
Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
SpeakerCraft Wireless Transmitter / Wireless Receiver SC-WIR-TX / SC-WIR-RX PAS-WIR-TX/PAS-WIR-RX INSTALLATION GUIDE PRINTER’S INSTRUCTIONS: LITERATURE, OWNER'S MANUAL, SPEAKERCRAFT WIRELESS SUBWOOFER KIT - P/N: 10030659 Rev-A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND SIZE: 5.585” X 8.2676” - TOL. +/-.125" - SCALE: 1-1 - PRINT FRONT AND BACK - FOLD: SADDLE STITCH Nortek Security & Control LLC 3 Nortek Security & Control LLC 2 I mportant S afety I nformatIon 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this appara tus near water. 6. Clean only with dry cloth. 7. Install in accordance with the manufacturer’s instructions. 8. Do not install near any hea t sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat. 9. Only use attachments/accessories specified by the manufacturer . 10. Unplug this appara tus during lightning storms or when unused for long periods of time. 11.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. FCC and IC Information This device complies with Part 15 of the FCC Rules and contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference and 2. This device must accept any interference, including interference that may cause undesired operation of the device. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference byone or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver . • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. FCC AND IC Registrations FCC ID: EF400212 IC: 1078A-00212 The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B). l'appareil numérique du ciem conforme canadien peut ‐ 3 (b) / nmb ‐ 3 (b). WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC and IC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the exemption from the routine evaluation limits in section 2.5 of RSS 102. 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. FCC/IC RF Radiation Exposure Statement: CAUTION: This Transmitter must be installed to provide separation distance of at least 20cm from all persons. FCC / IC RF Radiation Déclaration d’exposition ATTENTION: Cet émetteur doit être installé pour fournir une distance de séparation d’au moins 20 cm de toute personne. WARNING: The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102, and users can obtain Canadian information on RF exposure and compliance from the Canadian Representative Product Solutions Group at Tel: (519) 763-4538. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning ash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure, that may be insufcient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. t able of C ontentS Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 FCC and IC Information .............................................3 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Transmitter Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Receiver Connection . …
Text truncated - open the document above for the full version.
Nortek Security & Control LLC Add: 5919 Sea Otter Place, STE 100, Carlsbad CA 92010, United States Date: 2021/2/25 FCC ID: EF400212 Dear Sir/Madam, We, Nortek Security & Control LLC Hereby declares the following statement for Federal Communications Commission, PCB board, circuit, structure and internal of these model(s) are the same, Only model number is different for these model: Product name: Wireless Transmitter Model no.: SC-WIR-TX, SC-WIR-RX, PAS-WIR-RX, PAS-WIR-TX Sincerely, Name/Title: Josh Hansen/Manager Engineering Company: Nortek Security & Control LLC Address: 5919 Sea Otter Place, STE 100, Carlsbad CA 92010, United States Phone: (760) 438-7179 Fax: (760) 438-7043 E-Mail: [email protected]
CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2021/2/25> Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name EF400212 SC-WIR-TX For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title: Josh Hansen/Manager Engineering Company: Nortek Security & Control LLC Address: 5919 Sea Otter Place, STE 100, Carlsbad CA 92010, United States Phone: (760) 438-7179 Fax: (760) 438-7043 E-Mail: [email protected]
Nortek Security & Control LLC 5919 Sea Otter Place, STE 100, Carlsbad CA 92010, United States Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2021/2/25 To whom it may concern: We, Nortek Security & Control LLC the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: EF400212 including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title: Josh Hansen/Manager Engineering Company: Nortek Security & Control LLC Address: 5919 Sea Otter Place, STE 100, Carlsbad CA 92010, United States Phone: (760) 438-7179 Fax: (760) 438-7043 E-Mail: [email protected]
Nortek Security & Control LLC 5919 Sea Otter Place, STE 100, Carlsbad CA 92010, United States UNII Device Declaration Letter To whom it may concern: We have declared below featured for FCC equipment authorization, Device FCC ID: EF400212 (1) DFS Device: Master Client with Radar detection capability N/A Client without radar detection capability, (2) Active / Passive Scanning , adhoc mode access point capability Frequency Band (MHz) Active Scanning (the device can transmit a probe (beacon)) passive scanning (where the device is can listen only with no probes) Ad Hoc Mode capability Access point capability 5180-5240 Yes No Yes No Yes No Yes No 5176-5814 Yes No Yes No Yes No Yes No (3) Country code selection ability Yes No If yes, pls explain how it was implemented: (4) Meet 15.202 requirement Yes No pls check below : A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network. (5) For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes cannot be modified by end user or an installer. Apply Does not apply (If apply, pls help to provide explanation on it was implement, and how software was controlled) Should you have any questions or comments regarding this matter, please have my best attention. Sincerely, (Signed) Name/Title: Josh Hansen/Manager Engineering Company: Nortek Security & Control LLC Address: 5919 Sea Otter Place, STE 100, Carlsbad CA 92010, United States Phone: (760) 438-7179 Fax: (760) 438-7043 E-Mail: [email protected]
FCC ID: EF400212 IC: 1078A-00212 TX RX FCC ID: EF400212 IC: 1078A-00212 FCC ID: EF400212 IC: 1078A-00212 FCC ID: EF400212 IC: 1078A-00212
FCC ID: EF400212 IC: 1078A-00212 Label Location FCC ID: EF400212 IC: 1078A-00212
FCC ID: EF400212 IC: 1078A-00212 ANT A ANT B FCC ID: EF400212 IC: 1078A-00212 FCC ID: EF400212 IC: 1078A-00212
RF Exposure evaluation Exposure category: General population/uncontrolled environment EUT Type: Production Unit Device Type: Mobile Device Refer Standard: KDB 447498 D01 General RF Exposure Guidance v06 FCC Part 2 §2.1091 FCC ID: EF400212 1. Reference According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1091 RF exposure is calculated. KDB447498 D01: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies 2. Limit Limits for Maximum Permissible Exposure (MPE)/Controlled Exposure Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density (mW/cm²) Averaging Time (minute) Limits for Occupational/Controlled Exposure 0.3 – 3.0 614 1.63 (100) * 6 3.0 – 30 1842/f 4.89/f (900/f 2 )* 6 30 – 300 61.4 0.163 1.0 6 300 – 1500 / / f/300 6 1500 – 100,000 / / 5 6 Limits for Maximum Permissible Exposure (MPE)/Uncontrolled Exposure Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density (mW/cm²) Averaging Time (minute) Limits for Occupational/Controlled Exposure 0.3 – 3.0 614 1.63 (100) * 30 3.0 – 30 824/f 2.19/f (180/f 2 )* 30 30 – 300 27.5 0.073 0.2 30 300 – 1500 / / f/1500 30 1500 – 100,000 / / 1.0 30 F=frequency in MHz *=Plane-wave equivalent power density 3. MPE Calculation Method Predication of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna 4. Result As declared by the Applicant, the EUT is a wireless device used in a fix application, at least 20 cm from any body part of the user or nearby persons; from the maximum EUT RF output power, the minimum separation distance, r =20cm, as well as the gain of the used 5.8G and 5.2G antenna is 2.4dBi the RF power density can be obtained. For 5.8G ANT A Freq. (MHz) Output Power (dBm) Target power / tolerance (dBm) Max tune up power tolerance (dBm) Output power to antenna (mW) Ant Gain (dBi) Power Density at R=20cm (mW/cm2) Limit (mW/c m2) Result 5736 3.145 3±1.0 4 2.512 2.4 0.00087 1 Pass 5762 3.136 3±1.0 4 2.512 2.4 0.00087 1 Pass 5814 4.091 4±1.0 5 3.162 2.4 0.00109 1 Pass For 5.8G ANT B Freq. (MHz) Output Power (dBm) Target power / tolerance (dBm) Max tune up power tolerance (dBm) Output power to antenna (mW) Ant Gain (dBi) Power Density at R=20cm (mW/cm2) Limit (mW/c m2) Result 5736 3.159 3±1.0 4 2.512 2.4 0.00087 1 Pass 5762 3.176 3±1.0 4 2.512 2.4 0.00087 1 Pass 5814 3.952 4±1.0 5 3.162 2.4 0.00109 1 Pass Note: The estimation distance is 20cm For 5.2G ANT A Freq. (MHz) Output Power (dBm) Target power / tolerance (dBm) Max tune up power tolerance (dBm) Output power to antenna (mW) Ant Gain (dBi) Power Density at R=20cm (mW/cm2) Limit (mW/c m2) Result 5180 3.414 3±1.0 4 2.512 2.4 0.00087 1 Pass 5210 3.274 3±1.0 4 2.512 2.4 0.00087 1 Pass 5240 3.985 4±1.0 5 3.162 2.4 0.00109 1 Pass For 5.2G ANT B Freq. (MHz) Output Power (dBm) Target power / tolerance (dBm) Max tune up power tolerance (dBm) Output power to antenna (mW) Ant Gain (dBi) Power Density at R=20cm (mW/cm2) Limit (mW/c m2) Result 5180 3.257 3±1.0 4 2.512 2.4 0.00087 1 Pass 5210 3.554 3±1.0 4 2.512 2.4 0.00087 1 Pass 5240 4.025 4±1.0 5 3.162 2.4 0.00109 1 Pass Note: The estimation distance is 20cm 5. Simultaneously MPE MPE Ratio 5.8G (mW/cm2) MPE Ratio 5.2G (mW/cm2) ∑MPE ratios Limit Results 0.00109 0.00109 0.00218 1.0 PASS 6. Conclusion The measurement results comply with the FCC Limit per 47 CFR 2.1091 for the uncontrolled RF Exposure of mobile device.
