E8HMT-1022Bluetooth Laser Mouse

Bluetooth Laser Mouse MT-1022 This Bluetooth Laser mouse is an eye catch design, comfortable in either hand. High resolution technology can bring you more convenience and efficiency. It has 1200 dpi high resolution and a reliable and accurate movement. No mouse pad required and no cleaning necessary. With driverless design, you can operate the mouse by using current most popular Bluetooth compatible laptop to pare with using without cable limitation. Just follow up the system Bluetooth manager, search and assign the MT-1022 as the control device for your PC or laptop. z To pair the mouse, push and hold down the button on bottom of mouse, until light quick flashes blue at mouse left side. z Go into add new Bluetooth device then add the mouse. Lights will off after paring completed. The system requirements to ensure full compatibility are as follows: PC Operating System -- Windows® 7/VISTA / XP / 2000 Note: Do not move Laser mouse on following surface - Glass or any transparent materials Dark surface Mirror or reflecting surface Mouse pad with too many colors Rough surface FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT FCC Compliance and Advisory Statement: This hardware device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed or used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) reorient or relocate the receiving antenna; 2) increase the separation between the equipment and the receiver; 3)connect the equipment to an outlet on a circuit different from that to which the receiver is connected; 4) consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Where shielded interface cables have been provided with the product or specified additional components or accessories elsewhere defined to be used with the installation of the product, they must be used in order to ensure compliance with FCC regulations.

Page: 1

FCC ID: E8HMT-1022 FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Label

Page: 2 Page: 3 Page: 4

FCC ID: E8HMT-1022 Report No.: RF990824D01 Operational Description The transmitter of the EUT (Bluetooth Laser Mouse) is powered by 3Vdc from batteries. The type of antenna is Printed Antenna. The output power of this device is very low. Under normal use condition, the transmitter and the receiver are quite close, so high EIRP power is neither necessary nor allowed because of interference.

Report No: SA990824D01 1 Report Format Version 3.0.1 RF EXPOSURE REPORT REPORT NO.: SA990824D01 MODEL NO.: MT-1022 FCC ID: E8HMT-1022 ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT : Chicony Electronics Co., Ltd. ADDRESS : No. 25, Wu-Gong 6th Rd., Wu Ku Industrial Park, Taipei Hsien, Taiwan, R.O.C. ISSUED BY : Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS : No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien, 244 Taiwan Report No: SA990824D01 2 Report Format Version 3.0.1 Conclusion No Evaluation Required if power is below this threshold: F(GHz) mW Low 2.402 High 2.480 24.58 Maximum measured transmitter power: Pout (dBm) Pout (mW) Conducted Power -0.9 0.8 EIRP Power -4.0 0.4 *Note: The antenna is Printed antenna with -3.12dBi gain Threshold for no SAR evaluation is 24.58mW Transmitter power is 0.8mW Conclusion: No SAR evaluation required since Transmitter Pout is below FCC threshold ---END---

Report No.: RF990824D01 1 Report Format Version 3.0.1 FCC TEST REPORT REPORT NO.: RF990824D01 MODEL NO.: MT-1022 FCC ID: E8HMT-1022 RECEIVED: Aug. 24, 2010 TESTED: Aug. 24 ~ 25, 2010 ISSUED: Aug. 31, 2010 APPLICANT: Chicony Electronics Co., Ltd. ADDRESS: No. 25, Wu-Gong 6th Rd., Wu Ku Industrial Park, Taipei Hsien, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB LOCATION: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien, 244 Taiwan This test report consists of 41 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by TAF or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF990824D01 2 Report Format Version 3.0.1 TABLE OF CONTENTS 1. CERTIFICATION........................................................................................4 2. SUMMARY OF TEST RESULTS...............................................................5 2.1 MEASUREMENT UNCERTAINTY.............................................................6 3. GENERAL INFORMATION........................................................................7 3.1 GENERAL DESCRIPTION OF EUT..........................................................7 3.2 DESCRIPTION OF TEST MODES............................................................8 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST........................................8 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL.............9 3.3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS..........................10 3.3.4 DESCRIPTION OF SUPPORT UNITS.....................................................10 4. TEST TYPES AND RESULTS..................................................................11 4.1 CONDUCTED EMISSION MEASUREMENT...........................................11 4.2 RADIATED EMISSION MEASUREMENT................................................11 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT.............................11 4.2.2 TEST INSTRUMENTS.............................................................................12 4.2.3 TEST PROCEDURES.............................................................................13 4.2.4 DEVIATION FROM TEST STANDARD....................................................13 4.2.5 TEST SETUP...........................................................................................14 4.2.6 EUT OPERATING CONDITIONS.............................................................14 4.2.7 TEST RESULTS......................................................................................15 4.3 NUMBER OF HOPPING FREQUENCY USED........................................20 4.3.1 LIMIT OF HOPPING FREQUENCY USED..............................................20 4.3.2 TEST INSTRUMENTS.............................................................................20 4.3.3 TEST PROCEDURES.............................................................................20 4.3.4 DEVIATION FROM TEST STANDARD....................................................21 4.3.5 TEST SETUP...........................................................................................21 4.3.6 TEST RESULTS......................................................................................21 4.4 DWELL TIME ON EACH CHANNEL........................................................23 4.4.1 LIMIT OF DWELL TIME USED................................................................23 4.4.2 TEST INSTRUMENTS.............................................................................23 4.4.3 TEST PROCEDURES.............................................................................23 4.4.4 DEVIATION FROM TEST STANDARD....................................................23 4.4.5 TEST SETUP...........................................................................................24 4.4.6 TEST RESULTS......................................................................................24 4.5 CHANNEL BANDWIDTH.........................................................................27 4.5.1 LIMITS OF CHANNEL BANDWIDTH.......................................................27 4.5.2 TEST INSTRUMENTS.............................................................................27 4.5.3 TEST PROCEDURE................................................................................27 4.5.4 DEVIATION FROM TEST STANDARD....................................................28 4.5.5 TEST SETUP...........................................................................................28 4.5.6 EUT OPERATING CONDITION...............................................................28 4.5.7 TEST RESULTS......................................................................................29 Report No.: RF990824D01 3 Report Format Version 3.0.1 4.6 HOPPING CHANNEL SEPARATION.......................................................30 4.6.1 LIMIT OF HOPPING CHANNEL SEPARATION.......................................30 4.6.2 TEST INSTRUMENTS.............................................................................30 4.6.3 TEST PROCEDURES.............................................................................30 4.6.4 DEVIATION FROM TEST STANDARD....................................................30 4.6.5 TEST SETUP...........................................................................................30 4.6.6 TEST RESULTS......................................................................................31 4.7 MAXIMUM PEAK OUTPUT POWER.......................................................32 4.7.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT........32 4.7.2 TEST INSTRUMENTS.............................................................................32 4.7.3 TEST PROCEDURES........................................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST