center Insert) Copyright Notice This publication is protected by U.S. copyright law. Copyright 2001, Micro- wave Data Systems, Inc. All rights reserved. Serviceability of this Manual While every reasonable effort has been made to ensure the accuracy of this manual, product improvements may result in minor differences between the manual and the product shipped to you. If you have additional questions or need an exact specification for a product, please contact our Customer Service Team using the information at the back of this guide. Microwave Data Systems Incorporated reserves its right to correct any errors and omissions. Updated information may also be available on our Web site at www.microwavedata.com. 2Installation Guide MDS 05-2873A01, Rev. D3 Review Draft 3—12/17/01 Operational Safety Notices The radio equipment described in this guide emits radio frequency energy. Although the power level is low, the concentrated energy from a directional antenna may pose a health hazard. Do not allow people to come closer than two meters (6 feet) to the antenna when the transmitter is operating. This manual is intended to guide a professional installer in installing, oper- ating and performing basic system maintenance on the described equipment. FM/UL/CSA Notice MDS i Net 900 When Approved This product is available for use in Class I, Division 2, Groups A, B, C & D Hazardous Locations. Such locations are defined in Article 500 of the National Fire Protection Association (NFPA) publication NFPA 70, otherwise known as the National Elec- trical Code. The transceiver has been recognized for use in these hazardous locations by three independent agencies —Underwriters Laboratories (UL), Factory Mutual Research Corporation (FMRC) and the Canadian Standards Association (CSA). The UL certi- fication for the transceiver is as a Recognized Component for use in these hazardous locations, in accordance with UL Standard 1604. The FMRC Approval is in accor- dance with FMRC Standard 3611. The CSA Certification is in accordance with CSA STD C22.2 No. 213-M1987. FM/UL/CSA Conditions of Approval MDS i Net 900 When Approved The transceiver is not acceptable as a stand-alone unit for use in the hazardous loca- tions described above. It must either be mounted within another piece of equipment which is certified for hazardous locations, or installed within guidelines, or conditions of approval, as set forth by the approving agencies. These conditions of approval are as follows: 1. The transceiver must be mounted within a separate enclosure which is suitable for the intended application. 2. The antenna feedline, DC power cable and interface cable must be routed through conduit in accordance with the National Electrical Code. 3. Installation, operation and maintenance of the transceiver should be in accor- dance with the transceiver's installation manual, and the National Electrical Code. 4. Tampering or replacement with non-factory components may adversely affect the safe use of the transceiver in hazardous locations, and may void the approval. RF Exposure MDS 05-2873A01, Rev. D3Installation Guide3 Review Draft 3—12/17/01 Do not disconnect equipment unless power has been switched off or the area is know to be non-hazardous. Refer to Articles 500 through 502 of the National Electrical Code (NFPA 70) for further information on hazardous locations and approved Division 2 wiring methods. 1 Z? FCC Notice, U.S.A. MDS i Net 900 When Approved The MDS iNet 900 transceivers comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful inter- ference, and (2) this device must accept any interference received, including interfer- ence that may cause undesired operation. This device is specifically designed to be used under Section 15.247 of the FCC Rules and Regulations. Any unauthorized modification or changes to this device without the express approval of Microwave Data Systems may void the user’s authority to operate this device. Furthermore, this device is indented to be used only when installed in accordance with the instructions outlined in this manual. Failure to comply with these instructions may also void the user’s authority to operate this device. FCC Information This equipment has been tested and found to comply with the limits for a Class A dig- ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio fre- quency energy…

Text truncated - open the document above for the full version.

C:\windows\TEMP\probonholdemail.doc TIMCO TIMCOTIMCO TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 email: tei@t imcoengr.com (date) FCC SUBJECT: MICROWAVE DATA SYSTEMS, INC. FCC ID: E5M-INET900 MODEL: To Whom It may Concern, This EUT was tested in a stand alone condition. In reviewing this application we have discovered the following problem/s; Sincerely, Sid Sanders