Page 1 of 44 FCC TEST REPORT FCC ID: EF400212 IC: 1078A-00212 Product : Wireless Transmitter Model Name : SC-WIR-TX Additional model : SC-WIR-RX, PAS-WIR-RX, PAS-WIR-TX Brand : N/A Report No. : PTC20110303604E-FC01 Prepared for Nortek Security & Control LLC 5919 Sea Otter Place, STE 100, Carlsbad CA 92010, United States Prepared by Precise Testing & Certification Co., Ltd. Building 1, No. 6, Tongxin Road, Dongcheng Street, Dongguan, Guangdong, China Report No.: PTC20110303604E-FC01 Page 2 of 44 1 Test Result Certification Applicant’s name : Nortek Security & Control LLC Address : 5919 Sea Otter Place, STE 100, Carlsbad CA 92010, United States Manufacture's name : Nortek Security & Control LLC Address : 5919 Sea Otter Place, STE 100, Carlsbad CA 92010, United States Product name : Wireless Transmitter Model name Additional model : : SC-WIR-TX SC-WIR-RX, PAS-WIR-RX, PAS-WIR-TX Standards : FCC CFR47 Part 15 Section 15.407 RSS-247 Issue 2: February 2017 RSS-Gen Issue 5 April 2018 ANSI C63.10: 2013 Test procedure : ANSI C63.10:2013 Test Date : Oct. 21, 2020 ~ Feb. 05, 2021 Date of Issue : Feb. 05, 2021 Test Result : Pass This device described above has been tested by PTC, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of PTC, this document may be altered or revised by PTC, personal only, and shall be noted in the revision of the document. Test Engineer: Technical Manager: Leo Yang / Engineer Chris Du / Manager Report No.: PTC20110303604E-FC01 Page 3 of 44 Contents Page 1 TEST RESULT CERTIFICATION ................................................................................................................... 2 2 TEST SUMMARY ............................................................................................................................................ 5 2.1 TEST SITE.......................................................................................................................................................... 5 3 GENERAL INFORMATION ............................................................................................................................ 6 3.1 GENERAL DESCRIPTION OF E.U.T. .................................................................................................................. 6 3.2 CHANNEL LIST ................................................................................................................................................... 6 4 EQUIPMENT DURING TEST.......................................................................................................................... 7 4.1 EQUIPMENTS LIST ............................................................................................................................................. 7 4.2 DESCRIPTION OF SUPPORT UNITS ................................................................................................................... 8 4.3 MEASUREMENT UNCERTAINTY ......................................................................................................................... 8 5 CONDUCTED EMISSION ............................................................................................................................... 9 5.1 CONDUCTED POWER LINE EMISSION LIMIT...................................................................................................... 9 5.2 EUT OPERATION .............................................................................................................................................. 9 5.3 TEST SETUP ...................................................................................................................................................... 9 5.4 TEST PROCEDURE ............................................................................................................................................ 9 5.5 SUMMARY OF TEST RESULTS ......................................................................................................................... 10 6 RADIATED SPURIOUS EMISSIONS ...........................................................................................................13 6.1 EUT OPERATION ............................................................................................................................................ 13 6.2 TEST SETUP .................................................................................................................................................... 14 6.3 SPECTRUM ANALYZER SETUP ........................................................................................................................ 15 6.4 TEST PROCEDURE .......................................................................................................................................... 16 6.5 SUMMARY OF TEST RESULTS ......................................................................................................................... 17 7 OCCUPIED BANDWIDTH .............................................................................................................................22 7.1 TEST LIMIT....................................................................................................................................................... 22 7.2 TEST PROCEDURE .......................................................................................................................................... 22 7.3 MEASUREMENT EQUIPMENT USED ................................................................................................................. 22 7.4 TEST RESULT .................................................................................................................................................. 22 8 PEAK OUTPUT POWER .....................................................…
Text truncated - open the document above for the full version.
Page 1 of 44 FCC TEST REPORT FCC ID: EF400212 IC: 1078A-00212 Product : Wireless Transmitter Model Name : SC-WIR-TX Additional model : SC-WIR-RX, PAS-WIR-RX, PAS-WIR-TX Brand : N/A Report No. : PTC20110303604E-FC02 Prepared for Nortek Security & Control LLC 5919 Sea Otter Place, STE 100, Carlsbad CA 92010, United States Prepared by Precise Testing & Certification Co., Ltd. Building 1, No. 6, Tongxin Road, Dongcheng Street, Dongguan, Guangdong, China Report No.: PTC20110303604E-FC02 Page 2 of 44 1 Test Result Certification Applicant’s name : Nortek Security & Control LLC Address : 5919 Sea Otter Place, STE 100, Carlsbad CA 92010, United States Manufacture's name : Nortek Security & Control LLC Address : 5919 Sea Otter Place, STE 100, Carlsbad CA 92010, United States Product name : Wireless Transmitter Model name Additional model : : SC-WIR-TX SC-WIR-RX, PAS-WIR-RX, PAS-WIR-TX Standards : FCC CFR47 Part 15 Section 15.407 RSS-247 Issue 2: February 2017 RSS-Gen Issue 5 April 2018 ANSI C63.10: 2013 Test procedure : ANSI C63.10:2013 Test Date : Oct. 21, 2020 ~ Feb. 05, 2021 Date of Issue : Feb. 05, 2021 Test Result : Pass This device described above has been tested by PTC, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of PTC, this document may be altered or revised by PTC, personal only, and shall be noted in the revision of the document. Test Engineer: Technical Manager: Leo Yang / Engineer Chris Du / Manager Report No.: PTC20110303604E-FC02 Page 3 of 44 Contents Page 1 TEST RESULT CERTIFICATION ................................................................................................................... 2 2 TEST SUMMARY ............................................................................................................................................ 5 2.1 TEST SITE.......................................................................................................................................................... 5 3 GENERAL INFORMATION ............................................................................................................................ 6 3.1 GENERAL DESCRIPTION OF E.U.T. .................................................................................................................. 6 3.2 CHANNEL LIST ................................................................................................................................................... 6 4 EQUIPMENT DURING TEST.......................................................................................................................... 7 4.1 EQUIPMENTS LIST ............................................................................................................................................. 7 4.2 DESCRIPTION OF SUPPORT UNITS ................................................................................................................... 8 4.3 MEASUREMENT UNCERTAINTY ......................................................................................................................... 8 5 CONDUCTED EMISSION ............................................................................................................................... 9 5.1 CONDUCTED POWER LINE EMISSION LIMIT...................................................................................................... 9 5.2 EUT OPERATION .............................................................................................................................................. 9 5.3 TEST SETUP ...................................................................................................................................................... 9 5.4 TEST PROCEDURE ............................................................................................................................................ 9 5.5 SUMMARY OF TEST RESULTS ......................................................................................................................... 10 6 RADIATED SPURIOUS EMISSIONS ...........................................................................................................13 6.1 EUT OPERATION ............................................................................................................................................ 13 6.2 TEST SETUP .................................................................................................................................................... 14 6.3 SPECTRUM ANALYZER SETUP ........................................................................................................................ 15 6.4 TEST PROCEDURE .......................................................................................................................................... 16 6.5 SUMMARY OF TEST RESULTS ......................................................................................................................... 17 7 OCCUPIED BANDWIDTH .............................................................................................................................22 7.1 TEST LIMIT....................................................................................................................................................... 22 7.2 TEST PROCEDURE .......................................................................................................................................... 22 7.3 MEASUREMENT EQUIPMENT USED ................................................................................................................. 22 7.4 TEST RESULT .................................................................................................................................................. 22 8 PEAK OUTPUT POWER .....................................................…
Text truncated - open the document above for the full version.
FCC ID: EF400212 IC: 1078A-00212 Radiated Emission (Below 1G) Radiated Emission (Above 1G) FCC ID: EF400212 IC: 1078A-00212 Conducted Emission
| # | Rule Parts | Frequency Range | Power Output |
|---|---|---|---|
| 2 | 15E | 5.74 GHz - 5.81 GHz | 5.00 mW |
Edge II Security Panel
Equipment Class
DSS - Part 15 Spread Spectrum TransmitterWireless KVM Extender TX+RX
Equipment Class
NII - Unlicensed National Information Infrastructure TXWireless KVM Extender TX+RX
Equipment Class
NII - Unlicensed National Information Infrastructure TXDoubleDimmer-Control
Equipment Class
DXX - Part 15 Low Power Communication Device TransmitterDigital Transmitter
Equipment Class
DSS - Part 15 Spread Spectrum Transmitter