EF400211System Controller

EL-SC-300 System Controller Quick Install Guide QUICK INSTALL GUIDE 2 IMPORTANT SAFETY INSTRUCTIONS 1. Read, understand and follow ALL safety and installation instructions included in this manual. Failure to follow the included documentation may damage the product and will void manufacturer’s warranty. 2. Follow ALL installation guidelines included with the product. Installation of the product in high humidity environments, in close proximity to heat sources and /or non-recommended locations will impede, interfere and/or damage the intended operation of the product. 3. Only use attachments and accessories which have been specified for use by the manufacturer. 4. The use of abrasive, liquid or solvent based cleaning fluids will damage the product. Please refer and follow all Product Care instructions included with the product. 5. Product Servicing may only be completed by authorized or certified service centers & personnel. For a complete list of product servicing options, please follow instructions included in the product documentation and /or contact original manufacturer for details. FCC and IC Information: This Class B digital apparatus complies with Part 15 of the FCC rules and with Canadian ICES-003 and R S S -247. RESTRICTIONS IN THE 5 GHZ BAND: Within the 5.15 to 5.25 GHz band, UNII devices will be restricted to indoor operations. Operation is subject to the following two conditions: 1. This device may not cause interference and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003 et RSS-247. RESTRICTIONS DANS LA BANDE DE 5 GHZ: Dans la bande de 5,15 à 5,25 GHz, les appareils UNII seront restreints aux opérations. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d’interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC and IC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the exemption from the routine evaluation limits in section 2.5 of RSS 102. 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters from user and bystanders. Warning: The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102, and users can obtain Canadian information on RF exposure and compliance from the Canadian Representative Nortek Control at Tel: 604-765-6933. To maintain compliance, only the antenna types that have been tested shall be used. This radio transmitter [IC: 1078A-00211] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. EL-SC-300 3 Le présent émetteur radio [IC: 1078A-00211] a ét approuvpar Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d’antenne énumérés cidessous et ayant un gain admissible maximal. Les types d’antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqu?pour tout type figurant sur la liste, sont trictement interdits pour l’exploitation de l’émetteur. Antenna Manufacturer: JIADE WIRELESS TECHNOLOGY (SHEN ZHEN) Co., LTD Model number: JD-B3DB-SMA; Gain (dBi): 3; VSWR: 1.92. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/ TV technician for help. La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite ‘exposition aux fréquences radio d’Industry Canada (IC). Utilisez l’appareil de sans fil de façon à minimiser les contacts humains lors du fonctionnement normal. Ce périphérique a également été évalué et démontré conforme aux limites d’exposition aux RF d’IC dans des conditions d’exposition à des appareils mobiles (antennes sont supérieures à 20 cm à partir du corps d’une personne). FCC and IC Registrations FCC ID: EF400211 IC: 1078A-00211 Z-Wave Operating Frequency Australia/New Zealand: 919.8, 921.4 MHz US/Canada: 908.40, 908.42, 916 MHz European: 868.40, 868.42, 869.85 MHz Z-Wave Developer’s Kit: 7.13.1 This product can be operated in any Z-Wave™ network with other Z-Wave certified devices from other manufacturers. All mains operated nodes within the network wi…

Text truncated - open the document above for the full version.

Access Control | Security & Home Automation | Health & Wellness | Home Technology 1950 Camino Vida Roble Suite 150 Carlsbad CA 92008 800.421.1587 www.nortekcontrol.com 5/13/2020 Federal Communications Commission 445 12th Street, SW Washington, DC 20554 This is a letter of authorization to accept Horsen Ma of Nortek Security & Control LLC, to sign documentation on my behalf, make representations on my behalf, and to receive and exchange data in connection with FCC certification of all Nortek Security & Control LLC products on my behalf. If you have any questions or need additional information, please feel free to give me a call at (760) 438-7179 Sincerely, Josh Hansen Engineering Manager, Regulatory & Compliance

Access Control | Security & Home Automation | Health & Wellness | Home Technology 5919 Sea Otter Place, Suite 100, Carlsbad CA 92010 800.421.1587 www.nortekcontrol.com QF094234 Page 1 of 1 Revision 0 Authority to Act as Agent Date: _2020-12-31_ TUV Rheinland Group 762 Park Avenue Youngsville, NC 27596 To Whom It May Concern: I appoint TUV Rheinland (Shenzhen) Co., Ltd. to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the FCC or Industry Canada’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by TUV Rheinland Group, still resides with Nortek Security & Control LLC For TCB applications, We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, By: Horsen Ma (Signature) (Print name) Title: Senior Manager, Hardware Engineering Telephone: +86 755 2751 1888 On behalf of: Nortek Security & Control LLC

Access Control | Security & Home Automation | Health & Wellness | Home Technology 5919 Sea Otter Place, Suite 100, Carlsbad CA 92010 800.421.1587 www.nortekcontrol.com Confidentiality Letter Date: 2021-02-01 Subject: Confidentiality Request for FCC ID: EF400211, IC: 1078A-00211 Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC/IC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term Permanent External Photos Short Term Permanent Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Part List/Tune-Up Procedure Short Term Permanent Schematics Short Term Permanent Test Setup Photos Short Term Permanent User’s Manual Nortek Security & Control LLC has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TUV Rheinland in the event information regarding the product or the product is made available to the public. TUV Rheinland will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Sincerely, Sr. Manager Hardware Engineering By: Horsen Ma (Signature/Title) (Print name)

Antenna Declaration To who concern, According to antenna requirement - section 15.203 and KDB 353028 D01 Antennas Part 15 Transmitters v01, We Nortek Security & Control LLC, hereby declare that the following description about the antenna can be used to demonstrate compliance. i) Professional installation must be justified in the filing, and grant condition must state “This device must be professionally installed.” N/A ii) Professional installation does not permit use of any antenna with the transmitter; the permitted types of antenna must be specified. Yes, the device has an external antenna, which not permit uses of any antenna with the transmitter; the permitted types of antenna must be specified as below: Antenna Manufacturer: JIADE WIRELESS TECHNOLOGY (SHEN ZHEN) Co., LTD Model number: JD-B3DB-SMA; Gain (dBi): 3; VSWR: 1.92 iii) The applicant should address the following items when justifying professional installation. (1) To qualify for professional installation, the applicant must explain why the hardware is not readily available to average consumer. This device requires a Signciant technology engineering expertise towards understanding of the tools and relevant technology, not readily available to average consumer. Only a person professionally trained in the technology is competent. (2) Marketing—Device cannot be sold via retail to the general public or by mail order; it must be sold to authorized dealers or installers only. Yes, this device is not directly marketed or sold to general public. (3) Filing must show that intended use is not for consumers and general public; rather device is generally for industrial/commercial use. Yes, the device is not for consumers and general public (4) Explain what is unique, sophisticated, complex, or specialized about the equipment that requires it to be installed by a professional installer? Yes, the functions of this device supported include the following 8 X RJ45 RS-232 port, 2 X RJ45 RS-485 port, 12 X IR Output, 4 X Voltage Detection, 6 X Relay,1 X RJ45 LAN/POE, and WIFI(2.4GHz&5GHz) connection, etc. must be setup by a professional installer. iv) Other professional installation requirements. (1) Installation must be controlled. Yes, only a person professionally trained in the technology is permitted to install it. (2) Installed by licensed professionals (e.g., device sold to dealer who hire installers). Yes, only a person professionally is trained and approved in the technology by the manufacture. (3) Installation requires special training (e.g., special programming, access to keypad, field strength measurements made). Yes, this device requires a signicant technology engineering expertise. Sincerely, 2021-03-04 Sr. Manager Hardware Engineering By: Horsen Ma (Signature/Title) (Print name)

ATTACHMENT 3 Photo Documentation Page 1 of 6 Report No.: 60424873 001 Product: System Controller Type Designation: EL-SC-300 Figure 1. External view Figure 2. External view ATTACHMENT 3 Photo Documentation Page 2 of 6 Report No.: 60424873 001 Product: System Controller Type Designation: EL-SC-300 Figure 3. Terminal view Figure 4. Terminal view

ATTACHMENT 3 Photo Documentation Page 3 of 6 Report No.: 60424873 001 Product: System Controller Type Designation: EL-SC-300 Figure 5. Internal view Figure 6. Internal view ATTACHMENT 3 Photo Documentation Page 4 of 6 Report No.: 60424873 001 Product: System Controller Type Designation: EL-SC-300 Figure 7. Internal view Figure 8. Top view of mainboard ATTACHMENT 3 Photo Documentation Page 5 of 6 Report No.: 60424873 001 Product: System Controller Type Designation: EL-SC-300 Figure 9. Bottom view of mainboard Figure 10. Top view of button board ATTACHMENT 3 Photo Documentation Page 6 of 6 Report No.: 60424873 001 Product: System Controller Type Designation: EL-SC-300 Figure 11. Bottom view of button board

FCC ID: EF400211 IC: 1078A-00211 1. Safety Human Exposure 1.1 Radio Frequency Exposure Compliance 1.1.1 Electromagnetic Fields Test Specification Test standard : CFR47 FCC Part 2: Section 2.1091 CFR47 FCC Part 1: Section 1.1310 FCC KDB Publication 447498 v06, section 7 RSS-102 Issue 5 March 2015, section 2.5.2 FCC requirements FCC requirement: Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 20cm normally can be maintained between the user and the device. MPE Calculation Method according to KDB 447498 v06 Power Density: S(mW/cm 2 )= PG/4πR 2 or EIRP/4πR 2 Where: S = power density (mW/cm 2 ) P = power input to the antenna (mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (cm) From the peak RF output power, the minimum mobile separation distance, d=20 cm, as well as the antenna gain (Max. 3dBi), the RF power density can be calculated as below: S(mW/cm2)= PG/4πR 2 a) EUT RF Exposure Evaluation operations, Worst Case mode Test Mode Measured conducted Power (dBm) Antenna Gain (dBi) Measured e.i.r.p (dBm) S(mW/cm 2 )= PG/4πR 2 Limit (mW/cm 2 ) 5GHz band Wi-Fi 14.25 3 17.25 0.011 1.000 2.4GHz band Wi-Fi 22.80 3 25.80 0.076 1.000 Note: simultaneous mode not supported.  IC requirements: The EUT shall comply with the requirement of RSS-102 section 2.5.2. Exemption from Routine Evaluation Limits – RF Exposure Evaluation RF exposure evaluation is required if the separation distance between the user and/or bystander and the device’s radiating element is greater than 20 cm, except when the device operates as follows: at or above 300 MHz and below 6 GHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 1.31 x 10-2 ƒ0.6834 W (adjusted for tune-up tolerance), where ƒ is in MHz; RF exposure evaluation exempted power for 2.4GHz Bands: 2.68 W RF exposure evaluation exempted power for NII bands: 4.52 W a) EUT RF Exposure Evaluation standalone operations, Worst Case mode Test Mode Measured conducted Power (dBm) Antenna Gain (dBi) Measured e.i.r.p Limit (w) (dBm) (W) 5GHz band Wi-Fi 14.25 3 17.25 0.05 2.68 2.4GHz band Wi-Fi 22.80 3 25.80 0.38 4.52 Note: simultaneous mode not supported. The e.i.r.p. less than the RF exposure evaluation exempted power. So RF exposure evaluation is not required. “RF Radiation Exposure Statement Caution: This Transmitter must be installed to provide a separation distance of at least 20 cm from all persons.”

Prüfbericht - Produkte Test Report - Products Prüfbericht-Nr.: Test report no.: CN21VC66 002 Auftrags-Nr.: Order no.: 168289126 Seite 1 von 20 Page 1 of 20 Kunden-Referenz-Nr.: Client reference no.: N/A Auftragsdatum: Order date: 2020-11-04 Auftraggeber: Client: Nortek Security&Control LLC 5919 Sea Otter Place,Suite 100,Carlsbad,California, United States Prüfgegenstand: Test item: System Controller Bezeichnung / Typ-Nr.: Identification / Type no.: EL-SC-300 (Trademark: ELAN) Auftrags-Inhalt: Order content: FCC & IC approval Prüfgrundlage: Test specification: CFR47 FCC Part 15: Subpart C Section 15.407 CFR47 FCC Part 15: Subpart C Section 15.207 CFR47 FCC Part 15: Subpart C Section 15.209 CFR47 FCC Part 2: Section 2.1091 RSS-247 Issue 2 February 2017 RSS-Gen Issue 5 March 2019 RSS-102 Issue 5 March 2015 Wareneingangsdatum: Date of sample receipt: 2020-12-02 Please refer to Photo Document Prüfmuster-Nr.: Test sample no: A002957975-005~007 Prüfzeitraum: Testing period: 2020-12-03 – 2021-01-29 Ort der Prüfung: Place of testing: TÜV Rheinland (Shenzhen) Co., Ltd. Prüflaboratorium: Testing laboratory: TÜV Rheinland (Shenzhen) Co., Ltd. Prüfergebnis*: Test result*: Pass geprüft von: tested by: X Signed by: Jonathan Li genehmigt von: authorized by: X Signed by: Winnie Hou Datum: Date: 2021-01-29 Ausstellungsdatum: Issue date: 2021-01-29 Stellung / Position: Project Manager Stellung / Position: Technical Certifier Sonstiges / Other: FCC ID: EF400211 IC: 1078A-00211 HVIN: EL-SC-300 Zustand des Prüfgegenstandes bei Anlieferung: Condition of the test item at delivery: Prüfmuster vollständig und unbeschädigt Test item complete and undamaged * Legende: 1 = sehr gut 2 = gut 3 = befriedigend 4 = ausreichend 5 = mangelhaft P(ass) = entspricht o.g. Prüfgrundlage(n) F(ail) = entspricht nicht o.g. Prüfgrundlage(n) N/A = nicht anwendbar N/T = nicht getestet * Legend: 1 = very good 2 = good 3 = satisfactory 4 = sufficient 5 = poor P(ass) = passed a.m. test specification(s) F(ail) = failed a.m. test specification(s) N/A = not applicable N/T = not tested Dieser Prüfbericht bezieht sich nur auf das o.g. Prüfmuster und darf ohne Genehmigung der Prüfstelle nicht auszugsweise vervielfältigt werden. Dieser Bericht berechtigt nicht zur Verwendung eines Prüfzeichens. This test report only relates to the a. m. test sample. Without permission of the test center this test report is not permitted to be duplicated in extracts. This test report does not entitle to carry any test mark. TÜV Rheinland (Shenzhen) Co., Ltd. 1601 R&D Room, 1602-1604, 17-18F, Building 7 Site C, Vanke Cloud City Phase I, Xingke First Street, Xili Street, Xili Community, Nanshan District, Shenzhen 518052, P.R. China Mail: [email protected] · Web: www.tuv.com Produkte Products Prüfbericht - Nr.: Test Report No. CN21VC66 002 Seite 2 von 20 Page 2 of 20 Test Summary 5.1.1 ANTENNA REQUIREMENT RESULT: Pass 5.1.2 MAXIMUM CONDUCTED OUTPUT POWER RESULT: Pass 5.1.3 CONDUCTED POWER SPECTRAL DENSITY RESULT: Pass 5.1.4 FREQUENCY STABILITY RESULT: Pass 5.1.5 26DB BANDWIDTH, 6DB BANDWIDTH AND 99% BANDWIDTH RESULT: Pass 5.1.6 RADIATED SPURIOUS EMISSION RESULT: Pass 5.1.7 CONDUCTED EMISSION ON AC MAINS RESULT: Pass Produkte Products Prüfbericht - Nr.: Test Report No. CN21VC66 002 Seite 3 von 20 Page 3 of 20 Contents 1 GENERAL REMARKS .......................................................................................................... 4 1.1 COMPLEMENTARY MATERIALS ............................................................................................. 4 2 TEST SITES ..................................................................................................................... 4 2.1 TEST FACILITIES ............................................................................................................... 4 2.2 LIST OF TEST AND MEASUREMENT INSTRUMENTS ..................................................................... 5 2.3 TRACEABILITY.................................................................................................................. 6 2.4 CALIBRATION................................................................................................................... 6 2.5 MEASUREMENT UNCERTAINTY ............................................................................................. 6 2.6 LOCATION OF ORIGINAL DATA ............................................................................................. 6 2.7 STATUS OF FACILITY USED FOR TESTING ............................................................................... 6 3 GENERAL PRODUCT INFORMATION........................................................................................ 7 3.1 PRODUCT FUNCTION AND INTENDED USE................................................................................ 7 3.2 RATINGS AND SYSTEM DETAILS ........................................................................................... 7 3.3 INDEPENDENT OPERATION MODES ........................................................................................ 8 3.4 NOISE GENERATING AND NOISE SUPPRESSING PARTS............................................................... 8 3.5 SUBMITTED DOCUMENTS .................................................................................................... 8 4 TEST SET-UP AND OPERATION MODES................................................................................... 9 4.1 PRINCIPLE OF CONFIGURATION SELECTION ............................................................................. 9 4.2 TEST OPERATION AND TEST SOFTWARE................................................................................. 9 4.3 SPECIAL ACCESSORIES AND AUXILIARY EQUIPMENT ................................................................. 9 4.4 COUNTERMEASURES TO ACHIEVE EMC COMPLIANCE ............................................................... 9 4.5 TEST SETUP DIAGRAM .......................................................................................…

Text truncated - open the document above for the full version.

