E8HKT-1332Bluetooth Keyboard

KT-1332 Bluetooth Keyboard User Manual * FCC: Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference; and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. WARNING: Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. CE Statement of Compliance with EU Directive This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. This device is a 2.4 GHz wideband transmission system (transceiver) intended for use in all EU member states and EFTA countries. Operating / Storage temperature: 0°C ~ +40°C / -40°C ~ +65°C. * ON OFF KT-1332 Bluetooth Keyboard User Manual ENGLISH B.Touchpadgestures 1.Finger slide2.Right edge swipe move the pointer. Swipe from the right edge to launch the Charms bar. 3.Tap/Double tap4.Top edge swipe In the Start screen, tap an app to launch it. InDesktop mode, double-tap an itemto launch it. • • In the Start screen, swipe from the top edge to launch Customize bar (or All apps bar in Winbdows 8). In a running app, swipe from the top edge to show commands for the current app. • • 5.Left edge swipe6.Zoom in Swipe in from the left edge to open a recently used app. touchpad. *Bluetooth pairing indicator LED <Fn>+Enable or disable the touchpad <Fn>+Turn the volume up <Fn>+Search Charms in Win8 <Fn>+Share Charm in Win8 <Fn>+Device Charm in Win8 <Fn>+Setting Charm in Win8 <Fn>+Scan previous track <Fn>+Play/Pause <Fn>+Scan next track <Fn>+Stop <Fn>+ <Fn>+Turn the volume down NOTE: Ensure that a second display is connectedtoyourTablet PC. C.Fn + Function keys A.Hardwaresetup Turn the speaker on or o WARNING! Keep yourKT-1325away from electromagnetic devices, especially navigational aids and transmission devices such as antennas and routers. *Keyboard power on/o LED White: keyboard power on Amber: Battery low or in charging. *Application key In the Start screen, select an app and press this key to launch the settings bar. In Desktop mode, press this key to simulate the right click function. *Touch pad Allows you to use multi-gestures to navigate onscreen, and functions as a regular mouse. *Function keys Press FN plus these keys to perform dierent tasks on your Tablet PC *Windows key Press this key will go back to the Start screen or the last app you opened. *Micro USB (type B) port Use this port charge the battery pack. *3-Way Switch for Power on/o and Bluetooth pairing. Switch this key to turn on/o keyboard. To put in pairing mode: Turn on Bluetooth for one second and release, the Bluetooth LED starts blinking, and select KT-1332 on your tablet PC.

Chicony Electronics Co., Ltd. NO. 25, Wu-Gong 6th Rd., Wugu Dist., New Taipei City 248, Taiwan, R.O.C Tel: 886-2-22988120 Fax: 886-2-22989745 Federal Communications Commission Authorization and Evaluation Division Date: 11/18/2013 Confidentiality Request FCC ID: E8HKT-1332 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Thank you! Sincerely yours, ------------------------------------------ T.S.Chen / Manager Chicony Electronics Co., Ltd. Tel: +886 2-2298-8120 Fax: +886 2-2298-9745 E-mail : [email protected]

Chicony Electronics Co., Ltd. NO. 25, Wu-Gong 6th Rd., Wugu Dist., New Taipei City 248, Taiwan, R.O.C Tel: 886-2-22988120 Fax: 886-2-22989745 Date: 2013-11-19 FCC ID: E8HKT-1332 AUTHORIZATION LETTER To whom it may concern: We, the undersigned Chicony Electronics Co., Ltd. hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all matters relating to all processes required in FCC Part 15C and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan on our behalf shall have the same effects as acts of our own. 1. FCC ID:E8HKT-1332 for model: KT-1332 If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, ------------------------------------------ T.S.Chen / Manager Chicony Electronics Co., Ltd. Tel: +886 2-2298-8120 Fax: +886 2-2298-9745 E-mail : [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3 Page 4 Page 5 Page 6

Page 7 Page 8 Page 9 Page 10 Page 11 Page 12

FCC ID: E8HKT-1332 Report No.: RF131108D05 Operational Description The device is a Frequency Hopping device with 79 hopping frequencies. The antenna type is PCB antenna and there is no antenna connector used. The EUT is a unit that contains a Bluetooth radio module. Bluetooth is a short-range wireless technology operating in the 2.4GHz band. It enables devices to have the ability to form networks and exchange information. The other instruction, please have a look at the user’s manual.

