Copyright © 2013 Linear LLC 235166 AX1 ITIFOB014-BUTTONKEY FOBTRANSMITTEROperation Instructions PRODUCT DESCRIPTION The Model ITIFOB01 is a four button, battery powered, water-resistant, transmitter designed for use with GE security systems.Pressing one of the buttons on the transmitter sends a digital coded wireless signal to its companion receiver and lights the red signal indicator on the transmitter. The transmitter sends variations of the code depending on which button is pressed. The code format features over 4 billion different encrypted code sequences. To ensure sending a signal, press the transmitter button for a minimum of 2 seconds.Each transmitter is powered by two self-contained type CR2025 3-volt lithium batteries (included). Every activation, the transmitter sends its battery status to the receiver. If the battery is low, a low battery signal is sent to the receiver.Receivers must be programmed to the transmitter’s code before system testing and operation. Refer to the receiver’s instructions for details on operation and programming.The transmitter is supplied with an optional mounting bracket and a belt clip. For stationary applications, the transmitter snaps into the mounting bracket. For portable use, the belt clip attaches to mounting bracket allowing the unit to be clipped to shirt pocket or slid onto a belt. FEATURES PROGRAMMING BATTERY REPLACEMENT LINEAR LIMITED WARRANTY USA & Canada (800) 421-1587 & (800) 392-0123 (760) 438-7000 - Toll Free FAX (800) 468-1340 www.linearcorp.com PRINTER’S INSTRUCTIONS: INSTR,INSTL,ITI/GE 4 BTN FOB - FILE NAME: 235166 AX1 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 5.500” - FOLDIN G: 3 FOLD ALTERNATE, FINISH WITH LOGO SHOWING - SCALE: 1-1 BELT CLIP MOUNTING BRACKET KEY FOB TRAN S MITTER ACTIVATION BUTTON S 1 TWIST COIN INSLOT TO OPENTRANSMITTER 2 CAREFULLY REMOVERETAINING SCREWAND LIFT OUT BOARD 3 REPLACE BATTERIESWITH TWO TYPE CR2025LITHIUM BATTERIESPLUS SIDE DOWN CR2025 4 REVERSE STEPS TOREASSEMBLE TRANSMITTER BE CAREFUL NOT TO DROP SCREW ON BOARD KEEP AWAY FROM SMALL CHILDREN. IF BATTERIES ARE SWALLOWED, PROMPTLY SEE A DOCTOR. DO NOT TRY TO RECHARGE THESE BATTERIES. DISPOSAL OF USED BATTERIES MUST BE MADE IN ACCORDANCE WITH THE WASTE RECOVERY AND RECYCLING REGULATIONS IN YOUR AREA. SIDE SIDE NOTICE TO USERS IN CALIFORNIA - CR COIN CELL LITHIUM BATTERY INFORMATION: THIS PRODUCT CONTAINS A CR COIN CELL LITHIUM BATTERY WHICH CONTAINS PERCHLORATE MATERIAL - SPECIAL HANDLING MAY APPLY - SEE WWW.DTSC.CA.GOV/HAZARDOUSWASTE/PERCHLORATE CR2025 1 REFER TO THE S ECURITY S Y S TEM' S IN S TRUCTION S AND PLACE THE RECEIVER IN PROGRAM MODE S ET ANY OTHER S Y S TEM PROGRAMMING OPTION S FOR THE TRAN S MITTER 2 PRE SS A BUTTON ON THE TRAN S MITTER TO S END A S IGNAL 4 TE S T THE S Y S TEM 5 VERIFY THAT THE TRAN S MITTER HA S BEEN "LEARNED" BY THE RECEIVER 3 This Linear product is warranted against defects in material and workmanship for twelve (12) months. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear LLC for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profi t, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fi tness, are valid only until the warranty expires. This Linear LLC Warranty is in lieu of all other warranties express or implied.All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical Services at 1-855-546-3351 for an RPA# and other important details. Any changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Les changements ou modifi cations non approuvés expressément par la partie responsable de la conformité pourrait annuler l’autorité de l’utilisateur à faire fonctionner l’équipement. IMPORTANT! Linear radio controls provide a reliable communications link and fi ll an important need in portable wireless signaling. However, there are some limitations which must be observed.• For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range. • A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings. • Changes or modifi cations to the device may void FCC compliance.• Infrequently used radio links should be tested regularly to protect against undetected interference or fault. • A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users. This device complies with FCC Part 15 and Canada Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Block Diagram

319.5 MHz

Cover Letter(s)

LINEAR LLC 1950 CAMINO VIDA ROBLE, SUITE 150, CARLSBAD, CA 92008-6517 PHONE (760) 438-7000 ● (800) 421-1587 ● ENG. FAX (760) 438-7043 MAIL: P.O. BOX 9003 ● CARLSBAD, CA 92018-9003 01 August 2013 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification FCC ID#: EF400106 Authority to Act as Agent On our behalf, I appoint Alan Laudani of Nemko USA Inc., 2210 Faraday Ave, STE 150, Carlsbad, CA, USA to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in Federal Communication Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with Linear L:LC, 1950 Camino Vida Roble, Suite 150, Carlsbad, CA. 92008-6517, USA. This appointment is in effect until December 31, 2013. Sincerely, John W. Kuivinen, P.E. Regulatory Compliance Engineer

Cover Letter(s)

Operational Description

CK REV. DESCRIPTION DATE APPROVED X REVISED PER ECO # Linear CARLSBAD, CA TITLE SPECIFICATIONS, DRAWN B. NYHUS DATE 28MAY13 ITIFOB01 KEYFOB TX NEXT ASSY USED ON ENGINEER SCALE NONE SIZE A DRAWING NO. XXXXX REV. X APPLICATION CHECKED FILE NAME SHEET 1 OF 2 ITI/GE keyfob transmitter Model: ITIFOB01 1.0 DESCRIPTION The ITIFOB01 is a four channel, keyfob type transmitter operating as a low power communication device. The center frequency is 319.508 MHz. The data output is formatted for use with ITI/GE security consoles. The transmitter case is black plastic, and has four silicone buttons on the front. Two lithium coin cell batteries, type 2025, are included. A mounting bracket/belt clip is included. The batteries should last about 5 years under normal use. 2.0 FUNCTION The ITIFOB01 is activated by pressing any one of the four buttons. Until activation, microprocessor, U1, is in sleep mode. Upon activation, U1 wakes up and outputs the data signal to transmitter IC, U2. U2 outputs the signal through the antenna which is a an etched trace on the PC board. 3.0 SPECIFICATIONS Product Identification: ITIFOB01 four channel mini transmitter Encoding Format: ITI/GE security. Encoding Technique: Transmitters are coded with transmitter ID number. Number of Channels: Four. Transmit frequency 319.508.00 MHz ±8kHz Power Requirements: Two 2025 3 volt batteries. Visual Indicator: Red LED. Operating Temperature: 0° C to +70° C. Tested –30° C to 70° C. Size: 2.25" x 1.3" x 0.5” (approximately). Current Consumption: 12 mA (average) transmitting. <.5 uA Standby. All specification are nominal unless otherwise noted.

RF Exposure Info

Evaluation of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01where: S = power density P = power input to the antennaG = power gain of the antenna in the direction of interest relative to an isotropic radiatorR = distance to the center of radiation of the antenna 72.8 dBuV/m From test report's measured radiated power. 3 m 0.00437 V =10 ((72.8-120)/20) 5.66914E-06 W= (( V x 3m/5.5 ) 2 ) Maximum peak output power --Radiated: 0.0000057 (W) Antenna gain(typical): 0.00 (dBi) Maximum antenna gain: 1.00 (numeric) Evaluation distance: 20.00 (cm) Evaluation frequency: 319.50 (MHz) Limit from table below: 0.213 (mW/cm^2) Power density at Evaluation frequency: 0.00000113 (mW/cm^2) EUT complies 2 4 R PG S   FCC/LSGAC Local Official’s Guide to RFA LOCAL GOVERNMENT OFFICIAL'S GUIDE TO TRANSMITTING ANTENNA RFEMISSION SAFETY: RULES, PROCEDURES, AND PRACTICAL GUIDANCE