175 Science Parkway, Rochester, New York 14620 USA (585) 242-9600 Phone (585) 242-9620 Fax January 18, 2002 FEDERAL COMMUNICATIONS COMMISSION 7435 Oakland Mills Road Columbia, MD 21046 U.S.A. Subject: Request for withholding from public disclosure the schematic diagrams and system block diagrams pursuant to an application for certification. Applicant: Microwave Data Systems Inc. Product: INET Model: INET900 FCC ID: E5M-INET900 Dear Sir/Madam, We, Microwave Data Systems, would like to request that the schematic diagrams, system block diagram, Theory of Operation and Bill of Materials submitted with the application for certification be withheld from public disclosure as per Section 0.459 of FCC Rules. This request is made under the provisions of Section 0.457(d) of the Commission's Rules, and Section 552(b)(4) of the Freedom of Information Act. These sections authorize as a withholding from public inspection materials which would be privileged as a matter of law if retained by the person submitting them, and materials which would not customarily be released to the public by that person. If you have any queries, please do not hesitate to contact us at 716 242-9600: Yours truly, Dennis McCarthy Agency Compliance Engineer Microwave Data Systems 175 Science Parkway Rochester NY 14620 Phone (585) 242-8440 Email [email protected]

March 11, 2002 Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: TCB Approval E5M-INET900 Applicant: Microwave Data Systems, Incorporated Correspondence Reference Number: 3626 731 Confirmation Number: TC363980 Date of Original Email: 03/01/2002 To Whom It May Concern: Thank you for your email of the 1 st of March 2002. We are pleased to respond to the questions raised in your email. For the sake of completeness, we have reproduced the issues raised along with our responses. FCC Issue 1: The Test Report data shows a channel spacing of 333 kHz and channel separation of 317 kHz. The bandwidth is greater than the channel spacing, which is not compliant with the provisions of Section 15.247(a)(1) of the Rules. Explain this non-compliance. MDS Response 1: The MDS INET, as indicated in the application and test report, operates in two modes 2-level or 4-level. Test data has been provided, where required under Part 15.247, for both modes of operation. The actual data channel separation for the MDS iNET900 radio is 316.5kHz. The 20 dB occupied bandwidth for the 4-level is less than the channel spacing and the INET in that configuration complies with all the requirements under section 15.247. The test data provided for the 2-level 20 db occupied bandwidth would lead one to believe that the MDS INET900 is non compliant in that mode. The attached re-run plot of the 20 dB occupied bandwidth for the 2-level mode of the original MDS INET900 test unit clearly shows that the MDS INET900 is also compliant in the 2-level mode. The only explanation we can offer for the original non-compliance is that conceivably during the process of setting the MDS INET900 in the 2-level mode a mis-configuration in the deviation register must have occurred. End users do not have the ability to adjust these registers. To ensure that there are no such issues with any other measurements all measurements specific to the 2 –level mode and occupied bandwidth (20 dB bandwidth, Band-edge Compliance) were re-run with random data. Full compliance was further revalidated. These plots are also attached. Figures... Figure 1 (20 dB Bandwidth: 256 kbps/2-level @ 902.5 MHz) Figure 2 (20 dB Bandwidth: 256 kbps/2-level @ 915.16 MHz) Figure 3 (20 dB Bandwidth: 256 kbps/2-level @ 927.504 MHz) Figure 4 (Low Band Edge Compliance with fixed carrier: 256 kbps/2-level) Figure 5 (Low Band Edge Compliance with hopping: 256 kbps/2-level) Figure 6 (High Band Edge Compliance with fixed carrier: 256 kbps/2-level) Figure 7 (High Band Edge Compliance with hopping: 256 kbps/2-level) FCC Issue 2: The Test report states that there are 80 hopping channels. However there is no data or spectral plots to support this. Upload spectrum plots showing compliance with the number of hopping channels. MDS Response 2: Enclosed are spectral plots showing the MDS iNET900 hopping on 80 channels. Figure 8 (Number of Hopping Frequencies: 902-915 MHz) Figure 9 (Number of Hopping Frequencies: 915-928 MHz) FCC Issue 3: The band frequencies are listed in the Grant. The Grant should have the lowest and highest fundamental frequency that the device transmits. Correct the Grant. MDS Response 3: MDS supports the FCC recommendation to have the highest and lowest fundamental frequencies listed on the Grant. Those frequencies are 902.5 MHz and 927.5035 MHz. FCC Issue 4: The Grant condition states that this is a Limited Modular Approval for use in the manufacturers products only. Please remove from the Grant conditions any reference to module or limited modular approach. Typically the only mention of modules is "Modular Approval" when all conditions of A00-1407 have been met. FCC Issue 5: This is a fixed device. You treated it like a mobile device. Correct the Grant condition to indicate that this is a fixed device and RF exposure requirements are determined at the time of licensing. MDS Response 4 and 5: The observations noted in FCC requests 4 and 5 have been fully addressed by redrafting the grant notes as below. We further believe that this draft not only addresses the concerns expressed under 4 and 5 but also is in accordance with FCC Public Notice DA 00-1407 of June 26th 2000 and previous grants by the bureau. Antennas used for this transmitter must be professionally installed on fixed mounted outdoor structures. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This transmitter can only be used in enclosures designed by Microwave Data Systems, Inc. such that compliance of the end product is assured. Finally, we hope that our responses are to the FCC’s satisfaction. We would expect the FCC’s kind consideration for an immediate restoration of our grant. Sincerely, Dennis McCarthy Agency Compliance Engineer Microwave Data Systems 175 Science Parkway Rochester NY 14620 Phone (585) 242-8440 Email: [email protected]

REVISED EXTERNAL PHOTOS OF EUT Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 1 REVISED EXTERNAL PHOTOS OF EUT Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 2 REVISED EXTERNAL PHOTOS OF EUT Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 3

FCC ID Label Location of Label on Device

ANNEX 4 – INTERNAL PHOTOS OF EUT Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A4 - 1 ANNEX 4 – INTERNAL PHOTOS OF EUT Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A4 - 2 ANNEX 4 – INTERNAL PHOTOS OF EUT Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A4 - 3

INET Model No.: INET900 FCC ID: E5M-INET900 Applicant: Microwave Data Systems Inc. 175 Science Parkway Rochester, NY USA, 14620 In Accordance With FEDERAL COMMUNICATIONS COMMISSION (FCC) PART 15, SUBPART C, SECTION 15.247 Frequency Hopping Spread Spectrum Transmitters Operating in the Frequency band 902 - 928 MHz UltraTech's File No.: MIC46-FTX This Test report is Issued under the Authority of Tri M. Luu, Professional Engineer, Vice President of Engineering UltraTech Group of Labs Date: January 24, 2002 Report Prepared by: Dan Huynh Tested by: Mr. Hung Trinh, EMI/RFI Technician Issued Date: January 24, 2002 Test Dates: December 16 - 19, 2001 The results in this Test Report apply only to the sample(s) tested, and the sample tested is randomly selected. UltraTech 3000 Bristol Circle, Oakville, Ontario, Canada, L6H 6G4 Telephone (905) 829-1570 Facsimile (905) 829-8050 Website: www.ultrat4ech-labs.com Email: [email protected] FCC Part 15, Subpart C, Section 15.247 - Frequency Hopping Spread Spectrum Transmitters Contents i INET, Model INET900 FCC ID: E5M-INET900 ULTRATECH GROUP OF LABS File #: MIC46-FTX 3000 Bristol Circle, Oakville, Ontario, Canada L6H 6G4 January 24, 2002 Tel. #: 905-829-1570, Fax. #: 905-829-8050, Email: [email protected] , Website: http://www.ultratech-labs.com • Assessed by ITI (UK) Competent Body, NVLAP (USA) Accreditation Body & ACA/AUSTEL (Australia), VCCI (Japan) • Accredited by Industry Canada (Canada) under ACC-LAB (Europe/Canada MRA and APEC/Canada MRA) • Recognized/Listed by FCC (USA) • All test results contained in this engineering test report are traceable to National Institute of Standards and Technology (NIST) TABLE OF CONTENTS EXHIBIT 1. SUBMITTAL CHECK LIST................................................................................................................... 1 EXHIBIT 2. INTRODUCTION .................................................................................................................................... 2 2.1. SCOPE.................................................................................................................................................................... 2 2.2. RELATED SUBMITTAL ( S )/ GRANT ( S ) .......................................................................................................................... 2 2.3. NORMATIVE REFERENCES .............................................................................................................................. 3 EXHIBIT 3. PERFORMANCE ASSESSMENT .........................................................................................................4 3.1. CLIENT INFORMATION ........................................................................................................................................ 4 3.2. E QUIPMENT UNDER T EST (EUT) INFORMATION................................................................................................. 4 3.3. EUT’S TECHNICAL SPECIFICATIONS............................................................................................................. 5 3.4. L IST OF EUT’ S P ORTS ............................................................................................................................................. 5 3.5. A NCILLARY EQUIPMENT .......................................................................................................................................... 6 EXHIBIT 4. EUT OPERATING CONDITIONS AND CONFIGURATIONS DURING TESTS .......................... 7 4.1. C LIMATE TEST CONDITIONS ..................................................................................................................................... 7 4.2. O PERATIONAL TEST CONDITIONS & ARRANGEMENT FOR TEST S .............................................................................. 7 EXHIBIT 5. SUMMARY OF TEST RESULTS .......................................................................................................... 8 5.1. LOCATION OF TESTS ......................................................................................................................................... 8 5.2. APPLICABILITY & S UMMARY OF EMC E MISSION T EST R ESULTS ...................................................................... 8 5.3. MODIFICATIONS INCORPORATED IN THE EUT FOR COMPLIANCE PURPOSES ............................................................... 8 EXHIBIT 6. MEASUREMENTS, EXAMINATIONS & TEST DATA FOR EMC EMISSIONS.......................... 9 6.1. T EST P ROCEDURES .................................................................................................................................................. 9 6.2. MEASUREMENT UNCERTAINTIES .............................................................................................................................. 9 6.3. MEASUREMENT EQUIPMENT USED ............................................................................................................................ 9 6.4. ESSENTIAL/PRIMARY FUNCTIONS AS DECLARED BY THE MANUACTURER ..................................... 9 6.5. UNLICENSED MODULAR TRANSMITETR APPROVAL REQUIREMENTS @ FCC P UBLIC N OTICE DA 00-1407 (JU NE 26, 2000).................................................................................................................................................... 10 6.6. COMPLI A NCE WITH FCC PART 15 – GENERAL TECHNICAL REQUIREMENTS ................................... 13 6.7. H OPPING C HANNEL C ARRIER F REQUENCY C HARACTERISTICS [47 CFR §§ 15.247( A )(1) & ( A )(1)( I )] ................. 17 6.7.1. Limits ............................................................................................................................................................ 17 6.7.2. Method of Measurements.............................................................................................................................. 17 6.7.3. Test Arrangement ..........................................…