Prüfbericht - Produkte Test Report - Products Appendix B CN21VC66 002 Page 1 of 89 Appendix B: Test Results of Wi-Fi operation for U-NII-1 Band APPENDIX B: TEST RESULTS OF WI-FI OPERATION FOR U-NII-1 BAND...........................................................................1 APPENDIX B.1: TEST RESULTS OF CONDUCTED POWER SPECTRAL DENSITY......................................................................................2 Wi-Fi 802.11 a mode.....................................................................................................................................................2 Wi-Fi 802.11 n(HT20) mode..........................................................................................................................................5 Wi-Fi 802.11 n(HT40) mode..........................................................................................................................................8 Wi-Fi 802.11 ac(HT20) mode......................................................................................................................................10 Wi-Fi 802.11 ac(HT40) mode......................................................................................................................................13 Wi-Fi 802.11 ac(HT80) mode......................................................................................................................................15 APPENDIX B.2: TEST RESULTS OF FREQUENCY STABILITY............................................................................................................16 Wi-Fi 802.11 a mode (Worst case).............................................................................................................................16 APPENDIX B.3: TEST RESULTS OF 26DB BANDWIDTH................................................................................................................17 Wi-Fi 802.11 a mode...................................................................................................................................................17 Wi-Fi 802.11 n(HT20) mode........................................................................................................................................18 Wi-Fi 802.11 n(HT40) mode........................................................................................................................................20 Wi-Fi 802.11 ac(HT20) mode......................................................................................................................................21 Wi-Fi 802.11 ac(HT40) mode......................................................................................................................................22 Wi-Fi 802.11 ac(HT80) mode......................................................................................................................................23 APPENDIX B.4: TEST RESULTS OF 99% BANDWIDTH.................................................................................................................24 Wi-Fi 802.11 a mode...................................................................................................................................................24 Wi-Fi 802.11 n(HT20) mode........................................................................................................................................27 Wi-Fi 802.11 n(HT40) mode........................................................................................................................................30 Wi-Fi 802.11 ac(HT20) mode......................................................................................................................................32 Wi-Fi 802.11 ac(HT40) mode......................................................................................................................................35 Wi-Fi 802.11 ac(HT80) mode......................................................................................................................................37 APPENDIX B.5: TEST RESULTS OF RADIATED SPURIOUS EMISSIONS..............................................................................................38 30MHz - 1GHz (Worst case)........................................................................................................................................38 1GHz - 18GHz..............................................................................................................................................................40 APPENDIX B.6: TEST RESULTS OF RADIATED EMISSIONS IN RESTRICTED BANDS..............................................................................76 Wi-Fi 802.11 a mode...................................................................................................................................................76 Wi-Fi 802.11 n(HT20) mode........................................................................................................................................80 Wi-Fi 802.11 n(HT40) mode........................................................................................................................................84 Wi-Fi 802.11 ac(HT80) mode......................................................................................................................................88 Prüfbericht - Produkte Test Report - Products Appendix B CN21VC66 002 Page 2 of 89 Appendix B.1: Test Results of Conducted Power Spectral Density Wi-Fi 802.11 a mode Prüfbericht - Produkte Test Report - Products Appendix B CN21VC66 002 Page 3 of 89 Prüfbericht - Produkte Test Report - Products Appendix B CN21VC66 002 Page 4 of 89 Prüfbericht - Produkte Test Report - Products Appendix B CN21VC66 002 Page 5 of 89 Wi-Fi 802.11 n(HT20) mode Prüfbericht - Produkte Test Report - Products Appendix B CN21VC66 002 Page 6 of 89 Prüfbericht - Produkte Test Report - Products Appendix B CN21VC66 002 Page 7 of 89 Prüfbericht - Produkte Test Report - Products Appendix B CN21VC…

Text truncated - open the document above for the full version.

Prüfbericht - Produkte Test Report - Products Appendix B CN21VC66 002 Page 21 of 89 Wi-Fi 802.11 ac(HT20) mode Prüfbericht - Produkte Test Report - Products Appendix B CN21VC66 002 Page 22 of 89 Wi-Fi 802.11 ac(HT40) mode Prüfbericht - Produkte Test Report - Products Appendix B CN21VC66 002 Page 23 of 89 Wi-Fi 802.11 ac(HT80) mode Prüfbericht - Produkte Test Report - Products Appendix B CN21VC66 002 Page 24 of 89 Appendix B.4: Test Results of 99% Bandwidth Wi-Fi 802.11 a mode Prüfbericht - Produkte Test Report - Products Appendix B CN21VC66 002 Page 25 of 89 Prüfbericht - Produkte Test Report - Products Appendix B CN21VC66 002 Page 26 of 89 Prüfbericht - Produkte Test Report - Products Appendix B CN21VC66 002 Page 27 of 89 Wi-Fi 802.11 n(HT20) mode Prüfbericht - Produkte Test Report - Products Appendix B CN21VC66 002 Page 28 of 89 Prüfbericht - Produkte Test Report - Products Appendix B…

Text truncated - open the document above for the full version.