Test Report

Nemko USA, Inc. 2210 Faraday Ave, Suite 150 Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC Part 15 Subpart C, 15.231: 29/03/2012 Certification Test Report In Accordance With: FCC Part 15 Subpart C, 15.231 RSS-210 Issue 8, December 2010 Applicant: Linear 1950 Camino Vida Roble Carlsbad, CA 92003 Equipment Under Test (EUT): 4 Button Remote Control Transmitter Model: ITIFOB01 FCC ID: EF400106 IC ID: 1078A-00106 Tested By: Nemko USA Inc. 2210 Faraday Avenue, Suite 150 Carlsbad, CA 92008 Test Report Number: 2013 08242378 FCC Date: August 8, 2013 Project Number 10249030 NEX Number 242378 Total Number of Pages: 25 Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC ID: EF400106 Report Number: 2013 08242378 FCC IC ID: 1078A-00106 Specification: FCC Part 15 Subpart C, 15.231 RSS-210 Issue 8, December 2010 Page C1 of 25 Applicant Affirmation John Kuivinen representing Linear hereby affirms: a) That he/she has reviewed and concurs that the test shown in this report are reflective of the operational characteristics of the device for which certification is sought; b) That the device in this test report will be representative of production units; c) That all changes (in hardware and software/firmware) to the subject device will be reviewed. d) That any changes impacting the attributes, functionality or operational characteristics documented in this report will be communicated to the body responsible for approving (certifying) the subject equipment. John Kuivinen Printed name of official Signature of official 1950 Camino Vida Roble August 8, 2013 Address Date 760-438-7138 [email protected] Telephone number Email address of official NOTE—This affirmation must be signed by the responsible party before it is submitted to a regulatory body for approval. Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC ID: EF400106 Report Number: 2013 08242378 FCC IC ID: 1078A-00106 Specification: FCC Part 15 Subpart C, 15.231 RSS-210 Issue 8, December 2010 Page C2 of 25 Section 1. Summary of Test Results 1.1 General All measurements are traceable to national standards These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with Part 15; Subpart C. Radiated tests were conducted is accordance with ANSI C63.4-2003. Radiated emissions are made on an open area test site. A description of the test facility is on file with the FCC. The assessment summary is as follows: Apparatus Assessed: 4 Button Remote Control Transmitter Model: FOB01 Specification: FCC Part 15 Subpart C, 15.231 RSS-210 Issue 8, December 2010 Date Received in Laboratory: July 31, 2013 Compliance Status: Complies Exclusions: None Non-compliances: None Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC ID: EF400106 Report Number: 2013 08242378 FCC IC ID: 1078A-00106 Specification: FCC Part 15 Subpart C, 15.231 RSS-210 Issue 8, December 2010 Page C3 of 25 1.2 Report Release History REVISION DATE COMMENTS - August 8, 2013 Prepared By: A. Laudani - August 8, 2013 Initial Release: Alan Laudani Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. Nemko USA Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko USA Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. Alan Laudani, Test Report Verificator Senior RF/EMC Engineer Nemko USA, Inc. 2210 Faraday Avenue, Suite 150, Carlsbad, CA 92008 Phone (760) 444-3500 Fax (760) 444-3005 FCC ID: EF400106 Report Number: 2013 08242378 FCC IC ID: 1078A-00106 Specification: FCC Part 15 Subpart C, 15.231 RSS-210 Issue 8, December 2010 Page C4 of 25 TABLE OF CONTENTS Applicant Affirmation .................................................................................................. 1 Section 1. Summary of Test Results .................................................................... 2 1.1 General ........................................................................................................ 2 1.2 Report Release History ................................................................................ 3 Section 2: Equipment Under Test .............................................................................. 5 2.1 Theory of Operation ..................................................................................... 5 2.2 Technical Specifications of the EUT ............................................................ 5 Section 3: Test Conditions ......................................................................................... 6 3.1 Specifications .............................................................................................. 6 3.2 Test Environment ........................................................................................ 6 3.3 Test Equipment ........................................................................................... 7 Section 4: Observations ............................................................................................. 7 4.1 Modifications Performed During Assessment .............................................. 7 4.2 Record Of Technical Judgements ............................................................... 7 4.3 EUT Parameters Affecting Compliance ....................................................... 7 4.4 Tests Deleted .......................…

Text truncated - open the document above for the full version.