Text truncated - open the document above for the full version.

ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 1 Plot # 1 20 dB Occupied Bandwidth ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 2 Plot # 2 20 dB Occupied Bandwidth ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 3 Plot # 3 20 dB Occupied Bandwidth ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 4 Plot # 4 20 dB Occupied Bandwidth ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 5 Plot # 5 20 dB Occupied Bandwidth ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 6 Plot # 6 20 dB Occupied Bandwidth ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 7 Plot # 7 Channel Hopping Frequency Separation ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 8 Plot # 8 Average Time of Occupancy Low End of Frequency Band ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 9 Plot # 9 Average Time of Occupancy Low End of Frequency Band ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 10 Plot # 10 Average Time of Occupancy Middle of Frequency Band ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 11 Plot # 11 Average Time of Occupancy Middle of Frequency Band ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 12 Plot # 12 Average Time of Occupancy High End of Frequency Band ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 13 Plot # 13 Average Time of Occupancy High End of Frequency Band ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 14 Plot # 14 Band-Edge Spurious Emissions at Antenna Terminals Low End of Frequency Band Single Frequency Mode ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 15 Plot # 15 Band-Edge Spurious Emissions at Antenna Terminals Low End of Frequency Band Pseudorandom Channel Hopping Mode ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 16 Plot # 16 Band-Edge Spurious Emissions at Antenna Terminals Low End of Frequency Band Single Frequency Mode ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 17 Plot # 17 Band-Edge Spurious Emissions at Antenna Terminals Low End of Frequency Band Pseudorandom Channel Hopping Mode ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 18 Plot # 18 Band-Edge Spurious Emissions at Antenna Terminals High End of Frequency Band Single Frequency Mode ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 19 Plot # 19 Band-Edge Spurious Emissions at Antenna Terminals High End of Frequency Band Pseudorandom Channel Hopping Mode ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 20 Plot # 20 Band-Edge Spurious Emissions at Antenna Terminals High End of Frequency Band Single Frequency Mode ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 21 Plot # 21 Band-Edge Spurious Emissions at Antenna Terminals High End of Frequency Band Pseudorandom Channel Hopping Mode

ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 22 Plot # 22 Spurious Emissions at Antenna Terminals ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 23 Plot # 23 Spurious Emissions at Antenna Terminals ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 24 Plot # 24 Spurious Emissions at Antenna Terminals ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 25 Plot # 25 Spurious Emissions at Antenna Terminals ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 26 Plot # 26 Spurious Emissions at Antenna Terminals ANNEX 1 - TEST DATA PLOTS Microwave Data Systems Inc. INET, Model INET900 FCC ID: E5M-INET900 A1 - 27 Plot # 27 Spurious Em…

Text truncated - open the document above for the full version.