Report No.: SA131108D05 1 of 6 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA131108D05 MODEL NO.: KT-1332 FCC ID: E8HKT-1332 RECEIVED: Nov. 8, 2013 TESTED: Nov. 13, 2013 ISSUED: Nov. 18, 2013 APPLICANT: Chicony Electronics Co., Ltd. ADDRESS: NO. 25, Wu-Gong 6th Rd., Wugu Dist., New Taipei City 248, Taiwan, R.O.C ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB LOCATION: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C. ) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: SA131108D05 2 of 6 Report Format Version 5.0.0 Table of Contents RELEASE CONTROL RECORD .............................................................................................. 3 1. CERTIFICATION ........................................................................................................... 4 2. EVALUATION RESULT ................................................................................................. 5 3. SAR TEST EXCLUSION THRESHOLDS ..................................................................... 6 4. CONCLUSION .............................................................................................................. 6 Report No.: SA131108D05 3 of 6 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA131108D05 Original release. Nov. 18, 2013 Report No.: SA131108D05 4 of 6 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT: Bluetooth Keyboard BRAND: Chicony MODEL NO.: KT-1332 APPLICANT: Chicony Electronics Co., Ltd. TESTED: Nov. 13, 2013 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1093) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE:Nov. 18, 2013 ( Annie Chang / Supervisor ) APPROVED BY : , DATE:Nov. 18, 2013 ( Rex Lai / Assistant Manager ) Report No.: SA131108D05 5 of 6 Report Format Version 5.0.0 2. EVALUATION RESULT Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,16 where  f(GHz) is the RF channel transmit frequency in GHz .  Power and distance are rounded to the nearest mW and mm before calculation.  The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance - 50mm)·( f(MHz)/150)] mW, at 100MHz to 1500 MHz b) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW at > 1500 MHz and ≤ 6 GHz 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by ½ for test separation distances ≤ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. Report No.: SA131108D05 6 of 6 Report Format Version 5.0.0 3. SAR TEST EXCLUSION THRESHOLDS Maximum measured transmitter power: Frequency (GHz) Max. Power (mW) Min. test separation distance (mm) SAR test exclusion calculation value (NOTE 2) 1-g SAR test exclusion thresholds Result 2.402 ~ 2.480 0.6 5 0.186 3 Pass NOTE: 1. The antenna type is PCB antenna with -8.57dBi gain. 2. Calculate SAR test exclusion thresholds from condition “1” formulas. 4. CONCLUSION Since Source-base time average power is below SAR test exclusion power thresholds, the SAR evaluation is not required.

Report No.: RF131108D05 1 of 45 Report Format Version 5.0.1 FCC TEST REPORT REPORT NO.: RF131108D05 MODEL NO.: KT-1332 FCC ID: E8HKT-1332 RECEIVED: Nov. 8, 2013 TESTED: Nov. 13, 2013 ISSUED: Nov. 18, 2013 APPLICANT: Chicony Electronics Co., Ltd. ADDRESS: NO. 25, Wu-Gong 6th Rd., Wugu Dist., New Taipei City 248, Taiwan, R.O.C ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB LOCATION: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C. ) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF131108D05 2 of 45 Report Format Version 5.0.1 Table of Contents RELEASE CONTROL RECORD ................................................................................. 4 1. CERTIFICATION ............................................................................................... 5 2. SUMMARY OF TEST RESULTS ...................................................................... 6 2.1 MEASUREMENT UNCERTAINTY .................................................................... 6 3. GENERAL INFORMATION ............................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ................................................................. 7 3.2 DESCRIPTION OF TEST MODES ................................................................... 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .................... 9 3.3 DESCRIPTION OF SUPPORT UNITS ........................................................... 11 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ............................................. 11 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ................................. 12 4. TEST TYPES AND RESULTS ........................................................................ 13 4.1 CONDUCTED EMISSION MEASUREMENT .................................................. 26 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ............................... 26 4.1.2 TEST INSTRUMENTS .................................................................................... 26 4.1.3 TEST PROCEDURES .................................................................................... 27 4.1.4 DEVIATION FROM TEST STANDARD ........................................................... 27 4.1.5 TEST SETUP .................................................................................................. 28 4.1.6 EUT OPERATING CONDITIONS ................................................................... 28 4.1.7 TEST RESULTS ............................................................................................. 29 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT ......................... 13 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ....... 13 4.2.2 TEST INSTRUMENTS .................................................................................... 14 4.2.3 TEST PROCEDURES .................................................................................... 15 4.2.4 DEVIATION FROM TEST STANDARD ........................................................... 15 4.2.5 TEST SETUP .................................................................................................. 16 4.2.6 EUT OPERATING CONDITIONS ................................................................... 17 4.2.7 TEST RESULTS ............................................................................................. 18 4.3 NUMBER OF HOPPING FREQUENCY USED ............................................... 31 4.3.1 LIMIT OF HOPPING FREQUENCY USED ..................................................... 31 4.3.2 TEST SETUP .................................................................................................. 31 4.3.3 TEST INSTRUMENTS .................................................................................... 31 4.3.4 TEST PROCEDURES .................................................................................... 31 4.3.5 DEVIATION FROM TEST STANDARD ........................................................... 31 4.3.6 TEST RESULTS ............................................................................................. 31 4.4 DWELL TIME ON EACH CHANNEL ............................................................... 33 4.4.1 LIMIT OF DWELL TIME USED ....................................................................... 33 4.4.2 TEST SETUP .................................................................................................. 33 4.4.3 TEST INSTRUMENTS .................................................................................... 33 4.4.4 TEST PROCEDURES ...............…

Text truncated - open the document above for the full version.

1 of 3 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST (Mode A) 2 of 3 RADIATED EMISSION TEST (Mode A) 3 of 3 RADIATED EMISSION TEST (Mode B)